Relationship between the CT Value and Cortical Bone Thickness at Implant Recipient Sites and Primary Implant Stability with Comparison of Different Implant Types

Correlation of two different devices for the evaluation of primary implant stability depending on dental implant length and bone density: An in vitro study

Non-invasive objective implant stability measurements are needed to determine the appropriate timing of prosthetic fitting after implant placement. We compared the early implant stability results obtained using resonance frequency analysis (RFA) and damping capacity analysis (DCA) depending on the implant length and bone density. Total 60, 4.0 mm diameter implants of various lengths (7.3 mm, 10 mm, and 13 mm) were used. In Group I, low-density bone was described using 15 PCF (0.24 g/cm3) polyurethane bone blocks, and in Group II, 30 PCF (0.48 g/cm3) polyurethane bone blocks were used to describe medium density bone. RFA was performed using an Osstell® Beacon+; DCA was performed using Anycheck®. Measurements were repeated five times for each implant. Statistical significance was set at P <0.05. In Group I, bone density and primary implant stability were positively correlated, while implant length and primary implant stability were positively correlated. In Group II, the implant stability quotient (ISQ) and implant stability test (IST) values in did not change significantly above a certain length. Primary implant stability was positively correlated with bone density and improved with increasing implant length at low bone densities. Compared with the Osstell® Beacon+, the simplicity of Anycheck® was easy to use and accessible.

The clinical efficacy of autogenous dentin blocks prepared chairside for alveolar ridge augmentation: A systematic review and meta-analysis

OBJECTIVES

This systematic review aimed to evaluate the current evidence on the effectiveness of autogenous dentin block graft prepared chairside for alveolar ridge augmentation and compare its clinical outcomes to the main available grafting materials and techniques.

MATERIALS AND METHODS

Three databases were screened, including prospective clinical studies, utilizing autogenous dentin blocks for ridge augmentation, with at least 3 months of postoperative follow-up.

RESULTS

Eight articles were included, and four of them were meta-analyzed. Dentin blocks demonstrated similar vertical bone gain and significantly higher width gain, compared to bone blocks (WMD = 0.03, 95% CI -0.51 to 0.57, p = .92 and WMD = 1.34, 95% CI 0.57 to 2.12, p = .0007, respectively). Vertical and horizontal resorption were similar between the two groups (WMD = -0.36, 95% CI -0.91 to 0.18, p = .19, and WMD = -0.47, 95% CI -1.05 to 0.11, p = .11, respectively). Dentin blocks showed more incidences of postoperative complications, however, with no statistical significance (RR = 4.30, 95% CI 0.97 to 18.96, p = .054). The need for additional augmentation upon implant placement was also similar between both grafts (RR = 0.95, 95% CI 0.39 to 2.28, p = .90). Recorded incidences of graft exposure were low (2.27%), and no study stated surgical site infection.

CONCLUSION

Within its limitations, this study indicates that the autogenous dentin blocks prepared chairside could be a possible alternative to the other established bone augmentation techniques for staged ridge augmentation. Nevertheless, future studies are needed to confirm its efficacy and implant success/survival in sites grafted with this material.

Correlation between Primary, Secondary Stability, Bone Density, Percentage of Vital Bone Formation and Implant Size

BACKGROUND

This study aims to evaluate whether there is a correlation between implant stability, bone density, vital bone formation and implant diameter and length.

METHODS

Ninety patients were enrolled in this study. They underwent a socket preservation procedure with allograft or PRF and after 4 months, a total of 90 implants were placed. CBCT scans were assigned prior to implant placement in order to assess the bone density. During the surgical re-entry, a bone biopsy was harvested with a trephine drill. Immediately after implant insertion, the primary stability was measured. The secondary stability was measured 4 months after implant placement.

RESULTS

Primary stability showed a significant positive linear correlation with bone density (r = 0.471, p < 0.001) as well as with percentage of new bone formation (r = 0.567, p < 0.001). An average significant association of secondary stability with bone density (rs = 0.498, p < 0.001) and percentage of newly formed bone (r = 0.477, p < 0.001) was revealed. The mean values of primary stability in all three implant sizes, regarding the diameter of the implants, were similar (narrow 67.75; standard 66.78; wide 71.21) with no significant difference (p = 0.262). The same tendency was observed for secondary stability (narrow 73.83; standard 75.25; wide 74.93), with no significant difference (p = 0.277).

CONCLUSIONS

The study revealed a high correlation between primary and secondary implant stability, and bone density, as well as with the percentage of vital bone formation. Implant length and diameter revealed no linear correlation with the implant stability.

The Digital Abutment Check: An Improvement of the Fully Digital Workflow

By using modern digitalization techniques, an existing denture can be digitized and aid the provision of a new implant-supported denture according to a fully digital workflow. This includes fully navigated implant surgery and results in an immediately provided prosthetic restoration. However, even with the current digital workflow, it is challenging to achieve a definitive prosthetic restoration in a single treatment session. In order to achieve a definitive denture in as few treatment sessions as possible, we have implemented the digital abutment test. This test modified the existing data set and determined the final restoration. In the present case, the preexisting maxillary removable complete denture was converted into a fixed immediate restoration using the fully digital workflow. The workflow is divided into two treatment phases, each with three treatment sessions, where part of the second phase involves an innovative digital abutment check. The illustrated case shows an effective use of current digital possibilities. Special attention was also paid to a minimally invasive course of therapy.

Is there any predictive bone parameter for implant stability in 2-dimensional and 3-dimensional radiologic images?

OBJECTIVES

This ex vivo study aimed to compare radiomorphometric parameters between 2-dimensional (2-D) and 3-dimensional (3-D) radiographs and evaluate the influence of preoperative radiologic bone parameters on the clinical outcomes of implant stability.

STUDY DESIGN

Implant recipient sites in fresh bovine blocks were evaluated on panoramic radiographs for gray value (GV), fractal dimension (FD), number of connected trabeculae (Co), and density of connected trabeculae (CoD). Cone beam computed tomography (CBCT) scans were evaluated for trabecular thickness (TbTh), cortical thickness (CTh), degree of anisotropy (DA), FD, and Co. Insertion torque (IT) and implant stability quotient (ISQ) were measured.

RESULTS

GV was significantly correlated with all parameters in 2-D and 3-D images except FD in 2-D and Co in 3-D, and with all surgical parameters (P ≤ .029). Co and CoD values on panoramic radiographs had significant correlation with TbTh, CTh, and DA values on CBCT images (P < .001). All 2-D parameters and TbTh and CTh in the CBCT data were significantly correlated with IT only (P ≤ .047). Only GV was correlated with ISQ measurements (P ≤ .029).

CONCLUSIONS

GV, Co, and CoD values on panoramic radiographs reflect the architecture of trabecular bone and the thickness of cortical bone, and might help predict implant stability in clinical situations.

The clinical significance of implant stability quotient (ISQ) measurements: A literature review

Implant stability quotients (ISQ values) are obtained in dental clinical practice on a non-invasive basis by resonance frequency measurement rapidly after surgical placement of implants. The ISQ-values are used as indicator for mechanical implant stability, and are believed to have predictive power for clinical outcome. It is the aim of this review to provide a synopsis of all factors described in the literature that influence ISQ measurements by performing an exhaustive literature review; moreover, this review aims at elucidating the key factors relevant for a rapid clinical predictive assessment. We searched systematically and exhaustively all major databases for publications relating to ISQ measurement methodology and for ISQ-influencing factor analyses. The reports identified were ordered in experimental (preclinical) studies and in clinical publications. We were able to identify 13 basic factors influencing ISQ-measurements. Among these, local bone quality, playing a key role in such measurements, was subdivided in four specific subfactors; thus a total of 17 individual factors was identified and reported to influence ISQ-measurements. A comprehensive list of these factors is provided in Table-form. A critical analysis points out that only 6 of these factors are of a sound predictive power useful for a rapid clinical assessment; and only two of these factors appear to have a well-documented scientific basis.

Bone Density and Implant Primary Stability. A Study on Equine Bone Blocks

Previous results on synthetic blocks mimicking bone indicate that bone density can be measured by the friction encountered by a rotating probe while it descends into bone, and that primary implant stability may be measured through the integral (I) of the torque–depth curve at implant insertion. This study aims to repeat those tests on collagen-preserving equine bone blocks as they better reproduce the mechanical properties of natural bone. Fifteen cancellous equine blocks had their density measured using a measuring probe. This was compared to their known physical density through linear regression analysis. Implant placement was carried out into six cancellous equine blocks and primary stability was measured using (I), as well as the insertion torque (IT), the implant stability quotient (ISQ), and the reverse torque (RT). The relation between (I), (IT), (ISQ), and (RT) was investigated by correlation analysis. Bone density measured using the probe correlated significantly with actual density, both with (r = 0.764) and without irrigation (r = 0.977). (I) correlated significantly with IT and RT under all irrigation conditions, and with ISQ only without irrigation (r = 0.886). The results suggest that the probe provides actual bone density measurements. They also indicate that (I) measures primary implant stability and is more sensitive to density variations than IT, RT, and ISQ. Results are consistent with those obtained on synthetic blocks but suggest that equine bone blocks may better reproduce the mechanical properties of human cancellous alveolar bone. This should be the subject of additional studies.

Comparison of ground sections, paraffin sections and micro-CT imaging of bone from the epiphysis of the porcine femur for morphometric evaluation

The aim of this study was to compare data on the volume fraction of bone and the thickness of the cortical compact bone acquired during microcomputed tomography (micro-CT) analysis with data acquired from identical samples using stereological analysis of either decalcified paraffin sections or ground sections. Additionally, we aimed to compare adjacent tissue samples taken from the major trochanter of the porcine femur to map the basic biological variability of trabecular bone. Fifteen pairs of adjacent tissue blocks were removed from the major trochanter of the proximal epiphyses of porcine femurs (female pigs aged 24-39 months, weight=59.16±8.15kg). In each sample, the volume of the cortical compact bone, the volume of the trabecular bone, and the thickness of the cortical compact bone was assessed using micro-CT. Afterwards, half of the samples were decalcified and processed using paraffin histological sections. Another half was processed into ground sections. The volume and thickness of bone was assessed in histological sections using stereological techniques. There were no significant differences in the bone volumes and thicknesses measured by micro-CT and the corresponding values quantified in decalcified sections. Similarly, there were no differences between the results from micro-CT and the analysis of the corresponding ground sections. Histomorphometric studies based on relatively low numbers of undecalcified ground sections or demineralized paraffin sections of bone yield data on bone volume and the thickness of cortical compact bone that is comparable with three-dimensional micro-CT examination. The pilot data on the variability of cortical compact bone and trabecular bone volumes in the porcine major trochanter provided in this study aim for planning experiments in the field of bone healing and implantology.

A numerical investigation and experimental verification of size effects in loaded bovine cortical bone

In this paper, we present 2- and 3-dimensional finite element-based numerical models of loaded bovine cortical bone that explicitly incorporate the dominant microstructural feature: the vascular channel or Haversian canal system. The finite element models along with the representation of the microstructure within them are relatively simple: 2-dimensional models, consisting of a structured mesh of linear elastic planar elements punctuated by a periodic distribution of circular voids, are used to represent beam samples of cortical bone in which the channels are orientated perpendicular to the sample major axis, while 3-dimensional models, using a corresponding mesh of equivalent solid elements, represent those samples in which the canals are aligned with the axis. However, these models are exploited in an entirely novel approach involving the representation of material samples of different sizes and surface morphology. The numerical results obtained for the virtual material samples when loaded in bending indicate that they exhibit size effects not forecast by either classical (Cauchy) or more generalized elasticity theories. However, these effects are qualitatively consistent with those that we observed in a series of carefully conducted experiments involving the flexural testing of bone samples of different sizes. Encouraged by this qualitative agreement, we have identified appropriate model parameters, primarily void volume fraction but also void separation and matrix modulus by matching the computed size effects to those we observed experimentally. Interestingly, the parameter choices that provide the most suitable match of these effects broadly concur with those we actually observed in cortical bone.

Effects of implant tilting and the loading direction on the displacement and micromotion of immediately loaded implants: an in vitro experiment and finite element analysis

Purpose

The purpose of this study was to investigate the effects of implant tilting and the loading direction on the displacement and micromotion (relative displacement between the implant and bone) of immediately loaded implants by in vitro experiments and finite element analysis (FEA).

Methods

Six artificial bone blocks were prepared. Six screw-type implants with a length of 10 mm and diameter of 4.3 mm were placed, with 3 positioned axially and 3 tilted. The tilted implants were 30° distally inclined to the axial implants. Vertical and mesiodistal oblique (45° angle) loads of 200 N were applied to the top of the abutment, and the abutment displacement was recorded. Nonlinear finite element models simulating the in vitro experiment were constructed, and the abutment displacement and micromotion were calculated. The data on the abutment displacement from in vitro experiments and FEA were compared, and the validity of the finite element model was evaluated.

Results

The abutment displacement was greater under oblique loading than under axial loading and greater for the tilted implants than for the axial implants. The in vitro and FEA results showed satisfactory consistency. The maximum micromotion was 2.8- to 4.1-fold higher under oblique loading than under vertical loading. The maximum micromotion values in the axial and tilted implants were very close under vertical loading. However, in the tilted implant model, the maximum micromotion was 38.7% less than in the axial implant model under oblique loading. The relationship between abutment displacement and micromotion varied according to the loading direction (vertical or oblique) as well as the implant insertion angle (axial or tilted).

Conclusions

Tilted implants may have a lower maximum extent of micromotion than axial implants under mesiodistal oblique loading. The maximum micromotion values were strongly influenced by the loading direction. The maximum micromotion values did not reflect the abutment displacement values.

The Effect of Osteotomy Dimension on Implant Insertion Torque, Healing Mode, and Osseointegration Indicators: A Study in Dogs

PURPOSE

This study investigated the effect of the osteotomy diameter for implant placement torque and its effect on the osseointegration.

MATERIALS AND METHODS

Eight male beagle dogs received 48 implants (3.75 mm × 10 mm) in their right and left radius, 3 implants per side and allowed to heal for 3 weeks. Three experimental groups were evaluated. Group 1: implant with an undersized osteotomy of 3.0 mm; group 2: osteotomy of 3.25 mm, and group 3: osteotomy of 3.5 mm. The insertion torque was recorded for all implants. Histological sectioning and histometric analysis were performed evaluating bone-to-implant contact (BIC) and bone area fraction occupancy (BAFO).

RESULTS

Implants of group 1 presented statistically higher insertion torque than those of groups 2 and 3 (P < 0.01). No differences in BIC or BAFO were observed between the groups. From a morphologic standpoint, substantial deviations in healing mode were observed between groups.

CONCLUSION

Based on the present methodology, the experimental alterations of surgical technic can be clinically used with no detrimental effect over the osseointegration process.