The leading-edge vortex on a rotating wing changes markedly beyond a certain central body size

Research on Deployable Wings for MAVs Bioinspired by the Hind Wings of the Beetle Protaetia brevitarsis

Deployable hind wings of beetles led to a bio-inspired idea to design deployable micro aerial vehicles (MAVs) to meet the requirement of miniaturization. In this paper, a bionic deployable wing (BD-W) model is designed based on the folding mechanism and elliptical wing vein structure of the Protaetia brevitarsis hindwing, and its structural static and aerodynamic characteristics are analyzed by using ANSYS Workbench. Finally, the 3D-printed bionic deployable wing was tested in a wind tunnel and compared with simulation experiments to explore the effects of different incoming velocity, flapping frequency, and angle of attack on its aerodynamic characteristics, which resulted in the optimal combination of the tested parameters, among which, the incoming velocity is 3 m/s, the flapping frequency is 10 Hz, the angle of attack is 15°, and the lift-to-drag ratio of this parameter combination is 4.91. The results provide a theoretical basis and technical reference for the further development of bionic flapping wing for MAV applications.

Performance of passively pitching flapping wings in the presence of vertical inflows

The successful implementation of passively pitching flapping wings strongly depends on their ability to operate efficiently in wind disturbances. In this study, we experimentally investigated the interaction between a uniform vertical inflow perturbation and a passive-pitching flapping wing using a Reynolds-scaled apparatus operating in water at Reynolds number ≈3600. A parametric study was performed by systematically varying the Cauchy number (Ch) of the wings from 0.09 to 11.52. The overall lift and drag, and pitch angle of the wing were measured by varying the magnitude of perturbation fromJ_Vert= -0.6 (downward inflow) toJ_Vert= 0.6 (upward inflow) at eachCh, whereJ_Vertis the ratio of the inflow velocity to the wing's velocity. We found that the lift and drag had remarkably different characteristics in response to bothChandJ_Vert. Across allCh, while mean lift tended to increase as the inflow perturbation varied from -0.6 to 0.6, drag was significantly less sensitive to the perturbation. However effect of the vertical inflow on drag was dependent onCh, where it tended to vary from an increasing to a decreasing trend asChwas changed from 0.09 to 11.52. The differences in the lift and drag with perturbation magnitude could be attributed to the reorientation of the net force over the wing as a result of the interaction with the perturbation. These results highlight the complex interactions between passively pitching flapping wings and freestream perturbations and will guide the design of miniature flying crafts with such architectures.

Effects of uniform vertical inflow perturbations on the performance of flapping wings

Flapping wings have attracted significant interest for use in miniature unmanned flying vehicles. Although numerous studies have investigated the performance of flapping wings under quiescent conditions, effects of freestream disturbances on their performance remain under-explored. In this study, we experimentally investigated the effects of uniform vertical inflows on flapping wings using a Reynolds-scaled apparatus operating in water at Reynolds number ≈ 3600. The overall lift and drag produced by a flapping wing were measured by varying the magnitude of inflow perturbation from J Vert = -1 (downward inflow) to J Vert = 1 (upward inflow), where J Vert is the ratio of the inflow velocity to the wing's velocity. The interaction between flapping wing and downward-oriented inflows resulted in a steady linear reduction in mean lift and drag coefficients,C ¯ L andC ¯ D , with increasing inflow magnitude. While a steady linear increase inC ¯ L andC ¯ D was noted for upward-oriented inflows between 0 < J Vert < 0.3 and J Vert > 0.7, a significant unsteady wing-wake interaction occurred when 0.3 ≤ J Vert < 0.7, which caused large variations in instantaneous forces over the wing and led to a reduction in mean performance. These findings highlight asymmetrical effects of vertically oriented perturbations on the performance of flapping wings and pave the way for development of suitable control strategies.

Data-driven CFD Scaling of Bioinspired Mars Flight Vehicles for Hover

One way to improve our model of Mars is through aerial sampling and surveillance, which could provide information to augment the observations made by ground-based exploration and satellite imagery. Flight in the challenging ultra-low-density Martian environment can be achieved with properly scaled bioinspired flapping wing vehicle configurations that utilize the same high lift producing mechanisms that are employed by insects on Earth. Through dynamic scaling of wings and kinematics, we investigate the ability to generate solutions for a broad range of flapping wing flight vehicles masses ranging from insects O(10-3) kg to the Mars helicopter Ingenuity O(100) kg. A scaling method based on a neural-network trained on 3D Navier-Stokes solutions is proposed to determine approximate wing size and kinematic values that generate bioinspired hover solutions. We demonstrate that a family of solutions exists for designs that range from 1 to 1000 grams, which are verified and examined using a 3D Navier-Stokes solver. Our results reveal that unsteady lift enhancement mechanisms, such as delayed stall and rotational lift, are present in the bioinspired solutions for the scaled vehicles hovering in Martian conditions. These hovering vehicles exhibit payloads of up to 1 kg and flight times on the order of 100 minutes when considering the respective limiting cases of the vehicle mass being comprised entirely of payload or entirely of a battery and neglecting any transmission inefficiencies. This method can help to develop a range of Martian flying vehicle designs with mission viable payloads, range, and endurance.

Aerodynamic performance of flexible flapping wings deformed by slack angle

Wing flexibility is unavoidable for flapping wing flyers to ensure a lightweight body and for higher payload allowances on board. It also effectively minimizes the inertia force from high-frequency wingbeat motion. However, related studies that attempt to clarify the essence of wing flexibility remain insufficient. Here, a parametric study of a flexible wing was conducted as part of the effort to build an aerodynamic model and analyze its aerodynamic performance. The quasi-steady modeling was adopted with experimentally determined translational forces. These forces were determined from 84 flexible wing cases while varying the angle of attack at the wing rootα_rand the flexibility parameter, slack angleθ_S, with 19 additional rigid wing cases. This study foundα_rfor optimum lift generation to exceed 45° irrespective ofθ_S. The coefficient curves were well-fitted with a cubed-sine function. The model was rigorously validated with various wing kinematics, giving a good estimation of the experimental results. The estimated error was less than 5%, 6%, and 8% for the lift, drag, and moment, respectively, considering fast to moderate wing kinematics. The study was extended to analyze the pure aerodynamic performance of the flexible wing. The most suitable wing for a flapping-wing micro-aerial vehicle wing design with a simple vein structure was found to be the 5° slack-angled wing. The inference from this study further shows that a small amount of deformation is needed to increase the lift, as observed in natural flyers. Thus, wing deformation could allow living flyers to undertake less pitching motion in order to reduce the mechanical power and increase the efficiency of their wings.