The effects of temperature on cardiac pacing thresholds

Acute pacing threshold elevation during simultaneous Micra leadless pacemaker implantation and AV node ablation: Clinical cases, computer model and practical recommendations

BACKGROUND

In patients with refractory atrial fibrillation (AF), atrioventricular nodal (AVN) ablation and permanent pacemaker implantation is recommended. The Micra Transcatheter Pacing System (Micra) is a single chamber leadless pacemaker (LPM) and thus offers the possibility of AV node (AVN) ablation in the same procedure. Pacing threshold (PT) elevation after radiofrequency (RF) ablation is a potential complication.

METHODS

We conducted a single center retrospective cohort study. Patients implanted with a Micra (n = 84) and concomitant or delayed AVN ablation (n = 12) from 2014 to 2022 were included. Two cases of acute Micra PT elevation immediately following RF AVN ablation required device retrieval and implantation of a new Micra. Procedural characteristics and electrophysiological parameters were analyzed, and a computer model was performed to determine factors responsible for acute PT elevations.

RESULTS

A total of 84 patients were included. Mean age was 74 ± 10 and 48% were women. Twelve patients (14%) underwent AVN ablation. Two patients had acute PT elevation requiring device retrieval despite no direct contact of the ablation catheter with the Micra. Computer modeling shows that significant dissipated power due to electrical field coupling can occur at the tip or ring electrode if the catheter is not kept at a safe distance (≥35 mm) from the Micra when a maximum power of 100 W is delivered.

CONCLUSION

Concurrent AVN ablation and Micra implantation is safe in most patients. To prevent acute PT elevation, keeping a safe distance of ≥35 mm from the tip and ring electrodes of the Micra and using lower power output may prevent this complication.

In vitro contractile studies within isolated tissue baths: Translational research from Visible Heart® Laboratories

The isolated tissue bath research methodology was first developed in 1904. Since then, it has been recognized as an important tool in pharmacology and physiology research, including investigations into neuromuscular disorders. The tissue bath is still used routinely as the instrument for performing the "gold standard" test for clinical diagnosis of malignant hyperthermia susceptibility - the caffeine-halothane contracture test. Our research group has utilized this tool for several decades for a range of research studies, and we are currently one of four North American diagnostic centers for determining susceptibility for malignant hyperthermia. This review provides a brief summary of some of the historical uses of the tissue bath. Important experimental considerations for the operation of the tissue bath are further described. Finally, we discuss the different studies our group has performed using isolated tissue baths to highlight the broad potential applications.

Laser surface modification of medical grade alloys for reduced heating in a magnetic resonance imaging environment

Nanoscale surface modification of medical grade metallic alloys was conducted using a neodymium-doped yttrium aluminum garnet laser-based dopant diffusion technique. The objective of this approach was to minimize the induction heating by reducing the absorbed radio frequency field. Such an approach is advantageous in that the dopant is diffused into the alloy and is not susceptible to detachment or spallation as would an externally applied coating, and is expected to not deteriorate the mechanical and electrical properties of the base alloy or device. Experiments were conducted using a controlled environment laser system with the ability to control laser properties (i.e., laser power, spot size, and irradiation time) and dopant characteristics (i.e., temperature, concentration, and pressure). The reflective and transmissive properties of both the doped and untreated samples were measured in a radio frequency (63.86 MHz) magnetic field using a system comprising a high power signal generator, a localized magnetic field source and sensor, and a signal analyzer. The results indicate an increase in the reflectivity of the laser-treated samples compared to untreated samples. The effect of reflectivity on the heating of the alloys is investigated through a mathematical model incorporating Maxwell's equations and heat conduction.

Disparity in left ventricular stimulation among different pacing configurations in cardiac resynchronization therapy

BACKGROUND

Cardiac resynchronization therapy (CRT) demands high energy utilization due to continuous biventricular pacing. Current technology allows 6 pacing configurations for a bipolar left ventricular (LV) lead. Understanding the energy requirements for each configuration will allow optimization of pacing output.

METHODS AND RESULTS

Pacing impedance, LV voltage threshold at 1.5 ms (rheobase) and 0.4 ms and chronaxie were obtained in 6 LV configurations in 49 consecutive patients undergoing CRT implantation or replacement. Strength-duration curves were derived using the Lapicque formula. Pacing impedances and voltage thresholds at 1.5 and 0.4 ms, calculated minimum threshold energy at chronaxie, current drain, energy thresholds at 0.4 ms, and strength-duration curves were statistically different between LV configurations (P<0.05). The lowest threshold energy requirements were found in Tip→right ventricular (RV) coil and Tip→Can configuration. Energy strength-duration curves involving the ring as the cathode (Ring→RV, Ring→Can, and Ring→Tip) had the highest LV thresholds. The pacing configuration with the lowest energy threshold correlated 89% of the time with the lowest voltage threshold at 0.4 ms. The probability to reach LV thresholds <1.5 V at 0.4 ms was increased from 51% with 2 LV configurations to 67% with 6 LV configurations.

CONCLUSIONS

Pacing impedance, LV thresholds, minimum threshold energy at chronaxie, current drain, voltage, and energy strength-duration curves were statistically different between LV pacing configurations. LV pacing configuration with the lowest voltage threshold does not always reflects the lowest energy threshold, particularly in the presence of a low impedance configuration. The availability of 6 LV configurations increases the probability of optimizing LV pacing output.