Role of interfacial adhesion on minimum wear particle size and roughness evolution

Roughness Evolution Induced by Third-Body Wear

Surface roughness is a key factor when it comes to friction and wear, as well as to other physical properties. These phenomena are controlled by mechanisms acting at small scales, in which the topography of apparently flat surfaces is revealed. Roughness in natural surfaces has been reported to conform to self-affine statistics in a wide variety of settings (ranging from earthquake physics to micro-electro-mechanical devices), meaning that the height profile can be described using a spectrum where the amplitude is proportional to its wavelength raised to a constant power, which is related to a statistical parameter named Hurst exponent. We analyze the roughness evolution in atomistic surfaces during molecular dynamics simulations of wear. Both pairs of initially flat and initially rough surfaces in contact are worn by a third body formed by particles trapped between them during relative sliding. During the first sliding stages, the particles trapped between the first bodies scratch the surfaces. Once the former becomes coated with atoms from the latter, the wear process slows down and becomes "adhesive like." The initial particle sizes are consistent with the minimum size to be expected for the debris, but tend to grow by material removal from the surfaces and to agglomerate. We show that, for the particular configurations under consideration, the surface roughness seems to converge to a steady state characterized by Hurst exponent close to 0.8, independently of the initial conditions.

Supplementary Information

The online version contains supplementary material available at 10.1007/s11249-024-01833-9.

The Correlation of Surface Roughness Parameters of Zirconia and Lithium Disilicate with Steatite Wear

PURPOSE

Various surface roughness parameters are utilized to describe the surface in the tooth to ceramics abrasion and to assess the resulting wear. The use of three-dimensional parameters may offer a better estimation for wear and an improved deduced clinical surface treatment. The aim of this study was to determine the influence of various surface roughness parameters of zirconia and lithium disilicate ceramics on the wear of steatite antagonists.

MATERIAL AND METHODS

Forty zirconia specimens with a diameter of 7 mm and a thickness of 3 mm and 40 lithium disilicate specimens with the dimensions 10×10×4 mm were each divided into five subgroups. Two subgroups were treated with different clinically established diamond burs; a third subgroup was treated with a silicone polishing set. Two additional subgroups were produced by glazing the surfaces after treatment. Surface roughness parameters were determined by laser scanning microscopy. All specimens underwent 1.2 million loading cycles using steatite antagonists. After regular intervals of cycles, precision impressions were made to assess the wear. The correlation between wear and different roughness parameters was evaluated using the Spearman correlation test.

RESULTS

For the glazed zirconia, unglazed zirconia, and glazed lithium disilicate specimens no significant correlations (p > 0.05) between the investigated roughness parameters and antagonist wear could be found. In the unglazed lithium disilicate groups, significant (p ≤ 0.05) correlations with steatite substance loss could be found for several roughness parameters after 1.2 million cycles.

CONCLUSIONS

For lithium disilicate, it seems not sufficient to use only one roughness parameter to indicate the wear behavior of the surface. There was no correlation between wear and the tested roughness parameters of zirconia surfaces.

Modeling Adhesive Wear in Asperity and Rough Surface Contacts: A Review

Wear is one of the most fundamental topics in tribology and adhesive wear is argued as the least avoidable wear type. Numerical techniques have allowed advances in more realistic simulations of adhesive wear mechanisms and promoted our understanding of it. This paper reviews the classic work on wear modeling by Archard and Rabinowicz, followed by a comprehensive summary of the adhesive wear numerical models and techniques based on physical parameters. The studies on wear mechanisms at the asperity level and rough surfaces are separately presented. Different models and their key findings are presented according to the method type. The advantages and deficiencies of these models are stated and future work, such as considering more realistic geometries and material properties for adhesive wear modeling, is suggested.

A review of advances in tribology in 2020–2021

Around 1,000 peer-reviewed papers were selected from 3,450 articles published during 2020–2021, and reviewed as the representative advances in tribology research worldwide. The survey highlights the development in lubrication, wear and surface engineering, biotribology, high temperature tribology, and computational tribology, providing a show window of the achievements of recent fundamental and application researches in the field of tribology.