A Novel Transcatheter Device to Treat Calcific Aortic Valve Stenosis: An Ex Vivo Study

PURPOSE

Aortic valve stenosis (AVS) is the most common valvular disease in developed countries. Surgical or transcatheter bioprosthetic aortic valve (AV) replacement is the standard treatment for severe AVS. However, bioprostheses are prone to structural degeneration. Hence, in terms of lifetime management, there is a need for therapies that can postpone AV replacement. With the aim of fragmenting calcifications and restoring AV leaflets flexibility, a new transcatheter debridement device (TDD) exploiting ultrasound is under development. We performed an ex-vivo study on human hearts to quantify how TDD treatment affects stenotic AVs hemodynamic. Additionally, a qualitative histological analysis was performed to assess TDD's impact on AV leaflets.

METHODS

Three human hearts affected by AVS were characterized pre- and post-treatment in an ex-vivo beating heart simulator. To replicate physiological flowrates, a pulsatile pump was connected to the left ventricle, while a systemic impedance simulator connected to the aortic root and a reservoir connected to the left atrium closed the hydraulic circuit. Transvalvular pressure drop (ΔPsys), backflow volume, and effective orifice area (EOA) were evaluated. For histological analysis, AV leaflets sections were stained with Haematoxylin/Eosin and AlizarineRedS to highlight calcifications.

RESULTS

The treatment induced a reduction in ΔPsys in all tested samples, improving EOA, but caused an increase in backflow volume. Moreover, histology suggested AV leaflets integrity.

CONCLUSIONS

The TDD procedure improved AV fluid-dynamics during systole in all tested samples, without evidence of damage to tissues. This suggests TDD could be a promising option to postpone AV replacement for patients with AVS.

Impact of Open Surgical Descending Repair on Aortic Stiffness in an Ex Vivo Porcine Model

BACKGROUND

Previous studies have strongly suggested that stent-graft deployment and acute arch angulation increase aortic stiffness, the impact of surgical interposition grafting remains unclear. We investigated the impact of open surgery on aortic stiffness and compared this with stent-graft induced aortic stiffening, utilising an ex vivo model.

METHODS

Porcine thoracic aortas were connected to a mock circulatory loop. Baseline characteristics, proximal and distal flow curves (for PWV calculation), and blood pressures were recorded in a type I and III arch configuration. Subsequently, 10 cm proximal descending aorta was excised and replaced with Dacron® (IGK0018-40S). After surgery, all measurements were repeated in both arch configurations.

RESULTS

Fifteen aortas were prepared and attached to the circuit. After surgery, with both arch configurations, mean aortic PWV increased (Type I: 3.46 - 3.84 m/s (+10.7%),P < 0.001); Type III: 3.61 - 3.98 m/s (+10.4%),P = 0.001), systolic pressure remained stable (Type I: 121 - 124 mm Hg, P = 0.26; Type III: 124 - 124 mm Hg,P = 0.85), diastolic pressures decreased (Type I: 73 - 65 mm Hg,P < 0.001; Type III: 75 - 66 mm Hg,P < 0.001), and consequently mean arterial pressure decreased (Type I: 89 - 85 mm Hg,P = 0.020; Type III: 92 - 85 mm Hg,P = 0.001). The stable systolic pressure and decreased diastolic pressure, after surgery, led to an increased pulse pressure (Type I: 49 - 59 mm Hg,P < 0.001; Type III: 49 - 58 mm Hg; P < 0.001) CONCLUSIONS: Surgical interposition grafting of the proximal descending aorta increases aortic PWV, increases pulse pressure, and decreases diastolic blood pressure. These findings might be important for the long-term results of patients undergoing surgical treatment of aortic diseases.

A parametric study on pulse duplicator design and valve hemodynamics

BACKGROUND

In vitro assessment is mandatory for artificial heart valve development. This study aims to investigate the effects of pulse duplicator features on valve responsiveness, conduct a sensitivity analysis across valve prosthesis types, and contribute on the development of versatile pulse duplicator systems able to perform reliable prosthetic aortic valve assessment under physiologic hemodynamic conditions.

METHODS

A reference pulse duplicator was established based on literature. Further optimization process led to new designs that underwent a parametric study, also involving different aortic valve prostheses. These designs were evaluated on criteria such as mean pressure differential and pulse pressure (assessed from high-fidelity pressure measurements), valve opening and closing behavior, flow, and regurgitation. Finally, the resulting optimized setup was tested under five different hemodynamic settings simulating a range of physiologic and pathologic conditions.

RESULTS

The results show that both, pulse duplicator design and valve type significantly influence aortic and ventricular pressure, flow, and valve kinematic response. The optimal design comprised key features such as a compliance chamber and restrictor for diastolic pressure maintenance and narrow pulse pressure. Additionally, an atrial reservoir was included to prevent atrial-aortic interference, and a bioprosthetic valve was used in mitral position to avoid delayed valve closing effects.

CONCLUSION

This study showed that individual pulse duplicator features can have a significant effect on valve's responsiveness. The optimized versatile pulse duplicator replicated physiologic and pathologic aortic valve hemodynamic conditions, serving as a reliable characterization tool for assessing and optimizing aortic valve performance.

A Novel Transcatheter Device for the Edge-to-Edge Treatment of Tricuspid Regurgitation: A Preliminary Evaluation

Tricuspid regurgitation (TR) is the most common pathology of the tricuspid valve (TV), with significant mortality in severe cases. A well-established strategy to treat TR is represented by the clover surgical technique, which consists of stitching together the free edges of TV leaflets, producing a clover-shaped valvular orifice. Transcatheter treatments for TR constitute a valuable alternative for high-risk patients. In this work we investigated haemodynamic performances and safety of a novel device (StarTric device (STD)) aiming to perform the clover technique via percutaneous access. To assess haemodynamic performances, STD and clover were applied on porcine pathological TVs and tested. Fluid dynamic indexes of both strategies were compared to the pathological model. To evaluate device safety, forces exchanged between device and leaflets were compared to the extraction force (EF) required to STD to completely pass through the leaflet. Clover technique and STD induced a comparable TV backflow reduction (48% and 47%, respectively), with associated increase of TV flow in all tested conditions. Diastolic transvalvular pressure similarly increased indicating a reduction, though not significant, of the valvular orifice. Forces ranged from 1N to 1.71N, compared to an EF of 22.16 ± 8.6N. Force varied significantly amongst different working conditions (normotensive, mild, and severe hypertensive) for each leaflet, whilst no significative variation was found on different leaflets in the same working condition. In the adopted experimental scenario, STD demonstrated comparable efficacy to the surgical strategy in restoring TV haemodynamic. The forces acting on the leaflets following STD implantation were far lower when compared to EFs.

Type III aortic arch angulation increases aortic stiffness: Analysis from an ex vivo porcine model

Objective

The relationship among increased aortic arch angulation, aortic flow dynamics, and vessel wall stiffness remains unclear. This experimental ex vivo study investigated how increased aortic arch angulation affects aortic stiffness and stent-graft induced aortic stiffening, assessed by pulse wave velocity (PWV).

Methods

Porcine thoracic aortas were connected to a circulatory mock loop in a Type I and Type III aortic arch configuration. Baseline characteristics and blood pressures were measured. Proximal and distal flow curves were acquired to calculate PWV in both arch configurations. After that, a thoracic stent-graft (VAMF2626C100TU) was deployed in aortas with adequate proximal landing zone diameters to reach 10% t0 20% oversizing. Acquisitions were repeated for both arch configurations after stent-graft deployment.

Results

Twenty-four aortas were harvested, surgically prepared, and mounted. Cardiac output was kept constant for both arch configurations (Type I: 4.74 ± 0.40 and Type III: 4.72 ± 0.38 L/minute; P = .703). Compared with a Type I arch, aortic PWV increased significantly in the Type III arch (3.53 ± 0.40 vs 3.83 ± 0.40 m/second; P < .001), as well as blood pressures. A stent-graft was deployed in 15 aortas. After deployment, Type I arch PWV increased (3.55 ± 0.39 vs 3.81 ± 0.44 m/second; P < .001) and Type III arch PWV increased although not significantly (3.86 ± 0.42 vs 4.03 ± 0.46 m/second; P = .094). Type III arch PWV resulted the highest and significantly higher compared with the Type I arch after stent-graft deployment (3.81 ± 0.44 vs 4.03 ± 0.46 m/second; P = .023).

Conclusions

Increased aortic arch angulation-as in a Type III arch-is associated with higher aortic PWV and blood pressures and this may negatively influence cardiovascular health.

Coronary Perfusion After Valve-in-Valve Transcatheter Aortic Valve Implantation in Small Aortic Root: In Vitro Experimental Assessment

Coronary flow obstruction following transcatheter aortic valve-in-valve implantation (VIV-TAVI) is associated with a high mortality risk. The aim of this work was to quantify the coronary perfusion after VIV-TAVI in a high-risk aortic root anatomy. 3D printed models of small aortic root were used to simulate the implantation of a TAVI prosthesis (Portico 23) into surgical prostheses (Trifecta 19 and 21). The aortic root models were tested in a pulsatile in vitro bench setup with a coronary perfusion simulator. The tests were performed at baseline and post-VIV-TAVI procedure in aligned and misaligned commissural configurations under simulated hemodynamic rest and exercise conditions. The experimental design provided highly controllable and repeatable flow and pressure conditions. The left and right coronary mean flow did not differ significantly at pre- and post-VIV-TAVI procedure in any tested configurations. The commissural misalignment did not induce any significant alterations to the coronary flow. High-risk aortic root anatomy did not trigger coronary ostia obstruction or coronary flow alteration after transcatheter aortic valve implantation in a surgical bioprosthesis as shown from in-vitro flow loop tests.

Impact of thoracic endovascular aortic repair on aortic biomechanics: Integration of in silico and ex vivo analysis using porcine model

Thoracic endovascular aortic repair (TEVAR) is widespread in clinical practice for treating aortic diseases but it has relevant systemic complications, such as increase of the cardiac workload due to post-TEVAR aortic stiffening, and local issues such as re-entry tears due to the tissue damage caused by endograft interaction. The present study aims to elucidate these aortic biomechanical mechanisms by coupling ex vivo and in silico analysis. By ex vivo tests, the pulse wave velocity before and after TEVAR is measured. Uni-axial tensile tests are performed to measure regional mechanical response of tissue samples, supplied as input data for the in silico analysis. Numerical analysis is finally performed to compute the wall stress induced by the stent-graft deployment and the arterial pressurization. The ex vivo results highlight an increase of baseline PWV by a mean .78 m/s or 12% after TEVAR with a 100 mm stent-graft (p <.013). In the in silico analysis, the average von Mises stress in the landing zone increases of about 15% and 20% using, respectively stent-graft with radial oversizing of 10% and 20%. This work shows the effectiveness of integrated framework to analyze the biomechanical post TEVAR mechanisms. Moreover, the obtained results quantify the effect of prosthesis selection on the stiffening of the aorta after TEVAR and on the local increase of the aortic wall stress that is proportional to the stent-graft oversizing.

Comparison of Two Generations of Thoracic Aortic Stent Grafts and Their Impact on Aortic Stiffness in an Ex Vivo Porcine Model

Objective

Little is known about the cardiovascular changes after TEVAR and regarding the impact on aortic stiffness for different stent graft generations specifically, following changes in device design. The present study evaluated the stent graft induced aortic stiffening of two generations of the Valiant thoracic aortic stent graft.

Methods

This was an ex vivo porcine investigation using an experimental mock circulatory loop. Thoracic aortas of young healthy pigs were harvested and connected to the mock circulatory loop. At a 60 bpm heart rate and stable mean arterial pressure, baseline aortic characteristics were obtained. Pulse wave velocity (PWV) was calculated before and after stent graft deployment. Paired and independent sample t tests or their non-parametric alternatives were performed to test for differences where appropriate.

Results

Twenty porcine thoracic aortas were divided into two equal subgroups, in which a Valiant Captivia or a Valiant Navion stent graft was deployed. Both stent grafts were similar in diameter and length. Baseline aortic characteristics did not differ between the subgroups. Mean arterial pressure values did not change after either stent graft, while pulse pressures increased statistically significantly after Captivia (mean 44 ± 10 mmHg to 51 ± 13 mmHg, p = .002) but not after Navion. Mean baseline PWV increased after both Captivia (4.4 ± 0.6 m/s to 4.8 ± 0.7 m/s, p = .007) and Navion (4.6 ± 0.7 m/s to 4.9 ± 0.7 m/s, p = .002). There was no statistically significant difference in the mean percentage increase in PWV for either subgroup (8 ± 4% vs. 6 ± 4%, p = .25).

Conclusion

These experimental findings showed no statistically significant difference in the percentage increase of aortic PWV after either stent graft generation and confirm that TEVAR increases aortic PWV. As a surrogate for aortic stiffness, this calls for further improvements in future thoracic aortic stent graft designs regarding device compliance.

Design, simulation, and fabrication of a three-dimensional printed pump mimicking the left ventricle motion

The development of accurate replicas of the circulatory and cardiac system is fundamental for a deeper understanding of cardiovascular diseases and the testing of new devices. Although numerous works concerning mock circulatory loops are present in the current state of the art, still some limitations are present. In particular, a pumping system able to reproduce the left ventricle motion and completely compatible with the magnetic resonance environment to permit the four-dimensional flow monitoring is still missing. The aim of this work was to evaluate the feasibility of an actuator suitable for cardiovascular mock circuits. Particular attention was given to the ability to mimic the left ventricle dynamics including both compression and twisting with the magnetic resonance compatibility. In our study, a left ventricle model to be actuated through vacuum was designed. The realization of the system was evaluated with finite element analysis of different design solutions. After the in silico evaluation phase, the most suitable design in terms of physiological values reproduction was fabricated through three-dimensional printing for in vitro validation. A pneumatic experimental setup was developed to evaluate the pump performances in terms of actuation, in particular ventricle radial and longitudinal displacement, twist rotation, and ejection fraction. The study demonstrated the feasibility of a custom pneumatic pump for mock circulatory loops able to reproduce the physiological ventricle movement and completely suitable for the magnetic resonance environment.

A compliant aortic model for in vitro simulations: Design and manufacturing process

We design and manufacture a silicone model of the human aorta, able to mimic both the geometrical and the mechanical properties of physiological individuals, with a specific focus on reproducing the compliance. In fact, while the models available in the literature exhibit an unrealistic compliant behavior, though they are detailed from the geometrical viewpoint, here the goal is to provide an accurate compliant tool for in vitro testing the devices that interface with the vascular system. A parametric design of the aortic model is obtained based on the available literature data, and the model is manufactured with a specific silicone mixture using rapid prototyping and molding techniques. The manufactured prototype has been tested by means of computed tomography scans for evaluating the matching of the mechanical properties with the desired ones. Results show a high degree of adherence between the imposed and the measured compliance values for each main aortic section. Thus, our work proves the feasibility of the approach, and the possibility to manufacture compliant models that reproduce the mechanical behavior of the aorta for in vitro studies.

Changes in aortic pulse wave velocity of four thoracic aortic stent grafts in an ex vivo porcine model

Objectives

Thoracic endovascular aortic repair (TEVAR) has been shown to lead to increased aortic stiffness. The aim of this study was to investigate the effect of stent graft type and stent graft length on aortic stiffness in a controlled, experimental setting.

Methods

Twenty porcine thoracic aortas were connected to a pulsatile mock loop system. Intraluminal pressure was recorded at two sites in order to measure pulse wave velocity (PWV) for each aorta: before stent graft deployment (t₁); after deployment of a 100-mm long stent graft (t₂); and after distal extension through deployment of a second 100-mm long stent graft (t₃). Four different types of stent grafts (Conformable Gore^® TAG^® Device, Bolton Relay^® Device, Cook Zenith Alpha^™, and Medtronic Valiant^®) were evaluated.

Results

For the total cohort of 20 aortas, PWV increased by a mean 0.6 m/s or 8.9% of baseline PWV after deployment of a 100-mm proximal stent graft (P<0.001), and by a mean 1.4 m/s or 23.0% of baseline PWV after distal extension of the stent graft (P<0.001). Univariable regression analysis showed a significant correlation between aortic PWV and extent of stent graft coverage, (P<0.001), but no significant effect of baseline aortic length, baseline aortic PWV, or stent graft type on the percentual increase in PWV at t₂ or at t₃.

Conclusions

In this experimental set-up, aortic stiffness increased significantly after stent graft deployment with each of the four types of stent graft, with the increase in aortic stiffness depending on the extent of stent graft coverage.

A Novel Insight into the Role of Entry Tears in Type B Aortic Dissection: Pressure Measurements in an in Vitro Model

Introduction

Predicting aortic growth in acute type B dissection is fundamental in planning interventions. Several factors are considered to be growth predictors in the literature and, among them, size and location of entry tears have been recognized to particularly influence the false lumen pressure. In this study, we develop an in vitro setting to analyze the actual impact of size and location of the entry tears on false lumen pressure, in the absence of other confounding factors such as the deformability of the aortic wall.

Methods

We formalize some indexes that synthetically describe the false lumen pressure with respect to the true lumen pressure. Then, we experimentally derive their values in several configurations of the in vitro setting, and we look for trends in the indexes with respect to the size and location of entry tears.

Results:

Results show that the tears have a relevant impact on the false lumen pressure, but that their size and location alone are not enough to explain the phenomena observed in vivo.

Conclusions

To predict the behavior of acute type B dissection, we therefore recommend not limiting to size and location, as many effects may derive from the interactions between these parameters and other patient characteristics.

In vitro assessment of mitral valve function in cyclically pressurized porcine hearts

Recent approaches to the in vitro experimental study of cardiac fluid mechanics involve the use of whole biological structures to investigate in the lab novel therapeutic approaches for the treatment of heart pathologies. To enhance reliability and repeatability, the influence of the actuation strategy of the experimental apparatuses on the biomechanics of biological structures needs to be assessed. Using echography and intracardiac high-speed imaging, we compared the mitral valve (MV) anatomo-functional features (coaptation areas/lengths, papillary muscles-valvular plane distances) in two passive-beating-heart mock loops with internal (IPML) or external (EPML) pressurization of the ventricular chamber. Both apparatuses showed fluid dynamic conditions that closely resembled the physiology. The MVs analyzed in the EPML presented coaptation areas and lengths that were systematically higher, and exhibited greater variability from early-to peak-systole, as compared to those in the IPML. Moreover, in the EPML, the MV leaflets exhibited a convexity with high curvature toward the atrium. With the IPML, MV coaptation lengths ranged similar to available clinical data and the papillary muscles-valve plane distances were more stable throughout systole. In conclusion, both the apparatuses allow for reproducing in vitro the left heart hemodynamics, in terms of flow rates and pressures, with proper mitral valve continence. Results suggest that the IPML is more suitable for replicating the physiological MV functioning, while the EPML may have more potential as a model for the study of MV pathologies.

Fluid dynamic characterization of a polymeric heart valve prototype (Poli-Valve) tested under continuous and pulsatile flow conditions

PURPOSE

Only mechanical and biological heart valve prostheses are currently commercially available. The former show longer durability but require anticoagulant therapy; the latter display better fluid dynamic behavior but do not have adequate durability. New Polymeric Heart Valves (PHVs) could potentially combine the hemodynamic properties of biological valves with the durability of mechanical valves. This work presents a hydrodynamic evaluation of 2 groups of newly developed supra-annular, trileaflet prosthetic heart valves made from styrenic block copolymers (SBC): Poli-Valves.

METHODS

2 types of Poli-Valves made of SBC and differing in polystyrene fraction content were tested under continuous and pulsatile flow conditions as prescribed by ISO 5840 Standard. A pulse duplicator designed ad hoc allowed the valve prototypes to be tested at different flow rates and frequencies. Pressure and flow were recorded; pressure drops, effective orifice area (EOA), and regurgitant volume were computed to assess the behavior of the valve.

RESULTS

Both types of Poli-Valves met the minimum requirements in terms of regurgitation and EOA as specified by the ISO 5840 Standard. Results were compared with 5 mechanical heart valves (MHVs) and 5 tissue heart valves (THVs), currently available on the market.

CONCLUSIONS

Based on these results, PHVs based on styrenic block copolymers, as are Poli-Valves, can be considered a promising alternative for heart valve replacement in the near future.

Effect of the Pulsatile Extracorporeal Membrane Oxygenation on Hemodynamic Energy and Systemic Microcirculation in a Piglet Model of Acute Cardiac Failure

The objective of this study was to compare the effects of pulsatile and nonpulsatile extracorporeal membrane oxygenation (ECMO) on hemodynamic energy and systemic microcirculation in an acute cardiac failure model in piglets. Fourteen piglets with a mean body weight of 6.08 ± 0.86 kg were divided into pulsatile (N = 7) and nonpulsatile (N = 7) ECMO groups. The experimental ECMO circuit consisted of a centrifugal pump, a membrane oxygenator, and a pneumatic pulsatile flow generator system developed in-house. Nonpulsatile ECMO was initiated at a flow rate of 140 mL/kg/min for the first 30 min with normal heart beating, with rectal temperature maintained at 36°C. Ventricular fibrillation was then induced with a 3.5-V alternating current to generate a cardiac dysfunction model. Using this model, we collected the data on pulsatile and nonpulsatile groups. The piglets were weaned off ECMO at the end of the experiment (180 min after ECMO was initiated). The animals did not receive blood transfusions, inotropic drugs, or vasoactive drugs. Blood samples were collected to measure hemoglobin, methemoglobin, blood gases, electrolytes, and lactic acid levels. Hemodynamic energy was calculated using the Shepard's energy equivalent pressure. Near-infrared spectroscopy was used to monitor brain and kidney perfusion. The pulsatile ECMO group had a higher atrial pressure (systolic and mean), and significantly higher regional saturation at the brain level, than the nonpulsatile group (for both, P < 0.05). Additionally, the pulsatile ECMO group had higher methemoglobin levels within the normal range than the nonpulsatile group. Our study demonstrated that pulsatile ECMO produces significantly higher hemodynamic energy and improves systemic microcirculation, compared with nonpulsatile ECMO in acute cardiac failure.

A Newly Developed Tri-Leaflet Polymeric Heart Valve Prosthesis

The potential of polymeric heart valves (PHV) prostheses is to combine the hemodynamic performances of biological valves with the durability of mechanical valves. The aim of this work is to design and develop a new tri-leaflet prosthetic heart valve (HV) made from styrenic block copolymers. A computational finite element model was implemented to optimize the thickness of the leaflets, to improve PHV mechanical and hydrodynamic performances. Based on the model outcomes, 8 prototypes of the designed valve were produced and tested in vitro under continuous and pulsatile flow conditions, as prescribed by ISO 5840 Standard. A specially designed pulse duplicator allowed testing the PHVs at different flow rates and frequency conditions. All the PHVs met the requirements specified in ISO 5840 Standard in terms of both regurgitation and effective orifice area (EOA), demonstrating their potential as HV prostheses.

Inertance estimation in a lumped-parameter hydraulic simulator of human circulation

Pulsatile mock loop systems are largely used to investigate the cardiovascular system in vitro. They consist of a pump, which replicates the heart, coupled with a lumped-parameter hydraulic afterload, which simulates vasculature. An accurate dimensioning of components is required for a reliable mimicking of the physiopathological behavior of the system. However, it is not possible to create a component for the afterload inertance, and inertance contributions are present in the entire circuit. Hence, in the literature, inertance is neglected or qualitatively evaluated. In this paper, we propose two quantitative methods (Maximum-likelihood estimation (MLE) and Bayesian estimation) for estimating afterload inertance based on observed pressure and flow waveforms. These methods are also applied to a real mock loop system. Results show that the system has an inertance comparable with the literature reference value of the entire systemic circulation, and that the expected variations over inlet average flow and pulse frequency are in general confirmed. Comparing the methods, the Bayesian approach results in higher and more stable estimations than the classical MLE.

Computational Models of Aortic Coarctation in Hypoplastic Left Heart Syndrome: Considerations on Validation of a Detailed 3D model

Background

Reliability of computational models for cardiovascular investigations strongly depends on their validation against physical data. This study aims to experimentally validate a computational model of complex congenital heart disease (i.e., surgically palliated hypoplastic left heart syndrome with aortic coarctation) thus demonstrating that hemodynamic information can be reliably extrapolated from the model for clinically meaningful investigations.

Materials and methods

A patient-specific aortic arch model was tested in a mock circulatory system and the same flow conditions were re-created in silico, by setting an appropriate lumped parameter network (LPN) attached to the same three-dimensional (3D) aortic model (i.e., multi-scale approach). The model included a modified Blalock-Taussig shunt and coarctation of the aorta. Different flow regimes were tested as well as the impact of uncertainty in viscosity.

Results

Computational flow and pressure results were in good agreement with the experimental signals, both qualitatively, in terms of the shape of the waveforms, and quantitatively (mean aortic pressure 62.3 vs. 65.1 mmHg, 4.8% difference; mean aortic flow 28.0 vs. 28.4% inlet flow, 1.4% difference; coarctation pressure drop 30.0 vs. 33.5 mmHg, 10.4% difference), proving the reliability of the numerical approach. It was observed that substantial changes in fluid viscosity or using a turbulent model in the numerical simulations did not significantly affect flows and pressures of the investigated physiology. Results highlighted how the non-linear fluid dynamic phenomena occurring in vitro must be properly described to ensure satisfactory agreement.

Conclusions

This study presents methodological considerations for using experimental data to preliminarily set up a computational model, and then simulate a complex congenital physiology using a multi-scale approach.

In vitro hemodynamics and valve imaging in passive beating hearts

Due to their high complexity, surgical approaches to valve repair may benefit from the use of in vitro simulators both for training and for the investigation of those measures which can lead to better clinical results. In vitro tests are intrinsically more effective when all the anatomical substructures of the valvular complexes are preserved. In this work, a mock apparatus able to house an entire explanted porcine heart and subject it to pulsatile fluid-dynamic conditions was developed, in order to enable the hemodynamic analysis of simulated surgical procedures and the imaging of the valvular structures. The mock loop's hydrodynamic design was based on an ad-hoc defined lumped-parameter model. The left ventricle of an entire swine heart was dynamically pressurized by an external computer-controlled pulse duplicator. The ascending aorta was connected to a hydraulic circuit which simulated the input impedance of the systemic circulation; a reservoir passively filled the left atrium. Accesses for endoscopic imaging were located in the apex of the left ventricle and in the aortic root. The experimental pressure and flow tracings were comparable with the typical in vivo curves; a mean flow of 3.5±0.1l pm and a mean arterial pressure of 101±2 mmHg was obtained. High-quality echographic and endoscopic video recordings demonstrated the system's excellent potential in the observation of the cardiac structures dynamics. The proposed mock loop represents a suitable in vitro system for the testing of minimally-invasive cardiovascular devices and surgical procedures for heart valve repair.

A pulsatile simulator for the in vitro analysis of the mitral valve with tri-axial papillary muscle displacement

PURPOSE

We developed a new pulsatile hydrodynamic simulator for the in vitro testing of mitral valve (MV) samples. The required specifications included a 3D positioning system for the papillary muscles (PMs) that is accurate and simple to manage; measurement of the force exerted by the chordae tendineae on the PMs; and the possibility to visually inspect the MV for kinematic analysis.

METHODS

An atrial/ventricular chamber system was developed. The ventricular chamber housed a tri-axial actuator system that was aligned to a morphometric Cartesian frame, allowing for PM positioning even while tests are running. Each PM holder had an embedded load cell for force measurement. The atrial chamber was designed so as to permit MV visual inspection, maintaining a non-disturbed flow at the sample inlet. The setup was subjected to trials with fresh porcine MVs. Flow and pressure difference across the MVs and PM forces were measured in different MV configurations, with different PM spatial dislocations. High speed video recordings were acquired.

RESULTS

The positioning accuracy was assessed. Tests with MVs showed good usability, even by the non-engineering personnel. The effects of PM displacement on valve function (valve competence and PM forces) was consistent with previously published data, thus confirming the general soundness of the design principles.

CONCLUSIONS

The developed simulator is a promising instrument for performing MV in vitro tests in a precise, well-repeatable manner. The ability to completely adjust the PM position while a test is running boosts the simulator's potential for detailed investigations of the pathological and surgically treated MV.

Beat-rate Dependent Mitral Flow Patterns for in Vitro Hemodynamic Applications

The conservative surgery approach for restoring the functionality of heart valves has predominated during the last two decades, particularly for the mitral valve. In vitro pulsatile testing is a key methodology for the investigation of heart valve hemodynamics, and particularly for the ideation, validation and optimization of novel techniques in heart valve surgery. Traditionally, however, pulsatile mock loops have been developed for the study of aortic valve substitutes, and scarce attention has been paid in replicating the mitral flow patterns with due hemodynamic fidelity. In this work we provide detailed analytical expressions to produce beat-rate dependent, physiologic-like mitral flow patterns for in vitro applications. The approach we propose is based on a biomechanical analysis of the factors which govern hemodynamic changes in the mitral flow pattern, namely in terms of E and A wave contours and E/A peaks ratio, when switching from rest to mild exercise conditions. The patterns from the model we obtained were in good agreement with clinical literature data in terms of i) gradual superimposition of the E and A wave, which yielded a single peak at 96 bpm; ii) decrease in the E/A ratio with increasing heart rate; iii) amount of flow delivered by each of the two waves. The proposed method provides a physiologically representative, beat-rate dependent analytical expression of the mitral flow pattern, which can be used in in vitro hydrodynamic investigations to accurately replicate the changes that the flow waves experience when the heart rate shifts from rest to mild exercise conditions.