A Three-Dimensional Study of Midfacial Changes Following Le Fort II Distraction With Zygomatic Repositioning in Syndromic Patients:

Integrating Virtual Surgical Planning and 3D-Printed Tools with Iliac Bone Grafts for Orbital and Zygomatic Reconstruction in Hemifacial Microsomia Patients

Hemifacial Microsomia (HFM) is the second most common congenital craniofacial malformation syndrome, and the complexity of HFM makes its treatment challenging. The present study aimed to introduce a new approach of utilization of virtual surgical planning (VSP) and 3D-printed surgical adjuncts for maxillofacial reconstruction. Five HFM patients were included in this study. All participants were provided with a full VSP, including the design of osteotomy lines, the design and fabrication of 3D-printed cutting guides, fixation plates, and titanium mesh for implantation. With the assistance of 3D-printed cutting guides and fixation plates, the orbital deformities were corrected, and a 3D-printed titanium mesh combined with iliac cancellous bone graft was applied to reconstruct the zygomatic arch. The surgical accuracy, effectiveness, and bone absorption rate were evaluated. All patients completed the entirely digital treatment process without experiencing severe complications. The surgical adjuncts were effective in aligning the movement of the bone segments with the surgical plan, resulting in mean 3D deviations (1.0681 ± 0.15 mm) and maximum 3D deviations (3.1127 ± 0.44 mm). The image fusion results showed that the patients' postoperative position of the maxilla, zygoma, and orbital rim was consistent with the virtual surgical plan, with only a slight increase in the area of bone grafting. The postoperative measurements showed significant improvement in the asymmetry indices of Er (AI of Er: from 17.91 ± 3.732 to 5.427 ± 1.389 mm, p = 0.0001) and FZ (AI of FZ: from 7.581 ± 1.435 to 4.070 ± 1.028 mm, p = 0.0009) points. In addition, the observed bone resorption rate at the 6-month follow-up across the five patients was 45.24% ± 3.13%. In conclusion, the application of VSP and 3D-printed surgical adjuncts demonstrates significant value in enhancing the precision and effectiveness of surgical treatments for HFM. A 3D-printed titanium mesh combined with iliac cancellous bone graft can be considered an ideal alternative for the reconstruction of the zygomatic arch.

Integration and Application of Multimodal Measurement Techniques: Relevance of Photogrammetry to Orthodontics

Multimodal imaging, including 3D modalities, is increasingly being applied in orthodontics, both as a diagnostic tool and especially for the design of intraoral appliances, where geometric accuracy is very important. Laser scanners and other precision 3D-imaging devices are expensive and cumbersome, which limits their use in medical practice. Photogrammetry, using ordinary 2D photographs or video recordings to create 3D imagery, offers a cheaper and more convenient alternative, replacing the specialised equipment with handy consumer cameras. The present study addresses the question of to what extent, and under what conditions, this technique can be an adequate replacement for the 3D scanner. The accuracy of simple surface reconstruction and of model embedding achieved with photogrammetry was verified against that obtained with a triangulating laser scanner. To roughly evaluate the impact of image imperfections on photogrammetric reconstruction, the photographs for photogrammetry were taken under various lighting conditions and were used either raw or with a blur-simulating defocus. Video footage was also tested as another 2D-imaging modality feeding data into photogrammetry. The results show the significant potential of photogrammetric techniques.

Le Fort II Distraction with Simultaneous Zygomatic Repositioning

Severe midface hypoplasia is often managed by Le Fort III distraction. Le Fort II distraction with zygomatic repositioning is a modification of the Le Fort III distraction operation aimed to correct abnormal facial ratios of patients with greater central than lateral midface deficiency. The operation starts with Le Fort III osteotomies and is followed by separation and fixation of bilateral zygomas. The central nasomaxillary Le Fort II segment is then distracted to achieve independent movements of the central and lateral midface. The Le Fort II zygomatic repositioning operation has become our procedure of choice for patients with Apert facial dysmorphology.