An Investigation of Pressure Profiles and Wearer Comfort During Walking With a Transtibial Hydrocast Socket

Assessment of 3D printed mechanical metamaterials for prosthetic liners

This study focuses on novel design and evaluation of Elastic 50A (EL50) mechanical metamaterials with open-cell patterns for its potential application to lower limb residuum/socket interfaces, specifically that of a transtibial (TT) amputee. Mechanical characteristics, that is, effective Young's modulus (E), was tuned by altering metamaterial porosity, which was experimentally verified. Specifically, pore radius of the unit cell was varied to achieve a range of E-values (0.05-1.71 MPa) for these 3D printed metamaterials. Finite Element Analysis (FEA) was conducted to evaluate pressure distribution across key load-bearing anatomical sites of a TT residuum. Using designed metamaterials for homogeneous liners, pressure profiles were studied and compared with a silicone liner case. Additionally, a custom metamaterial liner was designed by assigning appropriate metamaterials to four load-sensitive and tolerant anatomical sites of the TT residuum. The results suggest that lowest pressure variation (PV), as a measure of pressure distribution levels and potential comfort for amputees, was achieved by the custom metamaterial liner compared to any of the homogeneous liners included in this study. It is envisaged that this work may aid future design and development of custom liners using now commonly available 3D printing technologies and available elastomer materials to maximise comfort, tissue safety and overall rehabilitation outcomes for lower limb amputees.

Scoping review to evaluate existing measurement parameters and clinical outcomes of transtibial prosthetic alignment and socket fit

INTRODUCTION

Fit and alignment are observable objectives of the prosthesis rendering process for individuals with lower limb amputation. Nevertheless, there is a dearth of validated measures to directly assess the quality of this clinical procedure.

OBJECTIVES

The objectives of this scoping review are to evaluate existing measurement parameters and clinical outcomes used in investigations of transtibial socket fit or prosthetic alignment and to identify gaps in the literature regarding tools for evaluation of prosthetic fitting.

STUDY DESIGN

Scoping literature review.

METHODS

A comprehensive search was conducted in the following databases: MEDLINE (through PubMed), Embase (through Elsevier), Scopus (through Elsevier), and Engineering Village (through Elsevier), resulting in 6107 studies to be screened.

RESULTS

Sixty-three studies were included in the review. When measuring fit, studies most frequently reported on patient-reported comfort (n = 22) and socket size compared with the residual limb volume (n = 9). Alignment was most frequently measured by the prosthetists' judgment and/or use of an alignment jig (n = 34). The measurement parameters used to determine alignment or fit varied greatly among the included studies.

CONCLUSION

This review demonstrated that most measures of socket fit rely on a patient's self-report and may vary with biopsychosocial factors unrelated to the socket fitting process. Meanwhile, alignment is determined mostly by the prosthetist's judgment, paired with objective measurements, such as alignment jigs and gait analysis. Efforts to standardize and validate measures of these parameters of prosthetic fitting are vital to improving clinical practice and reporting outcomes.

Proof of Concept for the Detection of Local Pressure Marks in Prosthesis Sockets Using Structural Dynamics Measurement

The wear comfort of a prosthesis is of great importance for amputee patients. The wear comfort can be affected by changes in the interface between the residual limb and prosthesis socket, which can be caused by time-dependent volume fluctuations of the tissue, leading to unwanted local pressure marks. The basis to ensure time-independent wear comfort of a prosthesis is to identify these changes. Common techniques for identifying these variations have a negative impact on the sensitive interface between the residual limb and prosthesis. The following paper contains a proof of concept for the detection of local pressure marks without affecting the described interface using structural dynamics measurements, exemplarily shown at a prosthetic socket for transfemoral amputees in a test bench scenario. The dynamical behaviour of the investigated system is analysed in the form of frequency response functions acquired for different pressure locations and preloads using an impact hammer for excitation and a triaxial acceleration sensor. The frequency response functions show major changes for the various boundary conditions with respect to their frequency-dependent compositions. The results demonstrate how the utilised method enables the identification of changes in local pressure marks regarding the variation of position and magnitude.

Lower limb prosthetic interfaces: Clinical and technological advancement and potential future direction

The human-prosthesis interface is one of the most complicated challenges facing the field of prosthetics, despite substantive investments in research and development by researchers and clinicians around the world. The journal of the International Society for Prosthetics and Orthotics, Prosthetics and Orthotics International, has contributed substantively to the growing body of knowledge on this topic. In celebrating the 50th anniversary of the International Society for Prosthetics and Orthotics, this narrative review aims to explore how human-prosthesis interfaces have changed over the last five decades; how research has contributed to an understanding of interface mechanics; how clinical practice has been informed as a result; and what might be potential future directions. Studies reporting on comparison, design, manufacturing and evaluation of lower limb prosthetic sockets, and osseointegration were considered. This review demonstrates that, over the last 50 years, clinical research has improved our understanding of socket designs and their effects; however, high-quality research is still needed. In particular, there have been advances in the development of volume and thermal control mechanisms with a few designs having the potential for clinical application. Similarly, advances in sensing technology, soft tissue quantification techniques, computing technology, and additive manufacturing are moving towards enabling automated, data-driven manufacturing of sockets. In people who are unable to use a prosthetic socket, osseointegration provides a functional solution not available 50 years ago. Furthermore, osseointegration has the potential to facilitate neuromuscular integration. Despite these advances, further improvement in mechanical features of implants, and infection control and prevention are needed.