1
|
Barbruni GL, Cordara C, Carminati M, Carrara S, Ghezzi D. A Frequency-Switching Inductive Power Transfer System for Wireless, Miniaturised and Large-Scale Neural Interfaces. IEEE TRANSACTIONS ON BIOMEDICAL CIRCUITS AND SYSTEMS 2024; 18:679-690. [PMID: 38285578 DOI: 10.1109/tbcas.2024.3359481] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 01/31/2024]
Abstract
Three-coil inductive power transfer is the state-of-the-art solution to power multiple miniaturised neural implants. However, the maximum delivered power is limited by the efficiency of the powering link and safety constrains. Here we propose a frequency-switching inductive link, where the passive resonator normally used in a three-coil link is replaced by an active resonator. It receives power from the external transmitter via a two-coil inductive link at the low frequency of 13.56 MHz. Then, it switches the operating frequency to the higher frequency of 433.92 MHz through a dedicated circuitry. Last, it transmits power to 1024 miniaturised implants via a three-coil inductive link using an array of 37 focusing resonators for a brain coverage of 163.84 mm 2. Our simulations reported a power transfer efficiency of 0.013 % and a maximum power delivered to the load of 1970 μW under safety-constrains, which are respectively two orders of magnitude and more than six decades higher compared to an equivalent passive three-coil link. The frequency-switching inductive system is a scalable and highly versatile solution for wireless, miniaturised and large-scale neural interfaces.
Collapse
|
2
|
Mukherjee D, Rainu SK, Singh N, Mallick D. A Miniaturized, Low-Frequency Magnetoelectric Wireless Power Transfer System for Powering Biomedical Implants. IEEE TRANSACTIONS ON BIOMEDICAL CIRCUITS AND SYSTEMS 2024; 18:438-450. [PMID: 37999967 DOI: 10.1109/tbcas.2023.3336598] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 11/26/2023]
Abstract
This work experimentally demonstrates the operation of a miniaturized magnetoelectric (ME) wireless power transfer (WPT) system by incorporating a ME transducer and a suitable interface power management circuit (PMC) for potentially powering implantable medical devices (IMD) wirelessly. A ME heterostructure is micromachined to obtain desired device dimensions of 3.5 × 5 mm 2 and to restrict the operating frequency at a clinically approved frequency of 50 kHz. The proposed work also aims to address the trade-off between the device miniaturization, power attenuation and limiting the specific absorption rate (SAR) in the human tissue. By limiting the operating frequency to 50 kHz, the SAR is reduced to less than 1 μW/kg. The fabricated device is characterized with low-intensity AC magnetic field up to 40 μT without using any DC bias, resulting in 0.4 V output voltage and 6.6 μW power across 8 k Ω load. Alignment misorientation between the Tx and Rx is studied for in-plane and out-of-plane angular rotations to confirm the device's reliability against angular misalignment. By eliminating the bulky biasing magnets, the proposed device achieves a significant size reduction compared to the previously reported works. In addition, a self-powered interface PMC is incorporated with the ME system. The PMC generates 3.5 V regulated DC voltage from the input AC voltage range 0.7 V to 3.3 V. The PMC is fabricated on a 2-layered PCB and the over all ME WPT system consumes 12 × 12 mm 2 area. The overall PMC has intrinsic current consumption less than 550 nA with peak power conversion efficiency higher than 85 %. The in vitro cytotoxicity analysis in the human hepatic cell line WRL-68 confirmed the biocompatibility of the Parylene-C encapsulated ME device for up to 7 days, suggesting its potential use in implantable electronic devices for biomedical and clinical applications.
Collapse
|
3
|
Mahmud S, Nezaratizadeh A, Satriya AB, Yoon YK, Ho JS, Khalifa A. Harnessing metamaterials for efficient wireless power transfer for implantable medical devices. Bioelectron Med 2024; 10:7. [PMID: 38444001 PMCID: PMC10916182 DOI: 10.1186/s42234-023-00136-z] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Journal Information] [Subscribe] [Scholar Register] [Received: 10/12/2023] [Accepted: 12/07/2023] [Indexed: 03/07/2024] Open
Abstract
Wireless power transfer (WPT) within the human body can enable long-lasting medical devices but poses notable challenges, including absorption by biological tissues and weak coupling between the transmitter (Tx) and receiver (Rx). In pursuit of more robust and efficient wireless power, various innovative strategies have emerged to optimize power transfer efficiency (PTE). One such groundbreaking approach stems from the incorporation of metamaterials, which have shown the potential to enhance the capabilities of conventional WPT systems. In this review, we delve into recent studies focusing on WPT systems that leverage metamaterials to achieve increased efficiency for implantable medical devices (IMDs) in the electromagnetic paradigm. Alongside a comparative analysis, we also outline current challenges and envision potential avenues for future advancements.
Collapse
Affiliation(s)
- Sultan Mahmud
- Department of Electrical and Computer Engineering, University of Florida, Gainesville, FL, 32611, USA
| | - Ali Nezaratizadeh
- Department of Electrical and Computer Engineering, University of Florida, Gainesville, FL, 32611, USA
| | - Alfredo Bayu Satriya
- Department of Electrical and Computer Engineering, University of Florida, Gainesville, FL, 32611, USA
| | - Yong-Kyu Yoon
- Department of Electrical and Computer Engineering, University of Florida, Gainesville, FL, 32611, USA
| | - John S Ho
- Department of Electrical and Computer Engineering, National University of Singapore, Singapore, Singapore
| | - Adam Khalifa
- Department of Electrical and Computer Engineering, University of Florida, Gainesville, FL, 32611, USA.
| |
Collapse
|
4
|
Nair V, Dalrymple AN, Yu Z, Balakrishnan G, Bettinger CJ, Weber DJ, Yang K, Robinson JT. Miniature battery-free bioelectronics. Science 2023; 382:eabn4732. [PMID: 37943926 DOI: 10.1126/science.abn4732] [Citation(s) in RCA: 1] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 06/10/2022] [Accepted: 09/28/2023] [Indexed: 11/12/2023]
Abstract
Miniature wireless bioelectronic implants that can operate for extended periods of time can transform how we treat disorders by acting rapidly on precise nerves and organs in a way that drugs cannot. To reach this goal, materials and methods are needed to wirelessly transfer energy through the body or harvest energy from the body itself. We review some of the capabilities of emerging energy transfer methods to identify the performance envelope for existing technology and discover where opportunities lie to improve how much-and how efficiently-we can deliver energy to the tiny bioelectronic implants that can support emerging medical technologies.
Collapse
Affiliation(s)
- Vishnu Nair
- Rice Neuroengineering Initiative, Rice University, Houston, TX, USA
| | - Ashley N Dalrymple
- Department of Mechanical Engineering, Carnegie Mellon University, Pittsburgh, PA, USA
- Department of Biomedical Engineering, University of Utah, Salt Lake City, UT, USA
- Department of Physical Medicine and Rehabilitation, University of Utah, Salt Lake City, UT, USA
| | - Zhanghao Yu
- Department of Electrical and Computer Engineering, Rice University, Houston, TX, USA
| | - Gaurav Balakrishnan
- Department of Materials Science & Engineering, Carnegie Mellon University, Pittsburgh, PA, USA
| | - Christopher J Bettinger
- Department of Materials Science & Engineering, Carnegie Mellon University, Pittsburgh, PA, USA
| | - Douglas J Weber
- Department of Mechanical Engineering, Carnegie Mellon University, Pittsburgh, PA, USA
- Neuroscience Institute, Carnegie Mellon University, Pittsburgh, PA, USA
- Center for Neural Basis of Cognition, Pittsburgh, PA, USA
| | - Kaiyuan Yang
- Department of Electrical and Computer Engineering, Rice University, Houston, TX, USA
| | - Jacob T Robinson
- Rice Neuroengineering Initiative, Rice University, Houston, TX, USA
- Department of Electrical and Computer Engineering, Rice University, Houston, TX, USA
| |
Collapse
|
5
|
Walsh C, Muttlak SG, Sadeghi M, Missous M. Miniature Integrated 2.4 GHz Rectennas Using Novel Tunnel Diodes. SENSORS (BASEL, SWITZERLAND) 2023; 23:6409. [PMID: 37514704 PMCID: PMC10386477 DOI: 10.3390/s23146409] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Received: 05/25/2023] [Revised: 06/26/2023] [Accepted: 07/11/2023] [Indexed: 07/30/2023]
Abstract
This work presents the design, fabrication, and measured results of a fully integrated miniature rectenna using a novel tunnel diode known as the Asymmetrical Spacer Layer Tunnel (ASPAT). The term rectenna is an abbreviation for a rectifying antenna, a device with a rectifier and antenna coexisting as a single design. The ASPAT is the centrepiece of the rectifier used for its strong temperature independence, zero bias, and high dynamic range. The antenna is designed to be impedance matched with the rectifier, eliminating the need for a matching network and saving valuable real estate on the gallium arsenide (GaAs) substrate. The antenna is fully integrated with the rectifier on a single chip, thus enabling antenna miniaturisation due to the high dielectric constant of GaAs and spiral design. This miniaturisation enables the design to be fabricated economically on a GaAs substrate whilst being comparable in size to a 15-gauge needle, thus unlocking applications in medical implants. The design presented here has a total die size of 4 × 1.2 mm2, with a maximum measured output voltage of 0.97 V and a 20 dBm single-tone 2.35 GHz signal transmitted 5 cm away from the rectenna.
Collapse
Affiliation(s)
- Christopher Walsh
- Department of Electrical and Electronic Engineering, University of Manchester, Manchester M13 9PL, UK
| | - Saad G Muttlak
- Department of Electrical and Electronic Engineering, University of Manchester, Manchester M13 9PL, UK
| | | | - Mohamed Missous
- Department of Electrical and Electronic Engineering, University of Manchester, Manchester M13 9PL, UK
| |
Collapse
|
6
|
Kavitha R. Analysis of Impact of Bioimpedance on Performance of Implant coil of Artificial Retina for Optimizing Q factor & Bandwidth. IEEE TRANSACTIONS ON BIOMEDICAL CIRCUITS AND SYSTEMS 2022; PP:142-151. [PMID: 37015408 DOI: 10.1109/tbcas.2022.3229669] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/19/2023]
Abstract
Spiral coils are indispensable part of implantable electronics for facilitating wireless power and data transfer. Although many advanced high Q receiver design have emerged, implementing and retaining high Q in biological medium so as to improve link efficiency is challenging. This article bridges the gap between advanced techniques towards improving link efficiency and the tissue losses that deteriorates the Q factor of coil in heterogeneous tissue medium. The purpose of this research is to improve the Q factor and bandwidth of the coil in tissue medium by reducing the net conductance of the coil in tissue medium, which is comparable to the net conductance in air. Bioimpedance of each layer of the eye is modelled to identify the highly capacitive and highly conductive tissue layer in the eye. To investigate the worst-case and best-case scenario, Q factor and bandwidth of the implant coil is analysed in the eye with and without aqueous humor which is a highly conductive and capacitive tissue layer in the eye. The coil is encapsulated with breast fat which possess lowest permittivity of all body tissue. After removing the high conductive tissue layer from the implantation zone, the Q factor and bandwidth of the coil is improved by 87.5 % and 97.7 % respectively. It is observed that 100 % Q at 10 MHz and 76.75 % of bandwidth is recovered in tissue medium after using breast fat as encapsulation layer. This demonstration of coil for various test cases in tissue medium aids to device a reliable, safe and efficient wireless power/data transfer system for artificial retina.
Collapse
|
7
|
Yousefi T, Timonina K, Zoidl G, Kassiri H. An Implantable Optogenetic Neuro-Stimulator SoC With Extended Optical Pulse-Width Enabled by Supply-Variation-Immune Cycled Light-Toggling Stimulation. IEEE TRANSACTIONS ON BIOMEDICAL CIRCUITS AND SYSTEMS 2022; 16:557-569. [PMID: 35969561 DOI: 10.1109/tbcas.2022.3198911] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/15/2023]
Abstract
The design, development, and experimental validation of an inductively-powered four-channel optical neuro-stimulator system on a chip (SoC) with on-chip neural recording, temperature monitoring, signal processing, and bidirectional wireless data communication are presented. A biologically-inspired optical stimulation approach is employed that extends the limitations on the stimulation pulse-width and frequency (i.e., enabling wirelessly-powered optical stimulation at very low frequencies (e.g., 10 Hz)) while significantly reducing the required on-device storage capacitor size. The biological efficacy of the proposed approach is validated and compared with conventional stimulation through in vitro experiments. The stimulator's energy efficiency is enhanced by employing a high-gain (850 A/A) current amplifier/driver in each channel that steers up to 10 mA into the optical source with an excellent linearity ( 0.5LSB), while 1) yielding the lowest-in-literature required voltage headroom, and 2) being insensitive to large (up to 12%) supply voltage drops, which is ideal for battery-less implantable devices. Additionally, to maximize the percentage of the generated optical power that reaches the targeted cells (thus, further energy efficiency enhancement), inkjet printing is utilized to fabricate custom-designed optical μlenses that are placed directly on top of the silicon SoC to enhance the generated light's directivity by > 30×. An electrophysiological recording channel for real-time monitoring of the stimulation efficacy and a high-precision (0.1 °C resolution) temperature readout circuit for shutting off stimulation upon detection of an unsafe temperature increase are also integrated on the chip. Additionally, the SoC hosts an ASK receiver and an LSK transmitter for downlink and uplink wireless data communication, respectively. The SoC is fabricated in a standard 130 nm CMOS process and occupies 6 mm 2. Measurement results for different sensory and communication blocks are presented, as well as in vitro experimental validation results showing simultaneous optical stimulation, electrical recording, and calcium imaging.
Collapse
|
8
|
Yu Z, Chen JC, He Y, Alrashdan FT, Avants BW, Singer A, Robinson JT, Yang K. Magnetoelectric Bio-Implants Powered and Programmed by a Single Transmitter for Coordinated Multisite Stimulation. IEEE JOURNAL OF SOLID-STATE CIRCUITS 2022; 57:818-830. [PMID: 36275505 PMCID: PMC9581110 DOI: 10.1109/jssc.2021.3129993] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.5] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/16/2023]
Abstract
This paper presents a hardware platform including stimulating implants wirelessly powered and controlled by a shared transmitter for coordinated leadless multisite stimulation. The adopted novel single-transmitter, multiple-implant structure can flexibly deploy stimuli, improve system efficiency, easily scale stimulating channel quantity and relieve efforts in device synchronization. In the proposed system, a wireless link leveraging magnetoelectric effects is co-designed with a robust and efficient system-on-chip to enable reliable operation and individual programming of every implant. Each implant integrates a 0.8-mm2 chip, a 6-mm2 magnetoelectric film, and an energy storage capacitor within a 6.2-mm3 size. Magnetoelectric power transfer is capable of safely transmitting milliwatt power to devices placed several centimeters away from the transmitter coil, maintaining good efficiency with size constraints and tolerating 60-degree, 1.5-cm misalignment in angular and lateral movement. The SoC robustly operates with 2-V source amplitude variations that spans a 40-mm transmitter-implant distance change, realizes individual addressability through physical unclonable function IDs, and achieves 90% efficiency for 1.5-to-3.5-V stimulation with fully programmable stimulation parameters.
Collapse
Affiliation(s)
| | | | - Yan He
- Rice University, Houston, TX 77005, USA
| | | | | | | | - Jacob T Robinson
- Rice University, Houston, TX 77005, USA; Baylor College of Medicine, Houston, TX 77030, USA
| | | |
Collapse
|
9
|
Nasrollahpour M, Zaeimbashi M, Khalifa A, Liang X, Chen H, Sun N, Abrishami SMS, Martos-Repath I, Emam S, Cash S, Sun NX. Magnetoelectric (ME) Antenna for On-chip Implantable Energy Harvesting. ANNUAL INTERNATIONAL CONFERENCE OF THE IEEE ENGINEERING IN MEDICINE AND BIOLOGY SOCIETY. IEEE ENGINEERING IN MEDICINE AND BIOLOGY SOCIETY. ANNUAL INTERNATIONAL CONFERENCE 2021; 2021:6167-6170. [PMID: 34892524 DOI: 10.1109/embc46164.2021.9629823] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/14/2023]
Abstract
A novel magnetoelectric (ME) antenna is fabricated to be integrated to the on-chip energy harvesting circuit for brain-computer interface applications. The proposed ME antenna resonates at the frequency of 2.57 GHz while providing a bandwidth of 3.37 MHz. The proposed rectangular ME antenna wireless power transfer efficiency is 0.304 %, which is considerably higher than that of micro-coils.Clinical Relevance- This provides a suitable energy harvesting efficiency for wirelessly powering up the brain implant devices.
Collapse
|
10
|
Ultra-compact dual-band smart NEMS magnetoelectric antennas for simultaneous wireless energy harvesting and magnetic field sensing. Nat Commun 2021; 12:3141. [PMID: 34035237 PMCID: PMC8149822 DOI: 10.1038/s41467-021-23256-z] [Citation(s) in RCA: 32] [Impact Index Per Article: 10.7] [Reference Citation Analysis] [Abstract] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 04/18/2020] [Accepted: 04/13/2021] [Indexed: 11/12/2022] Open
Abstract
Ultra-compact wireless implantable medical devices are in great demand for healthcare applications, in particular for neural recording and stimulation. Current implantable technologies based on miniaturized micro-coils suffer from low wireless power transfer efficiency (PTE) and are not always compliant with the specific absorption rate imposed by the Federal Communications Commission. Moreover, current implantable devices are reliant on differential recording of voltage or current across space and require direct contact between electrode and tissue. Here, we show an ultra-compact dual-band smart nanoelectromechanical systems magnetoelectric (ME) antenna with a size of 250 × 174 µm2 that can efficiently perform wireless energy harvesting and sense ultra-small magnetic fields. The proposed ME antenna has a wireless PTE 1–2 orders of magnitude higher than any other reported miniaturized micro-coil, allowing the wireless IMDs to be compliant with the SAR limit. Furthermore, the antenna’s magnetic field detectivity of 300–500 pT allows the IMDs to record neural magnetic fields. Wireless implantable medical devices (IMDs) are hamstrung by both size and efficiency required for wireless power transfer. Here, Zaeimbashi et al. present a magnetoelectric nano-electromechanical systems that can harvest energy and sense weak magnetic fields like those arising from neural activity.
Collapse
|
11
|
Kim C, Nichols E, Kim BN. Choosing the Optimal Power Coils Using Open-Source k-Oriented Design Automation. IEEE TRANSACTIONS ON BIOMEDICAL CIRCUITS AND SYSTEMS 2021; 15:159-170. [PMID: 33729948 DOI: 10.1109/tbcas.2021.3059934] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/12/2023]
Abstract
Wireless power coils have found important use in implantable medical devices for safe and reliable wireless power transfer. Designing coils for each specific application is a complex process with many interdependent design variables; determining the most optimal design parameters for each pair is challenging and time-consuming. In this paper, we develop an automated design method for planar square-spiral coils that generates the idealized design parameters for maximum power transfer efficiency according to the input design requirements. Computational complexity is first reduced by isolating the inductive coupling coefficient, k, from other design parameters. A simplified but accurate equivalent circuit model is then developed, where skin effect, proximity effect, and parasitic capacitive coupling are iteratively considered. The proposed method is implemented in an open-source software which accounts for the input fabrication limitations and application specific requirements. The accuracy of the estimated power transfer efficiency is validated via finite element method simulation. Using the presented approach, the coil design process is fully automated and can be done in few minutes.
Collapse
|
12
|
Abstract
Wireless power transmission (WPT) is a critical technology that provides an alternative for wireless power and communication with implantable medical devices (IMDs). This article provides a study concentrating on popular WPT techniques for IMDs including inductive coupling, microwave, ultrasound, and hybrid wireless power transmission (HWPT) systems. Moreover, an overview of the major works is analyzed with a comparison of the symmetric and asymmetric design elements, operating frequency, distance, efficiency, and harvested power. In general, with respect to the operating frequency, it is concluded that the ultrasound-based and inductive-based WPTs have a low operating frequency of less than 50 MHz, whereas the microwave-based WPT works at a higher frequency. Moreover, it can be seen that most of the implanted receiver’s dimension is less than 30 mm for all the WPT-based methods. Furthermore, the HWPT system has a larger receiver size compared to the other methods used. In terms of efficiency, the maximum power transfer efficiency is conducted via inductive-based WPT at 95%, compared to the achievable frequencies of 78%, 50%, and 17% for microwave-based, ultrasound-based, and hybrid WPT, respectively. In general, the inductive coupling tactic is mostly employed for transmission of energy to neuro-stimulators, and the ultrasonic method is used for deep-seated implants.
Collapse
|
13
|
Yousefi T, Taghadosi M, Dabbaghian A, Siu R, Grau G, Zoidl G, Kassiri H. An Energy-Efficient Optically-Enhanced Highly-Linear Implantable Wirelessly-Powered Bidirectional Optogenetic Neuro-Stimulator. IEEE TRANSACTIONS ON BIOMEDICAL CIRCUITS AND SYSTEMS 2020; 14:1274-1286. [PMID: 32976106 DOI: 10.1109/tbcas.2020.3026937] [Citation(s) in RCA: 2] [Impact Index Per Article: 0.5] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/11/2023]
Abstract
This paper presents an energy-efficient mm-scale self-contained bidirectional optogenetic neuro-stimulator, which employs a novel highly-linear μLED driving circuit architecture as well as inkjet-printed custom-designed optical μlenses for light directivity enhancement. The proposed current-mode μLED driver performs linear control of optical stimulation for the entire target range ( 10 mA) while requiring the smallest reported headroom, yielding a significant boost in the energy conversion efficiency. A 30.46× improvement in the power delivery efficiency to the target tissue is achieved by employing a pair of printed optical μlenses. The fabricated SoC also integrates two recording channels for LFP recording and digitization, as well as power management blocks. A micro-coil is also embedded on the chip to receive inductive power and our experimental results show a PTE of 2.24 % for the wireless link. The self-contained system including the μLEDs, μlenses and the capacitors required by the power management blocks is sized 6 mm 3 and weighs 12.5 mg. Full experimental measurement results for electrical and optical circuitry as well as in vitro measurement results are reported.
Collapse
|
14
|
Kim C, Park J, Ha S, Akinin A, Kubendran R, Mercier PP, Cauwenberghs G. A 3 mm × 3 mm Fully Integrated Wireless Power Receiver and Neural Interface System-on-Chip. IEEE TRANSACTIONS ON BIOMEDICAL CIRCUITS AND SYSTEMS 2019; 13:1736-1746. [PMID: 31581095 DOI: 10.1109/tbcas.2019.2943506] [Citation(s) in RCA: 16] [Impact Index Per Article: 3.2] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/10/2023]
Abstract
A miniaturized, fully integrated wireless power receiver system-on-chip with embedded 16-channel electrode array and data transceiver for electrocortical neural recording and stimulation is presented. An H-tree power and signal distribution network throughout the SoC maintains high quality factor up to 11 in the on-chip receiver coil at 144 MHz resonant frequency while rejecting RF interference in sensitive neural interface circuits owing to its perpendicular and equidistant geometry. A multi-mode buck-boost resonant regulating rectifier (B 2R 3) offers greater than 11-dB input dynamic range in RF reception and less than 1 mV overshoot in transient load regulation. At 10 mm link distance, the 9 mm 2 neural interface SoC fabricated in a 180 nm silicon-on-insulator (SOI) process attains an overall wireless power transmission system efficiency (WSE) of 3.4% in driving a 160 μW load yielding a WSE figure-of-merit of 131, while maintaining signal integrity in analog recording and wireless data transmission that comprise the on-chip load.
Collapse
|
15
|
Khalifa A, Liu Y, Karimi Y, Wang Q, Eisape A, Stanacevic M, Thakor N, Bao Z, Etienne-Cummings R. The Microbead: A 0.009 mm 3 Implantable Wireless Neural Stimulator. IEEE TRANSACTIONS ON BIOMEDICAL CIRCUITS AND SYSTEMS 2019; 13:971-985. [PMID: 31484132 DOI: 10.1109/tbcas.2019.2939014] [Citation(s) in RCA: 46] [Impact Index Per Article: 9.2] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 05/28/2023]
Abstract
Wirelessly powered implants are increasingly being developed to interface with neurons in the brain. They often rely on microelectrode arrays, which are limited by their ability to cover large cortical surface areas and long-term stability because of their physical size and rigid configuration. Yet some clinical and research applications prioritize a distributed neural interface over one that offers high channel count. One solution to make large scale, fully specifiable, electrical stimulation/recording possible, is to disconnect the electrodes from the base, so that they can be arbitrarily placed freely in the nervous system. In this work, a wirelessly powered stimulating implant is miniaturized using a novel electrode integration technique, and its implanted depth maximized using new optimization design methods for the transmitter and receiver coils. The stimulating device is implemented in a 130 nm CMOS technology with the following characteristics: 300 μm × 300 μm × 80 μm size; optimized two-coil inductive link; and integrated circuit, electrodes and coil. The wireless and stimulation capability of the implant is demonstrated in a conductive medium, as well as in-vivo. To the best of our knowledge, the fabricated free-floating miniaturized implant has the best depth-to-volume ratio making it an excellent tool for minimally-invasive distributed neural interface, and thus could eventually complement or replace the rigid arrays that are currently the state-of-the-art in brain set-ups.
Collapse
|
16
|
Zaeimbashi M, Lin H, Dong C, Liang X, Nasrollahpour M, Chen H, Sun N, Matyushov A, He Y, Wang X, Tu C, Wei Y, Zhang Y, Cash SS, Onabajo M, Shrivastava A, Sun N. NanoNeuroRFID: A Wireless Implantable Device Based on Magnetoelectric Antennas. ACTA ACUST UNITED AC 2019. [DOI: 10.1109/jerm.2019.2903930] [Citation(s) in RCA: 43] [Impact Index Per Article: 8.6] [Reference Citation Analysis] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/10/2022]
|
17
|
Miarnaeimi M, Ghalibafan J, Hashemi SM. A modified magnetic resonance wireless power transfer system for capsule endoscopy. Electromagn Biol Med 2019; 38:158-167. [PMID: 30873888 DOI: 10.1080/15368378.2019.1591440] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 10/27/2022]
Abstract
BACKGROUND The current study presents a fully planar wireless power transfer (WPT) scheme with the aim of providing enough power for capsule endoscopy performance. The method's implementation on patients is more convenient than that of the previous conventional WPT plans in which a cylindrical wire coil is placed around the patient's body. In addition to this, while using the present printed power receiver structure, the capsule's internal space of opens up for other components such as the image sensors and data transmitting components. To improve the efficiency, a two-layer printed coil has been used as the transmitter, a two-layer printed coil as the receiver and a power coil on the transmitter side excited at 13.56 MHz. RESULTS Applying this method, the efficiency has increased to more than 2% for the proposed structure. Moreover, the effect of the body tissue on power efficiency has been simulated and measured and the maximum specific absorption rate (SAR) value considered for the desired system. CONCLUSIONS The obtained results indicate that the proposed system meets the medical standards requirements.
Collapse
Affiliation(s)
- Masoumeh Miarnaeimi
- a Faculty of Electrical Engineering and Robotic , Shahrood University of Technology , Shahrood , Iran
| | - Javad Ghalibafan
- a Faculty of Electrical Engineering and Robotic , Shahrood University of Technology , Shahrood , Iran
| | - Seyed Mohammad Hashemi
- b Department of Electrical Engineering , Shahid Rajaee Teacher Training University , Tehran , Iran
| |
Collapse
|
18
|
Moore J, Castellanos S, Xu S, Wood B, Ren H, Tse ZTH. Applications of Wireless Power Transfer in Medicine: State-of-the-Art Reviews. Ann Biomed Eng 2018; 47:22-38. [PMID: 30306381 DOI: 10.1007/s10439-018-02142-8] [Citation(s) in RCA: 13] [Impact Index Per Article: 2.2] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 04/24/2018] [Accepted: 09/24/2018] [Indexed: 12/17/2022]
Abstract
Magnetic resonance within the field of wireless power transfer has seen an increase in popularity over the past decades. This rise can be attributed to the technological advances of electronics and the increased efficiency of popular battery technologies. The same principles of electromagnetic theory can be applied to the medical field. Several medical devices intended for use inside the body use batteries and electrical circuits that could be powered wirelessly. Other medical devices limit the mobility or make patients uncomfortable while in use. The fundamental theory of electromagnetics can improve the field by solving some of these problems. This survey paper summarizes the recent uses and discoveries of wireless power in the medical field. A comprehensive search for papers was conducted using engineering search engines and included papers from related conferences. During the initial search, 247 papers were found then non-relevant papers were eliminated to leave only suitable material. Seventeen relevant journal papers and/or conference papers were found, then separated into defined categories: Implants, Pumps, Ultrasound Imaging, and Gastrointestinal (GI) Endoscopy. The approach and methods for each paper were analyzed and compared yielding a comprehensive review of these state of the art technologies.
Collapse
Affiliation(s)
- Julian Moore
- School of Electrical and Computer Engineering, The University of Georgia, Athens, GA, 30602, USA
| | - Sharon Castellanos
- School of Electrical and Computer Engineering, The University of Georgia, Athens, GA, 30602, USA
| | - Sheng Xu
- Center for Interventional Oncology, Radiology and Imaging Sciences, NIH Clinical Center, National Institute of Biomedical Imaging and Bioengineering & National Cancer Institute Center for Cancer Research, National Institutes of Health, Bethesda, MD, USA
| | - Bradford Wood
- Center for Interventional Oncology, Radiology and Imaging Sciences, NIH Clinical Center, National Institute of Biomedical Imaging and Bioengineering & National Cancer Institute Center for Cancer Research, National Institutes of Health, Bethesda, MD, USA
| | - Hongliang Ren
- Department of Biomedical Engineering, National University of Singapore, Singapore, 119077, Singapore
| | - Zion Tsz Ho Tse
- School of Electrical and Computer Engineering, The University of Georgia, Athens, GA, 30602, USA.
| |
Collapse
|
19
|
Feng P, Yeon P, Cheng Y, Ghovanloo M, Constandinou TG. Chip-Scale Coils for Millimeter-Sized Bio-Implants. IEEE TRANSACTIONS ON BIOMEDICAL CIRCUITS AND SYSTEMS 2018; 12:1088-1099. [PMID: 30040662 DOI: 10.1109/tbcas.2018.2853670] [Citation(s) in RCA: 5] [Impact Index Per Article: 0.8] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/08/2023]
Abstract
Next generation implantable neural interfaces are targeting devices with mm-scale form factors that are freely floating and completely wireless. Scalability to more recording (or stimulation) channels will be achieved through distributing multiple devices, instead of the current approach that uses a single centralized implant wired to individual electrodes or arrays. In this way, challenges associated with tethers, micromotion, and reliability of wiring is mitigated. This concept is now being applied to both central and peripheral nervous system interfaces. One key requirement, however, is to maximize specific absorption rate (SAR) constrained achievable wireless power transfer efficiency (PTE) of these inductive links with mm-sized receivers. Chip-scale coil structures for microsystem integration that can provide efficient near-field coupling are investigated. We develop near-optimal geometries for three specific coil structures: in-CMOS, above-CMOS (planar coil post-fabricated on a substrate), and around-CMOS (helical wirewound coil around substrate). We develop analytical and simulation models that have been validated in air and biological tissues by fabrications and experimental measurements. Specifically, we prototype structures that are constrained to a 4 mm 4 mm silicon substrate, i.e., the planar in-/above-CMOS coils have outer diameters 4 mm, whereas the around-CMOS coil has an inner diameter of 4 mm. The in-CMOS and above-CMOS coils have metal film thicknesses of 3- m aluminium and 25- m gold, respectively, whereas the around-CMOS coil is fabricated by winding a 25-m gold bonding wire around the substrate. The measured quality factors (Q) of the mm-scale Rx coils are 10.5 @450.3 MHz (in-CMOS), 24.61 @85 MHz (above-CMOS), and 26.23 @283 MHz (around-CMOS). Also, PTE of 2-coil links based on three types of chip-scale coils is measured in air and tissue environment to demonstrate tissue loss for bio-implants. The SAR-constrained maximum PTE measured (together with resonant frequencies, in tissue) are 1.64% @355.8 MHz (in-CMOS), 2.09% @82.9 MHz (above-CMOS), and 3.05% @318.8 MHz (around-CMOS).
Collapse
|
20
|
Giagka V, Serdijn WA. Realizing flexible bioelectronic medicines for accessing the peripheral nerves - technology considerations. Bioelectron Med 2018; 4:8. [PMID: 32232084 PMCID: PMC7098212 DOI: 10.1186/s42234-018-0010-y] [Citation(s) in RCA: 25] [Impact Index Per Article: 4.2] [Reference Citation Analysis] [Abstract] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 02/22/2018] [Accepted: 06/13/2018] [Indexed: 11/13/2022] Open
Abstract
Patients suffering from conditions such as paralysis, diabetes or rheumatoid arthritis could in the future be treated in a personalised manner using bioelectronic medicines (BEms) (Nat Rev Drug Discov 13:399–400, 2013, Proc Natl Acad Sci USA 113:8284–9, 2016, J Intern Med 282:37–45, 2017). To deliver this personalised therapy based on electricity, BEms need to target various sites in the human body and operate in a closed-loop manner. The specific conditions and anatomy of the targeted sites pose unique challenges in the development of BEms. With a focus on BEms based on flexible substrates for accessing small peripheral nerves, this paper discusses several system-level technology considerations related to the development of such devices. The focus is mainly on miniaturisation and long-term operation. We present an overview of common substrate and electrode materials, related processing methods, and discuss assembly, miniaturisation and long-term stability issues.
Collapse
Affiliation(s)
- Vasiliki Giagka
- 1Section Bioelectronics, Department of Electrical Engineering, Mathematics and Computer Science, Delft University of Technology, Delft, The Netherlands.,2Technologies for Bioelectronics Group, Department of System Integration and Interconnection Technologies, Fraunhofer Institute for Reliability and Microintegration IZM, Berlin, Germany
| | - Wouter A Serdijn
- 1Section Bioelectronics, Department of Electrical Engineering, Mathematics and Computer Science, Delft University of Technology, Delft, The Netherlands
| |
Collapse
|
21
|
Khalifa A, Karimi Y, Wang Q, Garikapati S, Montlouis W, Stanacevic M, Thakor N, Etienne-Cummings R. The Microbead: A Highly Miniaturized Wirelessly Powered Implantable Neural Stimulating System. IEEE TRANSACTIONS ON BIOMEDICAL CIRCUITS AND SYSTEMS 2018; 12:521-531. [PMID: 29877816 DOI: 10.1109/tbcas.2018.2802443] [Citation(s) in RCA: 14] [Impact Index Per Article: 2.3] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 05/21/2023]
Abstract
An implant that can electrically stimulate neurons across different depths and regions of the brain currently does not exist as it poses a number of obstacles that need to be solved. In order to address the challenges, this paper presents the concept of "microbead," a fully integrated wirelessly powered neural device that allows for spatially selective activation of neural tissue. The prototype chip is fabricated in 130-nm CMOS technology and currently measures 200 μm × 200 μm, which represents the smallest remotely powered stimulator to date. The system is validated experimentally in a rat by stimulating the sciatic nerve with 195-μs current pulses. To power the ultrasmall on-silicon coil, 36-dBm source power is provided to a highly optimized transmitter (Tx) coil at a coupling distance of 5 mm. In order to satisfy the strict power limit for safe use in human subjects, a pulsed powering scheme is implemented that enables a significant decrease in the average power emitted from the Tx.
Collapse
|
22
|
Yeon P, Mirbozorgi SA, Lim J, Ghovanloo M. Feasibility Study on Active Back Telemetry and Power Transmission Through an Inductive Link for Millimeter-Sized Biomedical Implants. IEEE TRANSACTIONS ON BIOMEDICAL CIRCUITS AND SYSTEMS 2017; 11:1366-1376. [PMID: 29293426 DOI: 10.1109/tbcas.2017.2775638] [Citation(s) in RCA: 5] [Impact Index Per Article: 0.7] [Reference Citation Analysis] [Abstract] [MESH Headings] [Grants] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/07/2023]
Abstract
This paper presents a feasibility study of wireless power and data transmission through an inductive link to a 1-mm 2 implant, to be used as a free-floating neural probe, distributed across a brain area of interest. The proposed structure utilizes a four-coil inductive link for back telemetry, shared with a three-coil link for wireless power transmission. We propose a design procedure for geometrical optimization of the inductive link in terms of power transmission efficiency (PTE) considering specific absorption rate and data rate. We have designed a low-power pulse-based active data transmission circuit and characterized performance of the proposed inductive link in terms of its data rate and bit error rate (BER). The 1-mm2 data-Tx/power-Rx coil is implemented using insulated bonding wire with diameter, resulting in measured PTE in tissue media of 2.01% at 131 MHz and 1.8-cm coil separation distance when the resonator coil inner radius is 1 cm. The measured BER at 1-Mbps data rate was and in the air and tissue environments, respectively.
Collapse
|
23
|
Freeman DK, O'Brien JM, Kumar P, Daniels B, Irion RA, Shraytah L, Ingersoll BK, Magyar AP, Czarnecki A, Wheeler J, Coppeta JR, Abban MP, Gatzke R, Fried SI, Lee SW, Duwel AE, Bernstein JJ, Widge AS, Hernandez-Reynoso A, Kanneganti A, Romero-Ortega MI, Cogan SF. A Sub-millimeter, Inductively Powered Neural Stimulator. Front Neurosci 2017; 11:659. [PMID: 29230164 PMCID: PMC5712043 DOI: 10.3389/fnins.2017.00659] [Citation(s) in RCA: 40] [Impact Index Per Article: 5.7] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 07/14/2017] [Accepted: 11/10/2017] [Indexed: 01/02/2023] Open
Abstract
Wireless neural stimulators are being developed to address problems associated with traditional lead-based implants. However, designing wireless stimulators on the sub-millimeter scale (<1 mm3) is challenging. As device size shrinks, it becomes difficult to deliver sufficient wireless power to operate the device. Here, we present a sub-millimeter, inductively powered neural stimulator consisting only of a coil to receive power, a capacitor to tune the resonant frequency of the receiver, and a diode to rectify the radio-frequency signal to produce neural excitation. By replacing any complex receiver circuitry with a simple rectifier, we have reduced the required voltage levels that are needed to operate the device from 0.5 to 1 V (e.g., for CMOS) to ~0.25–0.5 V. This reduced voltage allows the use of smaller receive antennas for power, resulting in a device volume of 0.3–0.5 mm3. The device was encapsulated in epoxy, and successfully passed accelerated lifetime tests in 80°C saline for 2 weeks. We demonstrate a basic proof-of-concept using stimulation with tens of microamps of current delivered to the sciatic nerve in rat to produce a motor response.
Collapse
Affiliation(s)
| | | | | | | | | | | | | | | | | | | | | | | | | | - Shelley I Fried
- Department of Neurosurgery, Massachusetts General Hospital, Harvard Medical School, Boston, MA, United States
| | - Seung Woo Lee
- Department of Neurosurgery, Massachusetts General Hospital, Harvard Medical School, Boston, MA, United States
| | | | | | - Alik S Widge
- Department of Psychiatry, Massachusetts General Hospital, Harvard Medical School, Charlestown, MA, United States.,Picower Institute of Learning and Memory, Massachusetts Institute of Technology, Cambridge, MA, United States
| | | | - Aswini Kanneganti
- Department of Bioengineering, University of Texas, Richardson, TX, United States
| | | | - Stuart F Cogan
- Department of Bioengineering, University of Texas, Richardson, TX, United States
| |
Collapse
|
24
|
Mirbozorgi SA, Yeon P, Ghovanloo M. Robust Wireless Power Transmission to mm-Sized Free-Floating Distributed Implants. IEEE TRANSACTIONS ON BIOMEDICAL CIRCUITS AND SYSTEMS 2017; 11:692-702. [PMID: 28504947 DOI: 10.1109/tbcas.2017.2663358] [Citation(s) in RCA: 13] [Impact Index Per Article: 1.9] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 05/10/2023]
Abstract
This paper presents an inductive link for wireless power transmission (WPT) to mm-sized free-floating implants (FFIs) distributed in a large three-dimensional space in the neural tissue that is insensitive to the exact location of the receiver (Rx). The proposed structure utilizes a high-Q resonator on the target wirelessly powered plane that encompasses randomly positioned multiple FFIs, all powered by a large external transmitter (Tx). Based on resonant WPT fundamentals, we have devised a detailed method for optimization of the FFIs and explored design strategies and safety concerns, such as coil segmentation and specific absorption rate limits using realistic finite element simulation models in HFSS including head tissue layers, respectively. We have built several FFI prototypes to conduct accurate measurements and to characterize the performance of the proposed WPT method. Measurement results on 1-mm receivers operating at 60 MHz show power transfer efficiency and power delivered to the load at 2.4% and 1.3 mW, respectively, within 14-18 mm of Tx-Rx separation and 7 cm2 of brain surface.
Collapse
|
25
|
Agarwal K, Jegadeesan R, Guo YX, Thakor NV. Wireless Power Transfer Strategies for Implantable Bioelectronics. IEEE Rev Biomed Eng 2017; 10:136-161. [PMID: 28328511 DOI: 10.1109/rbme.2017.2683520] [Citation(s) in RCA: 85] [Impact Index Per Article: 12.1] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 11/06/2022]
Abstract
Neural implants have emerged over the last decade as highly effective solutions for the treatment of dysfunctions and disorders of the nervous system. These implants establish a direct, often bidirectional, interface to the nervous system, both sensing neural signals and providing therapeutic treatments. As a result of the technological progress and successful clinical demonstrations, completely implantable solutions have become a reality and are now commercially available for the treatment of various functional disorders. Central to this development is the wireless power transfer (WPT) that has enabled implantable medical devices (IMDs) to function for extended durations in mobile subjects. In this review, we present the theory, link design, and challenges, along with their probable solutions for the traditional near-field resonant inductively coupled WPT, capacitively coupled short-ranged WPT, and more recently developed ultrasonic, mid-field, and far-field coupled WPT technologies for implantable applications. A comparison of various power transfer methods based on their power budgets and WPT range follows. Power requirements of specific implants like cochlear, retinal, cortical, and peripheral are also considered and currently available IMD solutions are discussed. Patient's safety concerns with respect to electrical, biological, physical, electromagnetic interference, and cyber security from an implanted neurotech device are also explored in this review. Finally, we discuss and anticipate future developments that will enhance the capabilities of current-day wirelessly powered implants and make them more efficient and integrable with other electronic components in IMDs.
Collapse
|
26
|
Fomundam L, Lin J. Multi-layer low frequency tissue equivalent phantoms for noninvasive test of shallow implants and evaluating antenna-body interaction. ANNUAL INTERNATIONAL CONFERENCE OF THE IEEE ENGINEERING IN MEDICINE AND BIOLOGY SOCIETY. IEEE ENGINEERING IN MEDICINE AND BIOLOGY SOCIETY. ANNUAL INTERNATIONAL CONFERENCE 2016; 2016:2353-2356. [PMID: 28268798 DOI: 10.1109/embc.2016.7591202] [Citation(s) in RCA: 1] [Impact Index Per Article: 0.1] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/06/2023]
Abstract
In this work, a tissue equivalent compound phantom with dielectric properties equivalent to an average human body surface has been developed for a low frequency operating range of 30 MHz to 200 MHz. The compound phantom consists of skin, fat, and muscle layers respectively. The phantom is simple to fabricate with low cost components. A custom coaxial test fixture has been developed to characteristic phantom dielectric properties, which eliminates use of a specialized expensive dielectric measurement probe. The proposed composite phantom can be used as a noninvasive technique to evaluate shallow biomedical implants, antenna-body interaction, and specific absorption rate of tissue media.
Collapse
|
27
|
Soltani N, Aliroteh MS, Salam MT, Perez Velazquez JL, Genov R. Low-Radiation Cellular Inductive Powering of Rodent Wireless Brain Interfaces: Methodology and Design Guide. IEEE TRANSACTIONS ON BIOMEDICAL CIRCUITS AND SYSTEMS 2016; 10:920-932. [PMID: 26960227 DOI: 10.1109/tbcas.2015.2502840] [Citation(s) in RCA: 2] [Impact Index Per Article: 0.3] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/05/2023]
Abstract
This paper presents a general methodology of inductive power delivery in wireless chronic rodent electrophysiology applications. The focus is on such systems design considerations under the following key constraints: maximum power delivery under the allowable specific absorption rate (SAR), low cost and spatial scalability. The methodology includes inductive coil design considerations within a low-frequency ferrite-core-free power transfer link which includes a scalable coil-array power transmitter floor and a single-coil implanted or worn power receiver. A specific design example is presented that includes the concept of low-SAR cellular single-transmitter-coil powering through dynamic tracking of a magnet-less receiver spatial location. The transmitter coil instantaneous supply current is monitored using a small number of low-cost electronic components. A drop in its value indicates the proximity of the receiver due to the reflected impedance of the latter. Only the transmitter coil nearest to the receiver is activated. Operating at the low frequency of 1.5 MHz, the inductive powering floor delivers a maximum of 15.9 W below the IEEE C95 SAR limit, which is over three times greater than that in other recently reported designs. The power transfer efficiency of 39% and 13% at the nominal and maximum distances of 8 cm and 11 cm, respectively, is maintained.
Collapse
|
28
|
Rodriguez S, Ollmar S, Waqar M, Rusu A. A Batteryless Sensor ASIC for Implantable Bio-Impedance Applications. IEEE TRANSACTIONS ON BIOMEDICAL CIRCUITS AND SYSTEMS 2016; 10:533-544. [PMID: 26372646 DOI: 10.1109/tbcas.2015.2456242] [Citation(s) in RCA: 17] [Impact Index Per Article: 2.1] [Reference Citation Analysis] [Abstract] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Indexed: 06/05/2023]
Abstract
The measurement of the biological tissue's electrical impedance is an active research field that has attracted a lot of attention during the last decades. Bio-impedances are closely related to a large variety of physiological conditions; therefore, they are useful for diagnosis and monitoring in many medical applications. Measuring living tissues, however, is a challenging task that poses countless technical and practical problems, in particular if the tissues need to be measured under the skin. This paper presents a bio-impedance sensor ASIC targeting a battery-free, miniature size, implantable device, which performs accurate 4-point complex impedance extraction in the frequency range from 2 kHz to 2 MHz. The ASIC is fabricated in 150 nm CMOS, has a size of 1.22 mm × 1.22 mm and consumes 165 μA from a 1.8 V power supply. The ASIC is embedded in a prototype which communicates with, and is powered by an external reader device through inductive coupling. The prototype is validated by measuring the impedances of different combinations of discrete components, measuring the electrochemical impedance of physiological solution, and performing ex vivo measurements on animal organs. The proposed ASIC is able to extract complex impedances with around 1 Ω resolution; therefore enabling accurate wireless tissue measurements.
Collapse
|
29
|
Bocan KN, Sejdić E. Adaptive Transcutaneous Power Transfer to Implantable Devices: A State of the Art Review. SENSORS 2016; 16:s16030393. [PMID: 26999154 PMCID: PMC4813968 DOI: 10.3390/s16030393] [Citation(s) in RCA: 87] [Impact Index Per Article: 10.9] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Download PDF] [Figures] [Subscribe] [Scholar Register] [Received: 01/05/2016] [Revised: 02/26/2016] [Accepted: 03/11/2016] [Indexed: 11/16/2022]
Abstract
Wireless energy transfer is a broad research area that has recently become applicable to implantable medical devices. Wireless powering of and communication with implanted devices is possible through wireless transcutaneous energy transfer. However, designing wireless transcutaneous systems is complicated due to the variability of the environment. The focus of this review is on strategies to sense and adapt to environmental variations in wireless transcutaneous systems. Adaptive systems provide the ability to maintain performance in the face of both unpredictability (variation from expected parameters) and variability (changes over time). Current strategies in adaptive (or tunable) systems include sensing relevant metrics to evaluate the function of the system in its environment and adjusting control parameters according to sensed values through the use of tunable components. Some challenges of applying adaptive designs to implantable devices are challenges common to all implantable devices, including size and power reduction on the implant, efficiency of power transfer and safety related to energy absorption in tissue. Challenges specifically associated with adaptation include choosing relevant and accessible parameters to sense and adjust, minimizing the tuning time and complexity of control, utilizing feedback from the implanted device and coordinating adaptation at the transmitter and receiver.
Collapse
Affiliation(s)
- Kara N Bocan
- Department of Electrical and Computer Engineering, Swanson School of Engineering, University of Pittsburgh, Pittsburgh, PA 15213, USA.
| | - Ervin Sejdić
- Department of Electrical and Computer Engineering, Swanson School of Engineering, University of Pittsburgh, Pittsburgh, PA 15213, USA.
| |
Collapse
|