Prosthetic Requirements for Immediate Implant Loading: A Review

Gradient-induced vibrations and motion-induced Lenz effects on conductive nonmagnetic orthopedic implants in MRI

PURPOSE

To quantify the extent of gradient-induced vibrations, and the magnitude of motion-induced displacement forces ("Lenz effect"), in conductive nonmagnetic orthopedic prostheses.

METHODS

The investigation is carried out through numerical simulations, for a 3 T scanner. For gradient-induced torques and vibrations, a knee and a shoulder implant are considered, at dB/dt equal to 42 T/s (rms). For motion-induced forces associated with the Lenz effect, a knee and a hip implant are studied, considering a patient who translates on the examination couch, or walks next to it.

RESULTS

Gradient-induced torques may be within the same order of magnitude as the worst case gravitational torque defined in the ASTM standards. However, for all investigated cases, they result to be lower. In vacuum, the extent of the corresponding vibration reduces with frequency. At the lowest investigated frequency (270 Hz), it keeps below 25 μm. For an implant partially embedded in bone, the extent of the vibration increases with frequency. Nevertheless, the displacement is far lower than the worst case observed in vacuum (negligible in contact with the bone; ˜1 μm or less where the implant emerges from the bone). The Lenz effect induced by the motion of the patient through the stationary magnetic field produces forces on the order of a few millinewtons (i.e., at least two orders of magnitude lower than the implant weight).

CONCLUSION

Comparing the results with mechanical loads caused by ordinary activities of daily living, and with the levels of tolerable micromotions, a good safety margin is confirmed.

Full arch immediate occlusal loading using site specific implants: A clinical series of 10 patients (13 arches)

PURPOSE

Osseointegration of dental endosseous implants has proven to be effective, predictable, and clinically successful. Unloaded healing protocols were originally used in treating edentulous patients. Full arch immediate occlusal loading protocols have been shown to be as effective as unloaded healing protocols. This paper reports on the results, benefits, and limitations of one specific immediate loading protocol using site specific implants for fresh extraction and healed extraction sites.

MATERIALS AND METHODS

Ten consecutive patients [{13 arches} (age range: 64-81 years; average: 70.1) (4 males/6 females) were treated by the first 2 authors in private practice settings. Hopeless teeth were scheduled for extraction with immediate implant placement and immediate loading with insertion of full arch, screw-retained, acrylic resin interim prostheses within 24 hours. Implants were also placed into healed edentulous ridges. Insertion torque values for each implant were recorded. Interim prostheses were removed after at least 3 months of healing. Implants were reverse torque tested (35 Ncm) and evaluated for macroscopic mobility. Definitive full arch prostheses were made. Patients were followed for 21 to 48 months postimplant surgery. Panoramic radiographs were taken immediately postimplant placement and 1 year postoperative.

RESULTS

Thirteen arches were treated; 11 ultrawide diameter implants were placed into molar sockets, 26 inverted body-shift implants were placed into anterior sockets; 25 standard diameter, tapered implants were placed into edentulous sites; 2 zygomatic implants were placed in one patient. The total number of implants placed was 64 (4 preexisting implants were also used and not included in this study). The minimum implant insertion torque value was 20 Ncm. After 12 to 18 months of function (average 14 months), the implant and prosthetic survival rates were 100%. Eight patients were restored with definitive zirconia or acrylic resin hybrid fixed prostheses. Two patients were restored with bar titanium frameworks and removable overdenture prostheses. No prosthetic complications were reported for the definitive prostheses.

CONCLUSIONS

The results of this clinical series with site specific implants and immediate full arch occlusal loading in treating edentulous patients resulted in 100% clinical implant and prosthetic survival rates. According to this study, this protocol can be used with high levels of anticipated success.

The effect of loading time on marginal bone change of implants immediately placed after extraction: a retrospective study

BACKGROUND

The purpose of this study is to compare and analyze the treatment outcomes between two groups which are both immediately placed implant cases, one is immediate loading, and the other is conventional loading group.

METHODS

Medical records of the patients who underwent implant treatment which were immediately placed after tooth extraction were analyzed. Demographic data were collected and by using periapical or panoramic radiographic image, marginal bone level and distant crestal bone level were measured. Marginal bone change over time was analyzed and compared between immediate loading group and conventional loading group.

RESULTS

A total of 71 patients, 112 immediately placed implants after tooth extraction were initially involved. Measuring was done with implants which had not failed (81). 10 implants were had failed and removed. The others were excluded because of follow-up loss, absence of radiographic image, etc. Demographic data were collected, and measured values were averaged at each follow-up and showed in linear graphs.

CONCLUSIONS

In case of immediate implantation of dental implant after extraction, loading time could affect marginal bone level or biological width of the implant. Immediate loading group showed 0.92 mm (mean value) more bone loss compared to conventional loading group at bone-implant contact points 24 months after implantation. At distant crestal points, there was no noticeable difference in bone change pattern between two groups.

Immediate Restoration of Single-Piece Zirconia Implants: A Prospective Case Series-Long-Term Results after 11 Years of Clinical Function

OBJECTIVES

The aim of this prospective case series was to evaluate single-piece zirconia implants restored with lithium disilicate CAD/CAM crowns through a long-term follow-up.

METHODS

In this trial, 20 one-piece zirconia implants were placed in 20 patients. Implants were restored (i) immediately with lithium disilicate CAD/CAM provisionals, and (ii) permanently four months after surgery. Patients were followed for 11 years. Clinical parameters and radiological measurements of the zirconia implants were assessed. For the statistical analysis, paired t-test was applied.

RESULTS

Four implants were counted as implant failure due to the loss of implant stability, resulting in a Kaplan-Meier survival rate of 80% up to 11 years. The mean bleeding on probing values were 19.1% (SD ± 13.1) and 18.2% (SD ± 17.6) 96 and 11 years after implant placement, respectively. The plaque index revealed a significant decrease over time (p < 0.001) with a value between 25.9% (SD ± 5.7) and 12.6% (SD ± 10.0) at baseline and 11-years follow-up respectively. The marginal bone level revealed a significant decrease 4, 8, and 11 years after implant insertion (p = 0.001, p = 0.019, and p = 0.027, respectively).

CONCLUSIONS

Immediately loaded zirconia single-piece implants showed a suitable success rate in clinical and radiographic outcomes.

The limit of tolerable micromotion for implant osseointegration: a systematic review

Much research effort is being invested into the development of porous biomaterials that enhance implant osseointegration. Large micromotions at the bone-implant interface impair this osseointegration process, resulting in fibrous capsule formation and implant loosening. This systematic review compiled all the in vivo evidence available to establish if there is a universal limit of tolerable micromotion for implant osseointegration. The protocol was registered with the International Prospective Register for Systematic Reviews (ID: CRD42020196686). Pubmed, Scopus and Web of Knowledge databases were searched for studies containing terms relating to micromotion and osseointegration. The mean value of micromotion for implants that osseointegrated was 32% of the mean value for those that did not (112 ± 176 µm versus 349 ± 231 µm, p < 0.001). However, there was a large overlap in the data ranges with no universal limit apparent. Rather, many factors were found to combine to affect the overall outcome including loading time, the type of implant and the material being used. The tables provided in this review summarise these factors and will aid investigators in identifying the most relevant micromotion values for their biomaterial and implant development research.

Differences in treatment outcomes of definitive fixed implant-supported restorations with or without an interim restoration: A systematic review

STATEMENT OF PROBLEM

Guidance to determine whether providing an interim implant-supported restoration is beneficial is lacking.

PURPOSE

The purpose of this systematic review was to answer the following focused question: "Does the use of interim fixed implant prostheses before placement of a definitive fixed implant-supported prostheses impact esthetics, peri-implant health, and osseointegration in partially dentate adults?"

MATERIAL AND METHODS

A search of electronic databases (Medline and Embase) and the nonpeer-reviewed literature for randomized controlled trials, systematic reviews, and cohort studies in the English language was conducted.

RESULTS

Two studies met the eligibility criteria. Heterogeneity of the study methodologies and outcome measures did not allow for meta-analysis. Use of interim implant-supported restorations may improve the esthetic outcome. Occlusal loading of definitive implant-supported prosthesis without the use of an interim restoration may decrease chair time and the number of patient visits.

CONCLUSIONS

The systematic review has found insufficient evidence to support or refute the practice of providing an interim restoration before delivering an implant-supported prosthesis.

The Effect of Different Cleaning Protocols of Polymer-Based Prosthetic Materials on the Behavior of Human Gingival Fibroblasts

Dental implant abutment and prosthetic materials, their surface treatment, and cleaning modalities are important factors for the formation of a peri-implant soft tissue seal and long-term stability of bone around the implant. This study aimed to investigate the influence of a polymeric material surface cleaning method on the surface roughness, water contact angle, and human gingival fibroblasts (HGF) proliferation. Polymeric materials tested: two types of milled polymethylmethacrylate (PMMA-Ker and PMMA-Bre), three-dimensionally (3D) printed polymethylmethacrylate (PMMA-3D), polyetheretherketone (PEEK), and polyetherketoneketone (PEKK). Titanium (Ti) and zirconia oxide ceramics (ZrO-HT) were used as positive controls. A conventional surface cleaning protocol (CCP) was compared to a multi-step research cleaning method (RCP). Application of the RCP method allowed to reduce S_a values in all groups from 0.14-0.28 µm to 0.08-0.17 µm (p < 0.05 in PMMA-Ker and PEEK groups). Moreover, the water contact angle increased in all groups from 74-91° to 83-101° (p < 0.05 in the PEKK group), except ZrO-HT-it was reduced from 98.7 ± 4.5° to 69.9 ± 6.4° (p < 0.05). CCP resulted in higher variability of HGF viability after 48 and 72 h. RCP application led to higher HGF viability in PMMA-3D and PEKK groups after 48 h, but lower for the PMMA-Ker group (p < 0.05). After 72 h, no significant differences in HGF viability between both cleaning methods were observed. It can be concluded that the cleaning method of the polymeric materials affected surface roughness, contact angle, and HGF viability at 48 h.

Immediate versus delayed temporization at posterior single implant sites: A randomized controlled trial

AIMS

We conducted a randomized controlled trial to assess the clinical outcomes of two loading protocols involving either immediate or delayed prosthetic temporization of single implants placed at posterior, healed sites.

MATERIALS AND METHODS

Forty-nine patients in need of single implants at premolar or molar sites were randomized to receive a temporary crown either immediately after implant placement or 3 months later. Randomization was stratified by sex, implant location (premolar/molar) and arch (maxilla/mandible). Final implant screw-retained zirconia crowns with angulated screw channels were delivered at 5 months after surgery. Radiographic bone levels (primary outcome), peri-implant mucosal margin levels and peri-implant probing depths were recorded at baseline, 6 and 12 months after surgery.

RESULTS

Both treatment arms showed similar patterns of soft tissue and bone re-modelling from the implant platform over 12 months [mean bone level change 1.6 mm (SD 1.0 mm) in the delayed, and 1.2 mm (SD 1.3 mm) in the immediate temporization group], with the majority of changes occurring within the first 6 months.

CONCLUSIONS

Immediate or delayed temporization of single implants placed at posterior healed sites resulted in largely similar 1-year outcomes with respect to peri-implant bone levels and soft tissue changes.

Immediate occlusal vs nonocclusal loading of implants: A randomized prospective clinical pilot study and patient centered outcome after 36 months

Background

Immediate provisionalization reduces chair time and improves patient comfort.

Purpose

To analyze immediate functional loading vs nonfunctional loading with restorations in the posterior mandible for marginal bone defects, implant success/survival, and patient satisfaction.

Materials and Methods

A randomized controlled clinical trial was designed to assess these parameters based on 20 adult patients who underwent implant surgery, followed by immediate delivery of screw‐retained or cemented single or splinted restorations in full occlusal contact or in infraocclusion (test and control group). A questionnaire with visual analog scales was used to assess patient satisfaction.

Results

Following 36‐month data were evaluable for 9 patients (21 implants) in the study group (immediate functional loading) and for 10 patients (31 implants) in the control group (immediate nonfunctional loading). One implant in the control group was lost, hence the overall implant survival and success rate was 98.2%. Marginal bone defects were consistent with previous studies and comparable in both groups. Periotest values did not significantly change from baseline and the 12‐month follow‐up (Friedmann test). Patient satisfaction was high and did not involve any significant intergroup differences (Mann‐Whitney U‐test).

Conclusions

Both types of immediate provisional restorations are viable in selected patients. Larger randomized controlled trials are needed to establish immediate functional loading as a standard treatment for partially edentulous jaws.

Scanning Electron Microscope (SEM) Evaluation of the Interface between a Nanostructured Calcium-Incorporated Dental Implant Surface and the Human Bone

Purpose. The aim of this scanning electron microscope (SEM) study was to investigate the interface between the bone and a novel nanostructured calcium-incorporated dental implant surface in humans. Methods. A dental implant (Anyridge^®, Megagen Implant Co., Gyeongbuk, South Korea) with a nanostructured calcium-incorporated surface (Xpeed^®, Megagen Implant Co., Gyeongbuk, South Korea), which had been placed a month earlier in a fully healed site of the posterior maxilla (#14) of a 48-year-old female patient, and which had been subjected to immediate functional loading, was removed after a traumatic injury. Despite the violent trauma that caused mobilization of the fixture, its surface appeared to be covered by a firmly attached, intact tissue; therefore, it was subjected to SEM examination. The implant surface of an unused nanostructured calcium-incorporated implant was also observed under SEM, as control. Results. The surface of the unused implant showed a highly-structured texture, carved by irregular, multi-scale hollows reminiscent of a fractal structure. It appeared perfectly clean and devoid of any contamination. The human specimen showed trabecular bone firmly anchored to the implant surface, bridging the screw threads and filling the spaces among them. Conclusions. Within the limits of this human histological report, the sample analyzed showed that the nanostructured calcium-incorporated surface was covered by new bone, one month after placement in the posterior maxilla, under an immediate functional loading protocol.

Bimaxillary simultaneous immediate loading of full-arch restorations: A case series

Aim

To describe a bimaxillary simultaneous immediate loading protocol with full-arch implant-supported fixed prostheses.

Material and Methods

A prospective case series of 8 patients who required full-arch rehabilitation was conducted. The main inclusion criteria were patients with teeth that required extraction. At least 1 molar per arch was temporarily employed to stabilize the surgical template and the provisional prosthesis during intraoral relining.

Results

Two upper implants failed in 1 patient. Structural fracture was registered in 3 patients, around 3 months after loading. All of them had bruxism. Three esthetic complications were registered: midline deviation, canting of the oclusal plane and color mismatch.

Conclusions

Although this protocol achieves optimal results, some mechanical complications were encountered. The fracture of the provisional prosthesis is a relatively common mechanical complication but does not seem to jeopardize the final treatment result.

Key words:Implant-supported full-arch, provisional prosthesis fracture, bimaxillary simultaneous rehabilitation, conical abutments.

Immediate Loading of Tapered Implants Placed in Postextraction Sockets and Healed Sites

OBJECTIVE

The aim of the present study was to compare the survival, stability, and complications of immediately loaded implants placed in postextraction sockets and healed sites.

METHODS

Over a 2-year period, all patients presenting with partial or complete edentulism of the maxilla and/or mandible (healed site group, at least 4 months of healing after tooth extraction) or in need of replacement of nonrecoverable failing teeth (postextraction group) were considered for inclusion in this study. Tapered implants featuring a nanostructured calcium-incorporated surface were placed and loaded immediately. The prosthetic restorations comprised single crowns, fixed partial dentures, and fixed full arches. Primary outcomes were implant survival, stability, and complications. Implant stability was assessed at placement and at each follow-up evaluation (1 week, 3 months, and 1 year after placement): implants with an insertion torque (IT) <45 N·cm and/or with an implant stability quotient (ISQ) <70 were considered failed for immediate loading. A statistical analysis was performed.

RESULTS

Thirty implants were placed in postextraction sockets of 17 patients, and 32 implants were placed in healed sites of 22 patients. There were no statistically significant differences in ISQ values between the 2 groups, at each assessment. In total, 60 implants (96.8%) had an IT ≥45 and an ISQ ≥70 at placement and at each follow-up control: all these implants were successfully loaded. Only 2 implants (1 in a postextraction socket and 1 in a healed site, 3.2%) could not achieve an IT ≥45 N·cm and/or an ISQ ≥70 at placement or over time: accordingly, these were considered failed for stability, as they could not be subjected to immediate loading. One of these 2 implants, in a healed site of a posterior maxilla, had to be removed, yielding an overall 1-year implant survival rate of 98.4%. No complications were reported. No significant differences were reported between the 2 groups with respect to implant failures and complications.

CONCLUSION

Immediately loaded implants placed in postextraction sockets and healed sites had similar high survival and stability, with no reported complications. Further long-term studies on larger samples of patients are needed to confirm these results.

Fixed Full Arches Supported by Tapered Implants with Knife-Edge Thread Design and Nanostructured, Calcium-Incorporated Surface: A Short-Term Prospective Clinical Study

Purpose. To evaluate implant survival, peri-implant bone loss, and complications affecting fixed full-arch (FFA) restorations supported by implants with a knife-edge thread design and nanostructured, calcium-incorporated surface. Methods. Between January 2013 and December 2015, all patients referred for implant-supported FFA restorations were considered for enrollment in this study. All patients received implants with a knife-edge thread design and nanostructured calcium-incorporated surface (Anyridge®, Megagen, South Korea) were restored with FFA restorations and enrolled in a recall program. The final outcomes were implant survival, peri-implant bone loss, biologic/prosthetic complications, and “complication-free” survival of restorations. Results. Twenty-four patients were selected. Overall, 215 implants were inserted (130 maxilla, 85 mandible), 144 in extraction sockets and 71 in healed ridges. Thirty-six FFAs were delivered (21 maxilla, 15 mandible): 27 were immediately loaded and 9 were conventionally loaded. The follow-up ranged from 1 to 3 years. Two fixtures failed, yielding an implant survival rate of 95.9% (patient-based). A few complications were registered, for a “complication-free” survival of restorations of 88.9%. Conclusions. FFA restorations supported by implants with a knife-edge thread design and nanostructured, calcium-incorporated surface are successful in the short term, with high survival and low complication rates; long-term studies are needed to confirm these outcomes.

Three-Year Outcome of Fixed Partial Rehabilitations Supported by Implants Inserted with Flap or Flapless Surgical Techniques

PURPOSE

The aim of this prospective clinical study was to evaluate the 3-year outcome of fixed partial prostheses supported by implants with immediate provisionalization without occlusal contacts inserted in predominantly soft bone with flap and flapless protocols.

MATERIALS AND METHODS

Forty-one patients partially rehabilitated with 72 NobelSpeedy implants (51 maxillary; 21 mandibular) were consecutively included and treated with a flapless surgical protocol (n = 20 patients; 32 implants) and flapped surgical protocol (n = 21 patients; 40 implants). Primary outcome measure was implant survival; secondary outcome measures were marginal bone resorption (comparing the bone levels at 1 and 3 years with baseline) and the incidence of biological, mechanical, and esthetic complications. Survival was computed through life tables; descriptive statistics were applied to the remaining variables of interest.

RESULTS

Eight patients with eight implants dropped out of the study. One implant failed in one patient (flapless group) giving an overall cumulative survival rate (CSR) of 98.6%. No failures were noted with the flapped protocol (CSR 100%), while for the implants placed with the flapless surgical technique, a 96.9% CSR was registered. The overall average marginal bone resorption at 3 years was 1.37 mm (SD = 0.94 mm), with 1.14 mm (SD = 0.49 mm) and 1.60 mm (SD = 1.22 mm) for the flap and flapless groups, respectively. Mechanical complications occurred in nine patients (n = 5 patients in the flapless group; n = 4 patients in the flap group). Implant infection was registered in three implants and three patients (flapless group), who exhibited inadequate oral hygiene levels.

CONCLUSIONS

Partial edentulism rehabilitation through immediate provisionalization fixed prosthesis supported by dental implants inserted through flap or flapless surgical techniques in areas of predominantly soft bone was viable at 3 years of follow-up. The limitations and risks of the "free-hand" method in flapless surgery should be considered when planning implant-supported fixed prosthetic reconstructions.