A laboratory analysis of gutta-percha-filled area obtained using Thermafil, System B and lateral condensation

ProTaper universal retreatment retreatment potential in oval-shaped canals filled with different obturation techniques-A micro-computed tomography study

Aim

The objective of this in vitro micro-computed tomography investigation is to assess the efficacy of the ProTaper Universal Retreatment System in retreating oval-shaped root canals filled with three obturation procedures.

Materials and Methods

Thirty-six lower incisors with a single oval root canal were prepared using XP-Endo Shaper up to size 30/0.04, and allocated into three equal groups based on the filling technique: Group 1: Warm vertical condensation technique; Group 2: GuttaCore obturators; Group 3: Cold lateral condensation technique. All samples were further retreated using the ProTaper Universal Retreatment system. Micro-CT analysis was performed before and after the retreatment procedure. Statistical analysis was performed with a significance level of 0.05. Data analysis was conducted using the Kolmogorov-Smirnov and Kruskal-Wallis H tests.

Results

The best performance of the files was achieved when the removal of the filling in the entire canal was considered. However, this outcome was not statistically significant when compared with the other observed root canal levels. The retreatment procedure could not ensure thorough cleanliness of the canal walls from filling remnants, regardless of the obturation technique and observational level.

Conclusions

The ProTaper Universal Retreatment system used for the removal of gutta-percha and sealer in oval-shaped root canals demonstrated equal effectiveness, regardless of the obturation technique used.

Single Cone Obturation versus Cold Lateral Compaction Techniques with Bioceramic and Resin Sealers: Quality of Obturation and Push-Out Bond Strength

Objectives

This study compared the obturation quality and push-out bond strength of single cone obturation (SCO) and cold lateral compaction (CLC) with AH-Plus and Sure Seal Root (SSR).

Materials and Methods

This in vitro experimental study was conducted on 88 single-rootedsingle-canal teeth with straight roots that were randomly divided into four groups (n = 22). All teeth were decoronated and underwent cleaning and shaping. Obturation was performed with AH-Plus and SCO technique in group 1 (SAH), AH-Plus and CLC technique in group 2 (LAH), SSR and SCO technique in group 3 (SS), and SSR and CLC technique in group 4 (LS). The roots were then sectioned into 3-mm thick slices and underwent digital photography at x25 magnification to assess the quality of obturation in the coronal, middle, and apical thirds by Image J software. The PBS was measured by a universal testing machine. The mode of failure was also determined under a stereomicroscope.

Results

The PBS was significantly higher in the LSS group than LAH and SAH groups, and also in the SSS group than the SAH group in all sections. The PBS in the LSS group was significantly higher than SSS in the coronal and middle thirds. Voids were significantly lower in LAH than in the SAH group in all sections. In LSS, voids in the coronal third were significantly lower than in LAH. In the middle third, voids in SSS were significantly lower than in SAH. The groups had no significant difference in the mode of failure (P > 0.05). The mean percentage of gutta-percha in the use of AH-Plus sealer was significantly higher than SSR (P < 0.05). The mean percentage of gutta-percha in the coronal third was lower than that in the middle and apical thirds (P < 0.05).

Conclusion

SSR showed higher PBS and less voids than AH-Plus. High PBS of the CLC/SSR group showed that CLC should still be preferred to SCO, and in the case of using SCO, SSR should be preferred to AH-Plus.

A critical analysis of research methods and experimental models to study root canal fillings

Canal filling materials and techniques have been one of the most studied topics in Endodontics. A simple search using the mesh term "root canal filling" in PubMed revealed more than 11,000 articles, an impressive number that is much higher than "root canal disinfection" (5,544 articles) or even the popular "root canal preparation" (8,527 articles). The overriding importance attributed to root filling procedures is not merely intuitive. It derived from the appealing relevance given by the appearance of the white lines in common radiographs grounded on retrospective clinical data that had identified the quality of a root filling as one of the major causes of treatment failure (lack of healing). Since the publication of the Washington study, impressive efforts have been made for the release of new materials and techniques, as well as, for the development of a plethora of laboratory methods to assess the quality of root filling procedures. This narrative review aims to address and discuss the most relevant laboratory methods to assess the root canal filling. Since filling quality improvements have not translated into higher success rates, as reported in longitudinal clinical studies, more than to deliver a simple methodology-based review, this paper aims to present an in-depth critical view on the assessment of laboratory methods used to study the filling materials and techniques. Recent data indicate that the long-term dimensional stability/degradation over time of endodontic sealers plays a central role in the treatment outcome. In this context, laboratory methods should be developed focusing on predicting, at least to some degree, the long-term clinical behaviour of root canal fillings, rather than simply ranking different materials or techniques.

Is Gutta-Percha Still the “Gold Standard” among Filling Materials in Endodontic Treatment?

The paper is an extensive monographic review of the literature, and also uses the results of the authors’ own experimental research illustrating the noticed developmental tendencies of the filling material based on gutta-percha. The whole body of literature proves the correctness of the research thesis that this material is the best currently that can be used in endodontics. Caries is one of the most common global infectious diseases. Since the dawn of humankind, the consequence of the disease has been the loss of dentition over time through dental extractions. Both tooth caries and tooth loss cause numerous complications and systemic diseases, which have a serious impact on insurance systems and on the well-being, quality, and length of human life. Endodontic treatment, which has been developing since 1836, is an alternative to tooth extraction. Based on an extensive literature review, the methodology of qualifying patients for endodontic treatment was analyzed. The importance of selecting filling material and techniques for the development and obturation of the root canal during endodontic treatment was described. Particular attention was paid to the materials science aspects and the sequence of phase transformations and precipitation processes, as well as the need to ensure the stoichiometric chemical composition of Ni–Ti alloys, and the vacuum metallurgical processes and material processing technologies for the effects of shape memory and superelasticity, which determine the suitability of tools made of this alloy for endodontic purposes. The phenomena accompanying the sterilization of such tools, limiting the relatively small number of times of their use, play an important role. The methods of root canal preparation and obturation methods through cold side condensation and thermoplastic methods, including the most modern of them, the thermo-hydraulic condensation (THC) technique, were analyzed. An important element of the research hypothesis was to prove the assumption that to optimize the technology of development and obturation of root canals, tests of filling effectiveness are identified by the density and size of the gaps between the root canal wall, and the filling methods used and devices appropriate for material research, using mainly microscopy such as light stereoscopic (LSM) and scanning electron (SEM). The most beneficial preparations were obtained by making a longitudinal breakthrough of 48 natural human teeth, extracted for medical reasons, different from caries, with compliance with all ethical principles in this field. The teeth were prepared using various methods and filled with multiple obturation techniques, using a virtual selection of experimental variants. The breakthroughs were made in liquid nitrogen after a one-sided incision with a narrow gap created by a diamond disc using a materialographic cutter. The best effectiveness of the root canal filling was ensured by the technology of preparing the root canals with K3 rotary nitinol tools and filling the teeth with the THC thermoplastic method using the System B and Obtura III devices with studs and pellets of filling material based on gutta-percha after covering the root canal walls with a thin layer of AH Plus sealant. In this way, the research thesis was confirmed.

Evaluation of the sealer/gutta-percha ratio on sets of root section surfaces of some extracted teeth sealed using the cold lateral condensation technique

Canal filling must be well adapted to the walls of the root canal to prevent bacterial infiltration. Endodontic seals play an essential role in ensuring tightness, without which the canal filling would suffer infiltrations. This study aimed to evaluate the areas occupied by the two components of the canal filling, as well as the sealer/gutta-percha ratio in the root canals of the maxillary central incisors after their filling using the cold lateral condensation technique with gutta-percha. Thirty extracted upper central incisors were rotatably prepared with ProTaper Universal up to F3 and sealed using the cold lateral condensation technique with gutta-percha. After setting the sealer, the roots of the teeth were sectioned perpendicularly to 1 (L1), 3 (L3), 6 (L6), and 8 (L8) mm from the apex. The surface of the sections was analyzed with a Leica EZ4D stereomicroscope and photographed at two magnification orders: 10x and 25x. The areas corresponding to the gutta-percha, sealer, gaps, and root canal were expressed in pixels using the ImageJ software, version 1.50i. The difference in the representation of sealer areas, gutta-percha and voids was statistically significantly different for all four sections analyzed. The best adaptation of the canal obturation was observed in L1 and L3. The gutta-percha area was statistically significantly higher than that of the sealer for the L1, L3, and L6 levels, while the sealer/gutta-percha ratio recorded the lowest value at the L3 level (0, 30) and the highest at its L8 (0.70) level, without registering statistically significant differences regarding the area at the four analyzed levels. The voids were mostly absent or recorded a minimal percentage area (<1%). Cold lateral condensation of gutta-percha has led to a good adaptation of gutta-percha to the root canal wall, with a small amount of sealer, especially to the sections made at 3 mm from the apex. Given the limitations of this study, we noted that the voids were few – observed in the 6 and 8 mm sections – and were negligible in many cases.

Complete Obturation-Cold Lateral Condensation vs. Thermoplastic Techniques: A Systematic Review of Micro-CT Studies

To prevent re-infection and provide a hermetic seal of the root canal system, an endodontist must aim to produce a void-free obturation. This review aimed to compare the completeness of root canal obturation between the two most prevalent methods-cold lateral condensation and warm gutta-percha techniques-using micro-CT (PROSPERO reg no. 249815).

MATERIALS AND METHODS

A search of Scopus, Embase, PubMed (Medline via PubMed), and Web of Science databases was done without any time restriction according to the PRISMA protocol. Articles that compared both techniques and were published in English were included. Data was extracted and the risk of bias was assessed using an adapted tool based on previous studies.

RESULTS

A total of 141 studies were identified by the search. Following the screening and selection of articles, 9 studies were included for review. Data was extracted manually and tabulated. Most studies had a moderate risk of bias. None determined operator skill in both methods before comparison. The data extracted from the included studies suggests that both techniques produce voids in the obturation. The thermoplasticized gutta-percha techniques may result in fewer voids compared to cold lateral condensation.

CONCLUSION

Considering the limitations of the included studies, it was concluded that neither technique could completely obturate the root canal. Thermoplasticized gutta-percha techniques showed better outcomes despite a possible learning bias in favor of cold lateral condensation. Establishing operator skills before comparison may help reduce this bias.

Calcium Silicate-Based Root Canal Sealers: A Narrative Review and Clinical Perspectives

Over the last two decades, calcium silicate-based materials have grown in popularity. As root canal sealers, these formulations have been extensively investigated and compared with conventional sealers, such as zinc oxide-eugenol and epoxy resin-based sealers, in in vitro studies that showed their promising properties, especially their biocompatibility, antimicrobial properties, and certain bioactivity. However, the consequence of their higher solubility is a matter of debate and still needs to be clarified, because it may affect their long-term sealing ability. Unlike conventional sealers, those sealers are hydraulic, and their setting is conditioned by the presence of humidity. Current evidence reveals that the properties of calcium silicate-based sealers vary depending on their formulation. To date, only a few short-term investigations addressed the clinical outcome of calcium silicate-based root canal sealers. Their use has been showed to be mainly based on practitioners' clinical habits rather than manufacturers' recommendations or available evidence. However, their particular behavior implies modifications of the clinical protocol used for conventional sealers. This narrative review aimed to discuss the properties of calcium silicate-based sealers and their clinical implications, and to propose rational indications for these sealers based on the current knowledge.

Microscopic and chemical evaluation of the filling quality of five obturation techniques in oval-shaped root canals

OBJECTIVES

The aim of this study was to assess the filling quality of five obturation techniques in oval-shaped root canals.

MATERIALS AND METHODS

A total of 212 mandibular first molars with one distal oval canal were selected. Distal canals, shaped with WaveOne Gold Primary, were randomly divided in five groups (n = 40) for obturation: continuous wave condensation, GuttaCore, Thermafil, single cone with AH plus, and single cone with BioRoot RCS. The proportions of gutta-percha-filled areas (GPFA), sealer-filled areas (SFA), void areas (VA), and the sealer/gutta tags into dentinal tubules at 4 mm and 2 mm from the apex were analyzed by an optical numeric microscope, SEM, and energy-dispersive X-ray (EDX). Data were then compared by Kruskal-Wallis one-way ANOVA on ranks (α = 0.05).

RESULTS

At 4 mm, a statistically significant higher GPFA and lower SFA were observed in the GuttaCore and Thermafil groups compared with the 3 other groups. A statistically significant lower VA was observed in the continuous wave condensation, GuttaCore, and Thermafil groups than in the two single-cone groups. At 2 mm, there were a statistically significant higher GPFA and lower SFA and VA in GuttaCore and Thermafil groups than in the 3 other groups. At the two levels investigated, the presence of gutta-percha tags was clearly demonstrated for GuttaCore and Thermafil groups; no tags were observed in the 3 other groups.

CONCLUSIONS

Obturation quality was overall improved in GuttaCore and Thermafil groups.

CLINICAL RELEVANCE

Carrier-based techniques may significantly improve the filling quality compared to continuous wave condensation and single-cone technique. The single-cone technique might have inherent limitations especially in oval root canals regardless of the sealer used.

Volumetric Evaluation of 5 Root Canal Obturation Methods in TrueTooth 3-dimensional-Printed Tooth Replicas Using Nano-computed Tomography

INTRODUCTION

The aim of this study was to evaluate the volumes of total obturation and voids in different obturation techniques using nano-computed tomographic imaging. The null hypothesis was that the obturation technique and the materials used have no effect on the total volume of obturation or the total volume of voids.

METHODS

Fifty maxillary left central incisor 3-dimensional-printed replicas (TrueTooth; Dental Engineering Laboratories, Santa Barbara, CA) were instrumented and randomly assigned to 5 different obturation groups (n = 10): single cone with EndoSequence Gutta-Percha Points (Brasseler USA, Savannah, GA) and Ribbon Sealer (Dentsply Sirona, Tulsa, OK) (SC1), single cone with BC 150 Series Gutta-Percha Points (Brasseler USA) and EndoSequence BC Sealer (Brasseler USA) (SC2), continuous wave with EndoSequence Gutta-Percha Points and Ribbon Sealer (CW), GuttaCore carrier obturation (Dentsply Sirona) and Ribbon Sealer (GC), and cold lateral condensation with EndoSequence Gutta-Percha Points and Ribbon Sealer (CL). After obturation, nano-computed tomographic images were obtained, and volumetric analysis was performed. Statistical analysis using 1-way analysis of variance (ANOVA). The level of significance was set at 5% (P < .05).

RESULTS

The 1-way ANOVA for total obturation indicated a statistically significant effect of group on obturation. Post hoc tests revealed a significant difference between the SC2, CW, and CL groups compared with the SC1 and GC groups. The 1-way ANOVA for calculated voids indicated a statistically significant effect of group on voids. Post hoc tests revealed significant differences between the SC1 group and the GC and CL groups.

CONCLUSIONS

This study concluded that obturation technique and the materials used significantly affect the total volume of obturation material and potential for voids.

Percentage of Gutta-Percha-, Sealer-, and Void-Filled Areas in Oval-Shaped Root Canals Obturated with Different Filling Techniques: A Confocal Laser Scanning Microscopy Study

Objective  This study compared different obturation techniques, analyzing percentage of areas filled with gutta-percha, sealer, and voids (PGFA, PSFA, and PVFA, respectively) in oval-shaped root canals.

Materials and Methods  A total of 60 extracted human mandibular central incisors were decoronated, instrumented, and irrigated using the same protocol. After drying, the root canal was filled with AH Plus labeled with 0.1% rhodamine B dye using a Lentulo spiral. The filling procedure was performed by dividing the teeth into four groups according to the respective technique: G1, cold lateral condensation; G2, continuous wave of condensation; G3, modified cold lateral condensation using an F3 master cone; and G4, modified continuous wave of condensation using an ISO (International Organization for Standardization) sized 30 gutta-percha cone. Then, slices measuring 1.5 mm in thickness were obtained 3 and 6 mm from the apex and evaluated by confocal laser scanning microscopy to determine PGFA, PSFA, and PVFA.

Statistical Analysis  The data were analyzed statistically with analysis of variance and Games-Howell’s tests ( p = 0.05).

Results  The groups showed no significant differences in the apical third (3 mm from the apex). In the middle third (6 mm from the apex), G3 and G1 showed higher PGFA and PVFA, respectively. G3 showed lower PSFA than G2 and G4. Both cold techniques (G1 and G3) promoted lower PSFA than both warm techniques (G2 and G4).

Conclusions  Notwithstanding the limitations of this in vitro study, PGFA, PSFA, and PVFA ranged significantly only in the middle third, as observed by the different filling techniques. Higher PGFA and PVFA values were obtained for G3 and G1, respectively. Both cold techniques promoted lower PSFA than both warm techniques.

Microscopic and Chemical Assessments of the Filling Ability in Oval-Shaped Root Canals Using Two Different Carrier-Based Filling Techniques

Objectives The aim of this study was to assess the filling ability in oval-shaped canals using two different carrier-based filling techniques.

Materials and Methods Twenty-four human mandibular premolars with one oval canal were selected. Canals were shaped using WaveOne Gold Primary and ProGlider. Samples were divided into two groups and filled as follows: Thermafil and GuttaCore. The proportions of gutta-percha-filled areas (GPFAs), sealer-filled areas (SFAs), and void areas (VA), at 2 and 5 mm, were analyzed using optical numeric microscope, scanning electron microscope, and energy-dispersive X-ray.

Statistical Analysis Data were compared by Kruskal–Wallis one-way analysis of variance on ranks, with statistical significance set at α = 0.05.

Results At 2 and 5 mm distances from the apex, this study discloses no statistically different filling ability for the two techniques. Concerning each sample treated using both filling systems, the presence of tags was visualized. At working length (WL)-5, and WL-2, the maximum tag penetration depth for the GuttaCore group into the dentinal tubules was, respectively, 96 μm and 48 μm, whereas the values in the thermafil group were 109 μm, and 55 μm, respectively.

Conclusions Our results clearly show that Thermafil and GuttaCore can fill oval-shaped canals in appropriate way. Furthermore, we can state that the GuttaCore obturator allows to preserve the same filling ability than Thermafil obturator, in view of the fact that there was no difference, in terms of GPFA, SFA, and VA between the two different carrier-based obturation techniques.

Microcomputed tomographic evaluation of techniques for warm gutta-percha obturation

Transparent epoxy resin root canal models were used to evaluate vertical condensation techniques for obturating lateral canals. The root canal model was configured with a straight main root canal and four right-angled lateral canals at 1.0 and 3.0 mm from the apex. Root canal obturation was performed with Thermafil, Obtura II, or NT condenser. Obturation volume in lateral canals was measured by three-dimensional microcomputed tomography, and one-way analysis of variance was used to analyze differences between groups. Lateral canals at 1.0 and 3.0 mm were uniformly filled by all obturation methods. Among the three obturation methods, Thermafil resulted in the highest obturation volumes for all lateral canals.

Comparison of microtomography and optical coherence tomography on apical endodontic filling analysis

OBJECTIVES

To comparein vitro differences in the apical filling regarding working length (WL) change and presence of voids and to validate optical coherence tomography (OCT) in comparison with computerized microtomography (µCT) for the detection of failures in the apical filling.

METHODS

Forty-five uniradicular teeth with round canals, divided into groups (n = 15) following the obturation protocols: LC (lateral condensation), TMC (thermomechanical compaction) and SC (single cone). Samples were scanned using µCT (parameters: 80 kV, 222 µA, and resolution of 11 µm), OCT (parameters: SSOCT, 1300 nm and axial resolution of 12 µm), and periapical digital radiography. The images were analyzsed by two blind and calibrated observers using ImageJ software to measure the boundary of the obturation WL and voids presence. Categorical and metric data were submitted to inferential analysis, and the validity of the OCT as a diagnostic test was assessed with performance and reliability tests.

RESULTS

The WL average remained constant for all obturation techniques and image methods. OCT showed adequate sensitivity and specificity to detect voids in the WL of apical obturations in vitro in comparison with µCT. Both image methods found a higher number of voids for LC technique (µCT p = 0.011/OCT p = 0.002).

CONCLUSIONS

OCT can be used in apical obturation voids assessment and the LC technique revealed more voids with larger dimensions.

In vitro comparison of gutta-percha-filled area percentages in root canals instrumented and obturated with different techniques

Purpose:

To evaluate the efficacy of different obturation techniques in root canals instrumented either by hand or rotary instruments with regard to the percentage of gutta- percha-filled area (PGFA).

Materials and Methods:

One hundred and sixty extracted mandibular premolars with single, straight root canals were studied. Root canals were prepared to an apical size of 30 by hand with a modified crown-down technique or the ProTaper and HEROShaper systems. Teeth were divided into eight groups (n=20) according to the following instrumentation and obturation techniques: G1: Hand files+lateral condensation (LC), G2: Hand files+Thermafil, G3: ProTaper+LC, G4: ProTaper+single-cone, G5: ProTaper+ProTaper-Obturator, G6: HEROShaper+LC, G7: HEROShaper+single-cone, G8: HEROShaper+HEROfill. Horizontal sections were cut at 1, 3, 5, 7, 9, 11 and 13 mm from the apical foramen. A total of 1120 sections obtained were digitally photographed under a stereomicroscope set at 48X magnification. The cross-sectional area of the canal and the gutta-percha was measured by digital image analysis and the PGFA was calculated for each section.

Results:

The mean of the PGFA in Thermafil (G2), ProTaper-Obturator (G5) and HEROfill (G8) groups was significantly higher than the other groups. In G3 and G4, PGFA showed no significant difference in the apical segments whereas PGFA was significantly higher at the middle and coronal segments in G3. In G6 and G7, PGFA showed no significant difference in the apical and middle segments whereas PGFA was significantly higher at the coronal segments in G6.

Conclusion:

The carrier-based gutta-percha obturation systems revealed significantly higher PGFA in comparison to single-cone and lateral condensation techniques.

Comparative evaluation of canal cleaning ability of various rotary endodontic filesin apical third: A scanning electron microscopic study

BACKGROUND

The purpose of this study was to evaluate the canal cleaning ability of three novel endodontic rotary instruments and compare with ProTaper files as a control in apical third of root canals under scanning electron microscopy (SEM).

MATERIALS AND METHODS

Eighty freshly extracted mandibular premolars were selected according to inclusion criteria. Buccal cusp tips were ground to ensure having a flat coronal reference point with a total tooth length of 16 mm for all samples. Teeth were divided equally into four groups: Group I (ProTaper group), Group II (ProTaper next group), Group III (variable taper group), and Group IV (self-adjusting file [SAF] group). Using SEM, the dentinal surfaces were observed and rated at apical thirds with a magnification of ×1000 for the presence/absence of smear layer and debris. Descriptive analysis was performed, and analysis of variance with Bonferroni post hoc test was carried out for comparison between the groups, at a significance level of 0.05.

RESULTS

There was statistically significant difference between Group II and Group IV for debris (P = 0.047) and smear layer (P = 0.037).

CONCLUSION

In apical third of root canal, SAF showed statistically significant canal cleaning ability due to combined effect of continuous streaming irrigation with effectively replacing the irrigant from the apical portion of the root canal, irrigants activation through the creation of turbulence, and its self-adapting design to root canal anatomy with a scrubbing motion on the canal walls.

Radiological, stereological, and microscopic evaluation of the quality of canal fillings in oval-shaped root canals prepared with self-adjusting file

The aim of this study was to evaluate the quality of the canal fillings performed by thermoplastic technique (Herofill) and cold lateral condensation (CLC) techniques in oval shaped canals following self-adjusting file (SAF) preparation using radiological, stereological, and microscopic evaluation methods. Twelve pairs of oval-shaped root canals were prepared with SAF and filled using CLC (n = 12) or the Herofill system (n = 12). The quality of the root canal filling was evaluated by (i) scoring bidirectional storage phosphor plate images, (ii) stereological (volumetric) analysis of cone beam computerized tomography (CBCT) images, and (iii) microscopic analysis of the cross-sectioned area of the canal and gutta-percha via image analysis software. Chi-square test, t-test, and Mann-Whitney U-tests were used respectively (p < 0.05) for the aforementioned evaluations. 58.33% of the fillings (total n = 24) that were found to be sufficient in a bucco-lingual (BL) projection were considered insufficient in the mesio-distal (MD) projection according to radiological scoring. The difference in the findings between the two types of projections (BL and MD) was significant (p < 0.05). The results of the stereological evaluation of CBCT images and image analysis of cross-sections showed no statistically significant difference between the CLC and Herofill (p > 0.05). Herofill was not superior to cold lateral compaction. Stereology can be used to obtain unbiased information about the volume of root canal fillings. Both filling techniques failed to achieve the desirable goal of 0% empty volume in all of the cases and all evaluation systems confirmed this result. SCANNING 38:427-433, 2016. © 2015 Wiley Periodicals, Inc.

Volume of sealer in the apical region of teeth filled by different techniques: a micro-CT analysis

The volume of sealer in the apical 1 mm of teeth filled using different techniques was evaluated by micro-commuted tomography (micro-CT). Sixty-four maxillary central incisors were prepared using NiTi rotary instruments. Teeth were randomly distributed into four groups according to root canal sealers (AH Plus, Endofill, Sealapex, and Sealer 26) and subdivided into two subgroups according to the filling techniques (active and passive lateral condensation; n = 8 each). Subsequently, teeth were examined using the 1174 SkyScan micro-CT device. Images were reconstructed using the NRecon software, and the sealer volume (mm3) in the apical region was analyzed using the two-way ANOVA and post-hoc Student-Newman-Keuls test (α = 0.05). The lowest volume of sealer was observed in teeth filled with Sealapex (0.100 ± 0.009) and Endofill (0.103 ± 0.010). The highest volume was observed in teeth filled with AH Plus (0.112 ± 0.008) and Sealer 26 (0.109 ± 0.018) (p > 0.05). Regarding the filling technique, a lower sealer volume was observed using the active lateral condensation technique compared with that using the passive lateral condensation technique (0.100 ± 0.010 vs. 0.111 ± 0.012) (p < 0.05). Therefore, the lowest volume of sealer was observed in teeth filled with Sealapex and Endofill using the active lateral condensation technique.

In vitro evaluation of carrier based obturation technique: a CBCT study

AIM

The goal of the study was to compare the ability of two different carrier based obturation (CBO) techniques to reach working length and fill in three-dimensions root canal systems, by using CBCT.

MATERIALS AND METHODS

Twenty-six extracted molars were scanned with CBCT and 40 curved canals were selected (between 30° and 90°) and divided in two similar groups (n=20). All canals were prepared up to size 25 taper .06 using nickel-titanium instrumentation. The canals in the Group SC were obturated using Soft-Core obturators (Kerr, Romulus, Mi, USA), while Group TH canals (n= 20) were obturated using Thermafil Endodontic Obturators (Tulsa Dental Products, Tulsa, OK, USA), strictly following manufacturers' instructions for use. The obturations were analyzed by means of CBCT to measure the distance from the apical limit of obturation to the apical foramen and the presence of voids inside root canals.

RESULTS

There was no significant difference between the two groups in the mean distance of the apical extent of the obturation (t test, p>0.05). Overfilling occurred in only 3 cases (2 in Group TH and 1 in Group SC). The percentages of voids in both groups were very low with no significant difference (Z test, p>0.05).

CONCLUSIONS

The two tested CBO techniques showed similar positive results in terms of performance, even if, after checking with verifiers, in most cases the size of the selected Soft-Core obturator was one size smaller than Thermafil.

Apical filling characteristics of carrier-based techniques vs. single cone technique in curved root canals

OBJECTIVES

In this in vitro study, we assessed filling characteristics (adaptation, homogeneity, sealer percentage, position of the carrier) of warm and cold obturation methods in curved root canals.

MATERIALS AND METHODS

A reciprocating method was used to prepare 90 curved roots (25 ° average curvature) to an apical size of 25.08. They were then obturated with either (A) Guttafusion (VDW, Munich, Germany), (B) Thermafil (Maillefer, Ballaigues, Switzerland) or (C) single cone technique using 25.08 gutta-percha (VDW) and sealer (2Seal easymix) (n = 30 each group). Five sections in 1-mm steps were obtained from each root, beginning 1 mm short of the apex. The percentage of voids in contact with root canal walls (PVO), the proportion of voids per area (PVA) and the percentage of sealer per area (PSA) were measured.

RESULTS

Little to no differences between Guttafusion and Thermafil were seen in curved root canals with respect to adaptation and homogeneity in the apical region. Both methods showed significantly better adaptation and homogeneity than the single cone technique. The proportion of sealer was significantly greater when roots were obturated with Guttafusion than with Thermafil, but both warm obturation techniques had significantly smaller sealer areas than the single cone technique.

CONCLUSIONS

Compared to the single cone technique, a more favourable root canal filling with less sealer could be expected from both warm obturation techniques in curved root canals.

CLINICAL RELEVANCE

The easier-to-handle Guttafusion leads to comparable results as Thermafil in curved root canals.

Efficacy of Reciproc(®) and Profile(®) Instruments in the Removal of Gutta-Percha from Straight and Curved Root Canals ex Vivo

Objectives

To compare the efficacy of Reciproc^® (VDW GmbH) and ProFile^® (Dentsply Maillefer) instruments at removing gutta-percha from straight and curved root canals ex vivo filled using the cold lateral condensation and GuttaMaster^® (VDW GmbH) techniques.

Material and Methods

Forty mesial roots of mandibular molars with two curved canals and 80 single-rooted teeth with straight root canals, a total of 160 root canals, were randomly assigned to eight groups (canals per group = 20) according to filling technique, retreatment instrument and root canal curvature as follows: Group I, cold lateral condensation/ProFile^®/straight; Group II, cold lateral condensation/ProFile^®/curved; Group III, cold lateral condensation/Reciproc^®/straight; Group IV, cold lateral condensation/Reciproc^®/curved; Group V, GuttaMaster^®/ProFile^®/straight; Group VI, GuttaMaster^®/ProFile^®/curved; Group VII, GuttaMaster^®/Reciproc^®/straight; and Group VIII, GuttaMaster^®/Reciproc^®/curved. The following data were recorded: procedural errors, retreatment duration and canal wall cleanliness. Means and standard deviations were calculated and analysed using the Kruskal-Wallis test, one-way analysis of variance and Tukey’s test (P < 0.05).

Results

Reciproc^® instruments were significantly faster than ProFile^® instruments at removing GuttaMaster^® from both straight (P = 0.0001) and curved (P = 0.0003) root canals. Reciproc^® were statistically more effective than ProFile^® instruments in removing GuttaMaster^® from straight root canals (P = 0.021). Regardless of filling technique or retreatment instrument, gutta-percha was removed more rapidly from curved than from straight root canals (P = 0.0001).

Conclusions

Neither system completely removed filling material from the root canals. Compared with ProFile^® instruments, Reciproc^® instruments removed GuttaMaster^® filling material from straight and curved root canals more rapidly.

Comparison of bacterial leakage resistance of various root canal filling materials and methods: Confocal laser-scanning microscope study

This study evaluated the bacterial leakage resistance and root canal lining efficacy of various root canal filling materials and methods by using confocal laser-scanning microscope (CLSM). Sixty extracted human premolars with mature apex and single root canal were randomly divided into 2 control groups and 4 experimental groups. Group CW was filled with continuous wave technique using gutta-percha and AH Plus sealer. Group GC was coated with AH-Plus sealer and then obturated with soften GuttaCore. Group GF was obturated using GuttaFlow and gutta-percha. Group EM was filled with EndoSeal MTA and gutta-percha using ultrasonic vibration. The AH-Plus, GuttaFlow, and EndoSeal were labeled with Hoechst 33342 to facilitate fluorescence. The obturated root tip was incubated with Carboxyfluorescein diacetate succinimidyl ester (CFSE)-stained E. faecalis for 14 days. CLSM was performed to evaluate the sealer distribution and bacterial leakage for the apical 1-, 2-, 3-mm specimens. Statistically significant differences were determined by 1-way ANOVA with Tukey's post-hoc test and Pearson's correlation analysis. Group EM showed the better sealer distribution score than the other groups (p < 0.05). Group CW and group GC exhibited the less bacterial leakage than the group GF, while group EM showed the similar bacterial leakage score with the groups CW and GC. There was no significant correlation between the sealer distribution and bacterial leakage (p > 0.05). Under the conditions of this study, different root canal filling materials and methods showed different efficacy for canal distribution and bacterial leakage resistance.

Evaluation of Root Canal Preparation Using Rotary System and Hand Instruments Assessed by Micro-Computed Tomography

Background

Complete mechanical preparation of the root canal system is rarely achieved. Therefore, the purpose of this study was to evaluate and compare the root canal shaping efficacy of ProTaper rotary files and standard stainless steel K-files using micro-computed tomography.

Material/Methods

Sixty extracted upper second premolars were selected and divided into 2 groups of 30 teeth each. Before preparation, all samples were scanned by micro-computed tomography. Thirty teeth were prepared with the ProTaper system and the other 30 with stainless steel files. After preparation, the untouched surface and root canal straightening were evaluated with micro-computed tomography. The percentage of untouched root canal surface was calculated in the coronal, middle, and apical parts of the canal. We also calculated straightening of the canal after root canal preparation. Results from the 2 groups were statistically compared using the Minitab statistical package.

Results

ProTaper rotary files left less untouched root canal surface compared with manual preparation in coronal, middle, and apical sector (p<0.001). Similarly, there was a statistically significant difference in root canal straightening after preparation between the techniques (p<0.001).

Conclusions

Neither manual nor rotary techniques completely prepared the root canal, and both techniques caused slight straightening of the root canal.

A microcomputed tomography-based comparison of root canal filling quality following different instrumentation and obturation techniques

OBJECTIVE

With a microcomputed tomography (microCT) imaging device, we aimed to quantitatively evaluate root canal fillings after commonly used endodontic procedures and also tested the suitability of microCT for this purpose.

MATERIALS AND METHODS

Eighty single roots were instrumented and obturated with gutta-percha and Tubli-Seal. They were divided into 4 groups of 20. The Hand groups were instrumented with hand files and filled with thermoplastic (Th) compaction and cold lateral (CL) condensation, i.e. Hand-Th and Hand-CL, respectively. The Rot groups, i.e. Rot-Th and Rot-CL, were instrumented with a rotary ProFile system and filled as above. The roots were scanned and 3-dimensional (3D) visualization was obtained. The number, size, percentage of volume and distribution of voids at the filling/dentine interface (i-voids) and voids surrounded by filling material (s-voids) were measured.

RESULTS

Canal fillings differed significantly with regard to the size of both types of voids and the average number of i-voids. All canals presented a low volume of voids. The highest percentage (0.69%) was found for i-voids in the Hand-CL group, while the lowest volume (0.11% for s-voids and 0.14% for i-voids) was in the Hand-Th canals. Apically, in the last 3 mm, i-voids were observed mainly in the Th groups, and s-voids occurred mostly in the coronal part of the canal filling in all cases.

CONCLUSION

MicroCT was a useful tool for 3D quantitative evaluations of these root canal fillings. None of the root canal instrumentation and filling methods ensured void-free obturation. CL condensation produced mainly i-voids. With Th compaction, internal s-voids were particularly common, but there were mainly i-voids in the apical part.

The self-adjusting file (SAF) system: An evidence-based update

Current rotary file systems are effective tools. Nevertheless, they have two main shortcomings: They are unable to effectively clean and shape oval canals and depend too much on the irrigant to do the cleaning, which is an unrealistic illusionThey may jeopardize the long-term survival of the tooth via unnecessary, excessive removal of sound dentin and creation of micro-cracks in the remaining root dentin. The new Self-adjusting File (SAF) technology uses a hollow, compressible NiTi file, with no central metal core, through which a continuous flow of irrigant is provided throughout the procedure. The SAF technology allows for effective cleaning of all root canals including oval canals, thus allowing for the effective disinfection and obturation of all canal morphologies. This technology uses a new concept of cleaning and shaping in which a uniform layer of dentin is removed from around the entire perimeter of the root canal, thus avoiding unnecessary excessive removal of sound dentin. Furthermore, the mode of action used by this file system does not apply the machining of all root canals to a circular bore, as do all other rotary file systems, and does not cause micro-cracks in the remaining root dentin. The new SAF technology allows for a new concept in cleaning and shaping root canals: Minimally Invasive 3D Endodontics.

Quality of obturation achieved by an endodontic core-carrier system with crosslinked gutta-percha carrier in single-rooted canals

OBJECTIVES

The present study examined the quality of obturation in root canals obturated by GuttaCore, a gutta-percha-based core-carrier system with a cross-linked thermoset gutta-percha carrier, by comparing the incidence of gaps and voids identified from similar canals obturated by cold lateral compaction or warm vertical compaction.

METHODS

Thirty single-rooted premolars with oval-shaped canals were shaped and cleaned, and obturated with one of the three obturation techniques (N=10): GuttaCore, warm vertical compaction or cold lateral compaction. Filled canals were scanned with micro-computed tomography (micro-CT); reconstructed images were analysed for the volumetric percentage of gaps and voids at three canal levels (0-4mm, 4-8mm and 8-12mm from working length). The roots were subsequently sectioned at the 4-mm, 8-mm and 12-mm levels for analyses of the percentage of interfacial gaps, and area percentage of interfacial and intracanal voids, using scanning electron microscopy (SEM) to examine negative replicas of root sections. Data were analysed with parametric or non-parametric statistical methods at α=0.05.

RESULTS

Both micro-CT and SEM data indicated that canals obturated with GuttaCore core-carriers had the lowest incidence of interfacial gaps and voids, although the results were not significantly different from canals obturated by warm vertical compaction. Both the GuttaCore and the warm vertical compaction groups, in turn, had significantly lower incidences of gaps and voids than the cold lateral compaction group.

CONCLUSIONS

Because of the similarity in obturation quality between GuttaCore and warm vertical compaction, practitioners may find the GuttaCore core-carrier technique a valuable alternative for obturation of oval-shaped canals.

CLINICAL SIGNIFICANCE

The quality of obturation achieved by GuttaCore in single-rooted canals is not significantly different from that achieved by warm vertical compaction.

Fiber-post bond strength in canals obturated with a cross-linked gutta-percha core obturator

The aim of this in-vitro study was to evaluate the bond strength of fiber posts cemented in a root canal filled using various root-canal obturation techniques. A total of 33 monoradicular samples, treated endodontically, were randomly assigned to three groups according to the root-canal obturation technique: group 1, continuous-wave technique; group 2, plastic-obturator-core technique; and group 3, cross-linked gutta-percha obturator-core technique. Fiber posts were luted in each sample and each was sectioned perpendicular to the post axis. The push-out test was performed using a universal machine and the maximum failure load was recorded in MPa mm(-2) . Several samples were randomly chosen for scanning electron microscopy evaluation. The mean debris and dentinal tubule-opening scores were calculated separately in the coronal and apical portions. Bond strength was significantly higher in group 1 than in groups 2 and 3. Debris scores were significantly higher in the apical portion of groups 2 and 3 than in group 1. Within the limitations of this study it can be affirmed that thermoplasticized alpha gutta-percha seemed to worsen the cleaning of post-space walls and hence reduced fiber-post bond strength.

The effect of a diode laser and traditional irrigants on the bond strength of self-adhesive cement

PURPOSE

The purpose of this study was to compare the effect of a diode laser and traditional irrigants on the bond strength of self-adhesive cement.

MATERIALS AND METHODS

Fifty-five incisors extracted due to periodontal problems were used. All teeth were instrumented using a set of rotary root canal instruments. The post spaces were enlarged for a No.14 (diameter, 1.4 mm) Snowlight (Abrasive technology, OH, USA) glass fiber reinforced composite post with matching drill. The teeth were randomly divided into 5 experimental groups of 11 teeth each. The post spaces were treated with the followings: Group 1: 5 mL 0.9% physiological saline; Group 2: 5 mL 5.25% sodium hypochlorite; Group 3: 5 mL 17% ethylene diamine tetra acetic acid (EDTA), Group 4: 37% orthophosphoric acid and Group 5: Photodynamic diode laser irradiation for 1 minute after application of light-active dye solution. Snowlight posts were luted with self-adhesive resin cement. Each root was sectioned perpendicular to its long axis to create 1 mm thick specimens. The push-out bond strength test method was used to measure bond strength. One tooth from each group was processed for scanning electron microscopic analysis.

RESULTS

BOND STRENGTH VALUES WERE AS FOLLOW: Group 1 = 4.15 MPa; Group 2 = 3.00 MPa; Group 3 = 4.45 MPa; Group 4 = 6.96 MPa; and Group 5 = 8.93 MPa. These values were analysed using one-way ANOVA and Tukey honestly significant difference test (P<.05). Significantly higher bond strength values were obtained with the diode laser and orthophosphoric acid (P<.05). There were no differences found between the other groups (P>.05).

CONCLUSION

Orthophosphoric acid and EDTA were more effective methods for removing the smear layer than the diode laser. However, the diode laser and orthophosphoric acid were more effective at the cement dentin interface than the EDTA, Therefore, modifying the smear layer may be more effective when a self-adhesive system is used.

Carrier-based root canal filling materials: a literature review

A review of the literature on the use of carrier based obturation materials focusing on Thermafil and Resilon based obturator (RealSeal 1) are presented in this article. The review addressed the history, apical leakage, coronal leakage, biocompatibility, sealing ability and clinical success of Thermafil and RealSeal 1. Based on the studies gathered, this review concluded that both treatment techniques (Thermafil and RealSeal 1) did not provide excellent apical sealing ability. More research should be done to try to overcome their main drawback, its sealing ability.

The use of instruments by Iranian endodontics and general practioners

AIM

The current clinical practice of endodontics involves utilization of a variety of new technological advances and materials. Technologies available for use in endodontic offices today include battery or electric motors using NiTi rotary file systems, new generation of electronic apex locators (EALs), improved digital radiographic sensors, surgical microscopes, and ultrasonic units. The aim of this study was to determine the prevalence and use of newer technologies among Iranian dental practitioners.

MATERIALS AND METHODS

The population under study included the dental practitioners participating in the 49th and 50(th) Congress of Dentistry, who were selected with a simple sampling method. Data was collected by questionnaires which were completed by the participants in an anonymous manner. The contingency table and chi-squared test were used for data analysis by SPSS 13.5 software.

RESULTS

A total of 700 dental practitioners participated in the study; NiTi rotary systems were used by 50.1%; electronic apex locators were often employed by 46.3%; 21.7% reported that ultrasonic units were often used. Only 1.1% frequently used surgical microscopes. Males and females differed with respect to the use of newer technologies (P<0.05).

CONCLUSION

Based on the results of the present study, it seems necessary for dentists to take part in continuing dental education programs related to the newer technologies to improve their knowledge and practice.

Formulation of meningococcal capsular polysaccharide vaccine-loaded microparticles with robust innate immune recognition

Neisseria meningitidis is a leading cause of bacterial meningitis and sepsis associated with a high mortality rate. Capsular polysaccharides (CPSs) are a major virulence factor and form the basis for serogroup designation and protective vaccines. The current polysaccharide meningococcal vaccines are available but are very expensive and require chemical conjugation. Here, we report a novel meningococcal vaccine formulation consisting of meningococcal CPS polymers encapsulated in albumin-based biodegradable microparticles that slowly release antigen and induce robust innate immune responses. Vaccines that elicit innate immunity are reported to have enhanced and protective adaptive immune responses. In this study, the meningococcal CPS-loaded microparticles, but not the empty microparticles, induced the release of IL-8, TNF-α and IL-1β, enhanced phagocytic capacity and induced robust autophagy in macrophages. The novel meningococcal vaccine microparticles are robustly taken up by macrophages and elicit strong innate immune responses that enhance antigen presentation which is a prerequisite for inducing adaptive immunity.

Comparative analysis of carrier-based obturation and lateral compaction: a retrospective clinical outcomes study

The purpose of this retrospective study was to compare the outcome of primary endodontic treatment using a standardized cleaning and shaping technique and obturation with either lateral compaction or carrier-based obturation. Patients received primary endodontic treatment in the predoctoral dental clinic using a standardized cleaning and shaping protocol. All root canals were obturated using AH Plus(TM) sealer with lateral compaction of gutta-percha (LC) or carrier-based obturation (CBO). A total of 205 cases met the inclusion criteria. 71 teeth in 60 patients were recalled after 2 years and evaluated both clinically and radiographically by two independent examiners. Success was defined as a lack of clinical symptoms and a normal periodontal ligament space or reduction in size of a previously existing periapical radiolucency. Chi-square and logistic regression were used for statistical analysis with a significance level of P < 0.05. There was no difference in success rates between cases obturated with LC or CBO (P = 0.802); overall success rate was 83%. Molars had a significantly lower success rate (53%) than premolar and anterior teeth (89%) (P = 0.005), irrespective of the obturation technique used. When a standardized cleaning and shaping protocol was used by predoctoral dental students in a controlled university setting, there was no difference in success rates between cases obturated with LC or CBO.

A comparative evaluation of gutta-percha filled areas in curved root canals obturated with different techniques

The aim of this study was to compare different obturation techniques in severely curved canals in terms of the percentage of gutta-percha filled area and voids. The obturation times and the incidence of extrusion of filling material were also compared. Curved root canals (curvature, 25-35°) of 48 extracted human teeth were enlarged with Mtwo rotary NiTi instruments and obturated as follows: Group A: 0.04/35 matched-single-cone; Group B: cold lateral compaction with 0.04/35 gutta-percha master cone; Group C: warm vertical compaction; Group D: lateral compaction with standardized gutta-percha master cone. In all groups AHPlus was used as sealer. The teeth were sectioned horizontally at 2, 3, 4, 6 and 8 mm from the apex. The total area of each canal segment was measured and the areas of gutta-percha, sealer and voids were converted to percentages of the total area. Data were subjected to the Kruskal-Wallis and post hoc Dunn test. Obturation times were compared using ANOVA and post hoc Student-Newman-Keuls test. The matched-single-cone obturation (group A) was significantly the fastest method while warm vertical compaction (group C) required significantly more time than all other techniques (p < 0.05). No significant differences were obtained between the groups in terms of percentage of voids at any level (p > 0.05). At all levels, groups B, C, and D produced significantly higher gutta-percha filled areas (p < 0.05) and lower sealer-filled areas (p < 0.05) than group A. No significant differences were found between groups B, C, and D (p > 0.05) regarding gutta-percha and sealer-filled areas. Within the limitations of the in vitro study, it can be concluded that lateral compaction of greater taper gutta-percha cones is a fast and efficient method for obturation of curved canals.

The quality of root canal preparation and root canal obturation in canals treated with rotary versus self-adjusting files: a three-dimensional micro-computed tomographic study

AIM

The study was designed to quantitatively evaluate the quality of root canal preparation and root canal obturation in canals treated with either rotary or self adjusting files, using three-dimensional micro-computed tomographic (CT) analysis.

METHODOLOGY

Pair-matched root canals were instrumented with either rotary nickel-titanium files or self-adjusting files following the manufacturers' instructions. The area of the canal wall unaffected by the preparation procedure was analyzed using before and after micro-CT images. Root canal obturation was done using lateral compaction with gutta-percha and AH26 (Dentsply-DeTrey, Konstanz, Germany). Teeth were scanned a third time, and the adaptation of the filling material to the canal walls was evaluated three-dimensionally by micro-CT analysis and the area of canal wall untouched by the filling was determined. The correlation between these two parameters within each of the groups was studied using the Pearson correlation test.

RESULTS

A high percentage of unaffected root canal walls (60% +/-14%) and areas untouched by the root canal filling (45% +/- 15%) were found in canals treated with rotary files. Both parameters were significantly smaller in canals treated with self-adjusting files (17% +/- 9% and 17% +/- 11%, respectively) (p < 0.01). No correlation was found between these parameters within each of the groups.

CONCLUSION

Within the limitations of the present study, the self-adjusting files allowed better cleaning and shaping and better adaptation of the root canal filling than those allowed by rotary files.

Volumetric analysis of root fillings using spiral computed tomography: an in vitro study

AIM

To analyse volumetrically using spiral computed tomography (SCT) the efficacy of various techniques to fill root canals.

METHODOLOGY

Root canals in 40 maxillary central incisors were instrumented with K-files to size 60 and the volume of the canal measured using SCT. The teeth were divided into four groups of 10 each and root filled by lateral compaction, Thermafil, Obtura II and System B techniques, respectively. AH plus was used as sealer with all techniques. The filled volume in each canal was measured using SCT and the percentage of obturated volume (POV) was calculated. The data were statistically analysed using Kruskal-Wallis test and Mann-Whitney U-test.

RESULTS

The four groups were comparable in canal volume. The overall POV was 80.4%, 93.3%, 84.8% and 93.7% for lateral compaction, Thermafil, Obtura II and System B, respectively (P < 0.05).

CONCLUSION

The greatest POV was obtained with System B and Thermafil. Voids were seen in all root fillings.

Root Canal Treatment Using Thermoplasticized Carrier Condensation Technique

BACKGROUND

The management of pulpally and apically infected teeth has evolved into a modality of conservation with predictable degree of success. Root canal treatment often requires protracted chairside time. A new technique involving placement of thermoplasticized core carrier obturators was compared with conventional lateral condensation technique.

METHODS

A prospective, comparative, in-vivo cohort study was carried out on randomly selected 100 patients visiting a tertiary care centre from July 2005 to July 2007, for primary, non-surgical conservative management of teeth requiring root canal treatment. Two groups of fifty cases each were managed with lateral condensation and thermoplasticized core carrier obturation techniques. Outcome variables were rate of obturation and failure rates as assessed by clinical and radiological evaluation.

RESULT

The time taken in case of lateral condensation of maxillary central incisor was 17.30 ± 3.373 minutes and 28.07 ± 2.586 minutes in case of mandibular molar. In the thermoplasticized carrier condensation technique, for the central incisors it took 13.00 ± 1.376 minutes and 21.07 ± 2.463 minutes for mandibular molars. The mean rank value for time taken for obturation as per Mann Whitney U test (p < 0.01) were 27.88 for maxillary incisor and 44.73 for mandibular molar in the lateral condensation technique and 13.13 and 16.27 respectively for thermoplasticized gutta percha carrier condensation. The values were statistically significant. With 16% and 14% cases having unsatisfactory filling as evaluated by post filling radiograph, Chi square test two tailed p value was 0.6836 and there was no statistically significant difference between the two groups. An absolute failure rate of 10% was seen in lateral condensation group and 6% in thermo-plasticized carrier condensation group. Fisher exact 2-tailed p value was 0.71 and the difference in failure rate was not statistically significant.

CONCLUSION

Root canal obturation by thermoplasticized core carrier condensation technique is an effective alternative to conventional lateral condensation technique in terms of quick and successful outcome.