1
|
Xie C, Wan C, Wang Y, Song J, Wu D, Li Y. Effects of Pulse Transit Time and Pulse Arrival Time on Cuff-less Blood Pressure Estimation: A Comparison Study with Multiple Experimental Interventions. ANNUAL INTERNATIONAL CONFERENCE OF THE IEEE ENGINEERING IN MEDICINE AND BIOLOGY SOCIETY. IEEE ENGINEERING IN MEDICINE AND BIOLOGY SOCIETY. ANNUAL INTERNATIONAL CONFERENCE 2023; 2023:1-4. [PMID: 38083296 DOI: 10.1109/embc40787.2023.10340548] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 12/18/2023]
Abstract
Pulse transit time (PTT) has shown a correlation with blood pressure (BP), and it is considered as a potential marker for cuff-less BP estimation. However, pulse arrival time (PAT) including pre-ejection period (PEP) has been utilized more widely because of its convenience to acquisition and calculation. In spite of this, whether PAT can surrogate PTT has been a controversial topic for many years. In this study, we designed an experiment on 55 subjects with multiple interventions, those may cause the changes in BP and PEP. We analyzed the linear and nonlinear correlations between BP and PTT/PAT, and also assessed the performances of PTT-based and PAT-based models on tracking the BP variation. Five typical BP estimation models were used for comparison. We found that PEP could change rapidly in response to the interventions related with physical stress. Although PTT had a better linear correlation with BP, most of the PAT-based models showed more accuracy than PTT-based models in all of the interventions, especially for the calibrated models. It is suggested that PAT has the potential to predict BP, and the inclusion of PEP in the measurement of PAT is necessary.
Collapse
|
2
|
Seo Y, Kwon S, Sunarya U, Park S, Park K, Jung D, Cho Y, Park C. Blood pressure estimation and its recalibration assessment using wrist cuff blood pressure monitor. Biomed Eng Lett 2023; 13:221-233. [PMID: 37124108 PMCID: PMC10130301 DOI: 10.1007/s13534-023-00271-1] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 10/20/2022] [Revised: 01/02/2023] [Accepted: 02/16/2023] [Indexed: 05/02/2023] Open
Abstract
The rapid evolution of wearable technology in healthcare sectors has created the opportunity for people to measure their blood pressure (BP) using a smartwatch at any time during their daily activities. Several commercially-available wearable devices have recently been equipped with a BP monitoring feature. However, concerns about recalibration remain. Pulse transit time (PTT)-based estimation is required for initial calibration, followed by periodic recalibration. Recalibration using arm-cuff BP monitors is not practical during everyday activities. In this study, we investigated recalibration using PTT-based BP monitoring aided by a deep neural network (DNN) and validated the performance achieved with more practical wrist-cuff BP monitors. The PTT-based prediction produced a mean absolute error (MAE) of 4.746 ± 1.529 mmHg for systolic blood pressure (SBP) and 3.448 ± 0.608 mmHg for diastolic blood pressure (DBP) when tested with an arm-cuff monitor employing recalibration. Recalibration clearly improved the performance of both DNN and conventional linear regression approaches. We established that the periodic recalibration performed by a wrist-worn BP monitor could be as accurate as that obtained with an arm-worn monitor, confirming the suitability of wrist-worn devices for everyday use. This is the first study to establish the potential of wrist-cuff BP monitors as a means to calibrate BP monitoring devices that can reliably substitute for arm-cuff BP monitors. With the use of wrist-cuff BP monitoring devices, continuous BP estimation, as well as frequent calibrations to ensure accurate BP monitoring, are now feasible.
Collapse
Affiliation(s)
- Youjung Seo
- Department of Computer Engineering, Kwangwoon University, Seoul, 01897 Korea
| | - Saehim Kwon
- Department of Artificial Intelligence, Kwangwoon University, Seoul, 01897 Korea
| | - Unang Sunarya
- Department of Computer Engineering, Kwangwoon University, Seoul, 01897 Korea
- School of Applied Science, Telkom University, Bandung, 40257 Indonesia
| | - Sungmin Park
- Department of Convergence IT Engineering and the Department of Electrical Engineering, Pohang University of Science and Technology, Pohang, 37673 Korea
| | - Kwangsuk Park
- Department of Biomedical Engineering, College of Medicine, Seoul National University, Seoul, 03080 Korea
| | - Dawoon Jung
- Center for Artificial Intelligence, Korea Institute of Science and Technology, Seoul, 13916 Korea
| | - Youngho Cho
- Department of Electrical and Communication Engineering, University of Daelim, Anyang, 13916 Korea
| | - Cheolsoo Park
- Department of Computer Engineering, Kwangwoon University, Seoul, 01897 Korea
| |
Collapse
|
3
|
Lee S, Joshi GP, Son CH, Lee G. Combining Gaussian Process with Hybrid Optimal Feature Decision in Cuffless Blood Pressure Estimation. Diagnostics (Basel) 2023; 13:diagnostics13040736. [PMID: 36832226 PMCID: PMC9955403 DOI: 10.3390/diagnostics13040736] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 12/18/2022] [Revised: 02/06/2023] [Accepted: 02/08/2023] [Indexed: 02/17/2023] Open
Abstract
Noninvasive blood pressure estimation is crucial for cardiovascular and hypertension patients. Cuffless-based blood pressure estimation has received much attention recently for continuous blood pressure monitoring. This paper proposes a new methodology that combines the Gaussian process with hybrid optimal feature decision (HOFD) in cuffless blood pressure estimation. First, we can choose one of the feature selection methods: robust neighbor component analysis (RNCA), minimum redundancy, maximum relevance (MRMR), and F-test, based on the proposed hybrid optimal feature decision. After that, a filter-based RNCA algorithm uses the training dataset to obtain weighted functions by minimizing the loss function. Next, we combine the Gaussian process (GP) algorithm as the evaluation criteria, which is used to determine the best feature subset. Hence, combining GP with HOFD leads to an effective feature selection process. The proposed combining Gaussian process with the RNCA algorithm shows that the root mean square errors (RMSEs) for the SBP (10.75 mmHg) and DBP (8.02 mmHg) are lower than those of the conventional algorithms. The experimental results represent that the proposed algorithm is very effective.
Collapse
Affiliation(s)
- Soojeong Lee
- Department of Computer Engineering, Sejong University, 209 Neungdong-ro, Gwangjin-gu, Seoul 05006, Republic of Korea
| | - Gyanendra Prasad Joshi
- Department of Computer Engineering, Sejong University, 209 Neungdong-ro, Gwangjin-gu, Seoul 05006, Republic of Korea
| | - Chang-Hwan Son
- Department of Software Science & Engineering, Kunsan National University, 558 Daehak-ro, Gunsan-si 54150, Republic of Korea
- Correspondence: (C.-H.S.); (G.L.)
| | - Gangseong Lee
- Ingenium College, Kwangwoon University, 20 Kwangwoon-ro, Nowon-gu, Seoul 01897, Republic of Korea
- Correspondence: (C.-H.S.); (G.L.)
| |
Collapse
|
4
|
Long-term stability of over-the-counter cuffless blood pressure monitors: a proposal. HEALTH AND TECHNOLOGY 2023; 13:53-63. [PMID: 36713070 PMCID: PMC9870659 DOI: 10.1007/s12553-023-00726-6] [Citation(s) in RCA: 1] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 02/14/2022] [Revised: 10/17/2022] [Accepted: 01/04/2023] [Indexed: 01/25/2023]
Abstract
Blood pressure is an important cardiovascular parameter. Currently, the cuff-based sphygmomanometer is a popular, reliable, measurement method, but blood pressure monitors without cuffs have become popular and are now available without a prescription. Blood pressure monitors must be approved by regulatory authorities. Current cuffless blood pressure (CL-BP) monitors are not suitable for at-home management and prevention of hypertension. This paper proposes simple criteria for over-the-counter CL-BP monitoring. First, the history of the sphygmomanometer and current standard blood pressure protocol are reviewed. The main components of CL-BP monitoring are accuracy during the resting condition, accuracy during dynamic blood pressure changes, and long-term stability. In this proposal we recommend intermittent measurement to ensure that active measurement accuracy mirrors resting condition accuracy. A new experimental protocol is proposed to maintain long-term stability. A medically approved automated sphygmomanometer was used as the standard device in this study. The long-term accuracy of the test device is based on the definition of propagation error, i.e., for an oscillometric automated sphygmomanometer (5 ± 8 mmHg) ± the error for the test device static accuracy (-0.12 ± 5.49 mmHg for systolic blood pressure and - 1.17 ± 5.06 mmHg for diastolic blood pressure). Thus, the long-term stabilities were - 3.38 ± 7.1 mmHg and - 1.38 ± 5.4 mmHg, which satisfied propagation error. Further research and discussion are necessary to create standards for use by manufacturers; such standards should be readily evaluated and ensure high-quality evidence. Supplementary information The online version contains supplementary material available at 10.1007/s12553-023-00726-6.
Collapse
|
5
|
Zabihi S, Rahimian E, Marefat F, Asif A, Mohseni P, Mohammadi A. BP-Net: Cuff-less and non-invasive blood pressure estimation via a generic deep convolutional architecture. Biomed Signal Process Control 2022. [DOI: 10.1016/j.bspc.2022.103850] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/02/2022]
|
6
|
Ismail SNA, Nayan NA, Jaafar R, May Z. Recent Advances in Non-Invasive Blood Pressure Monitoring and Prediction Using a Machine Learning Approach. SENSORS (BASEL, SWITZERLAND) 2022; 22:6195. [PMID: 36015956 PMCID: PMC9412312 DOI: 10.3390/s22166195] [Citation(s) in RCA: 8] [Impact Index Per Article: 4.0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Grants] [Track Full Text] [Figures] [Subscribe] [Scholar Register] [Received: 06/14/2022] [Revised: 07/25/2022] [Accepted: 08/04/2022] [Indexed: 06/15/2023]
Abstract
Blood pressure (BP) monitoring can be performed either invasively via arterial catheterization or non-invasively through a cuff sphygmomanometer. However, for conscious individuals, traditional cuff-based BP monitoring devices are often uncomfortable, intermittent, and impractical for frequent measurements. Continuous and non-invasive BP (NIBP) monitoring is currently gaining attention in the human health monitoring area due to its promising potentials in assessing the health status of an individual, enabled by machine learning (ML), for various purposes such as early prediction of disease and intervention treatment. This review presents the development of a non-invasive BP measuring tool called sphygmomanometer in brief, summarizes state-of-the-art NIBP sensors, and identifies extended works on continuous NIBP monitoring using commercial devices. Moreover, the NIBP predictive techniques including pulse arrival time, pulse transit time, pulse wave velocity, and ML are elaborated on the basis of bio-signals acquisition from these sensors. Additionally, the different BP values (systolic BP, diastolic BP, mean arterial pressure) of the various ML models adopted in several reported studies are compared in terms of the international validation standards developed by the Advancement of Medical Instrumentation (AAMI) and the British Hypertension Society (BHS) for clinically-approved BP monitors. Finally, several challenges and possible solutions for the implementation and realization of continuous NIBP technology are addressed.
Collapse
Affiliation(s)
- Siti Nor Ashikin Ismail
- Department of Electrical, Electronic and Systems Engineering, Universiti Kebangsaan Malaysia, UKM Bangi 43600, Selangor, Malaysia
| | - Nazrul Anuar Nayan
- Department of Electrical, Electronic and Systems Engineering, Universiti Kebangsaan Malaysia, UKM Bangi 43600, Selangor, Malaysia
- Institute Islam Hadhari, Universiti Kebangsaan Malaysia, UKM Bangi 43600, Selangor, Malaysia
| | - Rosmina Jaafar
- Department of Electrical, Electronic and Systems Engineering, Universiti Kebangsaan Malaysia, UKM Bangi 43600, Selangor, Malaysia
| | - Zazilah May
- Department of Electrical, Electronic and Systems Engineering, Universiti Kebangsaan Malaysia, UKM Bangi 43600, Selangor, Malaysia
- Electrical and Electronic Engineering Department, Universiti Teknologi Petronas, Seri Iskandar 32610, Perak, Malaysia
| |
Collapse
|
7
|
He J, Ou J, He A, Shu L, Liu T, Qu R, Xu X, Chen Z, Yan Y. A new approach for daily life Blood-Pressure estimation using smart watch. Biomed Signal Process Control 2022. [DOI: 10.1016/j.bspc.2022.103616] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.5] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/28/2022]
|
8
|
Treebupachatsakul T, Boosamalee A, Shinnakerdchoke S, Pechprasarn S, Thongpance N. Cuff-Less Blood Pressure Prediction from ECG and PPG Signals Using Fourier Transformation and Amplitude Randomization Preprocessing for Context Aggregation Network Training. BIOSENSORS 2022; 12:159. [PMID: 35323429 PMCID: PMC8946486 DOI: 10.3390/bios12030159] [Citation(s) in RCA: 3] [Impact Index Per Article: 1.5] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Figures] [Subscribe] [Scholar Register] [Received: 01/18/2022] [Revised: 02/25/2022] [Accepted: 02/28/2022] [Indexed: 06/14/2023]
Abstract
This research proposes an algorithm to preprocess photoplethysmography (PPG) and electrocardiogram (ECG) signals and apply the processed signals to the context aggregation network-based deep learning to achieve higher accuracy of continuous systolic and diastolic blood pressure monitoring than other reported algorithms. The preprocessing method consists of the following steps: (1) acquiring the PPG and ECG signals for a two second window at a sampling rate of 125 Hz; (2) separating the signals into an array of 250 data points corresponding to a 2 s data window; (3) randomizing the amplitude of the PPG and ECG signals by multiplying the 2 s frames by a random amplitude constant to ensure that the neural network can only learn from the frequency information accommodating the signal fluctuation due to instrument attachment and installation; (4) Fourier transforming the windowed PPG and ECG signals obtaining both amplitude and phase data; (5) normalizing both the amplitude and the phase of PPG and ECG signals using z-score normalization; and (6) training the neural network using four input channels (the amplitude and the phase of PPG and the amplitude and the phase of ECG), and arterial blood pressure signal in time-domain as the label for supervised learning. As a result, the network can achieve a high continuous blood pressure monitoring accuracy, with the systolic blood pressure root mean square error of 7 mmHg and the diastolic root mean square error of 6 mmHg. These values are within the error range reported in the literature. Note that other methods rely only on mathematical models for the systolic and diastolic values, whereas the proposed method can predict the continuous signal without degrading the measurement performance and relying on a mathematical model.
Collapse
Affiliation(s)
- Treesukon Treebupachatsakul
- Department of Biomedical Engineering, School of Engineering, King Mongkut’s Institute of Technology Ladkrabang, Bangkok 10520, Thailand; (T.T.); (A.B.); (S.S.)
| | - Apivitch Boosamalee
- Department of Biomedical Engineering, School of Engineering, King Mongkut’s Institute of Technology Ladkrabang, Bangkok 10520, Thailand; (T.T.); (A.B.); (S.S.)
| | - Siratchakrit Shinnakerdchoke
- Department of Biomedical Engineering, School of Engineering, King Mongkut’s Institute of Technology Ladkrabang, Bangkok 10520, Thailand; (T.T.); (A.B.); (S.S.)
| | - Suejit Pechprasarn
- College of Biomedical Engineering, Rangsit University, Pathum Thani 12000, Thailand;
| | - Nuntachai Thongpance
- College of Biomedical Engineering, Rangsit University, Pathum Thani 12000, Thailand;
| |
Collapse
|
9
|
Kido K, Chen Z, Huang M, Tamura T, Chen W, Ono N, Takeuchi M, Altaf-Ul-Amin M, Kanaya S. Discussion of Cuffless Blood Pressure Prediction Using Plethysmograph Based on a Longitudinal Experiment: Is the Individual Model Necessary? Life (Basel) 2021; 12:life12010011. [PMID: 35054404 PMCID: PMC8780350 DOI: 10.3390/life12010011] [Citation(s) in RCA: 8] [Impact Index Per Article: 2.7] [Reference Citation Analysis] [Abstract] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 11/17/2021] [Revised: 12/17/2021] [Accepted: 12/18/2021] [Indexed: 11/20/2022] Open
Abstract
Using the Plethysmograph (PPG) signal to estimate blood pressure (BP) is attractive given the convenience and possibility of continuous measurement. However, due to the personal differences and the insufficiency of data, the dilemma between the accuracy for a small dataset and the robustness as a general method remains. To this end, we scrutinized the whole pipeline from the feature selection to regression model construction based on a one-month experiment with 11 subjects. By constructing the explanatory features consisting of five general PPG waveform features that do not require the identification of dicrotic notch and diastolic peak and the heart rate, three regression models, which are partial least square, local weighted partial least square, and Gaussian Process model, were built to reflect the underlying assumption about the nature of the fitting problem. By comparing the regression models, it can be confirmed that an individual Gaussian Process model attains the best results with 5.1 mmHg and 4.6 mmHg mean absolute error for SBP and DBP and 6.2 mmHg and 5.4 mmHg standard deviation for SBP and DBP. Moreover, the results of the individual models are significantly better than the generalized model built with the data of all subjects.
Collapse
Affiliation(s)
- Koshiro Kido
- Graduate School of Science and Technology, Nara Institute of Science and Technology, Ikoma 630-0192, Japan; (K.K.); (Z.C.); (N.O.); (M.A.-U.-A.); (S.K.)
| | - Zheng Chen
- Graduate School of Science and Technology, Nara Institute of Science and Technology, Ikoma 630-0192, Japan; (K.K.); (Z.C.); (N.O.); (M.A.-U.-A.); (S.K.)
| | - Ming Huang
- Graduate School of Science and Technology, Nara Institute of Science and Technology, Ikoma 630-0192, Japan; (K.K.); (Z.C.); (N.O.); (M.A.-U.-A.); (S.K.)
- Correspondence: ; Tel.: +81-743-72-5321
| | - Toshiyo Tamura
- Institute for Healthcare Robotics, Waseda University, Tokyo 162-0041, Japan;
| | - Wei Chen
- Department of Electronic Engineering, School of Information Science and Technology, Fudan University, Shanghai 201203, China;
| | - Naoaki Ono
- Graduate School of Science and Technology, Nara Institute of Science and Technology, Ikoma 630-0192, Japan; (K.K.); (Z.C.); (N.O.); (M.A.-U.-A.); (S.K.)
- Data Science Center, Nara Institute of Science and Technology, Ikoma 630-0192, Japan
| | | | - Md. Altaf-Ul-Amin
- Graduate School of Science and Technology, Nara Institute of Science and Technology, Ikoma 630-0192, Japan; (K.K.); (Z.C.); (N.O.); (M.A.-U.-A.); (S.K.)
| | - Shigehiko Kanaya
- Graduate School of Science and Technology, Nara Institute of Science and Technology, Ikoma 630-0192, Japan; (K.K.); (Z.C.); (N.O.); (M.A.-U.-A.); (S.K.)
- Data Science Center, Nara Institute of Science and Technology, Ikoma 630-0192, Japan
| |
Collapse
|
10
|
Landry C, Hedge ET, Hughson RL, Peterson SD, Arami A. Accurate Blood Pressure Estimation During Activities of Daily Living: A Wearable Cuffless Solution. IEEE J Biomed Health Inform 2021; 25:2510-2520. [PMID: 33497346 DOI: 10.1109/jbhi.2021.3054597] [Citation(s) in RCA: 14] [Impact Index Per Article: 4.7] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/06/2022]
Abstract
The objective is to develop a cuffless method that accurately estimates blood pressure (BP) during activities of daily living. User-specific nonlinear autoregressive models with exogenous inputs (NARX) are implemented using artificial neural networks to estimate the BP waveforms from electrocardiography and photoplethysmography signals. To broaden the range of BP in the training data, subjects followed a short procedure consisting of sitting, standing, walking, Valsalva maneuvers, and static handgrip exercises. The procedure was performed before and after a six-hour testing phase wherein five participants went about their normal daily living activities. Data were further collected at a four-month time point for two participants and again at six months for one of the two. The performance of three different NARX models was compared with three pulse arrival time (PAT) models. The NARX models demonstrate superior accuracy and correlation with "ground truth" systolic and diastolic BP measures compared to the PAT models and a clear advantage in estimating the large range of BP. Preliminary results show that the NARX models can accurately estimate BP even months apart from the training. Preliminary testing suggests that it is robust against variabilities due to sensor placement. This establishes a method for cuffless BP estimation during activities of daily living that can be used for continuous monitoring and acute hypotension and hypertension detection.
Collapse
|
11
|
Yang S, Sohn J, Lee S, Lee J, Kim HC. Estimation and Validation of Arterial Blood Pressure Using Photoplethysmogram Morphology Features in Conjunction With Pulse Arrival Time in Large Open Databases. IEEE J Biomed Health Inform 2021; 25:1018-1030. [PMID: 32750963 DOI: 10.1109/jbhi.2020.3009658] [Citation(s) in RCA: 19] [Impact Index Per Article: 6.3] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/05/2022]
Abstract
Although various predictors and methods for BP estimation have been proposed, differences in study designs have led to difficulties in determining the optimal method. This study presents analyses of BP estimation methods using 2.4 million cardiac cycles of two commonly used non-invasive biosignals, electrocardiogram (ECG) and photoplethysmogram (PPG), from 1376 surgical patients. Feature selection methods were used to determine the best subset of predictors from a total of 42 including PAT, heart rate (HR), and various PPG morphology features, and BP estimation models constructed using linear regression (LR), random forest (RF), artificial neural network (ANN), and recurrent neural network (RNN) were evaluated. 28 features out of 42 were determined as suitable for BP estimation, in particular two PPG morphology features outperformed PAT, which has been conventionally seen as the best non-invasive indicator of BP. By modelling the low frequency component of BP using ANN and the high frequency component using RNN with the selected predictors, mean errors of 0.05 ± 6.92 mmHg for systolic BP, and -0.05 ± 3.99 mmHg for diastolic BP were achieved. External validation of the model using another biosignal database consisting of 334 intensive care unit patients led to similar results, satisfying three standards for accuracy of BP monitors. The results indicate that the proposed method can contribute to the realization of ubiquitous non-invasive continuous BP monitoring.
Collapse
|
12
|
Seok W, Lee KJ, Cho D, Roh J, Kim S. Blood Pressure Monitoring System Using a Two-Channel Ballistocardiogram and Convolutional Neural Networks. SENSORS (BASEL, SWITZERLAND) 2021; 21:2303. [PMID: 33806118 PMCID: PMC8037981 DOI: 10.3390/s21072303] [Citation(s) in RCA: 11] [Impact Index Per Article: 3.7] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Grants] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 02/05/2021] [Revised: 03/17/2021] [Accepted: 03/22/2021] [Indexed: 12/22/2022]
Abstract
Hypertension is a chronic disease that kills 7.6 million people worldwide annually. A continuous blood pressure monitoring system is required to accurately diagnose hypertension. Here, a chair-shaped ballistocardiogram (BCG)-based blood pressure estimation system was developed with no sensors attached to users. Two experimental sessions were conducted with 30 subjects. In the first session, two-channel BCG and blood pressure data were recorded for each subject. In the second session, the two-channel BCG and blood pressure data were recorded after running on a treadmill and then resting on the newly developed system. The empirical mode decomposition algorithm was used to remove noise in the two-channel BCG, and the instantaneous phase was calculated by applying a Hilbert transform to the first intrinsic mode functions. After training a convolutional neural network regression model that predicts the systolic and diastolic blood pressures (SBP and DBP) from the two-channel BCG phase, the results of the first session (rest) and second session (recovery) were compared. The results confirmed that the proposed model accurately estimates the rapidly rising blood pressure in the recovery state. Results from the rest sessions satisfied the Association for the Advancement of Medical Instrumentation (AAMI) international standards. The standard deviation of the SBP results in the recovery session exceeded 0.7.
Collapse
Affiliation(s)
- Woojoon Seok
- Human Convergence Technology R&D Department, Korea Institute of Industrial Technology, 143 Hanggaulro, Ansan 15588, Korea; (W.S.); (J.R.)
- Deep Medi Research Institute of Technology, Deep Medi Inc., Seoul 06232, Korea; (K.J.L.); (D.C.)
| | - Kwang Jin Lee
- Deep Medi Research Institute of Technology, Deep Medi Inc., Seoul 06232, Korea; (K.J.L.); (D.C.)
| | - Dongrae Cho
- Deep Medi Research Institute of Technology, Deep Medi Inc., Seoul 06232, Korea; (K.J.L.); (D.C.)
| | - Jongryun Roh
- Human Convergence Technology R&D Department, Korea Institute of Industrial Technology, 143 Hanggaulro, Ansan 15588, Korea; (W.S.); (J.R.)
| | - Sayup Kim
- Human Convergence Technology R&D Department, Korea Institute of Industrial Technology, 143 Hanggaulro, Ansan 15588, Korea; (W.S.); (J.R.)
| |
Collapse
|
13
|
Luo J, Zhen J, Zhou P, Chen W, Guo Y. An iPPG-Based Device for Pervasive Monitoring of Multi-Dimensional Cardiovascular Hemodynamics. SENSORS 2021; 21:s21030872. [PMID: 33525472 PMCID: PMC7865369 DOI: 10.3390/s21030872] [Citation(s) in RCA: 3] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 11/20/2020] [Revised: 12/18/2020] [Accepted: 12/22/2020] [Indexed: 11/16/2022]
Abstract
Hemodynamic activities, as an essential measure of physiological and psychological characteristics, can be used for cardiovascular and cerebrovascular disease detection. Photoplethysmography imaging (iPPG) can be applied for such purposes with non-contact advances, however, most cardiovascular hemodynamics of iPPG systems are developed for laboratory research, which limits the application in pervasive healthcare. In this study, a video-based facial iPPG detecting equipment was devised to provide multi-dimensional spatiotemporal hemodynamic pulsations for applications with high portability and self-monitoring requirements. A series of algorithms have also been developed for physiological indices such as heart rate and breath rate extraction, facial region analysis, and visualization of hemodynamic pulsation distribution. Results showed that the new device can provide a reliable measurement of a rich range of cardiovascular hemodynamics. Combined with the advanced computing techniques, the new non-contact iPPG system provides a promising solution for user-friendly pervasive healthcare.
Collapse
Affiliation(s)
- Jingjing Luo
- Institute of AI and Robotics, Academy for Engineering and Technology, Fudan University, Shanghai 200433, China;
- Jihua Laboratory, Guangdong 528000, China;
| | - Junjie Zhen
- School of Precision Instruments and Opto-Electronics Engineering, Tianjin University, Tianjin 300072, China;
| | - Peng Zhou
- Jihua Laboratory, Guangdong 528000, China;
- School of Precision Instruments and Opto-Electronics Engineering, Tianjin University, Tianjin 300072, China;
| | - Wei Chen
- Center for Intelligent Medical Electronics, School of Information Science and Technology, Fudan University, Shanghai 200433, China;
- Human Phenome Institute, Fudan University, Shanghai 200433, China
| | - Yuzhu Guo
- School of Automation Science and Electrical Engineering, Beihang University, Beijing 100191, China
- Correspondence:
| |
Collapse
|
14
|
Ding X, Clifton D, Ji N, Lovell NH, Bonato P, Chen W, Yu X, Xue Z, Xiang T, Long X, Xu K, Jiang X, Wang Q, Yin B, Feng G, Zhang YT. Wearable Sensing and Telehealth Technology with Potential Applications in the Coronavirus Pandemic. IEEE Rev Biomed Eng 2021; 14:48-70. [PMID: 32396101 DOI: 10.1109/rbme.2020.2992838] [Citation(s) in RCA: 103] [Impact Index Per Article: 34.3] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 12/15/2022]
Abstract
Coronavirus disease 2019 (COVID-19) has emerged as a pandemic with serious clinical manifestations including death. A pandemic at the large-scale like COVID-19 places extraordinary demands on the world's health systems, dramatically devastates vulnerable populations, and critically threatens the global communities in an unprecedented way. While tremendous efforts at the frontline are placed on detecting the virus, providing treatments and developing vaccines, it is also critically important to examine the technologies and systems for tackling disease emergence, arresting its spread and especially the strategy for diseases prevention. The objective of this article is to review enabling technologies and systems with various application scenarios for handling the COVID-19 crisis. The article will focus specifically on 1) wearable devices suitable for monitoring the populations at risk and those in quarantine, both for evaluating the health status of caregivers and management personnel, and for facilitating triage processes for admission to hospitals; 2) unobtrusive sensing systems for detecting the disease and for monitoring patients with relatively mild symptoms whose clinical situation could suddenly worsen in improvised hospitals; and 3) telehealth technologies for the remote monitoring and diagnosis of COVID-19 and related diseases. Finally, further challenges and opportunities for future directions of development are highlighted.
Collapse
|
15
|
Pandey RK, Chao PCP. External temperature sensor assisted a new low power photoplethysmography readout system for accurate measurement of the bio-signs. MICROSYSTEM TECHNOLOGIES : SENSORS, ACTUATORS, SYSTEMS INTEGRATION 2020; 27:2315-2343. [PMID: 33281302 PMCID: PMC7695241 DOI: 10.1007/s00542-020-05106-y] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Figures] [Subscribe] [Scholar Register] [Received: 11/01/2020] [Accepted: 11/07/2020] [Indexed: 06/12/2023]
Abstract
This study presents an external temperature sensor assisted a new low power, time-interleave, wide dynamic range, and low DC drift photoplethysmography (PPG) signal acquisition system to obtain the accurate measurement of various bio signs in real-time. The designed chip incorporates a 2-bit control programmable transimpedance amplifier (TIA), a high order filter, a 3:8 programmable gain amplifier (PGA) and 2 × 2 organic light-emitting diode (OLED) driver. Temperature sensor is used herein to compensate the adverse effect of low-skin-temperature on the PPG signal quality. The analog front-end circuit is implemented in the integrated chip with chip area of 2008 μm × 1377 μm and fabricated via TSMC T18 process. With the standard 1.8 V, the experimental result shows that the measured current sensing range is 20 nA-100 uA. The measured dynamic range of the designed readout circuit is 80 dB. The estimated signal to noise ratio is 60 dB@1 uA, and the measured input referred noise is 60.2 pA/Hz½. The total power consumption of the designed chip is 31.32 µW (readout) + 1.62 mW (OLED driver@100% duty cycle). The non-invasive PPG sensor is applied to the wrist artery of the 40 healthy subjects for sensing the pulsation of the blood vessel. The experimental results show that for every 1 °C decrease in mean ambient temperature tends to 0.06 beats/min, 0.125 mmHg and 0.063 mmHg increase in hear rate (HR), systolic (SBP) and diastolic (DBP), respectively. Similarly, for every 1 °C increase in mean ambient temperature tends to 0.13 beats/min, 0.601 mmHg and 0.121 mmHg increase in HR, SBP and DBP, respectively. The measured accuracy and standard error for the HR estimation are 96%, and - 0.022 ± 2.589 beats/minute, respectively. The oxygen stauration (SpO2) measurement results shows that the mean absolute percentage error is less than 5%. The resultant errors for the SBP and DBP measurement are - 0.318 ± 5.19 mmHg and - 0.5 ± 1.91 mmHg, respectively.
Collapse
Affiliation(s)
- Rajeev Kumar Pandey
- EECS International Graduate Program, National Chiao Tung University, Hsinchu, 300 Taiwan
| | - Paul C.-P. Chao
- Department of Electrical Engineering, National Chiao Tung University, Hsinchu, 300 Taiwan
| |
Collapse
|
16
|
Landry C, Hedge ET, Hughson RL, Peterson SD, Arami A. Cuffless Blood Pressure Estimation for Activities of Daily Living. ANNUAL INTERNATIONAL CONFERENCE OF THE IEEE ENGINEERING IN MEDICINE AND BIOLOGY SOCIETY. IEEE ENGINEERING IN MEDICINE AND BIOLOGY SOCIETY. ANNUAL INTERNATIONAL CONFERENCE 2020; 2020:4441-4445. [PMID: 33018980 DOI: 10.1109/embc44109.2020.9175976] [Citation(s) in RCA: 4] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 11/10/2022]
Abstract
This work presents a modelling approach to predict the blood pressure (BP) waveform time series during activities of daily living without the use of a traditional pressure cuff. A nonlinear autoregressive model with exogenous inputs (NARX) is implemented using artificial neural networks and trained to predict the BP waveform time series from electrocardiography (ECG) and forehead photoplethysmography (PPG) input signals. To broaden the range of blood pressures present in the training set, a protocol was implemented that included sitting, standing, walking, Valsalva manoeuvers, and static handgrip exercise. A five-minute interval of data in the sitting position at the end of the day was also used for training. The efficacy of the cuffless BP method for continuous BP estimation over 4.67 hours was evaluated on 3 participants for varying training data segments. A mean absolute error of 6.3 and 5.2 mmHg were achieved for systolic BP and diastolic BP estimates, respectively. Including static handgrips and Valsalva manoeuvers in the training dataset leads to better estimation of the higher ranges of BP observed throughout the day. The proposed method shows potential for estimating the range of BP experienced during activities of daily living.Clinical Relevance- Establishes a method for cuffless continuous blood pressure estimation during activities of daily living that can be used for continuous monitoring and acute hypertension detection.
Collapse
|
17
|
Draft Proposal of an Optical Cuffless Blood Pressure Device. HEALTH AND TECHNOLOGY 2020. [DOI: 10.1007/s12553-020-00435-4] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 10/24/2022]
|
18
|
Pandit JA, Lores E, Batlle D. Cuffless Blood Pressure Monitoring: Promises and Challenges. Clin J Am Soc Nephrol 2020; 15:1531-1538. [PMID: 32680913 PMCID: PMC7536750 DOI: 10.2215/cjn.03680320] [Citation(s) in RCA: 34] [Impact Index Per Article: 8.5] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 01/08/2023]
Abstract
Current BP measurements are on the basis of traditional BP cuff approaches. Ambulatory BP monitoring, at 15- to 30-minute intervals usually over 24 hours, provides sufficiently continuous readings that are superior to the office-based snapshot, but this system is not suitable for frequent repeated use. A true continuous BP measurement that could collect BP passively and frequently would require a cuffless method that could be worn by the patient, with the data stored electronically much the same way that heart rate and heart rhythm are already done routinely. Ideally, BP should be measured continuously and frequently during diverse activities during both daytime and nighttime in the same subject by means of novel devices. There is increasing excitement for newer methods to measure BP on the basis of sensors and algorithm development. As new devices are refined and their accuracy is improved, it will be possible to better assess masked hypertension, nocturnal hypertension, and the severity and variability of BP. In this review, we discuss the progression in the field, particularly in the last 5 years, ending with sensor-based approaches that incorporate machine learning algorithms to personalized medicine.
Collapse
Affiliation(s)
- Jay A Pandit
- Division of Cardiology, Northwestern University Feinberg School of Medicine, Chicago, Illinois
| | - Enrique Lores
- Division of Nephrology and Hypertension, Northwestern University Feinberg School of Medicine, Chicago, Illinois
| | - Daniel Batlle
- Division of Nephrology and Hypertension, Northwestern University Feinberg School of Medicine, Chicago, Illinois
| |
Collapse
|
19
|
Multimodal Photoplethysmography-Based Approaches for Improved Detection of Hypertension. J Clin Med 2020; 9:jcm9041203. [PMID: 32331360 PMCID: PMC7230564 DOI: 10.3390/jcm9041203] [Citation(s) in RCA: 20] [Impact Index Per Article: 5.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 03/09/2020] [Revised: 04/07/2020] [Accepted: 04/13/2020] [Indexed: 12/14/2022] Open
Abstract
Elevated blood pressure (BP) is a major cause of death, yet hypertension commonly goes undetected. Owing to its nature, it is typically asymptomatic until later in its progression when the vessel or organ structure has already been compromised. Therefore, noninvasive and continuous BP measurement methods are needed to ensure appropriate diagnosis and early management before hypertension leads to irreversible complications. Photoplethysmography (PPG) is a noninvasive technology with waveform morphologies similar to that of arterial BP waveforms, therefore attracting interest regarding its usability in BP estimation. In recent years, wearable devices incorporating PPG sensors have been proposed to improve the early diagnosis and management of hypertension. Additionally, the need for improved accuracy and convenience has led to the development of devices that incorporate multiple different biosignals with PPG. Through the addition of modalities such as an electrocardiogram, a final measure of the pulse wave velocity is derived, which has been proved to be inversely correlated to BP and to yield accurate estimations. This paper reviews and summarizes recent studies within the period 2010–2019 that combined PPG with other biosignals and offers perspectives on the strengths and weaknesses of current developments to guide future advancements in BP measurement. Our literature review reveals promising measurement accuracies and we comment on the effective combinations of modalities and success of this technology.
Collapse
|
20
|
Shao J, Shi P, Hu S, Yu H. A Revised Point-to-Point Calibration Approach with Adaptive Errors Correction to Weaken Initial Sensitivity of Cuff-Less Blood Pressure Estimation. SENSORS 2020; 20:s20082205. [PMID: 32295090 PMCID: PMC7218878 DOI: 10.3390/s20082205] [Citation(s) in RCA: 7] [Impact Index Per Article: 1.8] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 02/21/2020] [Revised: 04/01/2020] [Accepted: 04/10/2020] [Indexed: 11/16/2022]
Abstract
Initial calibration is a great challenge for cuff-less blood pressure (BP) measurement. The traditional one point-to-point (oPTP) calibration procedure only uses one sample/point to obtain unknown parameters of a specific model in a calm state. In fact, parameters such as pulse transit time (PTT) and BP still have slight fluctuations at rest for each subject. The conventional oPTP method had a strong sensitivity in the selection of initial value. Yet, the initial sensitivity of calibration has not been reported and investigated in cuff-less BP motoring. In this study, a mean point-to-point (mPTP) paring calibration method through averaging and balancing calm or peaceful states was proposed for the first time. Thus, based on mPTP, a factor point-to-point (fPTP) paring calibration method through introducing the penalty factor was further proposed to improve and optimize the performance of BP estimation. Using the oPTP, mPTP, and fPTP methods, a total of more than 100,000 heartbeat samples from 21 healthy subjects were tested and validated in the PTT-based BP monitoring technologies. The results showed that the mPTP and fPTP methods significantly improved the performance of estimating BP compared to the conventional oPTP method. Moreover, the mPTP and fPTP methods could be widely popularized and applied, especially the fPTP method, on estimating cuff-less diastolic blood pressure (DBP). To this extent, the fPTP method weakens the initial calibration sensitivity of cuff-less BP estimation and fills in the ambiguity for individualized calibration procedure.
Collapse
Affiliation(s)
- Jiang Shao
- Institute of Rehabilitation Engineering and Technology, University of Shanghai for Science and Technology, Shanghai 200093, China
| | - Ping Shi
- Institute of Rehabilitation Engineering and Technology, University of Shanghai for Science and Technology, Shanghai 200093, China
- Correspondence:
| | - Sijung Hu
- Wolfson School of Mechanical, Electrical and Manufacturing Engineering, Loughborough University, Loughborough, Leicestershire LE11 3TU, UK
| | - Hongliu Yu
- Institute of Rehabilitation Engineering and Technology, University of Shanghai for Science and Technology, Shanghai 200093, China
| |
Collapse
|
21
|
Fierro G, Armentano R, Silveira F. Evaluation of transit time-based models in wearable central aortic blood pressure estimation. Biomed Phys Eng Express 2020; 6:035006. [PMID: 33438651 DOI: 10.1088/2057-1976/ab7a55] [Citation(s) in RCA: 2] [Impact Index Per Article: 0.5] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/11/2022]
Abstract
Evidence suggests that central aortic blood pressure (CABP) may provide a more accurate prognosis of cardiovascular events than peripheral pressure. The capability of monitoring CABP in a continuous, wearable, unobtrusive way might have a significant impact on hypertension management. The purpose of this study is to experimentally explore whether a wearable device equipped with an electrocardiogram (ECG) and ballistocardiogram (BCG) acquisition system could be used to predict CABP. This is based on state-of-the-art results on the relationship between transit time extracted from these signals and CABP. Ten young, healthy volunteers participated in the study where data-sets were acquired during three hemodynamic interventions, i.e., breath-holding, Valsalva maneuver, and cold pressor. Each data-set included ECG and BCG waveforms acquired by the wearable device and a CABP assessment from a cuff-based device. A total of nine PTT-based models (PBMs) derived from pulse transit time methodology were considered. Each PBM was tested with three alternative feature times extracted from the recorded waveforms PBMs were calibrated with data-sets acquired at baseline state, which were not considered for testing the PBM estimation performance. Four of the nine tested models presented a proper agreement in estimating CABP through the acquired signals, after the calibration procedure with baseline-state data. Results in one of these promising models are the following. Mean estimation error (95% confidence interval), systolic: 0 to 1.7 mmHg, diastolic: 0.4 to 2.3 mmHg, Pearson correlation: 0.82 systolic and 0.78 diastolic (p < 0.001). The proposed methodology may lead to continuous wearable BP monitoring.
Collapse
Affiliation(s)
- Germán Fierro
- Instituto de Ingeniería Eléctrica, Facultad de Ingeniería, Universidad de la República, Montevideo, Uruguay
| | | | | |
Collapse
|
22
|
Ohata T, Ishibashi K, Sun G. Non-Contact Blood Pressure Measurement Scheme Using Doppler Radar. ANNUAL INTERNATIONAL CONFERENCE OF THE IEEE ENGINEERING IN MEDICINE AND BIOLOGY SOCIETY. IEEE ENGINEERING IN MEDICINE AND BIOLOGY SOCIETY. ANNUAL INTERNATIONAL CONFERENCE 2020; 2019:778-781. [PMID: 31946011 DOI: 10.1109/embc.2019.8857056] [Citation(s) in RCA: 4] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 11/06/2022]
Abstract
A continuous cuffless non-contact blood pressure (BP) measurement scheme using Doppler radar is proposed. This non-contact BP estimation scheme uses the periods in which the heart beats and periods in which the heart contracts. These periods are obtained using Doppler radar signals. Diastolic BP (DBP) was estimated using the period in which the heart contracts. Pulse pressure (PP) was estimated using one period in which the heart beats and one period in which the heart contracts. Systolic BP (SBP) was obtained by the sum of the estimated DBP and PP. The correlation of the estimated BP and the BP acquired by the BP monitor was calculated. The correlation coefficients were 0.79 for SBP, 0.88 for DBP, and 0.81 for PP. The BP was successfully measured in a contactless manner.
Collapse
|
23
|
An Optimization Study of Estimating Blood Pressure Models Based on Pulse Arrival Time for Continuous Monitoring. JOURNAL OF HEALTHCARE ENGINEERING 2020; 2020:1078251. [PMID: 32104555 PMCID: PMC7035551 DOI: 10.1155/2020/1078251] [Citation(s) in RCA: 8] [Impact Index Per Article: 2.0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 07/06/2019] [Revised: 09/18/2019] [Accepted: 10/19/2019] [Indexed: 11/18/2022]
Abstract
Continuous blood pressure (BP) monitoring has a significant meaning for the prevention and early diagnosis of cardiovascular disease. However, under different calibration methods, it is difficult to determine which model is better for estimating BP. This study was firstly designed to reveal a better BP estimation model by evaluating and optimizing different BP models under a justified and uniform criterion, i.e., the advanced point-to-point pairing method (PTP). Here, the physical trial in this study caused the BP increase largely. In addition, the PPG and ECG signals were collected while the cuff bps were measured for each subject. The validation was conducted on four popular vascular elasticity (VE) models (MK-EE, L-MK, MK-BH, and dMK-BH) and one representative elastic tube (ET) model, i.e., M-M. The results revealed that the VE models except for L-MK outperformed the ET model. The linear L-MK as a VE model had the largest estimated error, and the nonlinear M-M model had a weaker correlation between the estimated BP and the cuff BP than MK-EE, MK-BH, and dMK-BH models. Further, in contrast to L-MK, the dMK-BH model had the strongest correlation and the smallest difference between the estimated BP and the cuff BP including systolic blood pressure (SBP) and diastolic blood pressure (DBP) than others. In this study, the simple MK-EE model showed the best similarity to the dMK-BH model. There were no significant changes between MK-EE and dMK-BH models. These findings indicated that the nonlinear MK-EE model with low estimated error and simple mathematical expression was a good choice for application in wearable sensor devices for cuff-less BP monitoring compared to others.
Collapse
|
24
|
Development of a Cuff-Less Blood Pressure Monitoring System and Its Application. ADVANCES IN EXPERIMENTAL MEDICINE AND BIOLOGY 2020. [PMID: 31893426 DOI: 10.1007/978-3-030-34461-0_40] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register]
Abstract
We present an unobtrusive cuff-less sphygmomanometer based on contact-type and optical pulse sensors for continuous and minimally invasive monitoring of blood pressure (BP). We developed a cuff-less sphygmomanometer that utilizes the pulse arrival time (PAT) to estimate continuous BP. To assess its accuracy, we recruited 10 healthy subjects in whom we carried out BP studies using the cuff-less sphygmomanometer compared with a standard cuff-type device in a stationary sitting patient. Preliminary results showed that the mean difference (MD) of estimated systolic blood pressure and diastolic blood pressure were 0.96 ± 9.6 (mean ± SD) mmHg and 1.14 ± 7.5 mmHg, respectively, compared to the control. The corresponding correlation between the estimated BP values and controls were 0.78 for systolic blood pressure (p < 0.01) and 0.69 for diastolic blood pressure (p < 0.01); thus, there were significant correlations. These results suggest that the developed cuff-less sphygmomanometer has the potential for continuous BP monitoring. Finally, we conducted a preliminary study of simultaneous monitoring of cuff-less BP and near-infrared spectroscopy to evaluate the potential for assessment of autonomic nervous system functions during mental stress tasks.
Collapse
|
25
|
Rastegar S, GholamHosseini H, Lowe A. Non-invasive continuous blood pressure monitoring systems: current and proposed technology issues and challenges. AUSTRALASIAN PHYSICAL & ENGINEERING SCIENCES IN MEDICINE 2019; 43:10.1007/s13246-019-00813-x. [PMID: 31677058 DOI: 10.1007/s13246-019-00813-x] [Citation(s) in RCA: 23] [Impact Index Per Article: 4.6] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Received: 05/16/2019] [Accepted: 10/25/2019] [Indexed: 01/03/2023]
Abstract
High blood pressure (BP) or hypertension is the single most crucial adjustable risk factor for cardiovascular diseases (CVDs) and monitoring the arterial blood pressure (ABP) is an efficient way to detect and control the prevalence of the cardiovascular health of patients. Therefore, monitoring the regulation of BP during patients' daily life plays a critical role in the ambulatory setting and the latest mobile health technology. In recent years, many studies have been conducted to explore the feasibility and performance of such techniques in the health care system. The ultimate aim of these studies is to find and develop an alternative to conventional BP monitoring by using cuff-less, easy-to-use, fast, and cost-effective devices for controlling and lowering the physical harm of CVDs to the human body. However, most of the current studies are at the prototype phase and face a range of issues and challenges to meet clinical standards. This review focuses on the description and analysis of the latest continuous and cuff-less methods along with their key challenges and barriers. Particularly, most advanced and standard technologies including pulse transit time (PTT), ultrasound, pulse arrival time (PAT), and machine learning are investigated. The accuracy, portability, and comfort of use of these technologies, and the ability to integrate to the wearable healthcare system are discussed. Finally, the future directions for further study are suggested.
Collapse
Affiliation(s)
- Solmaz Rastegar
- School of Engineering, Computer, and Mathematical Sciences, Auckland University of Technology, Private Bag 92006, Auckland, New Zealand.
| | - Hamid GholamHosseini
- School of Engineering, Computer, and Mathematical Sciences, Auckland University of Technology, Private Bag 92006, Auckland, New Zealand
| | - Andrew Lowe
- School of Engineering, Computer, and Mathematical Sciences, Auckland University of Technology, Private Bag 92006, Auckland, New Zealand
| |
Collapse
|
26
|
Lee J, Yang S, Lee S, Kim HC. Analysis of Pulse Arrival Time as an Indicator of Blood Pressure in a Large Surgical Biosignal Database: Recommendations for Developing Ubiquitous Blood Pressure Monitoring Methods. J Clin Med 2019; 8:E1773. [PMID: 31653002 PMCID: PMC6912522 DOI: 10.3390/jcm8111773] [Citation(s) in RCA: 29] [Impact Index Per Article: 5.8] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 09/19/2019] [Revised: 10/16/2019] [Accepted: 10/22/2019] [Indexed: 01/03/2023] Open
Abstract
As non-invasive continuous blood pressure monitoring (NCBPM) has gained wide attraction in the recent decades, many pulse arrival time (PAT) or pulse transit time (PTT) based blood pressure (BP) estimation studies have been conducted. However, most of the studies have used small homogeneous subject pools to generate models of BP based on particular interventions for induced hemodynamic change. In this study, a large open biosignal database from a diverse group of 2309 surgical patients was analyzed to assess the efficacy of PAT, PTT, and confounding factors on the estimation of BP. After pre-processing the dataset, a total of 6,777,308 data pairs of BP and temporal features between electrocardiogram (ECG) and photoplethysmogram (PPG) were extracted and analyzed. Correlation analysis revealed that PAT or PTT extracted from the intersecting-tangent (IT) point of PPG showed the highest mean correlation to BP. The mean correlation between PAT and systolic blood pressure (SBP) was -0.37 and the mean correlation between PAT and diastolic blood pressure (DBP) was -0.30, outperforming the correlation between BP and PTT at -0.12 for SBP and -0.11 for DBP. A linear model of BP with a simple calibration method using PAT as a predictor was developed which satisfied international standards for automatic oscillometric BP monitors in the case of DBP, however, SBP could not be predicted to a satisfactory level due to higher errors. Furthermore, multivariate regression analyses showed that many confounding factors considered in previous studies had inconsistent effects on the degree of correlation between PAT and BP.
Collapse
Affiliation(s)
- Joonnyong Lee
- Seoul National University Hospital Biomedical Research Institute, Seoul 03080, Korea.
| | - Seungman Yang
- Interdisciplinary Program in Bioengineering, Seoul National University Graduate School, Seoul 03080, Korea.
| | - Saram Lee
- Seoul National University Hospital Biomedical Research Institute, Seoul 03080, Korea.
| | - Hee Chan Kim
- Department of Biomedical Engineering, College of Medicine, Seoul National University, Seoul 03080, Korea.
- Institute of Medical & Biological Engineering, Medical Research Center, Seoul National University, Seoul 03080, Korea.
| |
Collapse
|
27
|
Attarpour A, Mahnam A, Aminitabar A, Samani H. Cuff-less continuous measurement of blood pressure using wrist and fingertip photo-plethysmograms: Evaluation and feature analysis. Biomed Signal Process Control 2019. [DOI: 10.1016/j.bspc.2018.12.006] [Citation(s) in RCA: 13] [Impact Index Per Article: 2.6] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 10/27/2022]
|
28
|
A Chair-Based Unconstrained/Nonintrusive Cuffless Blood Pressure Monitoring System Using a Two-Channel Ballistocardiogram. SENSORS 2019; 19:s19030595. [PMID: 30708934 PMCID: PMC6387459 DOI: 10.3390/s19030595] [Citation(s) in RCA: 14] [Impact Index Per Article: 2.8] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 12/21/2018] [Revised: 01/29/2019] [Accepted: 01/29/2019] [Indexed: 11/25/2022]
Abstract
Hypertension is a well-known chronic disease that causes complications such as cardiovascular diseases or stroke, and thus needs to be continuously managed by using a simple system for measuring blood pressure. The existing method for measuring blood pressure uses a wrapping cuff, which makes measuring difficult for patients. To address this problem, cuffless blood pressure measurement methods that detect the peak pressure via signals measured using photoplethysmogram (PPG) and electrocardiogram (ECG) sensors and use it to calculate the pulse transit time (PTT) or pulse wave velocity (PWV) have been studied. However, a drawback of these methods is that a user must be able to recognize and establish contact with the sensor. Furthermore, the peak of the PPG or ECG cannot be detected if the signal quality drops, leading to a decrease in accuracy. In this study, a chair-type system that can monitor blood pressure using polyvinylidene fluoride (PVDF) films in a nonintrusive manner to users was developed. The proposed method also uses instantaneous phase difference (IPD) instead of PTT as the feature value for estimating blood pressure. Experiments were conducted using a blood pressure estimation model created via an artificial neural network (ANN), which showed that IPD could estimate more accurate readings of blood pressure compared to PTT, thus demonstrating the possibility of a nonintrusive blood pressure monitoring system.
Collapse
|
29
|
Hou Z, Xiang J, Dong Y, Xue X, Xiong H, Yang B. Capturing Electrocardiogram Signals from Chairs by Multiple Capacitively Coupled Unipolar Electrodes. SENSORS (BASEL, SWITZERLAND) 2018; 18:E2835. [PMID: 30154303 PMCID: PMC6163948 DOI: 10.3390/s18092835] [Citation(s) in RCA: 6] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 07/27/2018] [Revised: 08/18/2018] [Accepted: 08/21/2018] [Indexed: 11/21/2022]
Abstract
A prototype of an electrocardiogram (ECG) signal acquisition system with multiple unipolar capacitively coupled electrodes is designed and experimentally tested. Capacitively coupled electrodes made of a standard printed circuit board (PCB) are used as the sensing electrodes. Different from the conventional measurement schematics, where one single lead ECG signal is acquired from a pair of sensing electrodes, the sensing electrodes in our approaches operate in a unipolar mode, i.e., the biopotential signals picked up by each sensing electrodes are amplified and sampled separately. Four unipolar electrodes are mounted on the backrest of a regular chair and therefore four channel of signals containing ECG information are sampled and processed. It is found that the qualities of ECG signal contained in the four channel are different from each other. In order to pick up the ECG signal, an index for quality evaluation, as well as for aggregation of multiple signals, is proposed based on phase space reconstruction. Experimental tests are carried out while subjects sitting on the chair and clothed. The results indicate that the ECG signals can be reliably obtained in such a unipolar way.
Collapse
Affiliation(s)
- Zhongjie Hou
- State Key Laboratory of Precision Measurement Technology and Instruments, Department of Precision Instrument, Tsinghua University, Beijing 100084, China.
| | - Jinxi Xiang
- State Key Laboratory of Precision Measurement Technology and Instruments, Department of Precision Instrument, Tsinghua University, Beijing 100084, China.
| | - Yonggui Dong
- State Key Laboratory of Precision Measurement Technology and Instruments, Department of Precision Instrument, Tsinghua University, Beijing 100084, China.
| | - Xiaohui Xue
- State Key Laboratory of Precision Measurement Technology and Instruments, Department of Precision Instrument, Tsinghua University, Beijing 100084, China.
| | - Hao Xiong
- State Key Laboratory of Precision Measurement Technology and Instruments, Department of Precision Instrument, Tsinghua University, Beijing 100084, China.
| | - Bin Yang
- State Key Laboratory of Precision Measurement Technology and Instruments, Department of Precision Instrument, Tsinghua University, Beijing 100084, China.
| |
Collapse
|
30
|
Lee J, Sohn J, Park J, Yang S, Lee S, Kim HC. Novel blood pressure and pulse pressure estimation based on pulse transit time and stroke volume approximation. Biomed Eng Online 2018; 17:81. [PMID: 29914491 PMCID: PMC6006984 DOI: 10.1186/s12938-018-0510-8] [Citation(s) in RCA: 21] [Impact Index Per Article: 3.5] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 12/19/2017] [Accepted: 06/05/2018] [Indexed: 01/14/2023] Open
Abstract
BACKGROUND Non-invasive continuous blood pressure monitors are of great interest to the medical community due to their value in hypertension management. Recently, studies have shown the potential of pulse pressure as a therapeutic target for hypertension, but not enough attention has been given to non-invasive continuous monitoring of pulse pressure. Although accurate pulse pressure estimation can be of direct value to hypertension management and indirectly to the estimation of systolic blood pressure, as it is the sum of pulse pressure and diastolic blood pressure, only a few inadequate methods of pulse pressure estimation have been proposed. METHODS We present a novel, non-invasive blood pressure and pulse pressure estimation method based on pulse transit time and pre-ejection period. Pre-ejection period and pulse transit time were measured non-invasively using electrocardiogram, seismocardiogram, and photoplethysmogram measured from the torso. The proposed method used the 2-element Windkessel model to model pulse pressure with the ratio of stroke volume, approximated by pre-ejection period, and arterial compliance, estimated by pulse transit time. Diastolic blood pressure was estimated using pulse transit time, and systolic blood pressure was estimated as the sum of the two estimates. The estimation method was verified in 11 subjects in two separate conditions with induced cardiovascular response and the results were compared against a reference measurement and values obtained from a previously proposed method. RESULTS The proposed method yielded high agreement with the reference (pulse pressure correlation with reference R ≥ 0.927, diastolic blood pressure correlation with reference R ≥ 0.854, systolic blood pressure correlation with reference R ≥ 0.914) and high estimation accuracy in pulse pressure (mean root-mean-squared error ≤ 3.46 mmHg) and blood pressure (mean root-mean-squared error ≤ 6.31 mmHg for diastolic blood pressure and ≤ 8.41 mmHg for systolic blood pressure) over a wide range of hemodynamic changes. CONCLUSION The proposed pulse pressure estimation method provides accurate estimates in situations with and without significant changes in stroke volume. The proposed method improves upon the currently available systolic blood pressure estimation methods by providing accurate pulse pressure estimates.
Collapse
Affiliation(s)
- Joonnyong Lee
- Interdisciplinary Program for Bioengineering, Seoul National University Graduate School, Suite 321, Building 8, 101 Daehak-Ro, Jongno-Gu, Seoul, 03080, Republic of Korea
| | - JangJay Sohn
- Interdisciplinary Program for Bioengineering, Seoul National University Graduate School, Suite 321, Building 8, 101 Daehak-Ro, Jongno-Gu, Seoul, 03080, Republic of Korea
| | - Jonghyun Park
- Interdisciplinary Program for Bioengineering, Seoul National University Graduate School, Suite 321, Building 8, 101 Daehak-Ro, Jongno-Gu, Seoul, 03080, Republic of Korea
| | - SeungMan Yang
- Interdisciplinary Program for Bioengineering, Seoul National University Graduate School, Suite 321, Building 8, 101 Daehak-Ro, Jongno-Gu, Seoul, 03080, Republic of Korea
| | - Saram Lee
- Seoul National University Hospital Biomedical Research Institute, Suite 1203-1, 71 Daehak-ro, Jongno-gu, Seoul, 03082, Republic of Korea.
| | - Hee Chan Kim
- Department of Biomedical Engineering, Seoul National University College of Medicine, Suite 11315, 101 Daehak-ro, Jongno-gu, Seoul, 03080, Republic of Korea. .,The Institute of Medical and Biological Engineering, Medical Research Center, Seoul National University, Suite 11315, 101 Daehak-ro, Jongno-gu, Seoul, 03080, Republic of Korea.
| |
Collapse
|
31
|
Wang Y, Liu Z, Ma S. Cuff-less blood pressure measurement from dual-channel photoplethysmographic signals via peripheral pulse transit time with singular spectrum analysis. Physiol Meas 2018; 39:025010. [DOI: 10.1088/1361-6579/aa996d] [Citation(s) in RCA: 21] [Impact Index Per Article: 3.5] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/12/2022]
|
32
|
Radha M, Zhang G, Gelissen J, Groot KD, Haakma R, Aarts RM. Arterial path selection to measure pulse wave velocity as a surrogate marker of blood pressure. Biomed Phys Eng Express 2017. [DOI: 10.1088/2057-1976/aa5b40] [Citation(s) in RCA: 7] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 12/17/2022]
|