Effect of ferrule height and glass fibre post length on fracture resistance and failure mode of endodontically treated teeth

Contemporary Concepts of Adhesive Cementation of Glass-Fiber Posts: A Narrative Review

(1) Background: Cementation of glass fiber posts to root canals has been associated with various failures, especially debonding. This narrative review aims to present the contemporary concepts concerning the adhesive cementation of glass fiber post and to discuss the optimal management of these factors. (2) Methods: Electronic search was performed in MEDLINE/Pub Med and Google Scholar using selected keywords examining the parameters post length, surface treatment of glass fiber posts, post space preparation and dentin pretreatment, resin cement selection, adhesive systems and hybrid layer formation, and clinical techniques. (3) Results: The search led to the selection of 44 articles. Epoxy resin-based endodontic sealers are recommended and the use of temporary cement in the root canal should be avoided. The minimum length of a glass fiber post adhesively cemented to a root canal is 5 mm. Irrigating the root canals with chlorhexidine, MTAD, or EDTA (alone or in combination with NaOCl) after post space preparation seems to enhance the bond strength. Silane application on the surface of the post seems to be beneficial. Concerning resin cements and adhesive systems, the results were rather inconclusive. Finally, resin cement should be applied inside the root canal with an elongation tip and photoactivation should be delayed. (4) Conclusions: Contemporary concepts of adhesive cementation of glass fiber posts can indeed improve the bond between glass fiber posts, resin cement, and root canal dentin, however, evidence coming from long-term randomized prospective clinical trials is needed in order to obtain safer conclusions.

The adhesive strength of fiber post-to-canal dentin with Aniline green, Fotoenticine activated by PDT, green tea, and ozone as a final irrigant

AIM

The effect of novel final disinfection protocols Malachite green (MG), Fotoenticine® (FTC), Green tea extract (GTE), and Ozonated water (OW) on the bond strength of prefabricated glass fiber posts (PGFP) adhered to canal dentin.

MATERIAL AND METHOD

The canals of fifty premolars with closed apices were cleansed and obturated. The specimens were randomly assigned to one of five groups based on the final irrigant used, with the control group receiving NaOCl+EDTA and the experimental groups receiving MG, FTC, OW, and GTE. The GFP was cemented with a self-etching, dual-cure paste; the bond strength was estimated with a universal testing machine; and failure analysis was conducted with a stereomicroscope.

RESULTS

The highest PBS was observed in the coronal third of Group 4 (using ozonated water as the final irrigant), whereas the lowest bond integrity was observed in the apical section of Group 2 (1.02-0.54 MPa) using Malachite green as the final irrigant. Group 1, Group 4, and Group 5 exhibited no significant difference in the bond integrity of GFP to dentin when compared to Group 2 (p>0.05). In addition, comparable bond score values were obtained for Groups 2 and 3 (p>0.05).

CONCLUSION

The results of this study suggest that OW and GTE may be effective final disinfectants for root canals, as they increase the bond strength of resin-luting cement.

Push-out bond strength of fiberglass posts cemented with adhesive and self-adhesive resin cements according to the root canal surface

Evaluating the bond strength of fiberglass posts cemented with different resin cements.

MATERIALS AND METHODS

Seventy freshly extracted roots of healthy human canines were endodontically treated and prepared to receive fiberglass posts. The roots were randomly divided into seven groups: (G1) RelyX ARC, (G2) Enforce, (G3) BisCem, (G4) Duo-Link, (G5) Cement Post, (G6) Variolink II, and (G7) RelyX U200. After post cementation, the specimens were sectioned perpendicularly to the root axis using a high-speed diamond disc, totaling 340 specimens. The strength values obtained in the push-out test were submitted to two-factor ANOVA and Tukey test (p = 0.05).

RESULTS

The root thirds (p = 0.001) and the type of cement (p = 0.001) influenced the bond strength values. The relation between these two factors was also significant (p = 0.011).

CONCLUSIONS

The bond strength of self-adhesive resin cements was significantly higher as compared to other cements. Besides the cervical third in roots cemented with conventional cements types presented the highest bond strength values (p < 0.05).

In Vitro Fracture Strength of Teeth Restored with Lithium Disilicate Onlays with and without Fiber Post Build-Up

To our knowledge there is no data about the mechanical performance of indirect restoration adhesively cemented on teeth without an adequate build-up to provide the correct geometrical configuration. The aim of this study was to compare the fracture strength of human teeth restored with lithium disilicate onlays, with and without fiber post build-up.

METHODS

Twenty human mandibular molars were horizontally sectioned and divided into two groups (n = 10). No treatment was applied in group A. Teeth in group B were endodontically treated, built-up using fiber post and composite core and prepared with a circumferential chamfer providing a 1 mm circumferential ferrule. Lithium disilicate onlays were pressed and luted on teeth using dual-curing luting composite. Teeth were tested under static load. Failures were classified as restorable or not restorable. Failure loads were analyzed with one-way analysis of variance. Failure modes were compared using Pearson's Chi-square tests.

RESULTS

The mean fracture loads were 1383.5 N for group A and 1286.3 N for group B. No difference was found (p = 0.6). Ninety per cent of fractures were classified as not restorable in both groups, with no difference (p = 0.8).

CONCLUSIONS

For teeth restored with adhesive procedures and lithium disilicate onlays, the presence of build-up with fiber post to provide retention and resistance form does not influence the fracture strength.

Fracture resistance and stress distribution of repairing endodontically treated maxillary first premolars with severe non-carious cervical lesions

This study was to compare the influence of glass fiber post placement and crown restoration on endodontically treated maxillary first premolars with severe NCCLs using three-dimensional finite element analysis and fracture resistance testing. G1, intact teeth. G2, teeth with artificial defect. G3, composite resin (CR). G4, CR and fiber post in buccal canal (FPB). G5, CR and fiber post in palatal canal (FPP). G6, CR and fiber posts in buccal and palatal canals (FPBP). G7, CR and crown (C). G8, CR, FPB, C. G9, CR, FPP, C. G10, CR, FPBP, C. Teeth in G2, G3, and G5 showed a similar stress concentration at the tip of the defect. The fracture resistance of G2 did not differ significantly from G3 and G5 (p>0.05) but differed significantly from that in other groups (p<0.05). The fractures in G4 were more favorable, and the difference of those in G1 from those in G7, G8, G9, and G10 was statistically significant (p<0.05). Restoration of root-filled maxillary premolars with severe NCCLs using fiber post in the buccal canal may be more efficacious than other restoration methods.

Influence of elastic modulus of intraradicular posts on the fracture load of roots restored with full crowns

Abstract Objective This study aimed to evaluate the fracture load and displacement of roots restored with posts of different elastic modulus. Material and method Thirty-six replicas of epoxy resin mixed with glass microfibers were made from an endodontically-treated human premolar root prepared to a length of 12 mm with a custom drill, leaving the apical 4 mm unprepared. Replicas were randomly restored with (n = 12): FP-LM (fiber post with low elastic modulus– 50 GPa), FP-HM (fiber post with high elastic modulus – 67 GPa) and MP (metallic post – 208 GPa), using self-curing adhesive and dual resin cement. Cores were built up with composite resin and metallic crowns were cemented in all the roots with self-adhesive resin cement with self-curing mode. Specimens were subjected to a fracture load test (45° inclination/0.5 mm/min) and displacement was registered at 100 N. Result One-way ANOVA showed that elastic modulus of the post did not affect the fracture load means (p = 0.203) (FP-LM: 237.4 ± 65.11 N; FP-HM: 236.7 ± 92.85 N; MP: 295.8 ± 108.7 N) but was statistically significant for the displacement (p < 0.00): Tukey’s test showed that FP-LM displacement mean (0.81 ± 0.15 mm) was significantly higher than those for FP-HM (0.46 ± 0.26 mm; p = 0.00) and MP (0.62 ± 0.07 mm; p = 0.04). Conclusion Posts with different elastic modulus exhibit similar fracture loads, but a lower displacement is achieved when fiber posts with a high elastic modulus and metallic posts are used.

Effect of fiber posts on the fracture resistance of endodontically treated anterior teeth with cervical cavities: An in vitro study

STATEMENT OF PROBLEM

How the placement of fiber posts affects the fracture resistance of endodontically treated maxillary central incisors with cervical cavities is not well documented.

PURPOSE

The purpose of this in vitro study was to evaluate the effect of fiber posts on the fracture resistance of endodontically treated maxillary central incisors with cervical cavities.

MATERIAL AND METHODS

Fifty extracted human maxillary central incisors were selected and divided into 5 test groups (n=10) according to the restoration strategy: GHT, control group; endodontically treated teeth (ETT) without endodontic posts; GCV, ETT with cervical cavities simulating coronal destruction; GCF, ETT with cervical cavities and carbon fiber posts; GGF, ETT with cervical cavities and glass fiber posts; and GCP, ETT with cervical cavities and composite resin posts. After the fiber posts had been cemented with a resin cement and the foundations had been placed, all specimens were quasi statically loaded at 45 degrees in a universal testing machine until fracture. All specimens were evaluated for fracture modes. The data were then analyzed by 1-way ANOVA, followed by multiple comparisons with the Tukey HSD test (α=.05). The mode of failure was determined by visual inspection.

RESULTS

The mean ±SD failure loads for the groups ranged from 718.2 ±89.8 N to 943.8 ±93.1 N. In a 1-way ANOVA followed by post hoc testing, GGFs had a higher fracture strength than all other groups (P≤.05). However, GCPs had a lower fracture strength than all other groups. Statistically significant differences were observed among groups (P≤.05), except between the GHT group and the GCF and GGF groups (P=.075, P=.226). All groups except GHT showed complete favorable fracture mode within the cervical third of the roots.

CONCLUSIONS

Within the limitations of this in vitro study, placement of glass fiber posts significantly improved the fracture resistance of endodontically treated maxillary central incisors with cervical cavities.