Autologous bone harvested during implant bed preparation: A randomized clinical trial comparing high-speed drilling with irrigation versus low-speed drilling without irrigation

OBJECTIVE

To compare collected bone weight and the frequency of autologous bone harvesting from the flutes of surgical drills used for implant bed preparation using two different drilling techniques. A comparative evaluation of radiographic bone density and bone quality was also made.

MATERIALS AND METHODS

A randomized clinical trial was made of 66 dental implants in patients with a single posterior edentulous site. The compared drilling techniques were high-speed drilling with irrigation (control group) and low-speed drilling without irrigation (test group). The bone collected in both groups was dried and weighed with a precise electronic balance. The frequency of harvesting was calculated. The median radiographic bone density of each implant site was measured using cone-beam computed tomography (CBCT) pixel values. Patient sex, age, implant position and dimensions, as well as the last drill diameter were analyzed as independent variables. The level of significance was 5%.

RESULTS

The harvesting of bone chips from drill flutes proved possible in 51.5% of the procedures in the control group and in 100% in the test group (p < 0.001). There were also statistically significant differences in bone weight between the control group (6.7 ± 10.6 mg) and the test group (41.9 ± 30.3 mg) (p < 0.001). The CBCT pixel values were directly correlated with the collected bone weight in both groups. The median radiographic bone density, arch and last drill diameter were significantly associated with harvesting bone frequency and collected bone weight (p < 0.05).

CONCLUSIONS

Our findings suggest that the frequency and weight of autologous bone harvested from drills are greater with low-speed drilling without irrigation than with high-speed drilling with irrigation. Radiographic bone density, arch and last drill diameter also significantly influenced the harvesting outcomes.

Dimensional ridge changes in conjunction with four implant timing protocols and two types of soft tissue grafts: A pilot pre-clinical study

AIM

To determine the effect of (1) implant placement timing and (2) the type of soft tissue graft in terms of ridge profile changes.

MATERIALS AND METHODS

Four implant treatment modalities were applied in the mesial root areas of the third and fourth mandibular premolars of 10 mongrel dogs alongside connective-tissue graft (CTG) and volume-stable cross-linked collagen matrix (VCMX): immediate, early, and delayed placement (DP), and DP following alveolar ridge preservation (ARP). All dogs were sacrificed 3 months after soft tissue augmentation. Standard Tessellation Language files from designated time points were analysed.

RESULTS

Compared with the pre-extraction situation, the median width of the ridge demontstrated a linear increase only in group ARP/CTG (0.07 mm at the 2-mm level), whereas all other groups showed a reduction (between -1.87 and -0.09 mm, p > .05). Groups ARP/CTG (0.17 mm) and DP/CTG (0.05 mm) exhibited a profilometric tissue gain in a set region of interest (p > .05). The net effect of CTG and VCMX ranged from 0.14 to 0.79 mm.

CONCLUSIONS

Dimensional ridge changes varied between treatment protocols. ARP with CTG led to the smallest difference in ridge profile between the pre-extraction and the study end time point. Both CTG and VCMX enhanced the ridge contour.

Addition of autogenous bone chips to deproteinized bovine bone mineral does not have additional benefit in lateral ridge augmentation-A preclinical in vivo experimental study

OBJECTIVE

To compare the outcome after extensive lateral guided bone regeneration using deproteinized bovine bone mineral (DBBM) with or without autogenous bone chips in a canine model of chronic horizontal alveolar ridge defect.

MATERIALS AND METHODS

The second, third and fourth lower premolars of both sides were extracted, and the buccal bone walls were completely removed in five beagle dogs. After 4 weeks, DBBM particles mixed with autogenous bone chips at a ratio of 1:1 were grafted at one side (DBBM/Auto group), while DBBM particles alone were grafted at the contralateral side (DBBM group). The graft materials on both sides were covered by a resorbable collagen membrane and fixation pins. Microcomputed tomographic volume and histomorphometric analyses were performed at 16 weeks post-surgery.

RESULTS

The ridges of both groups were recovered horizontally, but new bone formation beyond the original ridge contour at the defect site was not found. The DBBM group exhibited a larger total radiographic augmented volume and new bone volume compared with the DBBM/Auto group, but the differences were minimal (p > .05). Histologically, the regenerated area and new bone area were also slightly larger without any statistical significance in the DBBM group than in the DBBM/Auto group (p > .05).

CONCLUSION

The addition of autogenous bone chips to DBBM for lateral ridge augmentation may confer no advantage over grafting DBBM alone with respect to both space maintenance and de novo bone formation in dogs.

Alveolar crest contour changes after guided bone regeneration using different biomaterials: an experimental in vivo investigation

OBJECTIVE

To evaluate the changes in alveolar contour after guided bone regeneration (GBR) with two different combinations of biomaterials in dehiscence defects around implants.

MATERIAL AND METHODS

Chronic alveolar ridge defects were created bilaterally in the mandible of eight Beagle dogs. Once implants were placed, three treatment groups were randomly allocated to each peri-implant dehiscence defect: (i) test group received a bone substitute composed of hydroxyapatite (HA) and β-tricalcium phosphate (β-TCP) covered by a cross-linked collagen membrane, (ii) positive control group with placement of deproteinized bovine bone mineral (DBBM) plus a porcine natural collagen membrane, and (iii) a negative control with no treatment. Two healing periods (8 and 16 weeks) were evaluated. Dental casts were optically scanned, the obtained files were uploaded into an image analysis software and superimposed to evaluate the linear changes.

RESULTS

In both healing periods, the gains in linear contours were higher in the test group and at the intermediate level (3 mm below the gingival margin). While at 8 weeks, no significant differences were found between the groups; at 16 weeks, the test and positive control groups demonstrated significant gains in contour compared with negative control.

CONCLUSIONS

GBR using different biomaterials significantly increased the buccal contours of the alveolar crest when used at dehiscence defects around dental implants.

CLINICAL RELEVANCE

Particulate highly porous synthetic bone substitute and a cross-linked collagen membrane demonstrated similar outcomes in terms of contour augmentation when compared to bovine xenograft (DBBM) and a collagen membrane.

Guided bone regeneration using beta-tricalcium phosphate with and without fibronectin-An experimental study in rats

OBJECTIVE

This histomorphometric study compared bone regeneration potential of beta-tricalcium phosphate with fibronectin (β-TCP-Fn) in critical-sized calvarial defects (CSDs) in rats to assess whether fibronectin (Fn) improved new bone formation.

MATERIAL AND METHODS

Critical-sized calvarial defects were created in 30 adult male Sprague Dawley rats, which were divided into four groups according to the time of euthanasia (6 or 8 weeks of healing) and type of filling (β-TCP-Fn/6 weeks, β-TCP/6 weeks, β-TCP-Fn/8 weeks and β-TCP/8 weeks). The primary variables related to new bone formation were augmented area (AA) and gained tissue (GT; sum of mineralized bone matrix [MBM] and bone substitute [BS]). Secondary variables were the diameter of the defect, MBM, non-mineralized tissue (NMT) and BS.

RESULTS

A total of 29 rats and 58 histological samples were evaluated, 28 (48.3%) samples obtained at 6 weeks and 30 (51.7%) at 8 weeks, homogeneously distributed between right and left sides. Thirteen (22.4%) were treated with β-TCP-Fn, 16 (27.6%) with β-TCP and 29 (50%) were controls. At 8 weeks, histomorphometric analysis showed significant differences in AA using β-TCP and β-TCP-Fn versus controls (p = 0.001 and p = 0.005, respectively). Bone turnover expressed as % within the target area was slightly higher but not statistically significant in the β-TCP-Fn than in β-TCP (MBM) at 6 weeks versus 8 weeks (p = 0.067 and p = 0.335, respectively). Finally, the total GT area in mm² was higher using β-TCP-Fn as compared to β-TCP (p = 0.044).

CONCLUSIONS

β-TCP-Fn was slightly but non-significantly more effective than β-TCP without Fn for improving the volume of regenerated bone in CSDs of rats, possibly allowing a more efficient bone remodelling process. This effect however should continue being investigated.

Bone Regeneration of Peri-Implant Defects Using a Collagen Membrane as a Carrier for Recombinant Human Bone Morphogenetic Protein-2

This study is designed to determine the effect of collagen membrane (CM) soaked with bone morphogenetic protein-2 (rhBMP-2) for the treatment of peri-implant dehiscence defects. Material and Methods. Three treatment groups were allocated at each defect in 5 dogs: (i) collagenated synthetic bone (OC) and CM soaked with rhBMP-2 (BMP group), (ii) OC and CM soaked with saline (nonBMP group), and (iii) no further treatment (control group). Titanium pins were used to stabilize the membranes in two dogs. Radiographic and histomorphometric analyses were performed 4 weeks later. Results. The median augmented volumes were 4.27 mm³, 6.24 mm³, and 2.75 mm³ in the BMP, nonBMP, and control groups, respectively; the corresponding median first bone-to-implant contact (fBIC) distances were 3.25 mm, 3.08 mm, and 2.56 mm (P > 0.05). The placement of pins (with the BMP and nonBMP groups pooled) significantly improved bone regeneration: the augmented volumes were 17.60 mm³ with pins and 3.68 mm³ without pins (P = 0.024), with corresponding fBIC distances of 2.25 mm and 3.31 mm, respectively (P < 0.001). Conclusions. The addition of rhBMP-2 to CM failed to improve bone regeneration of peri-implant dehiscence defects compared to using an unsoaked CM after 4 weeks. However, the stabilization of CMs using pins positively influenced the outcomes.

Comparison of the Bone Harvesting Capacity of an Intraoral Bone Harvesting Device and Three Different Implant Drills

The aim of the present study was to compare bone-collecting capacity of bone harvesting device and minimally irrigated low-speed drilling using three implant systems. One bone harvesting device and three commercially available drill systems were compared using the osteotomies on bovine rib bones. The amount of the collected bone particle and particle size (<500 μm: small, 500–1000 μm: medium, and >1000 μm: large) were measured. Total wet (1.535 ± 0.232 mL) and dry volume (1.147 ± 0.425 mL) of the bone particles from bone harvesting device were significantly greater than three drill systems (wet volume: 1.225 ± 0.187–1.27 ± 0.29 mL and dry volume: 0.688 ± 0.163–0.74 ± 0.311 mL) (P < 0.05). In all groups, the amount of large sized particles in wet and dry state was the greatest compared to that of medium and small particles. The dry weight of the bone particles showed the same tendency to volumetric measurement. In conclusion, total bone particles and large sized particles (>1000 μm) were harvested significantly greater by bone harvesting device than minimally irrigated low-speed drilling. The composition of particle size in all harvesting methods was similar to each other.

Bone augmentation at peri-implant dehiscence defects comparing a synthetic polyethylene glycol hydrogel matrix vs. standard guided bone regeneration techniques

OBJECTIVES

The aim of the study was to test whether or not the use of a polyethylene glycol (PEG) hydrogel with or without the addition of an arginylglycylaspartic acid (RGD) sequence applied as a matrix in combination with hydroxyapatite/tricalciumphosphate (HA/TCP) results in similar peri-implant bone regeneration as traditional guided bone regeneration procedures.

MATERIAL AND METHODS

In 12 beagle dogs, implant placement and peri-implant bone regeneration were performed 2 months after tooth extraction in the maxilla. Two standardized box-shaped defects were bilaterally created, and dental implants were placed in the center of the defects with a dehiscence of 4 mm. Four treatment modalities were randomly applied: i)HA/TCP mixed with a synthetic PEG hydrogel, ii)HA/TCP mixed with a synthetic PEG hydrogel supplemented with an RGD sequence, iii)HA/TCP covered with a native collagen membrane (CM), iv)and no bone augmentation (empty). After a healing period of 8 or 16 weeks, micro-CT and histological analyses were performed.

RESULTS

Histomorphometric analysis revealed a greater relative augmented area for groups with bone augmentation (43.3%-53.9% at 8 weeks, 31.2%-42.8% at 16 weeks) compared to empty controls (22.9% at 8 weeks, 1.1% at 16 weeks). The median amount of newly formed bone was greatest in group CM at both time-points. Regarding the first bone-to-implant contact, CM was statistically significantly superior to all other groups at 8 weeks.

CONCLUSIONS

Bone can partially be regenerated at peri-implant buccal dehiscence defects using traditional guided bone regeneration techniques. The use of a PEG hydrogel applied as a matrix mixed with a synthetic bone substitute material might lack a sufficient stability over time for this kind of defect.

Room-temperature fabrication of a three-dimensional reduced-graphene oxide/polypyrrole/hydroxyapatite composite scaffold for bone tissue engineering

The development of tissue engineering (TE) provides a promising alternative strategy for bone healing and regeneration.