Characterization of Conductivity Changes During High-Frequency Irreversible Electroporation for Treatment Planning

Numerical simulation of neural excitation during brain tumor ablation by microsecond pulses

Replacing monopolar pulse with bipolar pulses of the same energized time can minimize unnecessary neurological side effects during irreversible electroporation (IRE). An improved neural excitation model that considers dynamic conductivity and thermal effects during brain tumor IRE ablation was proposed for the first time in this study. Nerve fiber excitation during IRE ablation by applying a monopolar pulse (100 μs) and a burst of bipolar pulses (energized time of 100 μs with both the sub-pulse length and interphase delay of 1 μs) was investigated. Our results suggest that both thermal effects and dynamic conductivity change the onset time of action potential (AP), and dynamic conductivity also changes the hyperpolarization amplitude. Considering both thermal effects and dynamic conductivity, the hyperpolarization amplitude in nerve fibers located 2 cm from the tumor center was reduced by approximately 23.8 mV and the onset time of AP was delayed by approximately 17.5 μs when a 500 V monopolar pulse was applied. Moreover, bipolar pulses decreased the excitable volume of brain tissue by approximately 68.8 % compared to monopolar pulse. Finally, bipolar pulses cause local excitation with lesser damage to surrounding healthy tissue in complete tumor ablation, demonstrating the potential benefits of bipolar pulses in brain tissue ablation.

Burst sine wave electroporation (B-SWE) for expansive blood-brain barrier disruption and controlled non-thermal tissue ablation for neurological disease

The blood-brain barrier (BBB) limits the efficacy of treatments for malignant brain tumors, necessitating innovative approaches to breach the barrier. This study introduces burst sine wave electroporation (B-SWE) as a strategic modality for controlled BBB disruption without extensive tissue ablation and compares it against conventional pulsed square wave electroporation-based technologies such as high-frequency irreversible electroporation (H-FIRE). Using an in vivo rodent model, B-SWE and H-FIRE effects on BBB disruption, tissue ablation, and neuromuscular contractions are compared. Equivalent waveforms were designed for direct comparison between the two pulsing schemes, revealing that B-SWE induces larger BBB disruption volumes while minimizing tissue ablation. While B-SWE exhibited heightened neuromuscular contractions when compared to equivalent H-FIRE waveforms, an additional low-dose B-SWE group demonstrated that a reduced potential can achieve similar levels of BBB disruption while minimizing neuromuscular contractions. Repair kinetics indicated faster closure post B-SWE-induced BBB disruption when compared to equivalent H-FIRE protocols, emphasizing B-SWE's transient and controllable nature. Additionally, finite element modeling illustrated the potential for extensive BBB disruption while reducing ablation using B-SWE. B-SWE presents a promising avenue for tailored BBB disruption with minimal tissue ablation, offering a nuanced approach for glioblastoma treatment and beyond.

Difference between endocardial and epicardial application of pulsed fields for targeting Epicardial Ganglia: An in-silico modelling study

BACKGROUND

Pulsed Field Ablation (PFA) has recently been proposed as a non-thermal energy to treat atrial fibrillation by selective ablation of ganglionated plexi (GP) embedded in epicardial fat. While some of PFA-technologies use an endocardial approach, others use epicardial access with promising pre-clinical results. However, as each technology uses a different and sometimes proprietary pulse application protocol, the comparation between endocardial vs. epicardial approach is almost impossible in experimental terms. For this reason, our study, based on a computational model, allows a direct comparison of electric field distribution and thermal-side effects of both approaches under equal conditions in terms of electrode design, pulse protocol and anatomical characteristics of the tissues involved.

METHODS

2D computational models with axial symmetry were built for endocardial and epicardial approaches. Atrial (1.5-2.5 mm) and fat (1-5 mm) thicknesses were varied to simulate a representative sample of what happens during PFA ablation for different applied voltage values (1000, 1500 and 2000 V) and number of pulses (30 and 50).

RESULTS

The epicardial approach was superior for capturing greater volumes of fat when the applied voltage was increased: 231 mm3/kV with the epicardial approach vs. 182 mm3/kV with the endocardial approach. In relation to collateral damage to the myocardium, the epicardial approach considerably spares the myocardium, unlike what happens with the endocardial approach. Although the epicardial approach caused much more thermal damage in the fat, there is not a significant difference between the approaches in terms of size of thermal damage in the myocardium.

CONCLUSIONS

Our results suggest that epicardial PFA ablation of GPs is more effective than an endocardial approach. The proximity and directionality of the electric field deposited using an epicardial approach are key to ensuring that higher electric field strengths and increased temperatures are obtained within the epicardial fat, thus contributing to selective ablation of the GPs with minimal myocardial damage.

Rapid estimation of electroporation-dependent tissue properties in canine lung tumors using a deep neural network

The efficiency of electroporation treatments depends on the application of a critical electric field over the targeted tissue volume. Both the electric field and temperature distribution strongly depend on the tissue-specific electrical properties, which both differ between patients in healthy and malignant tissues and change in an electric field-dependent manner from the electroporation process itself. Therefore, tissue property estimations are paramount for treatment planning with electroporation therapies. Ex vivo methods to find electrical tissue properties often misrepresent the targeted tissue, especially when translating results to tumors. A voltage ramp is an in situ method that applies a series of increasing electric potentials across treatment electrodes and measures the resulting current. Here, we develop a robust deep neural network, trained on finite element model simulations, to directly predict tissue properties from a measured voltage ramp. There was minimal test error (R2>0.94;p<0.0001) in three important electric tissue properties. Further, our model was validated to correctly predict the complete dynamic conductivity curve in a previously characterized ex vivo liver model (R2>0.93;p<0.0001) within 100 s from probe insertion, showing great utility for a clinical application. Lastly, we characterize the first reported electrical tissue properties of lung tumors from five canine patients (R2>0.99;p<0.0001). We believe this platform can be incorporated prior to treatment to quickly ascertain patient-specific tissue properties required for electroporation treatment planning models or real-time treatment prediction algorithms. Further, this method can be used over traditional ex vivo methods for in situ tissue characterization with clinically relevant geometries.

How intramyocardial fat can alter the electric field distribution during Pulsed Field Ablation (PFA): Qualitative findings from computer modeling

Even though the preliminary experimental data suggests that cardiac Pulsed Field Ablation (PFA) could be superior to radiofrequency ablation (RFA) in terms of being able to ablate the viable myocardium separated from the catheter by collagen and fat, as yet there is no formal physical-based analysis that describes the process by which fat can affect the electric field distribution. Our objective was thus to determine the electrical impact of intramyocardial fat during PFA by means of computer modeling. Computer models were built considering a PFA 3.5-mm blunt-tip catheter in contact with a 7-mm ventricular wall (with and without a scar) and a 2-mm epicardial fat layer. High voltage was set to obtain delivered currents of 19, 22 and 25 A. An electric field value of 1000 V/cm was considered as the lethal threshold. We found that the presence of fibrotic tissue in the scar seems to have a similar impact on the electric field distribution and lesion size to that of healthy myocardium only. However, intramyocardial fat considerably alters the electrical field distribution and the resulting lesion shape. The electric field tends to peak in zones with fat, even away from the ablation electrode, so that 'cold points' (i.e. low electric fields) appear around the fat at the current entry and exit points, while 'hot points' (high electric fields) occur in the lateral areas of the fat zones. The results show that intramyocardial fat can alter the electric field distribution and lesion size during PFA due to its much lower electrical conductivity than that of myocardium and fibrotic tissue.

Research frontiers of electroporation-based applications in cancer treatment: a bibliometric analysis

OBJECTIVES

Electroporation, the breakdown of the biomembrane induced by external electric fields, has increasingly become a research hotspot for its promising related methods in various kinds of cancers.

CONTENT

In this article, we utilized CiteSpace 6.1.R2 to perform a bibliometric analysis on the research foundation and frontier of electroporation-based applications in cancer therapy. A total of 3,966 bibliographic records were retrieved from the Web of Science Core Collection for the bibliometric analysis. Sersa G. and Mir L. M. are the most indispensable researchers in this field, and the University of Ljubljana of Slovenia is a prominent institution. By analyzing references and keywords, we found that, with a lower recurrence rate, fewer severe adverse events, and a higher success rate, irreversible electroporation, gene electrotransfer, and electrochemotherapy are the three main research directions that may influence the future treatment protocol of cancers.

SUMMARY

This article visualized relevant data to synthesize scientific research on electroporation-based cancer therapy, providing helpful suggestions for further investigations on electroporation.

OUTLOOK

Although electroporation-based technologies have been proven as promising tools for cancer treatment, its radical mechanism is still opaque and their commercialization and universalization need further efforts from peers.

Thermal damage map prediction during irreversible electroporation with U-Net

Recent developments in cancer treatment with irreversible electroporation (IRE) have led to a renewed interest in developing a treatment planning system based on Deep-Learning methods. This paper will give an account of U-Net, as a Deep-Learning architecture usage for predicting thermal damage area during IRE. In this study, an irregular shape of the liver tumor with MIMICS and 3-Matic software was created from Magnetic Resonance Imaging (MRI) images. To create electric field distribution and thermal damage maps in IRE, COMSOL Multiphysics 5.3 finite element analysis was performed. It was decided to use the pair needle, single bipolar, and multi-tine electrodes with different geometrical parameters as electrodes. The U-Net was designed as a Deep-Learning network to train and predict the thermal damage area from electric field distribution in the IRE. The average DICE coefficient and accuracy of trained U-Net for predicting thermal damage area on test data sets were 0.96 and 0.98, respectively, for the dataset consisting of all electrode type electric field intensity images. This is the first time that U-Net has been used to predict thermal damage area. The results of this research support the idea that the U-Net can be used for predicting thermal damage areas during IRE as a treatment planning system.

Determination of lethal electric field threshold for pulsed field ablation in ex vivo perfused porcine and human hearts

Introduction

Pulsed field ablation is an emerging modality for catheter-based cardiac ablation. The main mechanism of action is irreversible electroporation (IRE), a threshold-based phenomenon in which cells die after exposure to intense pulsed electric fields. Lethal electric field threshold for IRE is a tissue property that determines treatment feasibility and enables the development of new devices and therapeutic applications, but it is greatly dependent on the number of pulses and their duration.

Methods

In the study, lesions were generated by applying IRE in porcine and human left ventricles using a pair of parallel needle electrodes at different voltages (500-1500 V) and two different pulse waveforms: a proprietary biphasic waveform (Medtronic) and monophasic 48 × 100 μs pulses. The lethal electric field threshold, anisotropy ratio, and conductivity increase by electroporation were determined by numerical modeling, comparing the model outputs with segmented lesion images.

Results

The median threshold was 535 V/cm in porcine ((N = 51 lesions in n = 6 hearts) and 416 V/cm in the human donor hearts ((N = 21 lesions in n = 3 hearts) for the biphasic waveform. The median threshold value was 368 V/cm in porcine hearts ((N = 35 lesions in n = 9 hearts) cm for 48 × 100 μs pulses.

Discussion

The values obtained are compared with an extensive literature review of published lethal electric field thresholds in other tissues and were found to be lower than most other tissues, except for skeletal muscle. These findings, albeit preliminary, from a limited number of hearts suggest that treatments in humans with parameters optimized in pigs should result in equal or greater lesions.

PIRET-A Platform for Treatment Planning in Electroporation-Based Therapies

Tissue electroporation is the basis of several therapies. Electroporation is performed by briefly exposing tissues to high electric fields. It is generally accepted that electroporation is effective where an electric field magnitude threshold is overreached. However, it is difficult to preoperatively estimate the field distribution because it is highly dependent on anatomy and treatment parameters.

OBJECTIVE

We developed PIRET, a platform to predict the treatment volume in electroporation-based therapies.

METHODS

The platform seamlessly integrates tools to build patient-specific models where the electric field is simulated to predict the treatment volume. Patient anatomy is segmented from medical images and 3D reconstruction aids in placing the electrodes and setting up treatment parameters.

RESULTS

Four canine patients that had been treated with high-frequency irreversible electroporation were retrospectively planned with PIRET and with a workflow commonly used in previous studies, which uses different general-purpose segmentation (3D Slicer) and modeling software (3Matic and COMSOL Multiphysics). PIRET outperformed the other workflow by 65 minutes (× 1.7 faster), thanks to the improved user experience during treatment setup and model building. Both approaches computed similarly accurate electric field distributions, with average Dice scores higher than 0.93.

CONCLUSION

A platform which integrates all the required tools for electroporation treatment planning is presented. Treatment plan can be performed rapidly with minimal user interaction in a stand-alone platform.

SIGNIFICANCE

This platform is, to the best of our knowledge, the most complete software for treatment planning of irreversible electroporation. It can potentially be used for other electroporation applications.

Global sensitivity study for irreversible electroporation: Towards treatment planning under uncertainty

BACKGROUND

Electroporation-based cancer treatments are minimally invasive, nonthermal interventional techniques that leverage cell permeabilization to ablate the target tumor. However, the amount of permeabilization is susceptible to the numerous uncertainties during treatment, such as patient-specific variations in the tissue, type of the tumor, and the resolution of imaging equipment. These uncertainties can reduce the extent of ablation in the tissue, thereby affecting the effectiveness of the treatment.

PURPOSE

The aim of this work is to understand the effect of these treatment uncertainties on the treatment outcome for irreversible electroporation (IRE) in the case of colorectal liver metastasis (CRLM). Understanding the nature and extent of these effects can help us identify the influential treatment parameters and build better models for predicting the treatment outcome.

METHODS

This is an in silico study using a static computational model with a custom applicator design, spherical tissue, and tumor geometry. A nonlinear electrical conductivity, dependent on the local electric field, is considered. Morris analysis is used to identify the influential treatment parameters on the treatment outcome. Seven treatment parameters pertaining to the relative tumor location with respect to the applicator, the tumor growth pattern, and the electrical conductivity of tissue are analyzed. The treatment outcome is measured in terms of the relative tumor ablation with respect to the target ablation volume and total ablation volume.

RESULTS

The Morris analysis was performed with 800 model evaluations, sampled from the seven dimensional input parameter space. Electrical properties of the tissue, especially the electrical conductivity of the tumor before ablation, were found to be the most influential parameter for relative tumor ablation and total ablation volume. This parameter was found to be about 4-15 times more influential than the least influential parameter, depending on the tumor size. The tumor border configuration was identified as the least important parameter for treatment effectiveness. The most desired treatment outcome is obtained by a combination of high healthy liver conductivity and low tumor conductivity. This information can be used to tackle worst-case scenarios in treatment planning. Finally, when the safety margins used in the clinical applications are accounted for, the effects of uncertainties in the treatment parameters reduce drastically.

CONCLUSIONS

The results of this work can be used to create an efficient surrogate estimator for uncertainty quantification in the treatment outcome, that can be utilized in optimal real-time treatment planning solutions.

Automated irreversible electroporated region prediction using deep neural network, a preliminary study for treatment planning

The primary purpose of cancer treatment with irreversible electroporation (IRE) is to maximize tumor damage and minimize surrounding healthy tissue damage. Finite element analysis is one of the popular ways to calculate electric field and cell kill probability in IRE. However, this method also has limitations. This paper will focus on using a deep neural network (DNN) in IRE to predict irreversible electroporated regions for treatment planning purposes. COMSOL Multiphysics was used to simulate the IRE. The electric conductivity change during IRE was considered to create accurate data sets of electric field distribution and cell kill probability distributions. We used eight pulses with a pulse width of 100 μs, frequency of 1 Hz, and different voltages. To create masks for DNN training, a 90% cell kill probability contour was used. After data set creation, U-Net architecture was trained to predict irreversible electroporated regions. In this study, the average U-Net DICE coefficient on test data was 0.96. Also, the average accuracy of U-Net for predicting irreversible electroporated regions was 0.97. As far as we are aware, this is the first time that U-Net was used to predict an irreversible electroporated region in IRE. The present study provides significant evidence for U-Net's use for predicting an irreversible electroporated region in treatment planning.

Dynamic Impedance Analysis of Intestinal Anastomosis during High-Frequency Electric Field Welding Process

The success rate of the electrosurgical high-frequency electric field welding technique lies in reasonable control of the welding time. However, the final impedance value used to control the welding time varies due to differences in tissue size and the welding method during the welding process. This study aims to introduce a new reference indicator not limited by impedance size from dynamic impedance to achieve an adequate weld strength with minimal thermal damage, providing feedback on the tissue welding effect in medical power supplies. End-to-end anastomosis experiments were conducted with porcine small intestine tissue under seven levels of compression pressure. The dynamic impedance changes were analyzed, combined with compression pressure, temperature, moisture, and collagen during welding. The welding process was divided into three stages according to the dynamic impedance, with impedance decreasing in Period Ⅰ and impedance increasing in Period Ⅲ. Period Ⅲ was the key to high-strength connections due to water evaporation and collagen reorganization. The dynamic impedance ratio is defined as the final impedance divided by the minimum impedance, and successful welding would be predicted when detecting the dynamic impedance ratio over 4 (n = 70, p < 0.001). Dynamic impedance monitoring can be used as a macroscopic real-time prediction of the anastomosis effect.

Self-triggering topology for high-power nanosecond pulse generators based on avalanche transistors Marx bank circuits and linear transformer driver

In recent years, several novel avalanche transistor-based power synthesis topologies have been proposed to improve the output performance of pulse generators based on avalanche transistors. The most promising is the topology based on avalanche transistors Marx Bank Circuits (MBCs) and linear transformer driver (LTD). However, it suffers from the same problems as other semiconductor switch-based LTD generators. The greater the number of LTD modules, the higher the requirements for synchronization and drive capability of the trigger system. This paper proposes a new self-triggering topology for pulse generators based on avalanche transistors MBCs and LTD, which significantly simplifies the entire generator's requirement for trigger system synchronization and driving capability. First, the circuit topology and its operation principle are introduced. Then, three prototypes with one trigger LTD module and three self-triggering LTD modules are developed. The output characteristics are experimentally investigated. The results verify the feasibility of the proposed topology. Finally, the output amplitude and the rise time are 3.35 kV/3.7 ns, 4.12 kV/3.7 ns, and 4.88 kV/4.0 ns on a 25 Ω resistive load, respectively. All generators can operate at 1 kHz. The topology proposed in the article maximally simplifies the requirements for synchronization and drive capability of the trigger system for generators based on avalanche transistor MBCs and LTD.

New advances in solid-state pulse generator based on magnetic switches

Pulsed power technology is gradually forming a development trend of civil-military integration, which puts forward more requirements for pulsed power generators. This paper takes magnetic switches (MSs) as the starting point and reviews recent advancements in pulse generators based on MSs. First, the working mechanism of the MS "rapid inductance drop after magnetic core saturation" is analyzed. Second, the basic uses of MSs are introduced with specific examples, namely, magnetic compression unit, saturated pulse transformer, and magnetic delay switches. Then, the typical topologies of pulse generators based on MSs are discussed, including transmission line, Marx, Fitch, linear transformer driver, and semiconductor opening switch pumping circuits. These circuits' technical characteristics and parameter levels are highlighted. Finally, the existing problems and future development trends of MS-based solid-state pulse generators are discussed.

Modeling of a single bipolar electrode with tines for irreversible electroporation delivery

Irreversible electroporation (IRE) is a non-thermal tumor ablation technology employed to treat solid tumors not amenable to resection or thermal ablation. The IRE systems currently in clinical use deliver electrical pulses via multiple monopolar electrodes. This approach can present significant technical challenges due to the requirement for accurate placement of multiple electrodes and maintenance of parallel electrode alignment during pulse delivery. In this study, we sought to evaluate a novel IRE electrode configuration consisting of a single bipolar electrode with deployable tines. Using commercial finite element software predicted ablation outcomes, thermal damage, ablation sphericity, and energy delivery were calculated for existing monopolar and bipolar electrodes, and bipolar electrodes with either 4 or 8 deployable tines. The bipolar electrodes with tines generated larger predicted ablations compared to existing monopolar (>100%) and bipolar (>10%) arrangements, and the ablation shape using bipolar electrodes with tines were more spherical than those modeled for bipolar electrodes. Thermal damage modeled for bipolar electrodes and bipolar electrodes with tines was less than that of monopolar electrodes (using identical pulse parameters), and bipolar electrodes with tines delivered less energy than monopolar or bipolar electrodes. These studies using a single point of device insertion suggest the potential for developing alternative IRE delivery techniques, and may simplify clinical use and increase the predicted ablation shape/volume.

Dielectric Dispersion Modulated Sensing of Yeast Suspension Electroporation

A specific pulsed electric field protocol can be used to induce electroporation. This is used in the food industry for yeast pasteurization, in laboratories for generic transfer and the medical field for cancer treatment. The sensing of electroporation can be done with simple ‘instantaneous’ voltage-current analysis. However, there are some intrinsic low-frequency phenomena superposing the electroporation current, such as electrode polarization. The biological media are non-homogeneous, giving them specific characterization in the broad frequency spectrum. For example, the cell barrier, i.e., cell membrane, causes so called β-dispersion in the frequency range of tens to thousands of kHz. Electroporation is a dynamic phenomenon characterized by altering the cell membrane permeability. In this work, we show that the impedance measurement at certain frequencies could be used to detect the occurrence of electroporation, i.e., dielectric dispersion modulated sensing. This approach may be used for the design and implementation of electroporation systems. Yeast suspension electroporation is simulated to show changes in the frequency spectrum. Moreover, the alteration depends on characteristics of the system. Three types of external buffers and their characteristics are evaluated.

High Frequency Bipolar Electroporator with Double-Crowbar Circuit for Load-Independent Forming of Nanosecond Pulses

In this work, a novel electroporation system (electroporator) is presented, which is capable of forming high frequency pulses in a broad range of parameters (65 ns–100 µs). The electroporator supports voltages up to 3 kV and currents up to 40 A and is based on H-bridge circuit topology. A synchronized double crowbar driving sequence is introduced to generate short nanosecond range pulses independently of the electroporator load. The resultant circuit generates pulses with repetition frequencies up to 5 MHz and supports unipolar, bipolar, and asymmetrical pulse sequences with arbitrary waveforms. The shortest pulse duration step is hardware limited to 33 ns. The electroporator was experimentally tested on the H69AR human lung cancer cell line using 20 kV/cm bipolar and unipolar 100 ns–1 μs pulses. Based on a YO-PRO-1 permeabilization assay, it was determined that the electroporator is suitable for applied research on electroporation. The system offers high flexibility in experimental design to trigger various electroporation-based phenomena.

An Investigation for Large Volume, Focal Blood-Brain Barrier Disruption with High-Frequency Pulsed Electric Fields

The treatment of CNS disorders suffers from the inability to deliver large therapeutic agents to the brain parenchyma due to protection from the blood-brain barrier (BBB). Herein, we investigated high-frequency pulsed electric field (HF-PEF) therapy of various pulse widths and interphase delays for BBB disruption while selectively minimizing cell ablation. Eighteen male Fisher rats underwent craniectomy procedures and two blunt-tipped electrodes were advanced into the brain for pulsing. BBB disruption was verified with contrast T1W MRI and pathologically with Evans blue dye. High-frequency irreversible electroporation cell death of healthy rodent astrocytes was investigated in vitro using a collagen hydrogel tissue mimic. Numerical analysis was conducted to determine the electric fields in which BBB disruption and cell ablation occur. Differences between the BBB disruption and ablation thresholds for each waveform are as follows: 2-2-2 μs (1028 V/cm), 5-2-5 μs (721 V/cm), 10-1-10 μs (547 V/cm), 2-5-2 μs (1043 V/cm), and 5-5-5 μs (751 V/cm). These data suggest that HF-PEFs can be fine-tuned to modulate the extent of cell death while maximizing peri-ablative BBB disruption. Furthermore, numerical modeling elucidated the diffuse field gradients of a single-needle grounding pad configuration to favor large-volume BBB disruption, while the monopolar probe configuration is more amenable to ablation and reversible electroporation effects.

Characterization of dispersion and anisotropic-conductivity in tissue model during electroporation pulses

Electroporation occurs when biological cells are exposed to intensive, short-duration pulses, which can be used to ablate biological tumor tissues. Based on the traditional numerical models, the isotropic conductivity model with the non-dispersion effect (ICND), the anisotropic conductivity model with the dispersion effect (ACD) is developed in this study. The second-order Debye function is introduced to manifest the dielectric relaxation effect, and the two-dimensional Cartesian conductivity matrix is applied to describe the anisotropy of the tissue conductivity during the electroporation process. A monopolar pulse and a monopolar burst are applied to the breast tumor model through the two-needle electrodes configuration. The results show that taking the dispersion into account can increase the total electroporated area more than 2.31%. Considering the conductivity anisotropy, the total electroporated area increases, but the irreversible electroporation (IRE) area decreases by more than 3.99%. The ACD model can achieve a larger electroporated area but a relatively smaller IRE area than those of the ICND model, and comparably minor maximum thermal damage is evaluated in the ACD model. Our model analyzes the effects of the dielectric dispersion and anisotropic conductivity of tissue, which have strong guiding significance for making the treatment planning before clinical practice.

Effects of Time Delay Between Unipolar Pulses in High Frequency Nano-Electrochemotherapy

This work focuses on bleomycin electrochemotherapy using new modality of high repetition frequency unipolar nanosecond pulses. As a tumor model, Lewis lung carcinoma (LLC1) cell line in C57BL mice (n = 42) was used. Electrochemotherapy was performed with intertumoral injection of bleomycin (50 L of 1500 IU solution) followed by nanosecond and microsecond range electrical pulse delivery via parallel plate electrodes. The 3.5 kV/cm pulses of 200 and 700 ns were delivered in a burst of 200 at frequencies of 1 kHz and 1 MHz. For comparison of treatment efficiency, a standard 1.3 kV/cm x 100 s x 8 protocol was used. It was shown that it is possible to manipulate the efficacy of unipolar sub-microsecond electrochemotherapy solely by the time delay between the pulses. Also, the results suggest that the sub-microsecond range pulses can be as effective as the protocols in European Standard Operating Procedures on Electrochemotherapy (ESOPE) using 100 s pulses.

Evaluation of electroporated area using 2,3,5-triphenyltetrazolium chloride in a potato model

Irreversible electroporation (IRE) is a tissue ablation method, uses short high electric pulses and results in cell death in target tissue by irreversibly permeabilizing the cell membrane. Potato is commonly used as a tissue model for electroporation experiments. The blackened area that forms 12 h after electric pulsing is regarded as an IRE-ablated area caused by melanin accumulation. Here, the 2,3,5-triphenyltetrazolium chloride (TTC) was used as a dye to assess the IRE-ablated area 3 h after potato model ablation. Comparison between the blackened area and TTC-unstained white area in various voltage conditions showed that TTC staining well delineated the IRE-ablated area. Moreover, whether the ablated area was consistent over time and at different staining times was investigated. In addition, the presumed reversible electroporation (RE) area was formed surrounding the IRE-ablated area. Overall, TTC staining can provide a more rapid and accurate electroporated area evaluation.

A Theoretical Argument for Extended Interpulse Delays in Therapeutic High-Frequency Irreversible Electroporation Treatments

High-frequency irreversible electroporation (H-FIRE) is a tissue ablation modality employing bursts of electrical pulses in a positive phase-interphase delay (d1)-negative phase-interpulse delay (d2) pattern. Despite accumulating evidence suggesting the significance of these delays, their effects on therapeutic outcomes from clinically-relevant H-FIRE waveforms have not been studied extensively.

OBJECTIVE

We sought to determine whether modifications to the delays within H-FIRE bursts could yield a more desirable clinical outcome in terms of ablation volume versus extent of tissue excitation.

METHODS

We used a modified spatially extended nonlinear node (SENN) nerve fiber model to evaluate excitation thresholds for H-FIRE bursts with varying delays. We then calculated non-thermal tissue ablation, thermal damage, and excitation in a clinically relevant numerical model.

RESULTS

Excitation thresholds were maximized by shortening d1, and extension of d2 up to 1,000 μs increased excitation thresholds by at least 60% versus symmetric bursts. In the ablation model, long interpulse delays lowered the effective frequency of burst waveforms, modulating field redistribution and reducing heat production. Finally, we demonstrate mathematically that variable delays allow for increased voltages and larger ablations with similar extents of excitation as symmetric waveforms.

CONCLUSION

Interphase and interpulse delays play a significant role in outcomes resulting from H-FIRE treatment.

SIGNIFICANCE

Waveforms with short interphase delays (d1) and extended interpulse delays (d2) may improve therapeutic efficacy of H-FIRE as it emerges as a clinical tissue ablation modality.

High voltage nanosecond pulse generator based on diode opening switch and magnetic switch

Low-temperature plasma technology is widely used in various industrial fields, which require the plasma to be of large volume, diffuse, and stable. Furthermore, previous studies have shown that better plasma performance has been obtained by using generators with a high voltage, a high repetition rate, a fast rise time, and a short pulse duration. In this paper, a novel topology is proposed for such generators, which is based on magnetic switches and diode opening switches. A prototype is developed, and its output characteristics are investigated by varying essential parameters, such as the load resistance and the power supply voltage. The experimental results show that it can generate pulses with a voltage of 30.6 kV, a rise time of 7.1 ns, a pulse duration of 8.2 ns, and a maximum repetition rate of 12 kHz on a 300 Ω resistive load. The prototype has been successfully used to drive uniform plasma in ambient air. In the proposed topology, a diode is added to make the magnetic cores independent of each other, significantly simplifying the design calculation. It may help develop nanosecond solid-state generators.

Rapid Impedance Spectroscopy for Monitoring Tissue Impedance, Temperature, and Treatment Outcome During Electroporation-Based Therapies

OBJECTIVE

Electroporation-based therapies (EBTs) employ high voltage pulsed electric fields (PEFs) to permeabilize tumor tissue; this results in changes in electrical properties detectable using electrical impedance spectroscopy (EIS). Currently, commercial potentiostats for EIS are limited by impedance spectrum acquisition time (  ∼ 10 s); this timeframe is much larger than pulse periods used with EBTs (  ∼ 1 s). In this study, we utilize rapid EIS techniques to develop a methodology for characterizing electroporation (EP) and thermal effects associated with high-frequency irreversible EP (H-FIRE) in real-time by monitoring inter-burst impedance changes.

METHODS

A charge-balanced, bipolar rectangular chirp signal is proposed for rapid EIS. Validation of rapid EIS measurements against a commercial potentiostat was conducted in potato tissue using flat-plate electrodes and thereafter for the measurement of impedance changes throughout IRE treatment. Flat-plate electrodes were then utilized to uniformly heat potato tissue; throughout high-voltage H-FIRE treatment, low-voltage inter-burst impedance measurements were used to continually monitor impedance change and to identify a frequency at which thermal effects are delineated from EP effects.

RESULTS

Inter-burst impedance measurements (1.8 kHz - 4.93 MHz) were accomplished at 216 discrete frequencies. Impedance measurements at frequencies above  ∼ 1 MHz served to delineate thermal and EP effects in measured impedance.

CONCLUSION

We demonstrate rapid-capture ( 1 s) EIS which enables monitoring of inter-burst impedance in real-time. For the first time, we show impedance analysis at high frequencies can delineate thermal effects from EP effects in measured impedance.

SIGNIFICANCE

The proposed waveform demonstrates the potential to perform inter-burst EIS using PEFs compatible with existing pulse generator topologies.

Multi-Tissue Analysis on the Impact of Electroporation on Electrical and Thermal Properties

OBJECTIVE

Tissue electroporation is achieved by applying a series of electric pulses to destabilize cell membranes within the target tissue. The treatment volume is dictated by the electric field distribution, which depends on the pulse parameters and tissue type and can be readily predicted using numerical methods. These models require the relevant tissue properties to be known beforehand. This study aims to quantify electrical and thermal properties for three different tissue types relevant to current clinical electroporation.

METHODS

Pancreatic, brain, and liver tissue were harvested from pigs, then treated with IRE pulses in a parallel-plate configuration. Resulting current and temperature readings were used to calculate the conductivity and its temperature dependence for each tissue type. Finally, a computational model was constructed to examine the impact of differences between tissue types.

RESULTS

Baseline conductivity values (mean 0.11, 0.14, and 0.12 S/m) and temperature coefficients of conductivity (mean 2.0, 2.3, and 1.2 % per degree Celsius) were calculated for pancreas, brain, and liver, respectively. The accompanying computational models suggest field distribution and thermal damage volumes are dependent on tissue type.

CONCLUSION

The three tissue types show similar electrical and thermal responses to IRE, though brain tissue exhibits the greatest differences. The results also show that tissue type plays a role in the expected ablation and thermal damage volumes.

SIGNIFICANCE

The conductivity and its changes due to heating are expected to have a marked impact on the ablation volume. Incorporating these tissue properties aids in the prediction and optimization of electroporation-based therapies.

Electrochemotherapy Using Doxorubicin and Nanosecond Electric Field Pulses: A Pilot in Vivo Study

Pulsed electric field (PEF) is frequently used for intertumoral drug delivery resulting in a well-known anticancer treatment-electrochemotherapy. However, electrochemotherapy is associated with microsecond range of electrical pulses, while nanosecond range electrochemotherapy is almost non-existent. In this work, we analyzed the feasibility of nanosecond range pulse bursts for successful doxorubicin-based electrochemotherapy in vivo. The conventional microsecond (1.4 kV/cm × 100 µs × 8) procedure was compared to the nanosecond (3.5 kV/cm × 800 ns × 250) non-thermal PEF-based treatment. As a model, Sp2/0 tumors were developed. Additionally, basic current and voltage measurements were performed to detect the characteristic conductivity-dependent patterns and to serve as an indicator of successful tumor permeabilization both in the nano and microsecond pulse range. It was shown that nano-electrochemotherapy can be the logical evolution of the currently established European Standard Operating Procedures for Electrochemotherapy (ESOPE) protocols, offering better energy control and equivalent treatment efficacy.

A numerical study on the effect of conductivity change in cell kill distribution in irreversible electroporation

Introduction: irreversible electroporation (IRE) is a tissue ablation technique and physical process used to kill the undesirable cells. In the IRE process by mathematical modelling we can calculate the cell kill probability and distribution inside the tissue. The purpose of the study is to determine the influence of electric conductivity change in the IRE process into the cell kill probability and distribution.

Methods: cell death probability and electric conductivity were calculated with COMSOL Multiphysics software package. 8 pulses with a frequency of 1 Hz, pulse width of 100 µs and electric field intensity from 1000 to 3000 V/Cm with steps of 500 V/Cm used as electric pulses.

Results: significantly, the electrical conductivity of tissue will increase during the time of pulse delivery. According to our results, electrical conductivity increased with an electric field intensity of pulses. By considering the effect of conductivity change on cell kill probability, the cell kill probability and distribution will change.

Conclusion: we believe that considering the impact of electric conductivity change on the cell kill probability will improve the accuracy of treatment outcome in the clinic for treatment with IRE.

Real-Time Impedance Monitoring During Electroporation Processes in Vegetal Tissue Using a High-Performance Generator

Classical application of electroporation is carried out by using fixed protocols that do not clearly assure the complete ablation of the desired tissue. Nowadays, new methods that pursue the control of the treatment by studying the change in impedance during the applied pulses as a function of the electric field are being developed. These types of control seek to carry out the treatment in the fastest way, decreasing undesired effects and treatment time while ensuring the proper tumour ablation. The objective of this research is to determine the state of the treatment by continuously monitoring the impedance by using a novel versatile high-voltage generator and sensor system. To study the impedance dynamics in real time, the use of pulses of reduced voltage, below the threshold of reversible electroporation, is tested to characterise the state-of-the-treatment without interfering with it. With this purpose, a generator that provides both low voltage for sense tissue changes and high voltage for irreversible electroporation (IRE) was developed. In conclusion, the characterisation of the effects of electroporation in vegetal tissue, combined with the real-time monitoring of the state-of-the-treatment, will enable the provision of safer and more effective treatments.

Development of a Multi-Pulse Conductivity Model for Liver Tissue Treated With Pulsed Electric Fields

Pulsed electric field treatment modalities typically utilize multiple pulses to permeabilize biological tissue. This electroporation process induces conductivity changes in the tissue, which are indicative of the extent of electroporation. In this study, we characterized the electroporation-induced conductivity changes using all treatment pulses instead of solely the first pulse as in conventional conductivity models. Rabbit liver tissue was employed to study the tissue conductivity changes caused by multiple, 100 μs pulses delivered through flat plate electrodes. Voltage and current data were recorded during treatment and used to calculate the tissue conductivity during the entire pulsing process. Temperature data were also recorded to quantify the contribution of Joule heating to the conductivity according to the tissue temperature coefficient. By fitting all these data to a modified Heaviside function, where the two turning points (E₀, E₁) and the increase factor (A) are the main parameters, we calculated the conductivity as a function of the electric field (E), where the parameters of the Heaviside function (A and E₀) were functions of pulse number (N). With the resulting multi-factor conductivity model, a numerical electroporation simulation can predict the electrical current for multiple pulses more accurately than existing conductivity models. Moreover, the saturating behavior caused by electroporation can be explained by the saturation trends of the increase factor A in this model. The conductivity change induced by electroporation has a significant increase at about the first 30 pulses, then tends to saturate at 0.465 S/m. The proposed conductivity model can simulate the electroporation process more accurately than the conventional conductivity model. The electric field distribution computed using this model is essential for treatment planning in biomedical applications utilizing multiple pulsed electric fields, and the method proposed here, relating the pulse number to the conductivity through the variables in the Heaviside function, may be adapted to investigate the effect of other parameters, like pulse frequency and pulse width, on electroporation.

Application of bioimpedance spectroscopy to characterize chemoresistant tumor cell selectivity of nanosecond pulse stimulation

The discriminating effects of nanosecond pulsed electric fields (nsPEFs) between chemoresistant tumor cells (CRTCs) and their respective homologous chemosensitive tumor cells (CSTCs) were investigated based on bioimpedance spectroscopy (BIS). The electrical properties of individual untreated cells were determined by fitting the impedance spectra to an equivalent circuit model and then using aided simulations to calculate the nuclear envelope transmembrane potential (nTMP) and electroporation area on the nuclear envelope. Additionally, fluorescence staining assays of cell monolayers after nanopulse stimulation (80 pulses, 200 ns, 3 kV) were conducted to validate the simulation results. The staining results indicated that CRTCs showed a larger ablation area and lower lethal threshold compared to CSTCs after exposure to the same nsPEF energy, which was in accordance with the higher nTMP and larger electroporation area calculated for CRTCs. The increase in the lethal effects of nsPEFs on CRTCs compared to CSTCs mainly resulted from the superposition of the changes in the electrical properties and nuclear size. The work shows that BIS can distinguish CRTCs and CSTCs and the corresponding nsPEF effects, suggesting potential applications for the optimization of novel anti-chemoresistance methods, including nsPEF-treatments.

Understanding the role of calcium-mediated cell death in high-frequency irreversible electroporation

High-frequency irreversible electroporation (H-FIRE) is an emerging electroporation-based therapy used to ablate cancerous tissue. Treatment consists of delivering short, bipolar pulses (1-10μs) in a series of 80-100 bursts (1 burst/s, 100μs on-time). Reducing pulse duration leads to reduced treatment volumes compared to traditional IRE, therefore larger voltages must be applied to generate ablations comparable in size. We show that adjuvant calcium enhances ablation area in vitro for H-FIRE treatments of several pulse durations (1, 2, 5, 10μs). Furthermore, H-FIRE treatment using 10μs pulses delivered with 1mM CaCl₂ results in cell death thresholds (771±129V/cm) comparable to IRE thresholds without calcium (698±103V/cm). Quantifying the reversible electroporation threshold revealed that CaCl₂ enhances the permeabilization of cells compared to a NaCl control. Gene expression analysis determined that CaCl₂ upregulates expression of eIFB5 and 60S ribosomal subunit genes while downregulating NOX1/4, leading to increased signaling in pathways that may cause necroptosis. The opposite was found for control treatment without CaCl₂ suggesting cells experience an increase in pro survival signaling. Our study is the first to identify key genes and signaling pathways responsible for differences in cell response to H-FIRE treatment with and without calcium.

Experimental High-Frequency Irreversible Electroporation Using a Single-Needle Delivery Approach for Nonthermal Pancreatic Ablation In Vivo

PURPOSE

To investigate the feasibility of single-needle high-frequency irreversible electroporation (SN-HFIRE) to create reproducible tissue ablations in an in vivo pancreatic swine model.

MATERIALS AND METHODS

SN-HFIRE was performed in swine pancreas in vivo in the absence of intraoperative paralytics or cardiac synchronization using 3 different voltage waveforms (1-5-1, 2-5-2, and 5-5-5 [on-off-on times (μs)], n = 6/setting) with a total energized time of 100 μs per burst. At necropsy, ablation size/shape was determined. Immunohistochemistry was performed to quantify apoptosis using an anticleaved caspase-3 antibody. A numerical model was developed to determine lethal thresholds for each waveform in pancreas.

RESULTS

Mean tissue ablation time was 5.0 ± 0.2 minutes, and no cardiac abnormalities or muscle twitch was detected. Mean ablation area significantly increased with increasing pulse width (41.0 ± 5.1 mm² [range 32-66 mm²] vs 44 ± 2.1 mm² [range 38-56 mm²] vs 85.0 ± 7.0 mm² [range 63-155 mm²]; 1-5-1, 2-5-2, 5-5-5, respectively; p < 0.0002 5-5-5 vs 1-5-1 and 2-5-2). The majority of the ablation zone did not stain positive for cleaved caspase-3 (6.1 ± 2.8% [range 1.8-9.1%], 8.8 ± 1.3% [range 5.5-14.0%], and 11.0 ± 1.4% [range 7.1-14.2%] cleaved caspase-3 positive 1-5-1, 2-5-2, 5-5-5, respectively), with significantly more positive staining at the 5-5-5 pulse setting compared with 1-5-1 (p < 0.03). Numerical modeling determined a lethal threshold of 1114 ± 123 V/cm (1-5-1 waveform), 1039 ± 103 V/cm (2-5-2 waveform), and 693 ± 81 V/cm (5-5-5 waveform).

CONCLUSIONS

SN-HFIRE induces rapid, predictable ablations in pancreatic tissue in vivo without the need for intraoperative paralytics or cardiac synchronization.

Cancellation effect is present in high-frequency reversible and irreversible electroporation

It was recently suggested that applying high-frequency short biphasic pulses (HF-IRE) reduces pain and muscle contractions in electrochemotherapy and irreversible ablation treatments; however, higher amplitudes with HF-IRE pulses are required to achieve a similar effect as with monophasic pulses. HF-IRE pulses are in the range of a microseconds, thus, the so-called cancellation effect could be responsible for the need to apply pulses of higher amplitudes. In cancellation effect, the effect of first pulse is reduced by the second pulse of opposite polarity. We evaluated cancellation effect with high-frequency biphasic pulses on CHO-K1 in different electroporation buffers. We applied eight bursts of 1-10 µs long pulses with inter-phase delays of 0.5 µs - 10 ms and evaluated membrane permeability and cell survival. In permeability experiments, cancellation effect was not observed in low-conductivity buffer. Cancellation effect was, however, observed in treatments with high-frequency biphasic pulses looking at survival in all of the tested electroporation buffers. In general, cancellation effect depended on inter-phase delay as well as on pulse duration, i.e. longer pulses and longer interphase delay cause less pronounced cancellation effect. Cancellation effect could be partially explained by the assisted discharge and not by the hyperpolarization by the chloride channels.

Conductivity change with needle electrode during high frequency irreversible electroporation: a finite element study

Irreversible electroporation (IRE) is a process in which the cell membrane is damaged and leads to cell death. IRE has been used as a minimally invasive ablation tool. This process is affected by some factors. The most important factor is the electric field distribution inside the tissue. The electric field distribution depends on the electric pulse parameters and tissue properties, such as the electrical conductivity of tissue. The present study focuses on evaluating the tissue conductivity change due to high-frequency and low-voltage (HFLV) as well as low-frequency and high-voltage (LFHV) pulses during irreversible electroporation. We were used finite element analysis software, COMSOL Multiphysics 5.0, to calculate the conductivity change of the liver tissue. The HFLV pulses in this study involved 4000 bipolar and monopolar pulses with a frequency of 5 kHz, pulse width of 100 µs, and electric field intensity from 100 to 300 V/cm. On the other hand, the LFHV pulses, which we were used, included 8 bipolar and monopolar pulses with a frequency of 1 Hz, the pulse width of 2 ms and electric field intensity of 2500 V/cm. The results demonstrate that the conductivity change for LFHV pulses due to the greater electric field intensity was higher than for HFLV pulses. The most significant conclusion is the HFLV pulses can change tissue conductivity only in the vicinity of the tip of electrodes. While LFHV pulses change the electrical conductivity significantly in the tissue of between electrodes.

Temporal Characterization of Blood-Brain Barrier Disruption with High-Frequency Electroporation

Treatment of intracranial disorders suffers from the inability to accumulate therapeutic drug concentrations due to protection from the blood–brain barrier (BBB). Electroporation-based therapies have demonstrated the capability of permeating the BBB, but knowledge of the longevity of BBB disruption (BBBD) is limited. In this study, we quantify the temporal, high-frequency electroporation (HFE)-mediated BBBD in an in vivo healthy rat brain model. 40 male Fisher rats underwent HFE treatment; two blunt tipped monopolar electrodes were advanced into the brain and 200 bursts of HFE were delivered at a voltage-to-distance ratio of 600 V/cm. BBBD was verified with contrast enhanced T1W MRI (gadopentetate dimeglumine) and pathologically (Evans blue dye) at time points of 1, 24, 48, 72, and 96 h after HFE. Contrast enhanced T1W scans demonstrated BBBD for 1 to 72 h after HFE but intact BBB at 96 h. Histologically, tissue damage was restricted to electrode insertion tracks. BBBD was induced with minimal muscle contractions and minimal cell death attributed to HFE. Numerical modeling indicated that brief BBBD was induced with low magnitude electric fields, and BBBD duration increased with field strength. These data suggest the spatiotemporal characteristics of HFE-mediated BBBD may be modulated with the locally applied electric field.

Successful Tumor Electrochemotherapy Using Sine Waves

OBJECTIVE

The purpose of this work is to assess the ability of sine waves to perform electrochemotherapy (ECT) and to study the dependence of the frequency of the applied sine wave on the treatment efficacy.

METHODS

A subcutaneous tumor model in mice was used, and the electric field was delivered in combination with bleomycin. Sinusoidal electric fields of different frequencies, amplitudes, and durations were compared to square waves. Computer simulations were additionally performed.

RESULTS

The results confirmed the ability of a sinusoidal electric field to obtain successful ECT responses. A strong dependence on frequency was obtained. The efficacy of the treatment decreased when the frequency of the sine waves was increased. At low sinusoidal frequency, the efficacy of the treatment is very similar to that obtained with a square wave. The collateral effects such as skin burns and muscle contractions decreased for the highest frequency assayed.

CONCLUSION

The use of sine wave burst represents a feasible option for the treatment of cancer by ECT.

SIGNIFICANCE

These results could have important implications for the treatment of cancer in the clinical world where ECT is performed with dc square pulses.

The use of high-frequency short bipolar pulses in cisplatin electrochemotherapy in vitro

Background

In electrochemotherapy (ECT), chemotherapeutics are first administered, followed by short 100 μs monopolar pulses. However, these pulses cause pain and muscle contractions. It is thus necessary to administer muscle relaxants, general anesthesia and synchronize pulses with the heart rhythm of the patient, which makes the treatment more complex. It was suggested in ablation with irreversible electroporation, that bursts of short high-frequency bipolar pulses could alleviate these problems. Therefore, we designed our study to verify if it is possible to use high-frequency bipolar pulses (HF-EP pulses) in electrochemotherapy.

Materials and methods

We performed in vitro experiments on mouse skin melanoma (B16-F1) cells by adding 1–330 μM cisplatin and delivering either (a) eight 100 μs long monopolar pulses, 0.4–1.2 kV/cm, 1 Hz (ECT pulses) or (b) eight bursts at 1 Hz, consisting of 50 bipolar pulses. One bipolar pulse consisted of a series of 1 μs long positive and 1 μs long negative pulse (0.5–5 kV/cm) with a 1 μs delay in-between.

Results

With both types of pulses, the combination of electric pulses and cisplatin was more efficient in killing cells than cisplatin or electric pulses only. However, we needed to apply a higher electric field in HF-EP (3 kV/cm) than in ECT (1.2 kV/cm) to obtain comparable cytotoxicity.

Conclusions

It is possible to use HF-EP in electrochemotherapy; however, at the expense of applying higher electric fields than in classical ECT. The results obtained, nevertheless, offer an evidence that HF-EP could be used in electrochemotherapy with potentially alleviated muscle contractions and pain.