A Bayesian Approach for Coincidence Resolution in Microfluidic Impedance Cytometry

On the compatibility of single-cell microcarriers (nanovials) with microfluidic impedance cytometry

We investigate for the first time the compatibility of nanovials with microfluidic impedance cytometry (MIC). Nanovials are suspendable crescent-shaped single-cell microcarriers that enable specific cell adhesion, the creation of compartments for undisturbed cell growth and secretion, as well as protection against wall shear stress. MIC is a label-free single-cell technique that characterizes flowing cells based on their electrical fingerprints and it is especially targeted to cells that are naturally in suspension. Combining nanovial technology with MIC is intriguing as it would represent a robust framework for the electrical analysis of single adherent cells at high throughput. Here, as a proof-of-concept, we report the MIC analysis of mesenchymal stromal cells loaded in nanovials. The electrical analysis is supported by numerical simulations and validated by means of optical analysis. We demonstrate that the electrical diameter can discriminate among free cells, empty nanovials, cell-loaded nanovials, and clusters, thus grounding the foundation for the use of nanovials in MIC. Furthermore, we investigate the potentiality of MIC to assess the electrical phenotype of cells loaded in nanovials and we draw directions for future studies.

Investigation of geometry-dependent sensing characteristics of microfluidic for single-cell 3D localization

Flow cytometry-based measurement techniques have been widely used for single-cell characterizations, such as impedance, size, and dielectric properties. However, in the measurement process, the reliability of the output measurement signal directly affects the ability of the microsystem to judge the characteristics of single cells. Here, we designed a multiple nonparallel electrode structure for single-cell 3D localization. The performance of the structures was studied by analyzing the changes in electric field strength and the output differential current. The effects of microchannel height, sensing electrode distance, electrode inclination angle, and electrode width on output signals are investigated by analyzing the current change and electric field strength of single cells passing from the center of the microchannel. The numerical simulation results indicate that, when the microchannel height is 20 µm, the distance of the sensing electrodes is 100 µm, the inclination angle is 30°, the electrode width is 20 µm, and the optimal signal quality can be obtained. Reducing the height of the flow channel and shortening the sensing electrode spacing can significantly improve the signal amplitude. When the channel height is 20 µm, the signal intensity increases by 80% than that of 30 µm. The signal intensity of induced current with the sensing electrode spacing of 100 µm is 42% higher than that with the spacing of 120 µm. We analyzed the presence of multiple independent cells and adherent cells in the detection area and demonstrated through simulation that the signal changes caused by multi-cells can be superimposed by multiple single-cell signals. The induced current signal intensity of the same volume of cells with an ellipticity of 1 is 49% lower than that of cells with an ellipticity of 4. Based on the numerical investigation, we expect that the optimal geometry structure design will aid in the development of better performance signal cell impedance cytometry microsystems.

Electrical micro flow cytometry with LSTM and its application in leukocyte differential

This paper developed an electrical micro flow cytometry to realize leukocyte differentials leveraging a constrictional microchannel and a deep neural network. Firstly, purified granulocytes, lymphocytes or monocytes traveled through the constrictional microchannel with a cross-sectional area marginally larger than individual cells and produced large impedance variations by blocking focused electric field lines. By optimizing key elements (e.g., normalization, learning rate, batch size and neuron number) of the recurrent neural network (RNN), electrical results of purified leukocytes were analyzed to establish a leukocyte differential system with a classification accuracy of 95.2%. Then the leukocyte mixtures were forced to travel through the same constrictional microchannel, producing mixed impedance profiles which were classified into granulocytes, lymphocytes and monocytes based on the aforementioned differential system. As to the classification results, two leukocyte mixtures from the same donor were processed, producing comparable classification results, which were 57% versus 59% of granulocytes, 37% versus 34% of lymphocytes and 6% versus 7% of monocytes. These results validated the established classification system based on the constrictional microchannel and the recurrent neural network, providing a new perspective of differentiating white blood cells by electrical flow cytometry.

Reproducibility in cytometry: Signals analysis and its connection to uncertainty quantification

Signals analysis for cytometry remains a challenging task that has a significant impact on uncertainty. Conventional cytometers assume that individual measurements are well characterized by simple properties such as the signal area, width, and height. However, these approaches have difficulty distinguishing inherent biological variability from instrument artifacts and operating conditions. As a result, it is challenging to quantify uncertainty in the properties of individual cells and perform tasks such as doublet deconvolution. We address these problems via signals analysis techniques that use scale transformations to: (I) separate variation in biomarker expression from effects due to flow conditions and particle size; (II) quantify reproducibility associated with a given laser interrogation region; (III) estimate uncertainty in measurement values on a per-event basis; and (IV) extract the singlets that make up a multiplet. The key idea behind this approach is to model how variable operating conditions deform the signal shape and then use constrained optimization to "undo" these deformations for measured signals; residuals to this process characterize reproducibility. Using a recently developed microfluidic cytometer, we demonstrate that these techniques can account for instrument and measurand induced variability with a residual uncertainty of less than 2.5% in the signal shape and less than 1% in integrated area.

Rapid Assessment of Susceptibility of Bacteria and Erythrocytes to Antimicrobial Peptides by Single-Cell Impedance Cytometry

Antimicrobial peptides (AMPs) represent a promising class of compounds to fight antibiotic-resistant infections. In most cases, they kill bacteria by making their membrane permeable and therefore exhibit low propensity to induce bacterial resistance. In addition, they are often selective, killing bacteria at concentrations lower than those at which they are toxic to the host. However, clinical applications of AMPs are hindered by a limited understanding of their interactions with bacteria and human cells. Standard susceptibility testing methods are based on the analysis of the growth of a bacterial population and therefore require several hours. Moreover, different assays are required to assess the toxicity to host cells. In this work, we propose the use of microfluidic impedance cytometry to explore the action of AMPs on both bacteria and host cells in a rapid manner and with single-cell resolution. Impedance measurements are particularly well-suited to detect the effects of AMPs on bacteria, due to the fact that the mechanism of action involves perturbation of the permeability of cell membranes. We show that the electrical signatures of Bacillus megaterium cells and human red blood cells (RBCs) reflect the action of a representative antimicrobial peptide, DNS-PMAP23. In particular, the impedance phase at high frequency (e.g., 11 or 20 MHz) is a reliable label-free metric for monitoring DNS-PMAP23 bactericidal activity and toxicity to RBCs. The impedance-based characterization is validated by comparison with standard antibacterial activity assays and absorbance-based hemolytic activity assays. Furthermore, we demonstrate the applicability of the technique to a mixed sample of B. megaterium cells and RBCs, which paves the way to study AMP selectivity for bacterial versus eukaryotic cells in the presence of both cell types.

A low-cost, label-free microfluidic scanning flow cytometer for high-accuracy quantification of size and refractive index of particles

Flow cytometers and fluorescence activated cells sorters (FCM/FACS) represent the gold standard for high-throughput single-cell analysis, but their usefulness for label-free applications is limited by the unreliability of forward and side scatter measurements. Scanning flow cytometers represent an appealing alternative, as they exploit measurements of the angle-resolved scattered light to provide accurate and quantitative estimates of cellular properties, but the requirements of current setups are unsuitable for integration with other lab-on-chip technologies or for point-of-care applications. Here we present the first microfluidic scanning flow cytometer (μSFC), able to achieve accurate angle-resolved scattering measurements within a standard polydimethylsiloxane microfluidic chip. The system exploits a low cost linearly variable optical density (OD) filter to reduce the dynamic range of the signal and to increase its signal-to-noise ratio. We present a performance comparison between the μSFC and commercial machines for the label free characterization of polymeric beads with different diameters and refractive indices. In contrast to FCM and FACS, the μSFC yields size estimates linearly correlated with nominal particle sizes (R² = 0.99) and quantitative estimates of particle refractive indices. The feasibility of using the μSFC for the characterization of biological samples is demonstrated by analyzing a population of monocytes identified based on the morphology of a peripheral blood mononuclear cells sample, which yields values in agreement with the literature. The proposed μSFC combines low setup requirements with high performance, and has great potential for integration within other lab-on-chip systems for multi-parametric cell analysis and for next-generation point-of-care diagnostic applications.

Floating-Electrode-Enabled Impedance Cytometry for Single-Cell 3D Localization

As a label-free, low-cost, and noninvasive tool, impedance measurement has been widely used in single-cell characterization analysis. However, due to the tiny volume of cells, the uncertainty of the spatial position in the microchannel will bring measurement errors in single-cell electrical parameters. To overcome the issue, we designed a novel microdevice configured with a coplanar differential electrode structure to accurately resolve the spatial position of single cells without constraining techniques such as additional sheath fluids or narrow microchannels. The device precisely localizes single cells by measuring the induced current generated by the combined action of the floating electrode and the differential electrodes when single cells flow through the electrode-sensing area. The device was experimentally validated by measuring 6 μm yeast cells and 10 μm particles, achieving spatial localization with a resolution down to 2.1 μm (about 5.3% of the channel width) in lateral direction and 1.2 μm (about 5.9% of the channel height) in the vertical direction at a flow rate of 1.2 μL/min. In addition, by comparing measurement of yeast cells and particles, it was demonstrated that the device not only localizes the single cells or particles but also simultaneously characterizes their status properties such as velocity and size. The device offers a competitive electrode configuration in impedance cytometry with the advantages of simple structure, low cost, and high throughput, promising cell localization and thus electrical characterization.

Cell density detection based on a microfluidic chip with two electrode pairs

Cell density detection is usually the counting of cells in certain volume of liquid, which is an important process in biological and medical fields. The Coulter counting method is an important method for biological cell detection and counting. In this paper, a microfluidic chip based on two electrode pairs is designed, which uses the Coulter principle to detect the flow rate of liquid and count the cells, and then calculate the cell density. When the cell passes through the sensor channel formed by the electrode pair on the chip, the impedance will change between the electrodes. This phenomenon has been proved by experiments. The designed chip has the advantages of simple structure, small size and low manufacturing cost. The cell density detection method proposed in this article is of great significance to the research in the field of biological cell detection and development of related medical devices.

A 10 M Ω, 50 kHz-40 MHz Impedance Measurement Architecture for Source-Differential Flow Cytometry

A low-power, impedance-based integrated circuit (IC) readout architecture is presented for cell analysis and cytometry applications. A three-electrode layout and source-differential excitation cancels baseline current prior to the sensor front-end, which enables the use of a high-gain readout circuit for the difference current. A lock-in architecture is employed with down-conversion and up-conversion in the feedback loop, enabling high closed-loop gain (up to 10 M Ω) and high bandwidth (up to 40 MHz). A hybrid-RC feedback network mitigates the SNR degradation seen over a wide operating frequency range when using purely capacitive feedback. The effect of phase shift on the closed-loop system gain and noise performance are analyzed in detail, along with optimization strategies, and the design includes fine-grained phase adjustment to minimize phase error. The impedance sensor was fabricated in a 0.18 μ m CMOS process and consumes 9.7 mW with an operating frequency from 50 kHz to 40 MHz and provides adjustable bandwidth. Measurements demonstrate that the impedance sensor achieves 6 pA [Formula: see text] input-referred noise over 200 Hz bandwidth at 0.5 MHz modulation frequency. Combined with a microfluidic flow cell, measured results using this source-differential measurement approach are presented using both monodisperse and polydisperse sample solutions and demonstrate single-cell resolution, detecting 3 μ m diameter particles in solution with 22 dB SNR.

Deciphering impedance cytometry signals with neural networks

Microfluidic impedance cytometry is a label-free technique for high-throughput single-cell analysis. Multi-frequency impedance measurements provide data that allows full characterisation of cells, linking electrical phenotype to individual biophysical properties. To efficiently extract the information embedded in the electrical signals, potentially in real-time, tailored signal processing is needed. Artificial intelligence approaches provide a promising new direction. Here we demonstrate the ability of neural networks to decipher impedance cytometry signals in two challenging scenarios: (i) to determine the intrinsic dielectric properties of single cells directly from raw impedance data streams, (ii) to capture single-cell signals that are hidden in the measured signals of coincident cells. The accuracy of the results and the high processing speed (fractions of ms per cell) demonstrate that neural networks can have an important role in impedance-based single-cell analysis.

A computer-aid multi-task light-weight network for macroscopic feces diagnosis

The abnormal traits and colors of feces typically indicate that the patients are probably suffering from tumor or digestive-system diseases. Thus a fast, accurate and automatic health diagnosis system based on feces is urgently necessary for improving the examination speed and reducing the infection risk. The rarity of the pathological images would deteriorate the accuracy performance of the trained models. In order to alleviate this problem, we employ augmentation and over-sampling to expand the samples of the classes that have few samples in the training batch. In order to achieve an impressive recognition performance and leverage the latent correlation between the traits and colors of feces pathological samples, a multi-task network is developed to recognize colors and traits of the macroscopic feces images. The parameter number of a single multi-task network is generally much smaller than the total parameter number of multiple single-task networks, so the storage cost is reduced. The loss function of the multi-task network is the weighted sum of the losses of the two tasks. In this paper, the weights of the tasks are determined according to their difficulty levels that are measured by the fitted linear functions. The sufficient experiments confirm that the proposed method can yield higher accuracies, and the efficiency is also improved.

Joint Particle Detection and Analysis by a CNN and Adaptive Norm Minimization Approach

Optical flow cytometry is used as the gold standard in single cell function diagnostics with the drawback of involving high complexity and operator costs. Magnetic flow cytometers try to overcome this problem by replacing optical labeling with magnetic nanoparticles to assign each cell a magnetic fingerprint. This allows operators to obtain rich cell information from a biological sample with minimal sample preparation at near in-vivo conditions in a decentralized environment. A central task in flow cytometry is the determination of cell concentrations and cell parameters, e.g. hydrodynamic diameter. For the acquisition of this information, signal processing is an essential component. Previous approaches mainly focus on the processing of one-cell signals, leaving out superimposed signals originating from cells passing the magnetic sensors in close proximity. In this work, we present a framework for joint cell/particle detection and analysis, which is capable of processing one-cell as well as multi-cell signals. We employ deep learning and compressive sensing in this approach, which involves the minimization of an adaptive norm. We evaluate our method on simulated and experimental signals, the latter being obtained with polymer microparticles. Our results show that the framework is capable of counting cells with a relative error smaller than 2 %. Inference of cell parameters works reliably at both low and high noise levels.

Time-domain signal averaging to improve microparticles detection and enumeration accuracy in a microfluidic impedance cytometer

Microfluidic impedance cytometry is a powerful system to measure micro and nano-sized particles and is routinely used in point-of-care disease diagnostics and other biomedical applications. However, small objects near a sensor's detection limit are plagued with relatively significant background noise and are difficult to identify for every case. While many data processing techniques can be utilized to reduce noise and improve signal quality, frequently they are still inadequate to push sensor detection limits. Here, we report the first demonstration of a novel signal averaging algorithm effective in noise reduction of microfluidic impedance cytometry data, improving enumeration accuracy, and reducing detection limits. Our device uses a 22 µm tall × 100 µm wide (with 30 µm wide focused aperture) microchannel and gold coplanar microelectrodes that generate an electric field, recording bipolar pulses from polystyrene microparticles flowing through the channel. In addition to outlining a modified moving signal averaging technique theoretically and with a model data set, we also performed a compendium of characterization experiments including variations in flow rate, input voltage, and particle size. Multivariate metrics from each experiment are compared including signal amplitude, pulse width, background noise, and signal-to-noise ratio (SNR). Incorporating our technique resulted in improved SNR and counting accuracy across all experiments conducted, and the limit of detection improved from 5 to 1 µm particles without modifying microchannel dimensions. Succeeding this, we envision implementing our modified moving average technique to develop next-generation microfluidic impedance cytometry devices with an expanded dynamic range and improved enumeration accuracy. This can be exceedingly useful for many biomedical applications, such as infectious disease diagnostics where devices may enumerate larger-scale immune cells alongside sub-micron bacterium in the same sample.

Electro-optical classification of pollen grains via microfluidics and machine learning

In aerobiological monitoring and agriculture there is a pressing need for accurate, label-free and automated analysis of pollen grains, in order to reduce the cost, workload and possible errors associated to traditional approaches. Methods: We propose a new multimodal approach that combines electrical sensing and optical imaging to classify pollen grains flowing in a microfluidic chip at a throughput of 150 grains per second. Electrical signals and synchronized optical images are processed by two independent machine learning-based classifiers, whose predictions are then combined to provide the final classification outcome. Results: The applicability of the method is demonstrated in a proof-of-concept classification experiment involving eight pollen classes from different taxa. The average balanced accuracy is 78.7 % for the electrical classifier, 76.7 % for the optical classifier and 84.2 % for the multimodal classifier. The accuracy is 82.8 % for the electrical classifier, 84.1 % for the optical classifier and 88.3 % for the multimodal classifier. Conclusion: The multimodal approach provides better classification results with respect to the analysis based on electrical or optical features alone. Significance: The proposed methodology paves the way for automated multimodal palynology. Moreover, it can be extended to other fields, such as diagnostics and cell therapy, where it could be used for label-free identification of cell populations in heterogeneous samples.

Microfluidic impedance cytometry for single-cell sensing: Review on electrode configurations

Single-cell analysis has gained considerable attention for disease diagnosis, drug screening, and differentiation monitoring. Compared to the well-established flow cytometry, which uses fluorescent-labeled antibodies, microfluidic impedance cytometry (MIC) offers a simple, label-free, and noninvasive method for counting, classifying, and monitoring cells. Superior features including a small footprint, low reagent consumption, and ease of use have also been reported. The MIC device detects changes in the impedance signal caused by cells passing through the sensing/electric field zone, which can extract information regarding the size, shape, and dielectric properties of these cells. According to recent studies, electrode configuration has a remarkable effect on detection accuracy, sensitivity, and throughput. With the improvement in microfabrication technology, various electrode configurations have been reported for improving detection accuracy and throughput. However, the various electrode configurations of MIC devices have not been reviewed. In this review, the theoretical background of the impedance technique for single-cell analysis is introduced. Then, two-dimensional, three-dimensional, and liquid electrode configurations are discussed separately; their sensing mechanisms, fabrication processes, advantages, disadvantages, and applications are also described in detail. Finally, the current limitations and future perspectives of these electrode configurations are summarized. The main aim of this review is to offer a guide for researchers on the ongoing advancement in electrode configuration designs.

Single-cell microfluidic impedance cytometry: from raw signals to cell phenotypes using data analytics

The biophysical analysis of single-cells by microfluidic impedance cytometry is emerging as a label-free and high-throughput means to stratify the heterogeneity of cellular systems based on their electrophysiology. Emerging applications range from fundamental life-science and drug assessment research to point-of-care diagnostics and precision medicine. Recently, novel chip designs and data analytic strategies are laying the foundation for multiparametric cell characterization and subpopulation distinction, which are essential to understand biological function, follow disease progression and monitor cell behaviour in microsystems. In this tutorial review, we present a comparative survey of the approaches to elucidate cellular and subcellular features from impedance cytometry data, covering the related subjects of device design, data analytics (i.e., signal processing, dielectric modelling, population clustering), and phenotyping applications. We give special emphasis to the exciting recent developments of the technique (timeframe 2017-2020) and provide our perspective on future challenges and directions. Its synergistic application with microfluidic separation, sensor science and machine learning can form an essential toolkit for label-free quantification and isolation of subpopulations to stratify heterogeneous biosystems.

Positional dependence of particles and cells in microfluidic electrical impedance flow cytometry: origin, challenges and opportunities

Microfluidic electrical impedance flow cytometry is now a well-known and established method for single-cell analysis. Given the richness of the information provided by impedance measurements, this non-invasive and label-free approach can be used in a wide field of applications ranging from simple cell counting to disease diagnostics. One of its major limitations is the variation of the impedance signal with the position of the cell in the sensing area. Indeed, identical particles traveling along different trajectories do not result in the same data. The positional dependence can be considered as a challenge for the accuracy of microfluidic impedance cytometers. On the other hand, it has recently been regarded by several groups as an opportunity to estimate the position of particles in the microchannel and thus take a further step in the logic of integrating sensors in so-called "Lab-on-a-chip" devices. This review provides a comprehensive overview of the physical grounds of the positional dependence of impedance measurements. Then, both the developed strategies to reduce position influence in impedance-based assays and the recent reported technologies exploiting that dependence for the integration of position detection in microfluidic devices are reviewed.