Signal-to-Noise Ratio Analysis of a Phase-Sensitive Voltmeter for Electrical Impedance Tomography

Analysis of electrode arrangements for brain stroke diagnosis via electrical impedance tomography through numerical computational models

Objective.Rapid stroke-type classification is crucial for improved prognosis. However, current methods for classification are time-consuming, require expensive equipment, and can only be used in the hospital. One method that has demonstrated promise in a rapid, low-cost, non-invasive approach to stroke diagnosis is electrical impedance tomography (EIT). While EIT for stroke diagnosis has been the topic of several studies in recent years, to date, the impact of electrode placements and arrangements has rarely been analyzed or tested and only in limited scenarios. Optimizing the location and choice of electrodes can have the potential to improve performance and reduce hardware cost and complexity and, most importantly, diagnosis time.Approach.In this study, we analyzed the impact of electrodes in realistic numerical models by (1) investigating the effect of individual electrodes on the resulting simulated EIT boundary measurements and (2) testing the performance of different electrode arrangements using a machine learning classification model.Main results.We found that, as expected, the electrodes deemed most significant in detecting stroke depend on the location of the electrode relative to the stroke lesion, as well as the role of the electrode. Despite this dependence, there are notable electrodes used in the models that are consistently considered to be the most significant across the various stroke lesion locations and various head models. Moreover, we demonstrate that a reduction in the number of electrodes used for the EIT measurements is possible, given that the electrodes are approximately evenly distributed.Significance.In this way, electrode arrangement and location are important variables to consider when improving stroke diagnosis methods using EIT.

A Point-Matching Method of Moment with Sparse Bayesian Learning Applied and Evaluated in Dynamic Lung Electrical Impedance Tomography

Dynamic lung imaging is a major application of Electrical Impedance Tomography (EIT) due to EIT's exceptional temporal resolution, low cost and absence of radiation. EIT however lacks in spatial resolution and the image reconstruction is very sensitive to mismatches between the actual object's and the reconstruction domain's geometries, as well as to the signal noise. The non-linear nature of the reconstruction problem may also be a concern, since the lungs' significant conductivity changes due to inhalation and exhalation. In this paper, a recently introduced method of moment is combined with a sparse Bayesian learning approach to address the non-linearity issue, provide robustness to the reconstruction problem and reduce image artefacts. To evaluate the proposed methodology, we construct three CT-based time-variant 3D thoracic structures including the basic thoracic tissues and considering 5 different breath states from end-expiration to end-inspiration. The Graz consensus reconstruction algorithm for EIT (GREIT), the correlation coefficient (CC), the root mean square error (RMSE) and the full-reference (FR) metrics are applied for the image quality assessment. Qualitative and quantitative comparison with traditional and more advanced reconstruction techniques reveals that the proposed method shows improved performance in the majority of cases and metrics. Finally, the approach is applied to single-breath online in-vivo data to qualitatively verify its applicability.

Evaluation of Thoracic Equivalent Multiport Circuits Using an Electrical Impedance Tomography Hardware Simulation Interface

Electrical impedance tomography is a low-cost, safe, and high temporal resolution medical imaging modality which finds extensive application in real-time thoracic impedance imaging. Thoracic impedance changes can reveal important information about the physiological condition of patients’ lungs. In this way, electrical impedance tomography can be a valuable tool for monitoring patients. However, this technique is very sensitive to measurement noise or possible minor signal errors, coming from either the hardware, the electrodes, or even particular biological signals. Thus, the design of a good performance electrical impedance tomography hardware setup which properly interacts with the tissue examined is both an essential and a challenging concept. In this paper, we adopt an extensive simulation approach, which combines the system’s analogue and digital hardware, along with equivalent circuits of 3D finite element models that represent thoracic cavities. Each thoracic finite element model is created in MATLAB based on existing CT images, while the tissues’ conductivity and permittivity values for a selected frequency are acquired from a database using Python. The model is transferred to a multiport RLC network, embedded in the system’s hardware which is simulated at LT SPICE. The voltage output data are transferred to MATLAB where the electrical impedance tomography signal sampling and digital processing is also simulated. Finally, image reconstructions are performed in MATLAB, using the EIDORS library tool and considering the signal noise levels and different electrode and signal sampling configurations (ADC bits, sampling frequency, number of taps).

Analysis, Simulation, and Development of a Low-Cost Fully Active-Electrode Bioimpedance Measurement Module

A low-cost 1 kHz–400 kHz operating frequency fully-active electrode bioimpedance measurement module, based on Howland current source, is presented in this paper. It includes a buffered positive feedback Howland current source, implemented with operational amplifiers, as well as an AD8421 instrumentation amplifier, for the differential voltage measurements. Each active electrode module can be connected to others, assembling a wearable active electrode module array. From this array, 2 electrodes can be selected to be driven from a THS413 fully differential amplifier, activating a mirrored Howland current source. This work performs a complete circuit analysis, verified with MATLAB and SPICE simulations of the current source’s transconductance and output impedance over the frequency range between 1 kHz and 1 MHz. Resistors’ tolerances, possible mismatches, and the operational amplifiers’ non-idealities are considered in both the analysis and simulations. A comparison study between four selected operational amplifiers (ADA4622, OPA2210, AD8034, and AD8672) is additionally performed. The module is also hardware-implemented and tested in the lab for all four operational amplifiers and the transconductance is measured for load resistors of 150 Ω, 660 Ω, and 1200 Ω. Measurements showed that, using the AD8034 operational amplifier, the current source’s transconductance remains constant for frequencies up to 400 KHz for a 150 Ω load and 250 kHz for a 1200 Ω load, while lower performance is achieved with the other 3 operational amplifiers. Finally, transient simulations and measurements are performed at the AD8421 output for bipolar measurements on the 3 aforementioned load resistor values.

An Imaged Based Method for Universal Performance Evaluation of Electrical Impedance Tomography Systems

This paper describes a simple and reproducible method for universal evaluation of the performance of electrical impedance tomography (EIT) systems using reconstructed images. To address the issues where common electrical parameters are not directly related to the quality of EIT images, based on objective full reference (FR) image quality assessment, the method provides a visually distinguishable hot colormap and two new FR metrics, the global and the more specific 'region of interest'. A passive 16 electrode EIT system using an application specific integrated circuit front-end was used to evaluate the proposed method. The measured results show, both visually and in terms of the proposed FR metrics, the impact on recorded EIT images with different design parameters and non-idealities. The paper also compares the image results of a passive electrode system with a matched 'single variable' active electrode system and demonstrates the merit of an active electrode system for noise interference. A figure of merit based on the FR metrics is proposed.

A 1 MHz Miniaturized Electrical Impedance Tomography System for Prostate Imaging

An ASIC for a high frequency electrical impedance tomography (EIT) imaging system for prostate cancer screening is presented. The ASIC enables a small form-factor architecture, which ensures high signal-to-noise ratio (SNR) at MHz frequencies. The 4-channel ASIC was designed and fabricated in a standard CMOS 0.18- μm technology and integrates a novel current driver for current stimulus, instrumentation amplifier to interface with the tissue, VGA to provide variable gain and ADC with SPI interface for digitization. A prototype miniaturized EIT system was built and it was evaluated using a model transrectal imaging probe immersed into a tank filled with saline and a metal inclusion that demonstrated the open-domain problem of imaging prostate cancer lesion. The system maintained an SNR between 66 and 76 dB over the frequency range of 500 Hz to 1 MHz. Also, it produced reconstructed EIT images that depicted the presence of the small metal inclusion that modeled a prostate cancer imaging application.

Structured Design Methodology to Achieve a High SNR Electrical Impedance Tomography

In this paper, we present a methodology for designing the main circuit building blocks of an electrical impedance tomography (EIT) system. In particular, we derive equations that map system-level EIT specifications to the performance requirements of each circuit block. We also review the circuit architectures that are best suited for meeting a given set of performance requirements. Our proposed design methodology is focused on maximizing the EIT system's signal-to-noise ratio while minimizing total power consumption.

An Analog Front End ASIC for Cardiac Electrical Impedance Tomography

In this paper, an end-to-end CMOS application specific integrated circuit (ASIC) for readout channel in a cardiac electrical impedance tomography system is presented. The ASIC consists of an integrated current driver for current injection, an instrumentation amplifier, variable gain amplifier at the analog front end for voltage readout from electrodes, and an on-chip 10-bit successive approximation register analog to digital converter with serial peripheral interface. The ASIC is fabricated in the CMOS 0.18 $\mu$ m process with a supply voltage of 3.3 V. Amplitude and phase extraction of the voltages is performed in the digital domain with a matched filter. A fully integrated solution for use in multiple electrode system is demonstrated. The readout chain in the ASIC achieves a minimum signal-to-noise ratio of 71 dB over the frequency range of 500 Hz-700 kHz, while maintaining an average accuracy of 99.7 $\%$. Frame rates of 21 frames per second for a 32 electrode system is feasible, and the ASIC has an overall power consumption of 11.8 mW.

Amplitude demodulation for electrical capacitance tomography based on singular value decomposition

Amplitude demodulation is essential in image reconstruction for electrical capacitance tomography (ECT). In this paper, an amplitude demodulation method is proposed based on singular value decomposition (SVD), which can substitute the role of phase-sensitive demodulation in ECT. First, an M × N Hankel matrix is constructed based on a set of discrete samples. Then, SVD operation is performed on the matrix. Finally, the mathematical expression between the sinusoid amplitude and effective singular values is given; i.e., the first two singular values are used to estimate the amplitude information of the acquired signal. The proposed method has the following advantages: (1) since no reference signals are needed, the synchronization between the acquired and reference signals is not necessary; (2) this method can obtain the amplitude information of the acquired signal with a high signal-to-noise ratio (SNR), even in the case of non-integrity period sampling; and (3) SVD itself can also implement the filtering function; thus, no additional low-pass filters are required in the signal conditioning module. The demodulation accuracy and feasibility of the proposed method were verified by numerical simulations and experiments, indicating that it can provide amplitude demodulation with excellent SNR and robust performances.

A 10 MHz Read-Out Chain for Electrical Impedance Tomography

This paper presents the design and implementation of a read-out chain for electrical impedance tomography (EIT) imaging. The EIT imaging approach can be incorporated to take spectral images of the tissue under study, offering an affordable, portable device for home health monitoring. A fast read-out channel covering a wide range of frequencies is a must for such applications. The proposed read-out channel comprising a programmable gain instrumentation amplifier, an analog-to-digital converter (ADC), and an ADC driver is designed and fabricated in a 0.18  m CMOS technology. The proposed read-out chain operates over the wide frequency range of 100 Hz to 10 MHz, with an average signal-to-noise ratio of more than 60 dB. The entire read-out channel consumes between 6.9 and 21.8 mW, depending on its frequency of operation.