Comparative study on the shaping ability and cleaning efficiency of rotary Mtwo instruments. Part 2. Cleaning effectiveness and shaping ability in severely curved root canals of extracted teeth

Efficacy of different irrigant activation techniques for cleaning root canal anastomosis

OBJECTIVE

This study compared in vitro the anastomosis cleaning efficacy of different irrigant activation techniques at different levels; control group non-activation (NA), passive ultrasonic irrigation (PUI) using Irrisafe, and EDDY sonic activation.

METHODS

Sixty anastomosis-containing mesial roots of mandibular molars were mounted in resin, sectioned at 2, 4, and 6 mm from the apex. Then reassembled and instrumented in a copper cube. For the irrigation technique roots were randomly divided into 3 groups (n = 20): group 1: NA, group 2: Irrisafe, group 3: EDDY. Stereomicroscopic images of anastomoses were taken after instrumentation and after irrigant activation. ImageJ program was used to calculate the percentage of anastomosis cleanliness. The percentage of cleanliness was calculated before and after final irrigation within each group and were then compared using paired t-tests. Intergroup and intragroup analyses were performed to compare between different activation techniques at the same root canal level (2, 4 and 6 mm) (intergroup) and to evaluate if each technique had different cleanliness efficacy according to the root canal level (intragroup) using one-way analysis of variance and post hoc tests (p < 0.05).

RESULTS

All three irrigation techniques significantly improved anastomosis cleanliness (p < 0.001). Both activation techniques were significantly better than the control group at all levels. Intergroup comparison revealed that EDDY significantly achieved the best overall anastomosis cleanliness. The difference between EDDY and Irrisafe was significant in favor to EDDY at 2 mm and insignificant at 4 and 6 mm. The intragroup comparison showed that improvement in anastomosis cleanliness (i2-i1) in the needle irrigation without activation group (NA) was significantly higher in the apical 2 mm level compared to the 4 & 6 levels. While the difference in anastomosis cleanliness improvement (i2-i1) between levels in both Irrisafe and EDDY groups was insignificant.

CONCLUSIONS

Irrigant activation improves anastomosis cleanliness. EDDY was the most efficient in cleaning anastomoses located in the critical apical part of the root canal.

CLINICAL RELEVANCE

Cleaning and disinfection of the root canal system followed by apical and coronal sealing is the key for healing or prevention of apical periodontitis. Remnants of debris and microorganisms retained within the anastomoses (isthmuses), or other root canal irregularities may lead to persistent apical periodontitis. Proper irrigation and activation are essential for cleaning root canal anastomoses.

Shaping ability of rotary and reciprocating single-file systems in combination with and without different glide path techniques in simulated curved canals

Background/purpose

Materials and methods

Results

Conclusion

Transportation and Centering Ability of Kedo-S Pediatric and Mtwo Instruments in Primary Teeth: A Cone-beam Computed Tomography Study

Background

Cleaning and debriding the canals and preserving the shape of the canal without deformation is the primary goals of pulpectomy. Transportation is a critical endodontic iatrogenic fault that could cause a catastrophe. This study evaluated the canal centering ability and canal transportation caused by Kedo-S pediatric and Mtwo instruments, using a cone-beam computed tomography (CBCT).

Materials and methods

This in vitro study was performed on distal roots of 50 primary mandibular first molars. The teeth were scanned using CBCT and randomly divided into two groups. The canals were then prepared using either Kedo-S or Mtwo files (n = 25). The instrumented canals were rescanned. The scanned volumes were sectioned at 2, 4, and 6 mm from cementoenamel junction (CEJ). Canal transportation (CT) and instrument centering ability were estimated and compared in both groups.

Results

The mean values for two study groups were compared. T -test was used to determine theP value. The Levene's test was used to test the significance between two groups. The two groups showed similar results in terms of transportation and centering ability (P > 0.05).

Conclusion

Kedo-S pediatric and Mtwo instruments demonstrated similar canal centering ability and CTs.

How to cite this article

Haridoss S, Rakkesh KM, Swaminathan K. Transportation and Centering Ability of Kedo-S Pediatric and Mtwo Instruments in Primary Teeth: A Cone-beam Computed Tomography Study. Int J Clin Pediatr Dent 2022;15(S-1):S30-S34.

Computed Tomographic Assessment of Remaining Dentin and Risk of Perforation after Kedo-S and Mtwo Rotary Instrumentation in Root Canals of Primary Teeth: An In Vitro Study

Background

Root canal cleaning is a key step in the endodontic treatment of the primary molars. An innovative generation of endodontic instruments has been devised with the aim of emerging better procedures. The objective of the study is to assess the preparation of time, the risk of lateral perforation, and the removal of dentin from Kedo-S and Mtwo rotary instruments on primary teeth.

Study design

This is an in vitro experimental study comparing the two groups.

Materials and methods

A total of 50 extracted mandibular primary first molars are collected, divided randomly into two groups of 25 teeth each. Group I: Kedo-S Pediatric rotary file, Group II: Mtwo rotary file. Distal canal is standardized for evaluation and teeth are sectioned at the CEJ. The teeth were instrumented according to manufacturer's guideline. Both the groups are scanned before and after instrumentation of the canal using cone-beam computed tomography (CBCT) and values are evaluated.

Results

Compared with Mtwo files, Kedo-S files need less instrumentation time and limited lateral perforation. No statistical differences were reported between the instrumentation of Kedo-S and Mtwo with regard to the amount of dentin removed.

Conclusion

In pediatric endodontics, Kedo-S pediatric rotary file can be considered an effective alternative to traditional rotary files because it requires less instrumentation time and preserves dentin thickness.

How to cite this article

Swaminathan K, Rakkesh KM, Haridoss S. Computed Tomographic Assessment of Remaining Dentin and Risk of Perforation after Kedo-S and Mtwo Rotary Instrumentation in Root Canals of Primary Teeth: An In Vitro Study. Int J Clin Pediatr Dent 2022;15(S-1):S87-S91.

Shaping ability of ProTaper Gold and WaveOne Gold nickel-titanium rotary instruments in simulated S-shaped root canals

Background/purpose

Gold metal technology improves flexibility and the resistance to cyclic fatigue of the endodontic mechanical files. This study compared the performance of ProTaper Gold (PTG) multiple file system and WaveOne Gold (WOG) single file system in simulated S-shaped root canals, which represents one of the most challenging root canal morphology.

Materials and methods

Forty S-shaped canals (n = 20 canals/per group) in resin blocks were instrumented to an apical size of 0.25 mm using PTG and WOG Primary, respectively. The total amount of resin removal, canal transportation, centering ratio, and the degree of canal straightening were measured in Photoshop CS6 software. Statistical analysis was performed by using Mann–Whitney U-test (α = .05).

Results

None of the files fractured during the instrumentation. The WOG group removed significantly less amount of resin at 0, 3, 6, 7 and 9 mm from the apex (P < .05). The WOG group remained more centered in canals at 0 mm from the apex (P < .05). The PTG group showed a better centering ability and less canal transportation at 4, 5 and 6 mm from the apex (P < .05). In the coronal curvature portion, the use of WOG Primary significantly decreased curvature angle and increased radius compared with PTG instruments (P < .05). There was no significant difference between the two groups in terms of the apical curvature angle and radius change (P > .05).

Conclusion

The WOG Primary file has a less aggressive dentin cutting and more centered apical preparation. The PTG system is more advantageous in shaping the coronal curvature of S-shaped canal.

Longitudinal craze line propagation in human root dentin after instrumentation with NiTi rotary files of different instrument tapers after long-term chewing simulation

Objectives

The aim of this study was to investigate whether file design and taper significantly influence microcrack initiation during machine preparation.

Materials and methods

Sixty extracted teeth with straight single canals were selected. The teeth were randomly assigned to four groups based on their root canal anatomy and the corresponding NiTi rotary file system (I, Mtwo; II, ProTaper Universal; III, F6 SkyTaper; control, no preparation and filling). The root canals of the experimental groups were filled using the single-cone technique. The tested teeth were all subjected to a mechanical chewing simulation with flat lead loading over a period of 3 years (corresponding to 150,000 cycles). The teeth were checked for dentinal defects (accumulative crack growth in length) under the digital microscope (Keyence VHX-5000) at time 0 (baseline prior to chewing simulation) and after 3, 6, 12, 24, and 36 months of loading. The cumulative crack increase was statistically analyzed using the Kruskal–Wallis test, Jonckheere–Terpstra test, and the Wilcoxon rank-sum test. The significance was set at p < 0.05.

Results

In contrast to preparation with greater-tapered instruments, ProTaper Universal (group II) and F6 SkyTaper (group III) instrumentation with the smaller tapered Mtwo files (group I) showed less accumulative propagation of craze lines (p < 0.05) at all time points.

Conclusion

Instruments with greater taper for root canal instrumentation should be used with care to avoid negative long-term effects in the form of propagation of dentinal defects over time. A positive cutting-edge angle and a smaller taper have a positive effect on a lower craze line development.

Clinical relevance

Instruments with a positive cutting-edge angle and a smaller taper are beneficial for the long-term preservation of dentinal tooth structure.

Efficiency of a digital electrofulguration system in contaminated root canals in vitro

Decontamination of the root canal (RC) system is essential for successful endodontic therapy. In this in vitro study, it was evaluated the disinfection potential of an electrofulguration device, the Endox® Endodontic System (EES), in RC infected with Enterococcus faecalis. Sixty-five human lower premolars were instrumented with MTwo® system. The specimens were distributed into six experimental groups (n = 10), according to the irrigation protocol: 2% chlorhexidine gel (CHX); CHX + EES; 5.25% sodium hypochlorite (NaOCl); NaOCl + EES; saline solution (SS); and SS + EES. Five specimens were untreated (control). RC samples were collected before (C1) and after EES treatment (C2), after chemo-mechanical preparation (CMP) (C3), and after final EES treatment (C4). All samples were plated for colony forming units (CFU/mL) onto solid media. The data were analyzed by Wilcoxon and Friedman tests for intragroup comparisons and by Kruskal Wallis test followed by Dunn's test for intergroup comparisons (α = 0.05). Treatment with the EES did not significantly reduce the number of CFU/mL as compared to baseline levels (C1 vs. C2, p> 0.05). After CMP (C3), all groups showed a significantly reduced amount of CFU/mL (p <0.05), with no difference between CHX- and NaOCl-treated samples (p >0.05). Lastly, treatment with the EES following CMP (C4) did not significantly reduce the amount of CFU/mL (C3 vs. C4, p> 0.05). To conclude, the use of the Endox® Endodontic System did not result in considerable bacterial reduction at all operative times, while treatment with NaOCl and CHX was equally efficient for this purpose.

Root canals shaped by nickel-titanium instrumentation with automated computerized numerical control systems

Background

To investigate the efficacy of a nickel-titanium (NiTi) file with an automated computerized numerical control (CNC) system for root canal shaping.

Methods

The movement of the automated device and the insertion angle were investigated. In Experiment 1, simulated resin root canals were randomly divided into four groups (n = 20): manual downward movement using a handpiece (Group 1), vertical downward movement by CNC (Group 2), reciprocating up and down movement by CNC (Group 3), and spiral up and down movement by CNC (Group 4). In Experiment 2, five different insertion angles of the NiTi file were evaluated (n = 20). Four parameters were used to evaluate the shaping ability: change in the working length, central axis offset, curvature variation, and preparation time. Groups were compared using one-way analysis of variance (ANOVA) with significance was set at P < 0.05.

Results

The change in central axis position in the curved part of the root canal was found to be smaller in Group 4 than in other groups (P < 0.05). The curvature changes and preparation time of Groups 1 and 4 were significantly reduced compared with Groups 2 and 3 (P < 0.05). The variation in working length and curvature in the 5° insertion angle group was significantly smaller than in the other groups (P < 0.05).

Conclusions

A spiral up and down movement, controlled by the CNC machine, and 5° insertion angle, maintained original root canal shape more precisely than other methods.

Comparing the amount of removed dentin thickness in root canal treated primary molar teeth using different instrumentation techniques: in-vitro study using CBCT

PURPOSE

There is a clinical dilemma about root canal preparation for endodontic treatment of primary teeth. This study aimed to compare the amount of dentin removal in root canal treated primary molar teeth with three preparation techniques by cone-beam computed tomography (CBCT).

METHODS

A total of 39 s primary molar teeth were selected with a minimum of two-thirds of the entire root length. Access cavity was prepared and preliminary CBCT images were taken and viewed by Romexis programme. The wall thickness of the canal was measured in the danger zone at two axial cut sections of 1 and 2 mm below furcation. Then, the teeth were instrumented with three different methods as manual K-files (size 15-30), Gates glidden burs (in decreasing order of size #2 and #1 followed by hand k-files up to file number 25), and ProTaper rotary files. After canal preparation, the specimens were placed in the same position, and the canal wall thickness was remeasured. Data were analysed by using one-way ANOVA and Kruskal-Wallis tests (α = 0.05).

RESULTS

The amounts of removed dentin thickness was not significantly different among the three groups at two axial cut sections of 1 mm and 2 mm below furcation (P = 0.27 and 0.17, respectively).

CONCLUSION

Within the limitations of this study, the three instrumentation techniques used in primary molars were comparable regarding the amount of dentin removal.

Evaluation of debris and smear layer formation using three different NI-TI rotary instrument systems: An in vitro scanning electron microscope study

Aim:

The aim of the study is to evaluate of debris and smear layer formation after using rotary ProTaper Universal, Twisted File, and XP Endo file systems under scanning electron microscope.

Materials and Methods:

Forty freshly extracted mandibular second premolar teeth were taken to decoronate at the cementoenamel junction to make the remaining root length 15 mm. Specimens were divided into four groups of 10 teeth each, Group I (control) – no instrumentation. Group II – ProTaper Universal rotary file (F2), Group III – twisted file (ISO size 0.25 and 6% taper), Group IV – XP Endo file (ISO size 0.25). During instrumentation, 5 ml normal saline was used as irrigating agent. Grooves parallel to the longitudinal axis of the root were made on the mesial and distal surface of each specimen to split it into two halves and examined under scanning electron microscope at ×1500 and ×5000 magnification. Photomicrographs were taken to evaluate debris and smear layer. Evaluation of photomicrographs was done using a score index.

Results:

One-way analysis of variance (ANOVA) was used to compare more than one means at a time. Tukey's critical difference followed by ANOVA was used to compare the mean values pair wise. P <0.05 was considered to be statistically significant. Among all the file systems, Group II showed maximum amount of debris (3.50 ± 1.109) followed by Group III (2.83 ± 1.238) and least amount was showed by Group IV (2.65 ± 1.122) at all levels (cervical, middle, and apical third). Among all the experimental groups, Group II showed maximum amount of smear layer (2.75 ± 1.149) followed by Group III (2.40 ± 0.982) and least amount of smear layer shown by Group IV (2.10 ± 0.841) at all levels (cervical, middle and apical third), the result was statistically significant (P < 0.05).

Conclusions:

At all the levels (cervical third, middle third, and apical third), among all the experimental groups, highest amount of debris and smear layer was formed by ProTaper Universal rotary file followed by Twisted file and least amount showed by XP Endo file system. In all the levels, control group showed highest amount of debris but least amount of smear layer.

A micro-CT evaluation of the performance of rotary and reciprocating single-file systems in shaping ability of curved root canals

To compare the shaping ability of different single-file systems in the preparation of mesial curved canals of mandibular molars using micro-CT technology. Fifteen mesial roots of mandibular molars with two independent and curved canals (n = 30) were selected, scanned at a resolution of 26.7 μm anatomically matched, and distributed into three groups (n = 10), according to the preparation system: WaveOne 25.08, Reciproc 25.08, and OneShape 25.06. A final micro-CT scanning was performed, data sets were registered with their respective counterparts, and compared regarding the three-dimensional (volume, surface area, and structure model index - SMI) and two-dimensional (perimeter, area, roundness, major and minor diameters) parameters, as well as, canal transportation, using ANOVA and post hoc Tukey tests (α = 5%). Overall, no difference was observed between groups regarding area, perimeter, volume, surface area, and canal transportation (p > 0.05). Within group, no canal transportation was significantly higherobserved in the apical third (0.10 ± 0.05 mm) compared to coronal (0.08±0.040 mm) and middle (0.07 ± 0.03 mm) thirds (p < 0.05). Structure model index (SMI) was statistically higher after preparation with OneShape instrument (0.36 ± 0.26) compared to other systems (p < 0.05). Within the parameters of this study, similar shaping ability was observed in the preparation of mesial curved root canals of mandibular molars with Reciproc, OneShape and WaveOne systems.

Residual smear layer after root canal instrumentation by using Niti, M-Wire and CM-Wire instruments: A scanning electron microscopy analysis

Objective:

The purpose of this study was to compare the amount of residual smear layer after root canal instrumentation by using Ni-Ti, M-Wire, and CM-Wire instruments.

Materials and Methods:

Seventy-two mandibular incisors were randomly divided into six groups according to the system used: WaveOne (WO), Reciproc (RP), Unicone (UC), ProTaper Next (PN), Mtwo (MT), and HyFlex (HF). Afterward, the specimens were cleaved in the mesiodistal and buccolingual direction for analysis by scanning electron microscopy.

Results:

Considering both directions and root canal thirds, there was no difference between HF, MT, and PN. RP, UC, and WO presented a significant difference between the directions, and the cervical third showed a significantly smaller quantity of residual smear layer compared with the apical third. When the systems were compared among them, there was a significant difference only between RP and WO.

Conclusions:

Residual smear layer observed after instrumentation with the different systems was similar, except for quantities between the reciprocating systems.

The influence of kinematics of engine-driven nickel-titanium instruments on root canal shape assessed by micro-computed tomography: a systematic review

AIM

To evaluate if the kinematics of engine-driven instruments affect the root canal shape.

METHOD

The systematic review was registered in PROSPERO (CRD 42017077043). A broad search was performed for articles published before 26 September 2018 in the electronic databases: pubmed, scopus, web of science and Lilacs using MeSH and free terms. Only in vitro studies with human teeth that evaluated root canal shape by volume, surface area and unprepared surface area using reciprocating and rotary system assessed by micro-computed tomography were included. A modified checklist for randomized controlled trials from the Joanna Briggs Institute was used to assess the risk of bias.

RESULTS

Twenty-one articles were selected. According to quality assessment, all studies were considered 'moderate methodological quality'. Eighteen articles analysed volume increase, only four studies showed statistically significant difference, three indicating that the reciprocating movement obtained a greater increase in volume than the rotary system and one rotary system obtained a greater increase. Twelve studies analysed surface area, only three studies showed statistically significant difference, two presented a reciprocating system revealing greater amount of surface area and one showed a rotary system obtained a greater amount of surface area. Ten articles evaluated unprepared surface area, two studies that analysed total length, one study presented that the rotary system revealed lower unprepared surface area while another study showed reciprocating with less unprepared area. One study analysed middle and apical third, and observed that the rotary system presented lower unprepared surface area in the middle third.

CONCLUSIONS

Both the rotary and reciprocating kinematics produce changes in volume and surface area and leave unprepared areas in the root canal, however reciprocating system showed greater increase of volume and surface area, while the rotary system maintains less unprepared surface area.

Comparative evaluation of instrumentation timing and cleaning efficacy in extracted primary molars using manual and NiTi rotary technique - Invitro study

Aim

To compare the timing of instrumentation and cleaning efficacy between manual K files and NiTi rotary files in extracted primary molars.

Study design

in-vitro study was conducted in 90 root canals of extracted primary molars which were subdivided in three groups viz. Control (No instrumentation), Manual (K files), Rotary (ProFiles) with 30 canals in each group. Mesiobuccal (MB) and Mesiolingual (ML) canals of mandibular molars, and MB and Distobuccal (DB) canals of maxillary molars were included in the test group whereas Distal canals in mandibular molars and Palatal canals in maxillary molars were included in the control group.

Method

Teeth were mounted and canals were injected with India ink to stain the canal walls. Canal preparation was done as per the group. After instrumentation, teeth were demounted, decalcified and cleared to make them transparent for scoring according to the extent of removal of India ink. Timing of instrumentation and cleaning efficacy of canals in coronal, middle and apical thirds were assessed in each sample.

Results

Mean timing of instrumentation in rotary group was 3.54 ± 1.14 min and 4.32 ± 1.04 min in manual group. Mean cleaning efficacy scores in manual and rotary groups were 2.03 and 1.66 in coronal third, 1.08 and 1.18 in middle third and 0.67 and 1.08 in apical third respectively. Inter-group comparisons showed no statistically significant difference in cleaning efficacy among test groups in all thirds of root canals.

Conclusion

NiTi rotary technique has comparable cleaning efficacy, with significantly less timing of instrumentation compared to manual K-files.

Comparative Evaluation of Cleaning Efficacy using Four Novel Nickel-titanium Rotary Instruments: An in vitro Scanning Electron Microscope Study

AIM

The aim of the study was to compare the cleaning efficacy (debris and smear layer removal) of two multifile rotary systems (MTwo and Silk) and two single-file rotary systems (F6 Skytaper and NeoNiTi).

MATERIALS AND METHODS

Eighty mesial canals of mandibular first molars were cleaned and shaped using four nickel-titanium (NiTi) rotary instruments to size # 25 and 3% NaOCl and 17% ethylenediaminetetraacetic acid (EDTA). Samples were randomly divided into four equal groups (n = 20) according to instrumentation: Group I, Mtwo; group II, Silk; group III, F6 Skytaper; group IV, NeoNiTi. Samples were split longitudinally and examined under scanning electron microscope (SEM) for debris and smear layer removal in coronal, middle, and apical thirds of each root canal.

RESULTS

F6 skytaper and Mtwo groups showed significantly higher debris removal than Silk and NeoNiTi groups in apical third of root canal as well as when compared with NeoNiTi group in middle third. F6 Skytaper group showed significantly higher debris and smear layer removal than Silk group in coronal third. There was statistically significant difference among all thirds of root canal in terms of debris removal in Silk and NeoNiTi groups. There was statistically significant difference among all thirds of root canal in F6 Skytaper and NeoNiTi groups in terms of smear layer removal.

CONCLUSION

F6 Skytaper single-file rotary instrumentation showed the maximum cleaning efficacy followed by Mtwo multifile rotary instrumentation in all thirds of root canal.

CLINICAL SIGNIFICANCE

F6 Skytaper rotary instrument is most efficient followed by Mtwo rotary instrument among all rotary instruments.

Analysis of Surface Characteristics of ProTaper Universal and ProTaper Next Instruments by Scanning Electron Microscopy

Background

Many new rotary files systems have been introduced, however, limited research has been conducted related to the surface irregularities of these files and if these have any effects on the files themselves. Hence, the aim of the present study was to analyze surface irregularities of the ProTaper® Universal rotary files (PTU) and the ProTaper Next™ rotary files (PTN) before and after instrumentation in curved canals. The main objective was to investigate the nature of these irregularities and how they might influence the use and fracture of rotary files during root-canal treatments.

Material and Methods

The files were examined pre-operatively using a stereomicroscope and scanning electron microscopy(SEM) to analyze surface imperfections and the presence of particles. Mesial roots of forty extracted mandibular molars were selected. Each instrument was used to prepare one of the mesial canals. The files were then rinsed with alcohol, and autoclaved and analyzed again.

Results

Of the 80 files used in this study, five files fractured, five files unwound and seven files were curved or bent and they all belonged to the PTU group. Irregularities and debris could be visualized with the SEM on both unused PTU and PTN files. Most of the debris was found associated with deeper milling grooves and defects on the surface of the metal. Surface analysis of the files that were used and sterilized were performed and the SEM images demonstrated organic debris, metal flash, and crack formation and initiation of fractures for both file types. All files showed machining grooves, metal flash, debris, and defects on cutting edges.

Conclusions

These irregularities appear to be critical in the accumulation of debris and initiation of fatigue and crack propagation within the NiTi alloy. The accumulation of debris could be a concern due to the potential exchange of organic debris between patients.

Key words:ProTaper® Universal, ProTaper Next™, surface characteristics, SEM.

An in vitro study on the efficacy of removing calcium hydroxide from curved root canal systems in root canal therapy

To compare the efficacy of various irrigants (citric acid, ethylenediaminetetraacetic acid (EDTA) and NaOCl) and techniques in removing Ca(OH)₂ in two types of curved root canal systems, simulated root canals with specific curvatures were used to investigate the effects of different irrigants and instruments on Ca(OH)₂ removal. The optimal methods were verified on extracted human teeth. Simulated root canals were assigned to one of two groups based on the irrigation solution: 10% citric acid or 2.5% NaOCl. Each group was divided into four subgroups according to the technique used to remove Ca(OH)₂. The percentage of Ca(OH)₂ removal in different sections of root canals was calculated. On the basis of the results obtained for the simulated canals, 10% citric acid and 17% EDTA were applied to remove Ca(OH)₂ from the extracted human teeth with curved root canal systems. The teeth were scanned by micro computed tomography to calculate the percentage of Ca(OH)₂ removal in the canals. In simulated root canals, we found that 10% citric acid removed more Ca(OH)₂ than 2.5% NaOCl in the 0–1 mm group from the apex level (P<0.05). Ultrasonic and EndoActivator activation significantly removed more Ca(OH)₂ than a size 30 K file in the apical third (P<0.05). However, there were no significant differences in any sections of the canals for 10% citric acid or 17% EDTA in removing Ca(OH)₂ in extracted human teeth. We concluded that it was effective to remove residual Ca(OH)₂ using the decalcifying solution with EndoActivator or Passive Ultrasonic Irrigation in a curved root canal system. A protocol for Ca(OH)₂ removal was provided based on the conclusions of this study and the methods recommended in previous studies.

Cleaning Effectiveness of a Reciprocating Single-file and a Conventional Rotary Instrumentation System

Objective:

To compare cleaning effectiveness by histological analysis of a reciprocating single-file system with ProTaper rotary instruments during the preparation of curved root canals in extracted teeth.

Methods:

A total of 40 root canals with curvatures ranging between 20 - 40 degrees were divided into two groups of 20 canals. Canals were prepared to the following apical sizes: Reciproc size 25 (n=20); ProTaper: F2 (n=20). The normal distribution of data was tested by the Kolmogorov-Smirnov test and the values obtained for the test (Mann-Whitney U test, P < .05) were statistically analyzed using the GraphPad InStat for the Mac OS software (GraphPad Software, La Jolla, CA, USA).

Results:

There were no significant differences in remaining debris (P > .05) between the two groups.

Conclusion:

The application of reciprocating motion during instrumentation did not result in increased debris when compared with continuous rotation motion, even in the apical part of curved canals. Both instruments resulted in debris in the canal lumen, irrespective of the movement kinematics applied.

Canal cleanliness using different irrigation activation systems: a SEM evaluation

OBJECTIVES

The purpose of this study was to assess the efficacy of different final irrigation activation methods in removing debris and smear layer in the apical, middle, and coronal portion of straight root canals.

MATERIAL AND METHODS

Straight root canals of 58 freshly extracted mandibular premolars were used. Root canals were prepared to size 40.06. Irrigation was performed using 3% sodium hypochlorite. Samples were divided into four equal groups (n = 12) according to the irrigation activation techniques: (A) manual irrigation (MI), (B) EndoActivator (EA) (Dentsply Maillefer, Ballaigues, Switzerland), (C) sonic activation EDDY (EDDY; VDW, Munich, Germany), and (D) passive ultrasonic irrigation (PUI). Ten teeth served as negative controls. Roots were split longitudinally, and the canal walls were subjected to scanning electron microscopy. The presence of debris and smear layer at coronal, middle, and apical levels were evaluated using a 5-point scoring system and statistically analyzed using Kruskal-Wallis and chi-square tests.

RESULTS

Canal cleanliness decreased from coronal to apical (P = 0.035). Significantly more debris was removed with EA, EDDY, and PUI compared to MI (P < 0.001; total values), but no differences were observed in the different portions of the root canals (P > 0.05). Smear layer removal with PUI, EA, and EDDY was not significantly different (P > 0.05), but only EDDY and PUI were superior to MI (P < 0.01).

CONCLUSION

All activation methods created nearly debris-free canal walls and were superior compared to manual irrigation (P < 0.001). EDDY and PUI also showed significantly better smear layer scores compared to manual irrigation.

CLINICAL RELEVANCE

The sonic activation system EDDY performed equally as well as PUI, and both methods were significantly superior compared with manual irrigation in straight root canals with regard to debris and smear layer removal.

Evaluation of the incidence of microcracks caused by Mtwo and ProTaper Next rotary file systems versus the self-adjusting file: A scanning electron microscopic study

Introduction:

To evaluate the incidence of microcrack formation canal preparation with two rotary nickel–titanium systems Mtwo and ProTaper Next along with the self-adjusting file system.

Materials and Methods:

One hundred and twenty mandibular premolar teeth were selected. Standardized access cavities were prepared and the canals were manually prepared up to size 20 after coronal preflaring. The teeth were divided into three experimental groups and one control group (n = 30). Group 1: The canals were prepared using Mtwo rotary files. Group 2: The canals were prepared with ProTaper Next files. Group 3: The canals were prepared with self-adjusting files. Group 4: The canals were unprepared and used as a control. The roots were sectioned horizontally 3, 6, and 9 mm from the apex and examined under a scanning electron microscope to check for the presence of microcracks. The Pearson's Chi-square test was applied.

Results:

The highest incidence of microcracks were associated with the ProTaper Next group, 80% (P = 0.00), followed by the Mtwo group, 70% (P = 0.000), and the least number of microcracks was noted in the self-adjusting file group, 10% (P = 0.068). No significant difference was found between the ProTaper Next and Mtwo groups (P = 0.368) while a significant difference was observed between the ProTaper Next and self-adjusting file groups (P = 0.000) as well as the Mtwo and self-adjusting file groups (P = 0.000).

Conclusion:

All nickel–titanium rotary instrument systems were associated with microcracks. However, the self-adjusting file system had significantly fewer microcracks when compared with the Mtwo and ProTaper Next.

Centering Ability of ProTaper Next and WaveOne Classic in J-Shape Simulated Root Canals

Introduction. The aim of this study was to evaluate and compare the shaping and centering ability of ProTaper Next (PTN; Dentsply Maillefer, Ballaigues, Switzerland) and WaveOne Classic systems (Dentsply Maillefer) in simulated root canals. Methods. Forty J-shaped canals in resin blocks were assigned to two groups (n = 20 for each group). Photographic method was used to record pre- and postinstrumentation images. After superimposition, centering and shaping ability were recorded at 9 different levels from the apex using the software Autocad 2013 (Autodesk Inc., San Rafael, USA). Results. Shaping procedures with ProTaper Next resulted in a lower amount of resin removed at each reference point level. In addition, the pattern of centering ability improved after the use of ProTaper Next in 8 of 9 measurement points. Conclusions. Within the limitations of this study, shaping procedures with ProTaper Next instruments demonstrated a lower amount of resin removed and a better centering ability than WaveOne Classic system.

Comparative analysis of cleaning ability of three nickel-titanium rotary systems: ProTaper universal, K3 and Mtwo: An in vitro scanning electron microscopic study

BACKGROUND

Endodontic instruments including the nickel-titanium (NiTi) instruments produce debris and smear layer during instrumentation. The study was carried out to evaluate and compare the cleaning effectiveness of root canal preparation using three different rotary NiTi instrumentation systems - ProTaper Universal, K3 and Mtwo by means of scanning electron microscopy (SEM).

METHODS

Thirty-six freshly extracted permanent mandibular molars were randomly divided into four groups: ProTaper Universal, K3, Mtwo system and control group. The mesiobuccal canal was cleaned and shaped with rotary instruments. The intracanal irrigant used after each instrument was 3 mL of 3% sodium hypochlorite (NaOCl). After the cleaning and shaping was completed, a 1-min 17% ethylenediaminetetraacetic acid rinse was followed by a final NaOCl rinse. All samples were decoronated. Mesial roots were sectioned buccolingually and examined under SEM at 500× magnification in three areas of root canal. Canal walls were quantitatively evaluated using a five-score evaluation scale. Statistical analysis was done using Kruskal-Wallis test, Fisher's exact test and weighted kappa.

RESULTS

Completely clean canals were not found in any of the groups. The mean value of debris score for ProTaper, K3 and Mtwo was 2.35, 2.41 and 2.22 respectively. There was no statistically significant difference between the three tested groups (P = 0.237). The apical thirds of the canal was found to be significantly less clean than coronal and middle thirds irrespective of the system used.

CONCLUSIONS

There was no statistically significant difference between the three tested groups - ProTaper, K3 and Mtwo in cleaning different regions of the canal - coronal, middle and apical.

Evaluation of apically extruded debris during root canal preparation in primary molar teeth using three different rotary systems and hand files

AIM

To assess the amount of debris extruded apically during root canal preparation using various nickel titanium instrumentation systems and hand files in primary molar teeth.

DESIGN

Sixty extracted primary first mandibular molar human teeth were randomly assigned to four groups (n = 15 teeth for each group). The canals were then instrumented with the following instrument systems: Revo-S, Mtwo, ProTaper Next, and hand files. Apically extruded debris during instrumentation was collected into pre-weighed Eppendorf tubes. The Eppendorf tubes were then stored in an incubator at 70°C for 5 days. The weight of the dry extruded debris was established by subtracting the pre-instrumentation and post-instrumentation weight of the Eppendorf tubes for each group. The data were analyzed using one-way analysis of variance (anova) and Tukey's post hoc tests.

RESULTS

ProTaper Next files were associated with less apically extruded debris than the Mtwo, Revo-S, and hand files (P < 0.05). Hand files extruded more debris than Mtwo and Revo-S instruments (P < 0.05), but there was no significant difference found between the Mtwo and Revo-S instruments (P > 0.05).

CONCLUSIONS

All instruments were associated with apical extrusion of debris. ProTaper Next files caused less debris extrusion compared to the other systems used.

'Volumetric analysis of hand and rotary root canal instrumentation and filling in primary teeth using Spiral Computed Tomography' - an invitro study

AIM

To compare and evaluate the volumetric analysis of pre- and post-root canal instrumentation in primary teeth using hand and rotary files and also to analyse the volume of root canal filling.

MATERIALS AND METHODS

A total of 20 primary teeth were divided into two groups randomly and subjected to spiral computed tomography (SCT) analysis before and after instrumentation. For manual technique (Group 1), teeth were prepared using K files and rotary (Group 2) preparation was performed with Mtwo files. Volumetric enlargement was calculated using Osirix software. Root canals were then filled with rotary lentulospiral using zinc oxide-eugenol cement (ZOE). The filled volume in each canal was measured using SCT and the percentage of obturated volume was calculated. The data were statistically analysed using paired t-tests.

RESULTS

There was a statistically significant difference in the volume of root canal enlarged in both the groups. Rotary files showed significant increase in the volume compared to K files. Mtwo instrumented root canals showed good obturated volume compared to manual technique, although voids were common in both the groups.

CONCLUSION

Rotary root canal instrumentation may be indicated for utilization in primary teeth, for enhancing root canal preparation and good quality of root canal filling.

Performance of Three Single Instrument Systems in the Preparation of Long Oval Canals

Abstract This study aimed to evaluate the performance of the Wave One, Easy ProDesign Logic and One Shape systems in the preparation of long oval root canals. Forty-two mandibular incisors were randomized into three groups: Group I, Wave One Primary (WO) (#25.08); Group II, Easy ProDesign Logic (EPL) (#25.06) and Group III, One Shape (OS) (#25.06). Micro-computed tomography scans were obtained pre- and post-preparation of the samples. Instrument fractures or loss of working length did not occur in any of the groups. There was a statistically significant difference in total root canal volume between the WO and EPL (p<0.05) and OS systems (p<0.05) The mean percentages of instrumented canal area in the middle thirds were 76.9% in the WO, 62.3% in the EPL and 71.8% in the OS (p>0.05). The OS system had the strongest correlation between volume increase and instrumented area (R=0.63). The WO, EPL and OS systems presented mean preparation times of 2.13 min, 0.54 min, and 2.21 min (p<0.05), respectively. All three systems enabled the safe preparation of long oval root canals. The WO system most effectively increased root canal volume, but it did not affect the instrumented areas. The OS system had the strongest correlation between volume increase and instrumented area, while the EPL system was the fastest.

Rotary endodontics in primary teeth - A review

Endodontic treatment in primary teeth can be challenging and time consuming, especially during canal preparation, which is considered one of the most important steps in root canal therapy. The conventional instrumentation technique for primary teeth remains the "gold-standard" over hand instrumentation, which makes procedures much more time consuming and adversely affects both clinicians and patients. Recently nickel-titanium (Ni-Ti) rotary files have been developed for use in pediatric endodontics. Using rotary instruments for primary tooth pulpectomies is cost effective and results in fills that are consistently uniform and predictable. This article reviews the use of nickel-titanium rotary files as root canal instrumentation in primary teeth. The pulpectomy technique is described here according to different authors and the advantages and disadvantages of using rotary files are discussed.

Comparative evaluation of the shaping ability of two different nickel-titanium rotary files in curved root canals of extracted human molar teeth

AIM

The aim of the present study was to compare the shaping ability of two different nickel-titanium rotary files in the curved root canals of extracted human molar teeth.

METHODS

Thirty root canals of 17 extracted human molars teeth were randomly assigned to two experimental groups (n = 15): ProTaper Next and ProTaper Universal (PTU), on the basis of the rotary files system used. The final size of all apical foramina was 0.25 mm in diameter. Standardized digital radiographs were taken before and after instrumentation in both clinical and proximal views, with a size 10 K-file inserted into the canal for the determination of the angle of curvature and apical transportation. Preparation time and fractured or deformed instruments were also recorded. The unpaired Student's t-test was used to compare results.

RESULTS

There was no significant difference between the two instruments with respect to canal straightening and apical transportation before and after instrumentation (P > 0.05). The use of both instruments resulted in a significant reduction in the angle of curvature after instrumentation (P < 0.05). Instrumentation time was significantly greater for PTU (P < 0.05).

CONCLUSIONS

The ProTaper Universal and ProTaper Next systems performed similarly with regard to the straightening of curved root canals and apical transportation. ProTaper Next was significantly faster than ProTaper Universal.

Reduction of Enterococcus faecalis in curved root canals after various sizes and tapers of canal preparation

Aims:

The aim of this study was to evaluate the reduction of Enterococcus faecalis in curved root canals after various sizes and tapers of the canal preparation.

Materials and Methods:

Mandibular first molars (n = 103) with curved mesiobuccal canals were divided into one control (n = 5) and 7 experimental (n = 14) groups, were inoculated with E. faecalis (ATTC 29212) and prepared with the following RaCe files (FKG Dentaire) as master apical file: Groups: 25.04, 25.06, 30.04, 30.06, 35.04, 35.06 and 40.06. All the experimental groups were irrigated with 2 mL of 1% sodium hypochlorite during instrumentation and finally rinsed with 17% ethylenediaminetetraacetic acid (EDTA) (2 mL) followed by 5.25% NaOCl (2 mL) and sterile distilled water. Colony counting was performed after incubation.

Statistical Analysis Used:

Resulting data were analyzed using one-way ANOVA and Tukey's post-hoc test, (P < 0.05).

Results and Conclusions:

All the experimental groups showed significant bacterial reduction (P < 0.001). Although the greater the size/taper or both led to more decreased amount of bacteria, differences between the groups with the identical size and different tapers, and among the groups with the same taper and different sizes were not significant. Based on this study, 25.04 along with using 2 mL of 1% NaOCl during instrumentation, and using 17% EDTA and 5.25% NaOCl as final rinse successively after the termination of preparation, can effectively reduce intra-canal bacteria and preserve root structure.

Intra-canal calcium hydroxide removal by two rotary systems: A comparative study

Aim:

The presence of calcium hydroxide (Ca(OH)₂) in the root canal interferes with the apical root canal sealing and may result in periapical lesions in the long run. The present study was aimed to compare the efficacy of two rotary systems of Race and Mtwo in the removal of Ca (OH)₂ aqueous-based from distobuccal canals of human maxillary molars.

Materials and Methods:

A total of 44 distobuccal root canals of human maxillary molars were randomly distributed into two groups of 20 canals each and two control groups. Specimens in each group were instrumented with similar master apical rotary (MAR) and flexible files according to the manufacture's guidelines. The Ca (OH)₂ paste was placed in canals using # 20 lentulo and radiographs were taken from the two dimensions. The roots were incubated for 1 week at 37°C and 100% humidity and Ca (OH)₂ was removed from canals by MAR, afterward. Then, the roots were longitudinally split in halves by diamond disk and chisel without entering the root canals. Photos were taken from the canals’ walls by a stereomicroscope with × 10 magnification. Next, according to a defined scoring system, photos were scored by four endodontists, so that scores 1 and 2 (nonvisible remnants or scattered remnants of Ca(OH)₂) were considered as acceptable and scores 3 and 4 (distinct mass or densely-packed mass of Ca(OH)₂) were regarded as nonacceptable.

Results:

The obtained findings indicated that in coronal, middle, and apical portions of the root canal, 45, 60, and 65% of Mtwo specimens and 40, 50, and 55% of specimens prepared by the Race system acquired an acceptable score (1 and 2), respectively. Moreover, the results showed no significant difference between the two groups (P > 0.05).

Conclusions:

Both Mtwo and Race rotary systems with acceptable removal efficiency (score 1 and 2) were similarly able to remove Ca(OH)₂

Assessment of root canal enlargement using Mtwo and BioRace rotary files

Objective. To evaluate root canal enlargement following mechanical shaping using 2 nickel titanium rotary systems. Material and Methods. Forty single-rooted teeth were immersed in resin and sectioned perpendicular to the long axis at 4, 8, and 12 mm from the apex. Digital capture of sections was performed before and after canal instrumentation using Mtwo and BioRace instruments. The area increase of endodontic space was calculated by subtraction. Results. The use of both instruments has allowed the removal of great amounts of dentin from the canal walls, even when the endodontic morphology is characterized by awkwardness to reach recesses. Conclusions. Both procedures seem to be valid and no differences were found between Mtwo and BioRaCe considering the amount of dentin removed at different distances from the apex.

Modifications in Canal Anatomy of Curved Canals of Mandibular First Molars by two Glide Path Instruments using CBCT

BACKGROUND

The creation of glide path reduces the risk of instrument breakage. Glide path is created before using NiTi rotary instrumentation Aim: This study compared the changes in the root canal anatomy after creation of glide path using Path Files (PF) and V Glide Path 2 (VGP2) using Cone Beam Computed Tomography (CBCT).

MATERIALS AND METHODS

Hundred extracted mandibular first molars with curved mesial roots, curvature angles ranging within 20-30 degrees were assigned into two groups (n = 50 each). Glide path was prepared using PF (Group I) and VGP2 (Group II). CBCT images were obtained before and after instrumentation. The technical outcomes were compared at 0, 1, 2, 3, 5 and 7mm intervals. The data was analyzed using t-test and Chi-square test.

RESULT

There was a statistical difference between the root canal curvatures and working time between the two groups (p < 0.05). Canals transported towards the distal side in Group II but there was a slight mesial transportation in Group I at 0mm. Group I exhibited a better centric ability except at 1mm interval (p > 0.05). The changes in the volume were statistically significant only at 2mm interval (p < 0.05). The difference in the cross sectional area was not statistically significant at any interval (p > 0.05).

CONCLUSION

Within the limits of this study the rotary Nickel Titanium Path Files appeared to be suitable instruments for safe and easy creation of glide path.

Comparison of Hero 642 and K3 rotary nickel-titanium files in curved canals of molars and a systematic review of the literature

The aim of the present study was to compare the root canal preparation ability of rotary nickel-titanium (NiTi) Hero 642 and K3 files in curved mandibular or maxillary molars. A total of 40 extracted mandibular molars with two separate mesial canals, an apical width of approximately size ≤15 and a root canal curvature of 15–30° were randomly divided into two groups and instrumented using Hero 642 (n=20) or K3 files (n=20). Canal straightening, working length, transportation, cross-sectional area, minimum dentin thickness and the canal angle curvature degree were examined, and a systematic review of the literature was conducted. No statistically significant differences were observed between the two groups with regard to the mean degree of straightening, mean change in working length, mean transportation, amount of dentin removed or remaining minimum dentin thickness (P>0.05). The canal angle curvature decreased in the two groups postoperatively. The systematic review identified six studies, and overall the two files performed similarly in the majority of categories examined. Therefore, the rotary NiTi Hero 642 and K3 files demonstrated comparable shaping abilities and maintenance of working length.

Comparative analysis of canal transportation and centring ability of three Ni-Ti rotary endodontic systems: Protaper®, MTwo® and Revo-S™, assessed by micro-computed tomography

The aim of this study was to use high-resolution micro-CT to evaluate the effects of three Ni-Ti rotary endodontic instruments, Mtwo® (VDW, München, Germany), ProTaper® (Dentsply-Maillefer, Ballaigues, Switzerland) and Revo-S™ (MicroMega, Besançon, France), on canal transportation and centring ratio. Fifty-four mesial roots of extracted mandibular molars with an angle of curvature of 25-35° were randomly divided into three groups of eighteen. Each group was instrumented with a previously unused Ni-Ti rotary system. The final instruments used were #30/0.05 taper (Mtwo®), F3 #30/0.09 apical taper (ProTaper®) and AS30 #30/0.06 taper (Revo-S™). Teeth were scanned before and after instrumentation using micro-computed tomography with a spatial resolution of 20 μm to measure volume and shaping changes. All images were filtered to improve signal-to-noise ratio. To determine the perimeter of roots and canals exactly, images were segmented in each slice with an edge detection process. Canal transportation and centring ratio were evaluated at 1, 3, 5 and 7 mm from the end of each root. The method developed by Gambill et al. was chosen. ANOVA was conducted with the significance threshold set at p < 0.05. No statistically significant differences were found among the three groups in terms of canal transportation or centring ratio at any level. These systems give similar results with regard to the tested shaping parameters. Under the tested conditions and within the limitations of this study, these systems were able to produce centred preparations of curved canals with minimal transportation.

A new device to test cutting efficiency of mechanical endodontic instruments

BACKGROUND

The purpose of the present study was to introduce a new device specifically designed to evaluate the cutting efficiency of mechanically driven endodontic instruments.

MATERIAL AND METHODS

Twenty new Reciproc R25 (VDW, Munich, Germany) files were used to be investigated in the new device developed to test the cutting ability of endodontic instruments. The device consists of a main frame to which a mobile plastic support for the hand-piece is connected and a stainless-steel block containing a Plexiglas block against which the cutting efficiency of the instruments was tested. The length of the block cut in 1 minute was measured in a computerized program with a precision of 0.1mm. The instruments were activated by using a torque-controlled motor (Silver Reciproc; VDW, Munich, Germany) in a reciprocating movement by the "Reciproc ALL" program (Group 1) and in counter-clockwise rotation at 300 rpm (Group 2). Mean and standard deviations of each group were calculated and data were statistically analyzed with a one-way ANOVA test (P<0.05).

RESULTS

Reciproc in reciprocation (Group 1) mean cut in the Plexiglas block was 8.6 mm (SD=0.6 mm), while Reciproc in rotation mean cut was 8.9 mm (SD=0.7 mm). There was no statistically significant difference between the 2 groups investigated (P>0.05).

CONCLUSIONS

The cutting testing device evaluated in the present study was reliable and easy to use and may be effectively used to test cutting efficiency of both rotary and reciprocating mechanical endodontic instruments.