The Influence of Posture, Applied Force and Perturbation Direction on Hip Joint Viscoelasticity

Identification of Hip and Knee Joint Impedance During the Swing Phase of Walking

Knowledge on joint impedance during walking in various conditions is relevant for clinical decision-making and the development of robotic gait trainers, leg prostheses, leg orthotics and wearable exoskeletons. Whereas ankle impedance during walking has been experimentally assessed, knee and hip joint impedance during walking have not been identified yet. Here we developed and evaluated a lower limb perturbator to identify hip, knee and ankle joint impedance during treadmill walking. The lower limb perturbator (LOPER) consists of an actuator connected to the thigh via rods. The LOPER allows to apply force perturbations to a free-hanging leg, while standing on the contralateral leg, with a bandwidth of up to 39 Hz. While walking in minimal impedance mode, the interaction forces between LOPER and the thigh were low (<5 N) and the effect on the walking pattern was smaller than the within-subject variability during normal walking. Using a non-linear multibody dynamical model of swing leg dynamics, the hip, knee and ankle joint impedance were estimated at three time points during the swing phase for nine subjects walking at a speed of 0.5 m/s. The identified model was well able to predict the experimental responses for the hip and knee, since the mean variance accounted (VAF) for was 99% and 96%, respectively. The ankle lacked a consistent response and the mean VAF of the model fit was only 77%, and therefore the estimated ankle impedance was not reliable. The averaged across-subjects stiffness varied between the three time points within 34-66 and 0-3.5 Nm/rad Nm/rad for the hip and knee joint respectively. The damping varied between 1.9-4.6 and 0.02-0.14 Nms/rad Nms/rad for hip and knee respectively. The developed LOPER has a negligible effect on the unperturbed walking pattern and allows to identify hip and knee impedance during the swing phase.

Balance strategy in hoverboard control

This study examines how people learn to perform lower limb control in a novel task with a hoverboard requiring to maintain dynamic balance. We designed an experiment to investigate the learning of hoverboard balance and two control strategies: A hip strategy, which mainly uses hip movements to change the angle of the foot, and an ankle strategy relying more on ankle motion to control the orientation of hoverboard plates controlling the motion. Motor learning was indicated by a significant \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$10\pm 4$$\end{document}10±4% decrease in the trial completion time (p < 0.001) and a significant 24 ± 11% decrease in total muscle activation (p < 0.001). Furthermore, the participants, who had no prior experience riding a hoverboard, learned an ankle strategy to maintain their balance and control the hoverboard. This is supported by significantly stronger cross-correlation, phase synchrony, lower dynamic time warping distance between the hoverboard plate orientation controlling hoverboard motion, and the ankle angle when compared to the hip angle. The adopted ankle strategy was found to be robust to the foot orientation despite salient changes in muscle group activation patterns. Comparison with results of an experienced hoverboard rider confirmed that the first-time riders adopted an ankle strategy.

An Adaptive Assistance Controller to Optimize the Exoskeleton Contribution in Rehabilitation

In this paper, we present a novel adaptation rule to optimize the exoskeleton assistance in rehabilitation tasks. The proposed method adapts the exoskeleton contribution to user impairment severity without any prior knowledge about the user motor capacity. The proposed controller is a combination of an adaptive feedforward controller and a low gain adaptive PD controller. The PD controller guarantees the stability of the human-exoskeleton system during feedforward torque adaptation by utilizing only the human-exoskeleton joint positions as the sensory feedback for assistive torque optimization. In addition to providing a convergence proof, in order to study the performance of our method we applied it to a simplified 2-DOF model of human-arm and a generic 9-DOF model of lower limb to perform walking. In each simulated task, we implemented the impaired human torque to be insufficient for the task completion. Moreover, the scenarios that violate our convergence proof assumptions are considered. The simulation results show a converging behavior for the proposed controller; the maximum convergence time of 20 s is observed. In addition, a stable control performance that optimally supplements the remaining user motor contribution is observed; the joint angle tracking error in steady condition and its improvement compared to the start of adaptation are as follows: shoulder 0.96±2.53° (76%); elbow −0.35±0.81° (33%); hip 0.10±0.86° (38%); knee −0.19±0.67° (25%); and ankle −0.05±0.20° (60%). The presented simulation results verify the robustness of proposed adaptive method in cases that differ from our mathematical assumptions and indicate its potentials to be used in practice.

Quantitative Modeling of Spasticity for Clinical Assessment, Treatment and Rehabilitation

Spasticity, a common symptom in patients with upper motor neuron lesions, reduces the ability of a person to freely move their limbs by generating unwanted reflexes. Spasticity can interfere with rehabilitation programs and cause pain, muscle atrophy and musculoskeletal deformities. Despite its prevalence, it is not commonly understood. Widely used clinical scores are neither accurate nor reliable for spasticity assessment and follow up of treatments. Advancement of wearable sensors, signal processing and robotic platforms have enabled new developments and modeling approaches to better quantify spasticity. In this paper, we review quantitative modeling techniques that have been used for evaluating spasticity. These models generate objective measures to assess spasticity and use different approaches, such as purely mechanical modeling, musculoskeletal and neurological modeling, and threshold control-based modeling. We compare their advantages and limitations and discuss the recommendations for future studies. Finally, we discuss the focus on treatment and rehabilitation and the need for further investigation in those directions.

Cable-Driven Robotic Interface for Lower Limb Neuromechanics Identification

This paper presents a versatile cable-driven robotic interface to investigate the single-joint joint neuromechanics of the hip, knee and ankle in the sagittal plane. This endpoint-based interface offers highly dynamic interaction and accurate position control (as is typically required for neuromechanics identification), and provides measurements of position, interaction force and electromyography (EMG) of leg muscles. It can be used with the subject upright, corresponding to a natural posture during walking or standing, and does not impose kinematic constraints on a joint, in contrast to existing interfaces. Mechanical evaluations demonstrated that the interface yields a rigidity above 500 N/m with low viscosity. Tests with a rigid dummy leg and linear springs show that it can identify the mechanical impedance of a limb accurately. A smooth perturbation is developed and tested with a human subject, which can be used to estimate the hip neuromechanics.

A Clustering-Based Approach to Identify Joint Impedance During Walking

Mechanical impedance, which changes with posture and muscle activations, characterizes how the central nervous system regulates the interaction with the environment. Traditional approaches to impedance estimation, based on averaging of movement kinetics, requires a large number of trials and may introduce bias to the estimation due to the high variability in a repeated or periodic movement. Here, we introduce a data-driven modeling technique to estimate joint impedance considering the large gait variability. The proposed method can be used to estimate impedance in both the stance and swing phases of walking. A 2-pass clustering approach is used to extract groups of unperturbed gait data and estimate candidate baselines. Then patterns of perturbed data are matched with the most similar unperturbed baseline. The kinematic and torque deviations from the baselines are regressed locally to compute joint impedance at different gait phases. Simulations using the trajectory data of a subject's gait at different speeds demonstrate a more accurate estimation of ankle stiffness and damping with the proposed clustering-based method when compared with two methods: i) using average unperturbed baselines, and ii) matching shifted and scaled average unperturbed velocity baselines. Furthermore, the proposed method requires fewer trials than methods based on average unperturbed baselines. The experimental results on human hip impedance estimation show the feasibility of clustering-based technique and verifies that it reduces the estimation variability.