Optimising emulsion stability during processing of model infant formulae using factorial statistical design

Effect of different pretreatment methods on the stability of pumpkin seed milk and potential mechanism

Pumpkin seeds represent a valuable source of plant protein and can be utilized in the production of plant-based milks. This study aims to investigate the effects of different pretreatment techniques on the stability of Pumpkin Seed Milk (PSM) and explore potential mechanisms. Raw pumpkin seeds underwent pretreatment through roasting, microwaving, and steaming to prepare PSM. Physiochemical attributes such as composition, storage stability, and particle size of PSM were evaluated. Results indicate that stability significantly improved at roasting temperatures of 160 °C, with the smallest particle size (305 ± 40 nm) and highest stability coefficient (0.710 ± 0.002) observed. Nutrient content in PSM remained largely unaffected at 160 °C. Protein oxidation levels, infrared, and fluorescence spectra analysis revealed that higher temperatures exacerbated the oxidation of pumpkin seed emulsion. Overall, roasting raw pumpkin seeds at 160 °C is suggested to enhance PSM quality while preserving nutrient content.

Spray-Dried Infant Formula Emulsion Stability as Affected by Pre-Heat Treatment and Total Solids Content of the Feed

Pre-spray-drying processing may affect stability after reconstitution of emulsion-based powders, such as infant formulas. This study aimed to evaluate the effects of pasteurization temperature and total solids (TS) of the feed on the stability of the emulsions obtained from the reconstituted powders. Four infant formula powders (50%-75 °C, 50%-100 °C, 60%-75 °C, and 60%-100 °C) were produced at pilot scale, from emulsions with 50 or 60% TS pasteurized at 75 or 100 °C for 18 s. Both the emulsion feeds and the emulsions from the reconstituted powders (12.5% TS) were analyzed. The results showed that feeds with 60% TS were flocculated, as indicated by the large particle size and viscosity and the pseudoplastic behavior. Light microscopy revealed that, during spray drying, the flocs were disrupted in 60%-100 °C, while the 60%-75 °C emulsion remained flocculated, reducing its stability post-reconstitution. Although all four emulsions were mainly stabilized by caseins, the presence of β-lactoglobulin was also detected at the oil-water interface, in native state in the formulas preheated at 75 °C and aggregated in the formulas preheated at 100 °C. In conclusion, both the degree of whey protein denaturation (resulting from pasteurization) and the TS of the concentrates during infant formula production affected the emulsion stability of the reconstituted powders.

Emulsification properties of pea protein isolate using homogenization, microfluidization and ultrasonication

Pea protein isolate (PPI) is used in many food formulations, due to its low cost, commercial availability and excellent amino acid profile. The objective of this study was to determine the emulsification properties of PPI. Particle size of PPI powders showed neither temperature (25-65°C) nor time (up to 24h) increased solubilisation of powder particles during mixing. Heating PPI dispersions (10%, w/w, protein) from 45 to 90°C led to an increase in storage modulus (G'; Pa) at 71°C, indicating the onset of protein aggregation. Gel formation occurred at 79°C (G'>1Pa). Pea protein-stabilised emulsions made using homogenization (15MPa; 1 pass) or microfluidization (50MPa; 1 pass) resulted in the formation of cold-set gels, with gel strength increasing with increasing oil concentration and fluidic pressure. Droplet size and viscosity of pea protein-stabilised emulsions decreased and increased, respectively, with increasing ultrasonication time. Overall, ultrasonication (<50°C) can create a uniform droplet size emulsion, while, homogenization and microfluidization can produce cold-set gels for use in a wide-range of food applications.