A finite element study on posterior short segment fixation combined with unilateral fixation using pedicle screws for stable thoracolumbar fracture

Biomechanical Effects of Different Prosthesis Types and Fixation Ranges in Multisegmental Total En Bloc Spondylectomy: A Finite Element Study

OBJECTIVE

Multi-segmental total en bloc spondylectomy (TES) gradually became more commonly used by clinicians. However, the choice of surgical strategy is unclear. This study aims to investigate the biomechanical performance of different prosthesis types and fixation ranges in multisegmental TES.

METHODS

In this study, a validated finite element model of T12-L2 post-spondylectomy operations were carried out. The prostheses of these models used either 3D-printed artificial vertebrae or titanium mesh cages. The fixed range was two or three segment levels. Range of motion, stress distribution of the endplate and internal fixation system, intervertebral disc pressure, and facet joint surface force of four postoperative models and intact model in flexion and extension, as well as lateral bending and rotation were analyzed and compared.

RESULTS

The type of prosthesis used in the anterior column reconstruction mainly affected the stress of the adjacent endplate and the prosthesis itself. The posterior fixation range had a greater influence on the overall range of motion (ROM), the ROM of the adjacent segment, the stress of the screw-rod system, and adjacent facet joint surface force. For the model of the same prosthesis, the increase of fixed length resulted in an obvious reduction of ROM. The maximal decrease was 70.23% during extension, and the minimal decrease was 30.19% during rotation.

CONCLUSION

In three-segment TES, the surgical strategy of using 3D-printed artificial prosthesis for anterior column support and pedicle screws for posterior fixation at both two upper and lower levels respectively can reduce the stress on internal fixation system, endplates, and adjacent intervertebral discs, resulting in a reduced risk of internal fixation failure, and ASD development.

Biomechanical Evaluation of a Newly Developed Functional-Grade Composite Material for Pedicle Screws

OBJECTIVE

Pedicle screw and rod systems are widely employed in spine surgeries and loosening due to insufficient mechanical stimulation on the bone is frequently encountered in pedicle screws. This mechanical stimulation problem also arises due to the high rigidity of the implant material. This study aimed to develop new pedicle screws with composite material to solve the pedicle screw loosening problem.

METHODS

The vertebrae and vertebral disk were modeled in three dimension using computerized tomography images obtained from a patient. A commercially available pedicle screw was modeled using Fusion software, and all models were assembled in accordance with the surgical procedure. Pedicle screw models were also divided radially and longitudinally to resemble functionally graded materials, which are composite materials. The load was applied to the top of the T12 vertebra and the screw-vertebral system was fixed to the bottom of the L1 vertebra.

RESULTS

The strain results on the vertebrae were examined according to the mechanostat theorem. According to the results, functionally graded material (FGM) pedicle screw decreased the strain on the vertebral bones, and the positive effects on the bone were determined when using the radially functionally graded screws. The maximum stress values were also examined to determine the strengths of all the models.

CONCLUSION

In conclusion, FGM pedicle screw decreased the strain on the bone which is an important parameter for the loosening failure according to the study. The other important conclusion is that FGM pedicle screw can be the solution to the loosening of the screw but not in all vertebrae.

Hybrid kyphoplasty with short-versus intermediate- and long-segment pedicle screw fixations for the management of thoracolumbar burst fractures

BACKGROUND

This study aimed to determine if the hybrid short-segment (HSS) technique is a good alternative to the intermediate-segment (IS) and long-segment (LS) techniques in pedicle screw fixations for acute thoracolumbar burst fractures (TLBFs).

METHODS

In this retrospective evaluation, we examined 43 patients who underwent surgical treatments, including one- or two-level suprajacent (U) and infrajacent (L) pedicle screw fixations, for acute single-level TLBFs with neurological deficits between the T11 and L2 levels from July 2013 to December 2019. Among these patients, 15 individuals underwent HSS (U1L1), 12 received IS (U2L1), and 16 underwent LS (U2L2) fixations. Supplemental kyphoplasty of the fractured vertebral bodies was performed exclusively in the HSS group. Our analysis focused on assessing blood loss and surgical duration. Additionally, we compared postoperative thoracolumbar kyphotic degeneration using the data on Cobb angles on lateral radiographic images acquired at three time points (preoperatively, postoperative day 1, and follow-up). The end of follow-up was defined as the most recent postoperative radiographic image or implant complication occurrence.

RESULTS

Blood loss and surgical duration were significantly lower in the HSS group than in the IS and LS groups. Additionally, the HSS group exhibited the lowest implant complication rate (2/15, 13.33%), followed by the LS (6/16, 37.5%) and IS (8/12, 66.7%) group. Implant complications occurred at a mean follow-up of 7.5 (range: 6-9), 9 (range: 5-23), and 7 (range: 1-21) months in the HSS, IS, and LS groups. Among these implant complications, revision surgeries were performed in two patients in the HSS group, two in the IS group, and one in the LS group. One patient treated by HSS with balloon kyphoplasty underwent reoperation because of symptomatic cement leakage.

CONCLUSIONS

The HSS technique reduced intraoperative blood loss, surgical duration, and postoperative implant complications, indicating it is a good alternative to the IS and LS techniques for treating acute single-level TLBFs. This technique facilitates immediate kyphosis correction and successful maintenance of the corrected alignment within 1 year. Supplemental kyphoplasty with SpineJack® devices and high-viscosity bone cements for anterior reconstruction can potentially decrease the risk of cement leakage and related issues.

Biomechanical Comparison of Anterior Cervical Corpectomy Decompression and Fusion, Anterior Cervical Discectomy and Fusion, and Anterior Controllable Antedisplacement and Fusion in the Surgical Treatment of Multilevel Cervical Spondylotic Myelopathy: A Finite Element Analysis

PURPOSE

Multilevel cervical spondylotic myelopathy poses significant challenges in selecting optimal surgical approaches, warranting a comprehensive understanding of their biomechanical impacts. Given the lack of consensus regarding the most effective technique, this study aims to fill this critical knowledge gap by rigorously assessing and comparing the biomechanical properties of three distinct surgical interventions, including anterior controllable antedisplacement and fusion (ACAF), anterior cervical corpectomy decompression and fusion (ACCF), and anterior cervical discectomy and fusion (ACDF). The study offers pivotal insights to enhance treatment precision and patient outcomes.

METHODS

The construction of the cervical spine model involved a detailed process using CT data, specialized software (Mimics, Geomagic Studio, and Hypermesh) and material properties obtained from prior studies. Surgical instruments were modeled (titanium mesh, anterior cervical plate, interbody cage, and self-tapping screws) to simulate three surgical approaches: ACAF, ACCF, and ACDF, each with specific procedures replicating clinical protocols. A 75-N follower load with 2 Nm was applied to simulate biomechanical effects.

RESULTS

The range of motion decreased more after surgery for ACAF and ACDF than for ACCF, especially in flexion and lateral bending. ACCF have higher stress peaks in the fixation system than those of ACAF and ACDF, especially in flexion. The maximum von Mises stresses of the bone-screw interfaces at C3 of ACCF were higher than those of ACAF and ACDF. The maximum von Mises stresses of the bone-screw interfaces at C6 of ACDF were much higher than those of ACAF and ACCF. The maximum von Mises stresses of the grafts of ACCF and ACAF were much higher than those of ACDF. The maximum von Mises stresses of the endplate of ACCF were much higher than those of ACAF and ACDF.

CONCLUSION

The ACAF and ACDF models demonstrated superior cervical reconstruction stability over the ACCF model. ACAF exhibited lower risks of internal fixation failure and cage subsidence compared to ACCF, making it a promising approach. However, while ACAF revealed improved stability over ACCF, higher rates of subsidence and internal fixation failure persisted compared to ACDF, suggesting the need for further exploration of ACAF's long-term efficacy and potential improvements in clinical outcomes.

Finite element biomechanical analysis of 3D printed intervertebral fusion cage in osteoporotic population

OBJECTIVE

To study the biomechanical characteristics of each tissue structure when using different 3D printing Cage in osteoporotic patients undergoing interbody fusion.

METHODS

A finite element model of the lumbar spine was reconstructed and validated with regarding a range of motion and intervertebral disc pressure from previous in vitro studies. Cage and pedicle screws were implanted and part of the lamina, spinous process, and facet joints were removed in the L4/5 segment of the validated mode to simulate interbody fusion. A 280 N follower load and 7.5 N·m moment were applied to different postoperative models and intact osteoporotic model to simulate lumbar motion. The biomechanical characteristics of different models were evaluated by calculating and analyzing the range of motion of the fixed and cephalic adjacent segment, the stress of the screw-rod system, the stress at the interface between cage and L5 endplate, and intervertebral disc pressure of the adjacent segment.

RESULTS

After rigid fixation, the range of motion of the fixed segment of model A-C decreased significantly, which was much smaller than that of the osteoporotic model. And with the increase of the axial area of the interbody fusion cages, the fixed segment of model A-C tended to be more stable. The range of motion and intradiscal pressure of the spinal models with different interbody fusion cages were higher than those of the complete osteoporosis model, but there was no significant difference between the postoperative models. On the other hand, the L5 upper endplate stress and screw-rod system stress of model A-C show a decreasing trend in different directions of motion. The stress of the endplate is the highest during flexion, which can reach 40.5 MPa (model A). The difference in endplate stress between models A-C was the largest during lateral bending. The endplate stress of models A and B was 150.5% and 140.9% of that of model C, respectively. The stress of the screw-rod system was the highest during lateral bending (model A, 102.0 MPa), which was 108.4%, 102.4%, 110.4%, 114.2% of model B and 158.5%, 110.1%, 115.8%, 125.4% of model C in flexion, extension, lateral bending, and rotation, respectively.

CONCLUSIONS

For people with osteoporosis, no matter what type of cage is used, good immediate stability can be achieved after surgery. Larger cage sizes provide better fixation without significantly increasing ROM and IDP in adjacent segments, which may contribute to the development of ASD. In addition, larger cage sizes can disperse endplate stress and reduce stress concentration, which is of positive significance in preventing cage subsidence after operation. The cage and screw rod system establish a stress conduction pathway on the spine, and a larger cage greatly enhances the stress-bearing capacity of the front column, which can better distribute the stress of the posterior spine structure and the stress borne by the posterior screw rod system, reduce the stress concentration phenomenon of the nail rod system, and avoid exceeding the yield strength of the material, resulting in the risk of future instrument failure.

Biomechanical behaviour of a novel bone cement screw in the minimally invasive treatment of Kummell's disease: a finite element study

OBJECTIVE

To investigate and evaluate the biomechanical behaviour of a novel bone cement screw in the minimally invasive treatment of Kummell's disease (KD) by finite element (FE) analysis.

METHODS

A validated finite element model of healthy adult thoracolumbar vertebrae T12-L2 was given the osteoporotic material properties and the part of the middle bone tissue of the L1 vertebral body was removed to make it wedge-shaped. Based on these, FE model of KD was established. The FE model of KD was repaired and treated with three options: pure percutaneous vertebroplasty (Model A), novel unilateral cement screw placement (Model B), novel bilateral cement screw placement (Model C). Range of motion (ROM), maximum Von-Mises stress of T12 inferior endplate and bone cement, relative displacement of bone cement, and stress distribution of bone cement screws of three postoperative models and intact model in flexion and extension, as well as lateral bending and rotation were analyzed and compared.

RESULTS

The relative displacements of bone cement of Model B and C were similar in all actions studied, and both were smaller than that of Model A. The minimum value of relative displacement of bone cement is 0.0733 mm in the right axial rotation of Model B. The maximum Von-Mises stress in T12 lower endplate and bone cement was in Model C. The maximum Von-Mises stress of bone cement screws in Model C was less than that in Model B, and it was the most substantial in right axial rotation, which is 34%. There was no substantial difference in ROM of the three models.

CONCLUSION

The novel bone cement screw can effectively reduce the relative displacement of bone cement by improving the stability of local cement. Among them, novel unilateral cement screw placement can obtain better fixation effect, and the impact on the biomechanical environment of vertebral body is less than that of novel bilateral cement screw placement, which provides a reference for minimally invasive treatment of KD in clinical practice.

A comparative analysis of using cage acrossing the vertebral ring apophysis in normal and osteoporotic models under endplate injury: a finite element analysis

Background: Lateral lumbar fusion is an advanced, minimally invasive treatment for degenerative lumbar diseases. It involves different cage designs, primarily varying in size. This study aims to investigate the biomechanics of the long cage spanning the ring apophysis in both normal and osteoporotic models, considering endplate damage, using finite element analysis. Methods: Model 1 was an intact endplate with a long cage spanning the ring apophysis. Model 2 was an endplate decortication with a long cage spanning the ring apophysis. Model 3 was an intact endplate with a short cage. Model 4 was an endplate decortication with a short cage. On the basis of the four original models, further osteoporosis models were created, yielding a total of eight finite element models. The provided passage delineates a study that elucidates the utilization of finite element analysis as a methodology to simulate and analyze the biomechanical repercussions ensuing from the adoption of two distinct types of intervertebral fusion devices (cages) within the physiological framework of a human body. Results: The investigation found no appreciable changes between Models 1 and 2 in the range of motion at the fixed and neighboring segments, the L3-4 IDP, screw-rod stress, endplate stress, or stress on the trabecular bone of the L5. Increases in these stresses were seen in models 3 and 4 in the ranges of 0.4%-676.1%, 252.9%-526.9%, 27.3%-516.6%, and 11.4%-109.3%, respectively. The osteoporotic models for scenarios 3 and 4 exhibit a similar trend to their respective normal bone density models, but these osteoporotic models consistently have higher numerical values. In particular, except for L3-4 IDP, the maximum values of these parameters in osteoporotic Models 3 and 4 were much higher than those in normal bone quality Models 1 and 2, rising by 385.3%, 116%, 435.1%, 758.3%, and 786.1%, respectively. Conclusion: Regardless of endplate injury or osteoporosis, it is advised to utilize a long cage that is 5 mm longer on each side than the bilateral pedicles because it has good biomechanical features and may lower the likelihood of problems after surgery. Additionally, using Long cages in individuals with osteoporosis may help avoid adjacent segment disease.

Clinic choice of long or short segment pedicle screw-rod fixation in the treatment of thoracolumbar burst fracture: From scan data to numerical study

Based on computerized tomography scanning images of human lumbar vertebrae, finite element (FE) analysis is performed to predict the stress of pedicle screws, rods, and fractured vertebra as well as the displacement of fractured vertebra after internal fixation treatment of thoracolumbar burst fracture. A three-dimensional FE model of L1-L5 lumbar vertebrae with L3 burst fracture has been established and four fixation methods, namely, short segment cross- and trans-injured vertebrae, long segment cross- and trans-injured vertebrae fixations, have been adopted to perform posterior pedicle fixation. The stress distributions of the screws, rods, and fractured vertebra and the total deformation of the fractured vertebra are investigated under six different physiological motions. From the view of the stress on the screw-rod system and the deformation of the fractured vertebral body, the long segment cross-injured vertebra fixation has the best mechanical performance, followed by the long segment trans-injured vertebra fixation, and then the short segment fixation trans-injured vertebra. The short segment fixation cross-injured vertebra performs the worst. Among the six motions, the forward flexion movement has the greatest impact on the screw-rod system and the fractured vertebra. However, the rotation motion greatly affects the stress of the screw in the long segment fixation. This indicates that the longer the fixed segment is, the more susceptible it is to human rotation. Thus, for patients with severe fracture, the long segment cross-injured vertebra is preferred. On the contrary, the short segment trans-injured vertebra fixation is optimal.

Biomechanical properties of lumbar vertebral ring apophysis cage under endplate injury: a finite element analysis

OBJECTIVE

This study aimed to compare the biomechanical properties of lumbar interbody fusion involving two types of cages. The study evaluated the effectiveness of the cage spanning the ring apophysis, regardless of the endplate's integrity.

METHODS

A finite element model of the normal spine was established and validated in this study. The validated model was then utilized to simulate Lateral Lumbar Interbody Fusion (LLIF) with posterior pedicle screw fixation without posterior osteotomy. Two models of interbody fusion cage were placed at the L4/5 level, and the destruction of the bony endplate caused by curetting the cartilaginous endplate during surgery was simulated. Four models were established, including Model 1 with an intact endplate and long cage spanning the ring apophysis, Model 2 with endplate decortication and long cage spanning the ring apophysis, Model 3 with an intact endplate and short cage, and Model 4 with endplate decortication and short cage. Analyzed were the ROM of the fixed and adjacent segments, screw rod system stress, interface stress between cage and L5 endplate, trabecular bone stress on the upper surface of L5, and intervertebral disc pressure (IDP) of adjacent segments.

RESULTS

There were no significant differences in ROM and IDP between adjacent segments in each postoperative model. In the short cage model, the range of motion (ROM), contact pressure between the cage and endplate, stress in L5 cancellous bone, and stress in the screw-rod system all exhibited an increase ranging from 0.4% to 79.9%, 252.9% to 526.9%, 27.3% to 133.3%, and 11.4% to 107%, respectively. This trend was further amplified when the endplate was damaged, resulting in a maximum increase of 88.6%, 676.1%, 516.6%, and 109.3%, respectively. Regardless of the integrity of the endplate, the long cage provided greater support strength compared to the short cage.

CONCLUSIONS

Caution should be exercised during endplate preparation and cage placement to maintain the endplate's integrity. Based on preoperative X-ray evaluation, the selection of a cage that exceeds the width of the pedicle by at least 5 mm (ensuring complete coverage of the vertebral ring) has demonstrated remarkable biomechanical performance in lateral lumbar interbody fusion procedures. By opting for such a cage, we expect a reduced occurrence of complications, including cage subsidence, internal fixation system failure, and rod fracture.

Biomechanical evaluation of different sizes of 3D printed cage in lumbar interbody fusion-a finite element analysis

OBJECTIVE

To study the biomechanical characteristics of various tissue structures of different sizes of 3D printed Cage in lumbar interbody fusion.

METHODS

A finite element model of normal spine was reconstructed and verified. Pedicle screws and Cage of different sizes were implanted in the L4/5 segment to simulate lumbar interbody fusion. The range of motion of the fixed and cephalic adjacent segment, the stress of the screw-rod system, the stress at the interface between cage and L5 endplate, and intervertebral disc pressure of the adjacent segment were calculated and analyzed.

RESULTS

The range of motion and intervertebral disc pressure of the adjacent segment of each postoperative model were larger than those of the intact model, but there was not much difference between them. The stress of cage-endplate interface was also larger than that of the intact model. However, the difference is that the stress of the endplate and the screw-rod system has a tendency to decrease with the increase of the axial area of cage.

CONCLUSIONS

Cage with larger axial area in lumbar interbody fusion can reduce the stress of internal fixation system and endplate, but will not increase the range of motion and intervertebral disc pressure of adjacent segment. It has a certain effect in preventing the cage subsidence, internal fixation system failure and screw rod fracture.

Short-segment fixation and transpedicular bone grafting for the treatment of thoracolumbar spine fracture

Purpose

Thoracolumbar fracture is one of the most common fractures of spine. And short-segment posterior fixation including the fractured vertebra (SSPFI) is usually used for the surgical treatment of it. However, the outcomes of SSPFI for different types of thoracolumbar fractures are not clear, and whether it is necessary to perform transpedicular bone grafting is still controversial. This study was conducted to determine the clinical efficacy of SSPFI for the treatment of different types of single-level thoracolumbar fracture, and make clear what kind of fractures need transpedicular bone grafting during the surgery.

Methods

Patients with single-level thoracolumbar fracture undergoing SSPFI surgery between January 2013 and June 2020 were included in this study. The operative duration, intraoperative blood loss, anterior vertebral height ratio (AVHR) and anterior vertebral height compressive ratio (AVHC) of the fractured vertebra, local kyphotic Cobb angle (LKA), vertebral wedge angle (VWA) and correction loss during follow up period were recorded. Outcomes between unilateral and bilateral pedicle screw fixation for fractured vertebra, between SSPFI with and without transpedicular bone grafting (TBG), and among different compressive degrees of fractured vertebrae were compared, respectively.

Results

A total of 161 patients were included in this study. All the patients were followed up, and the mean follow-upped duration was 25.2 ± 3.1 months (6-52 months). At the final follow-up, the AVHR was greater, and the LKA and VWA were smaller in patients with bilateral fixation (6-screw fixation) than those with unilateral fixation (5-screw fixation) of AO type A3/A4 fractures (P < 0.001). The correction loss of AVHR, LKA and VWA in fractured vertebra were significantly great when preoperative AVHC was >50% (P < 0.05). For patients with AVHC >50%, the correction loss in patients with TBG were less than those without TBG at the final follow-up (P < 0.05).

Conclusions

SSPFI using bilateral fixation was more effective than unilateral fixation in maintaining the fractured vertebral height for AO type A3/A4 fractures. For patients with AVHC >50%, the loss of correction was more obvious and it can be decreased by transpedicular bone grafting.

Pedicle screw fixation combined with posterior decompression and bone grafting for thoracolumbar spinal fractures can enhance curative effect and spinal cord function

OBJECTIVE

To explore the efficacy of pedicle screw fixation (PSF) combined with posterior decompression and bone grafting for thoracolumbar spinal fractures (TLSFs) and its influence on spinal cord function.

METHODS

In this retrospective study, 94 patients with TLSFs treated in the China-Japan Friendship Hospital rom June 2015 and September 2020 were selected, including 53 cases in the joint group treated with PSF combined with posterior decompression and bone grafting, and 41 cases in the control group with PSF alone. The two groups were compared in terms of operation time, intra-operational blood loss, length of hospital stay and wound healing as well as the pre- and post-treatment spinal cord function, and patients' clinical outcomes. Pre- and post-operatively, the pain severity was evaluated by the Visual Analogue Scale (VAS), the spinal dysfunction was assessed by Oswestry Disability Index (ODI), and the injured vertebral height and Cobb angles of the thoracolumbar spine (TLS) were compared. The clinical efficacy and postoperative complication rates of the two groups were observed and compared.

RESULTS

Less operative time, intraoperative bleeding, hospitalization time and wound healing time were determined in the joint group compared with the control group (all P<0.05). The postoperative sensory function and motor function were also better in the joint group (all P<0.05). Postoperatively, the joint group showed lower VAS and ODI scores than in the control group, with lower upper and lower TLS Cobb angles, and higher height of the anterior and posterior margins of the fractured vertebra (all P<0.05). The total effective rate was higher, and the incidence of postoperative complications was significantly lower in the joint group compared with the control group.

CONCLUSION

PSF combined with posterior decompression and bone grafting is effective in the treatment of TLSFs, which can not only significantly improve the spinal cord function and alleviate spinal dysfunction, but also help to relieve pain and reduce postoperative complications.

Effect of the intermediate pedicle screws and their insertion depth on sagittal balance and functional outcomes of lumbar fracture

OBJECTIVE

This study aimed to examine the effect of the intermediate pedicle screws and their insertion depth on sagittal balance and functional outcomes of lumbar fracture.

METHODS

This study reviewed 1,123 patients with lumbar fractures between January 2015 and June 2019, and 97 patients were ultimately enrolled in this study: Group A: 32 patients in the four-pedicle screws fixation group; Group B: 28 patients in the six-pedicle screws fixation with long intermediate pedicle screws group; Group C: 37 patients in the six-pedicle screws fixation with short intermediate pedicle screws group. The radiographic outcomes were assessed with lumbar lordosis (LL), segmental lordosis (SL), fractured vertebral lordosis (FL), sacral slope (SS), pelvic incidence (PI), and pelvic tilt (PT). The visual analog scale (VAS) and the Oswestry disability index (ODI) scores were used for assessing functional outcomes.

RESULTS

The PI, PT, and SS showed no significant differences between the three groups (P > 0.05). Compared with Group A, Groups B and C showed better FL, SL, and LL 1 month after operation (5.96 ± 1.67/4.81 ± 1.49 vs. 8.78 ± 2.90, 24.39 ± 3.80/23.70 ± 4.10 vs. 20.09 ± 3.33, 39.07 ± 3.61/39.51 ± 3.23 vs. 36.41 ± 3.11, P < 0.05) and at final follow-up (8.75 ± 1.40/6.78 ± 1.70 vs. 11.31 ± 2.61, 22.11 ± 3.39/23.70 ± 4.10 vs. 17.66 ± 2.60, 38.04 ± 3.49/39.51 ± 3.23 vs. 35.41 ± 3.11, P < 0.05). The FL of Group C were significantly better than those of Group B 1 month after operation (4.81 ± 1.49 vs. 5.96 ± 1.67, P < 0.05) and at final follow-up (6.78 ± 1.70 vs. 8.75 ± 1.40, P < 0.05). No significant differences in VAS and ODI were found between Group A and Group B (P > 0.05). There were also no significant differences in VAS and ODI between Group A and Group C (P > 0.05). However, The VAS and ODI of Group C showed better than Group B 1 month after operation (3.05 ± 0.70 vs. 3.54 ± 0.79, 17.65 ± 3.41 vs. 19.71 ± 2.35, P < 0.05) and at final follow-up (2.19 ± 0.46 vs. 2.57 ± 0.57, 13.81 ± 2.20 vs. 15.57 ± 1.73, P < 0.05).

CONCLUSIONS

Both four-pedicle screw fixation and six-pedicle screw fixation were effective in treating lumbar fracture. However, six-pedicle screw fixation with short intermediate pedicle screws showed better radiographic and functional outcomes after surgery. Therefore, we recommend six-pedicle screws fixation with short intermediate pedicle screws for the long-term recovery of sagittal balance and function.

Selection of the fusion and fixation range in the intervertebral surgery to correct thoracolumbar and lumbar tuberculosis: a retrospective clinical study

Background

To compare the diseased verses the non-diseased intervertebral surgery used in the treatment of thoracolumbar and lumbar spinal tuberculosis and to explore the best choice of fusion of fixation range.

Methods

Two hundred twenty-one patients with thoracolumbar and lumbar tuberculosis were categorized into two groups. One hundred eighteen patients underwent the diseased intervertebral surgery (lesion vertebral pedicle fixation, Group A) and 103 patients underwent the non-diseased intervertebral surgery (1 or 2 vertebral fixation above and below the affected vertebra, group B). Spinal tuberculosis diagnosis was confirmed in both groups of patients before lesion removal, bone graft fusion, and internal fixation. Clinical data and efficacy of the two surgical methods were then evaluated.

Results

The mean follow-up duration for both procedures was 65 months (50–68 months range). There were no significant differences in laboratory examinations, VAS scores, and the Cobb angle correction rate and the angle loss. However, significant differences existed in the operation time, blood loss, serosanguineous drainage volume, and blood transfusion requirement between the two groups. The diseased intervertebral surgery group performed significantly better than the non-diseased intervertebral surgery group in all of these areas. In both cases, the bone graft fused completely with the normal bone by the last follow-up, occuring at 50–86 months post surgery.

Conclusion

The diseased intervertebral surgery is a safe and feasible option for the treatment of thoracolumbar and lumbar tuberculosis. It effectively restores the physiological curvature of the spine and reduces the degeneration of adjacent vertebral bodies in the spinal column.

Different fixation pattern for thoracolumbar fracture of ankylosing spondylitis: A finite element analysis

The objective of this study is to establish an ankylosing spondylitis (AS) thoracolumbar fracture finite element (FE) model and provide a proper posterior fixation choice from the biomechanical perspective. The ankylosing spondylitis T9-L5 FE model was built and the range of motion (ROM) was compared to previous studies. The L1 transverse fracture was simulated and was separately fixed by five different patterns. The pull force and yielding force of the screws, the von Mises stress of the internal fixation, and the displacement of fracture site were analyzed to evaluate the proper fixation pattern for thoracolumbar fracture of AS. ROM of AS model was obviously restricted comparing to the normal vertebral experimental data. All the fixation patterns can stabilize the fracture. At least four levels of fixation can reduce the von Mises stress of the internal fixation. Four levels fixation has a higher pull force than the six levels fixation. Skipped level fixation did not reduce the stress, pull force and yielding force. The kyphosis correction did not change the biomechanical load. At least 4 levels fixation was needed for AS thoracolumbar fracture. The cemented screws should be chosen in 4 levels fixation to increase the holding of the screws. The skipped fixation has no advantage. The kyphosis correction can be chosen after weighing the pros and cons.

Patient-Specific Finite Element Models of Posterior Pedicle Screw Fixation: Effect of Screw's Size and Geometry

Pedicle screw fixation is extensively performed to treat spine injuries or diseases and it is common for thoracolumbar fractures. Post-operative complications may arise from this surgery leading to back pain or revisions. Finite element (FE) models could be used to predict the outcomes of surgeries but should be verified when both simplified and realistic designs of screws are used. The aim of this study was to generate patient-specific Computed Tomography (CT)-based FE models of human vertebrae with two pedicle screws, verify the models, and use them to evaluate the effect of the screws' size and geometry on the mechanical properties of the screws-vertebra structure. FE models of the lumbar vertebra implanted with two pedicle screws were created from anonymized CT-scans of three patients. Compressive loads were applied to the head of the screws. The mesh size was optimized for realistic and simplified geometry of the screws with a mesh refinement study. Finally, the optimal mesh size was used to evaluate the sensitivity of the model to changes in screw's size (diameter and length) and geometry (realistic or simplified). For both simplified and realistic models, element sizes of 0.6 mm in the screw and 1.0 mm in the bone allowed to obtain relative differences of approximately 5% or lower. Changes in screw's length resulted in 4-10% differences in maximum deflection, 1-6% differences in peak stress in the screws, 10-22% differences in mean strain in the bone around the screw; changes in screw's diameter resulted in 28-36% differences in maximum deflection, 6-27% differences in peak stress in the screws, and 30-47% differences in mean strain in the bone around the screw. The maximum deflection predicted with realistic or simplified screws correlated very well (R ² = 0.99). The peak stress in screws with realistic or simplified design correlated well (R ² = 0.82) but simplified models underestimated the peak stress. In conclusion, the results showed that the diameter of the screw has a major role on the mechanics of the screw-vertebral structure for each patient. Simplified screws can be used to estimate the mechanical properties of the implanted vertebrae, but the systematic underestimation of the peak stress should be considered when interpreting the results from the FE analyses.

Finite element analysis of wedge and biconcave deformity in four different height restoration after augmentation of osteoporotic vertebral compression fractures

Purpose

Biomechanical comparison of wedge and biconcave deformity of different height restoration after augmentation of osteoporotic vertebral compression fractures was analyzed by three-dimensional finite element analysis (FEA).

Methods

Three-dimensional finite element model (FEM) of T11-L2 segment was constructed from CT scan of elderly osteoporosis patient. The von Mises stresses of vertebrae, intervertebral disc, facet joints, displacement, and range of motion (ROM) of wedge and biconcave deformity were compared at four different heights (Genant 0–3 grade) after T12 vertebral augmentation.

Results

In wedge deformity, the stress of T12 decreased as the vertebral height in neutral position, flexion, extension, and left axial rotation, whereas increased sharply in bending at Genant 0; L1 and L2 decreased in all positions excluding flexion of L2, and T11 increased in neutral position, flexion, extension, and right axial rotation at Genant 0. No significant changes in biconcave deformity. The stress of T11-T12, T12-L1, and L1-L2 intervertebral disc gradually increased or decreased under other positions in wedge fracture, whereas L1-L2 no significant change in biconcave fracture. The utmost overall facet joint stress is at Genant 3, whereas there is no significant change under the same position in biconcave fracture. The displacement and ROM of the wedge fracture had ups and downs, while a decline in all positions excluding extension in biconcave fracture.

Conclusions

The vertebral restoration height after augmentation to Genant 0 affects the von Mises stress, displacement, and ROM in wedge deformity, which may increase the risk of fracture, whereas restored or not in biconcave deformity.

Biomechanical finite element analysis of vertebral column resection and posterior unilateral vertebral resection and reconstruction osteotomy

Background

Regarding the repair of vertebral compression fractures, there is a lack of adequate biomechanical verification as to whether only half of the vertebral body and the upper and lower intervertebral discs affect spinal biomechanics; there also remains debate as to the appropriate length of fixation.

Methods

A model of old vertebral compression fractures with kyphosis was established based on CT data. Vertebral column resection (VCR) and posterior unilateral vertebral resection and reconstruction (PUVCR) were performed at T12; long- and short-segment fixation methods were applied, and we analyzed biomechanical changes after surgery.

Results

Range of motion (ROM) decreased in all fixed models, with lumbar VCR decreasing the most and short posterior unilateral vertebral resection and reconstruction (SPUVCR) decreasing the least; in the long posterior unilateral vertebral resection and reconstruction (LPUVCR) model, the internal fixation system produced the maximum VMS stress of 213.25 mPa in a lateral bending motion and minimum stress of 40.22 mPa in a lateral bending motion in the SVCR.

Conclusion

There was little difference in thoracolumbar ROM between PUVCR and VCR models, while thoracolumbar ROM was smaller in long-segment fixation than in short-segment fixation. In all models, the VMS was most significant at the screw-rod junction and greatest at the ribcage–vertebral body interface, partly explaining the high probability of internal fixation failure and prosthesis migration in these two positions.

A finite element analysis on comparing the stability of different posterior fixation methods for thoracic total en bloc spondylectomy

Objective

To compare the spinal stability with different fixation methods after thoracic TES using finite element analysis

Methods

The spinal finite element model was established from a healthy volunteer, and the validity was verified. The models of T8 thoracic total en bloc spondylectomy (TES) with and without artificial vertebral body were established combination with different fixation methods: the first was long segment fixation with fixed segments T5–7, T9–11; the second was short segment fixation with fixed segments T6–7, T9–10; the third was modified short segment with a pair of vertebral body screws on T7 and T9 added on the basis of short segment fixation. The motions of each model in standing state were simulated in software. The range of motion (ROM) and internal fixation stress changes were analyzed.

Results

When anterior support was effective, the three fixation methods could effectively maintain the stability of the spine. However, when anterior support failed, the ROM of the long segment fixation group and the short segment fixation group in the flexion-extension directions was significantly higher than that of when the anterior support existed, while the modified short segment fixation group had no significant changes. Meanwhile, the stress of internal fixation in the long segment fixation group and the short segment fixation group were greatly increased. However, there were no significant changes in modified short segment fixation group.

Conclusion

After TES, the presence of the thoracic cage gives partial anterior stabilization. When the anterior support failed, the modified short segment fixation method can provide better stability.