An In Vitro Biomechanical Comparison of a Prototype Equine Metacarpal Dynamic Compression Plate Fixation with Double Dynamic Compression Plate Fixation of Osteotomized Equine Third Metacarpal Bones

Biomechanical properties of a novel locking compression plate to stabilize oblique tibial osteotomies in buffaloes

OBJECTIVE

Quantitation of mechanical properties of a novel locking compression plate (LCP) for bovine tibia.

STUDY DESIGN

Prospective in vitro study.

SAMPLE POPULATION

Adult Murrah buffalo (250-350 kg) tibiae.

METHODS

Forty tibiae were randomly assigned to five treatment groups (n = 8/group): intact bone and bone constructs with a standard nonlocking plate, single LCP, double LCP, and novel LCP. During implant application, a mid-diaphyseal, oblique osteotomy was performed in all constructs, which were subsequently tested in axial compression (n = 4 each) or three-point craniocaudal bending (n = 4 each). Novel LCP alone (n = 4) was tested only in bending. Stiffness, yield load, ultimate failure load, and bending moment were determined from the load deformation curves and compared among different treatment groups (P < .05).

RESULTS

Under compression, yield load of the novel LCP (24.07 ± 3.45 kN) was greater than that of the nonlocking plate (11.10 ± 2.46 kN) and the single LCP (18.01 ± 2.07 kN) but less than that of the double LCP (30.61 ± 1.95 kN), and ultimate failure load of the novel LCP (25.85 ± 4.32 kN) was greater than that of the nonlocking plate (13.18 ± 2.91 kN) but similar to that of the single LCP (21.17 ± 2.33 kN) and the double LCP (32.40 ± 1.46 kN). Bending moment, yield load, and ultimate failure load of the novel LCP were 565.37 ± 79.30 Nm, 7.90 ± 1.14 kN, 9.83 ± 1.38 kN, respectively, which were greater than those of the nonlocking plate and the single LCP but comparable to those of the double LCP.

CONCLUSION

The novel LCP developed for bovine tibia was mechanically superior to the standard nonlocking plate or the single LCP and comparable to the double LCP.

CLINICAL SIGNIFICANCE

The novel LCP may provide rigid fixation of tibial diaphyseal fractures in buffaloes and cattle weighing 250 to 350 kg.

Effect of sequential removal of parts of the second metacarpal bone on the biomechanical stability of the equine carpus

OBJECTIVE

To quantify changes in biomechanical stability and stiffness within the equine carpus after removal of 50%, 80%, and 100% of the second metacarpal bone (MC2).

STUDY DESIGN

In vitro biomechanical study.

METHODS

Cadaveric equine forelimbs (n = 16) were evaluated. Intact constructs were loaded in axial compression from 0 to 5000 N and compression + torsion (5000 N ± 20°) for 5 cycles. This was repeated after removal of 50%, 80%, and 100% of MC2. The primary biomechanical outcome variables were the compressive stiffness and compressive + torsional stiffness of the carpus. Relative kinematic motion was also evaluated between the second carpal bone (C2) and the radial carpal bone (RC), C2 and the third metacarpal bone (MC3) and C2 and the third carpal bone (C3).

RESULTS

A significant decrease in compressive + torsional stiffness was found after 100% removal of MC2. Compressive stiffness of the carpus did not change after 100% MC2 removal. A significant increase in relative rotation around the z-axis (rotation around the long axis) was observed for C2 versus MC3 and C2 versus C3 when 100% of MC2 was removed as compared to 80%, 50%, and 0% removal. No significant difference in relative rotation between C2 and RC was detected.

CONCLUSIONS

The biomechanical results reported here suggest that the torsional stability of the equine carpus is significantly decreased only after complete resection of MC2.

In vitro biomechanical evaluation and comparison of a new prototype locking plate and a limited-contact self compression plate for equine fracture repair

OBJECTIVE

To determine if the mechanical properties (strength and stiffness) of a new prototype 4.5 mm broad locking plate (NP-LP) are comparable with those of a traditional 4.5 mm broad limited-contact self compression plate (LC-SCP), and to compare the bending and torsional properties of the NP-LP and LC-SCP when used in osteotomized equine third metacarpal bones (MC3).

METHODS

The plates alone were tested in four-point bending single cycle to failure. The MC3-plate constructs were created with mid-diaphyseal osteotomies with a 1 cm gap. Constructs were tested in four-point bending single cycle to failure, four-point bending cyclic fatigue, and torsion single cycle to failure.

RESULTS

There were not any significant differences in bending strength and stiffness found between the two implants. The MC3-NP-LP construct was significantly stiffer than the MC3-LC-SCP in bending. No other biomechanical differences were found in bending, yield load in torsion, or mean composite rigidity. Mean cycles to failure for bending fatigue testing were similar for both constructs.

CLINICAL SIGNIFICANCE

The NP-LP was comparable to the LC-SCP in intrinsic, as well as structural properties. The NP-LP construct was more rigid than the LC-SCP construct under four-point bending, and both constructs behaved similarly under four-point bending cyclic fatigue testing and torsion single cycle to failure. The new NP-LP implant fixation is biomechanically comparable to the LC-SCP in a simulated MC3 fracture.

An In Vitro Biomechanical Comparison Between Prototype Tapered Shaft Cortical Bone Screws and AO Cortical Bone Screws for an Equine Metacarpal Dynamic Compression Plate Fixation of Osteotomized Equine Third Metacarpal Bones

OBJECTIVES

To compare biomechanical properties of a prototype 5.5 mm tapered shaft cortical screw (TSS) and 5.5 mm AO cortical screw for an equine third metacarpal dynamic compression plate (EM-DCP) fixation to repair osteotomized equine third metacarpal (MC3) bones.

STUDY DESIGN

Paired in vitro biomechanical testing of cadaveric equine MC3 with a mid-diaphyseal osteotomy, stabilized by 1 of 2 methods for fracture fixation.

ANIMAL POPULATION

Adult equine cadaveric MC3 bones (n=12 pairs).

METHODS

Twelve pairs of equine MC3 were divided into 3 groups (4 pairs each) for (1) 4-point bending single cycle to failure testing, (2) 4-point bending cyclic fatigue testing, and (3) torsional single cycle to failure testing. An EM-DCP (10-hole, 4.5 mm) was applied to the dorsal surface of each, mid-diaphyseal osteotomized, MC3 pair. For each MC3 bone pair, 1 was randomly chosen to have the EM-DCP secured with four 5.5 mm TSS (2 screws proximal and distal to the osteotomy; TSS construct), two 5.5 mm AO cortical screws (most proximal and distal holes in the plate) and four 4.5 mm AO cortical screws in the remaining holes. The control construct (AO construct) had four 5.5 mm AO cortical screws to secure the EM-DCP in the 2 holes proximal and distal to the osteotomy in the contralateral bone from each pair. The remaining holes of the EM-DCP were filled with two 5.5 mm AO cortical screws (most proximal and distal holes in the plate) and four 4.5 mm AO cortical screws. All plates and screws were applied using standard AO/ASIF techniques. Mean test variable values for each method were compared using a paired t-test within each group. Significance was set at P<.05.

RESULTS

Mean 4-point bending yield load, yield bending moment, bending composite rigidity, failure load and failure bending moment of the TSS construct were significantly greater (P<.00004 for yield and P<.00001 for failure loads) than those of the AO construct. Mean cycles to failure in 4-point bending of the TSS construct was significantly greater (P<.0002) than that of the AO construct. The mean yield load and composite rigidity in torsion of the TSS construct were significantly greater (P<.0039 and P<.00003, respectively) than that of the AO construct.

CONCLUSION

The TSS construct provides increased stability in both static overload testing and cyclic fatigue testing.

CLINICAL RELEVANCE

The results of this in vitro study support the conclusion that the EM-DCP fixation using the prototype 5.5 mm TSS is biomechanically superior to the EM-DCP fixation using 5.5 mm AO cortical screws for the stabilization of osteotomized equine MC3.