Young's modulus of warm and cold gutta-percha

Biomechanical analysis and comparison of 12 dental implant systems using 3D finite element study

Finite element analysis plays an important role in dental implant design. The objective of this study was to show the effect of the overall geometry of dental implants on their biomechanics after implantation. In this study, 12 dental implants, with the same length, diameter and screw design, were simulated from different implant systems. Numerical model of right mandibular incisor bone segment was generated from CT data. The von-Mises stress distributions and the total deformation distributions under vertical/lateral load were compared for each implant by scores ranking method. The implants with cylindrical shapes had highest scores. Results indicated that cylindrical shape represented better geometry over taper implant. This study is helpful in choosing the optimal dental implant for clinical application and also contributes to individual implant design. Our study could also provide reference for choice and modification of dental implant in any other insertion sites and bone qualities.

Teeth restored using fiber-reinforced posts: in vitro fracture tests and finite element analysis

In dentistry the restoration of decayed teeth is challenging and makes great demands on both the dentist and the materials. Hence, fiber-reinforced posts have been introduced. The effects of different variables on the ultimate load on teeth restored using fiber-reinforced posts is controversial, maybe because the results are mostly based on non-standardized in vitro tests and, therefore, give inhomogeneous results. This study combines the advantages of in vitro tests and finite element analysis (FEA) to clarify the effects of ferrule height, post length and cementation technique used for restoration. Sixty-four single rooted premolars were decoronated (ferrule height 1 or 2 mm), endodontically treated and restored using fiber posts (length 2 or 7 mm), composite fillings and metal crowns (resin bonded or cemented). After thermocycling and chewing simulation the samples were loaded until fracture, recording first damage events. Using UNIANOVA to analyze recorded fracture loads, ferrule height and cementation technique were found to be significant, i.e. increased ferrule height and resin bonding of the crown resulted in higher fracture loads. Post length had no significant effect. All conventionally cemented crowns with a 1-mm ferrule height failed during artificial ageing, in contrast to resin-bonded crowns (75% survival rate). FEA confirmed these results and provided information about stress and force distribution within the restoration. Based on the findings of in vitro tests and computations we concluded that crowns, especially those with a small ferrule height, should be resin bonded. Finally, centrally positioned fiber-reinforced posts did not contribute to load transfer as long as the bond between the tooth and composite core was intact.

An ex vivo comparison of three different gutta-percha cones when compacted at different temperatures: rheological considerations in relation to the filling of lateral canals

AIM

To compare ex vivo the penetration of three brands of gutta-percha cones, compacted under a constant force and heated to different temperatures, into artificial lateral canals.

METHODOLOGY

Resin blocks with simulated main canals, each having two lateral canals (C at 6.5 and A at 13 mm from the surface of the resin block), were selected. A gutta-percha cone, either Mynol MF, Hygenic MF or GT Tulsa 0.04 was compacted into each main canal for 5 s using a wire rod with a diameter of 0.7 mm soldered to the bottom of a metal cylinder, with a force of 2.7 kg at controlled temperatures of 37, 42, 47, 52, 60 degrees C. The penetration of each brand of gutta-percha into 60 lateral canals (10 at each temperature) was measured using a stereomicroscope. Statistical analysis was performed using the ANOVA, the Scheffè test and the t-test.

RESULTS

None of the three brands of cones entered up to 0.1 mm within either lateral canal until a temperature of 47 degrees C was reached; at that temperature only Mynol cones (P < or = 0.05) penetrated in four of 10 A-level canals (mean 0.13 +/- 0.19 mm) and in all 10 C-level canals (mean 0.43 +/- 0.12 mm). The A-level lateral canals were penetrated at 52 degrees C by Mynol cones (mean 0.76 +/- 0.34 mm) to a significantly greater distance (P < or = 0.05) than Tulsa cones (mean 0.31 +/- 0.12 mm) and Hygenic cones (mean 0.11 +/- 0.08 mm). At 60 degrees C the Mynol cones (mean 1.93 +/- 0.34 mm) penetrated significantly more (P < or = 0.05) than the Tulsa cones (mean 0.86 +/- 0.22 mm) and Hygenic cones (mean 0.67 +/- 0.19 mm). The C-level lateral canals were penetrated at 52 degrees C by Mynol cones (mean 0.91 +/- 0.29 mm) to a significantly greater distance (P < or = 0.05) than Tulsa cones (mean 0.47 +/- 0.16 mm) and Hygenic cones (mean 0.46 +/- 0.15 mm), whilst no significant difference was found at 60 degrees C.

CONCLUSIONS

When heated and compacted, the three gutta-percha cones penetrated the lateral canals to different degrees. They penetrated more than 0.43 mm into the lateral canals only at temperatures higher than 47 degrees C.

Intracanal temperature rise evaluation during the usage of the System B: replication of intracanal anatomy

AIM

To evaluate and determine intracanal temperature rises at 2 and 4 mm from the working length (WL) necessary to obtain proper replication of intracanal anatomy with gutta-percha (GP) using the System B heat source during vertical condensation.

METHODOLOGY

A split-tooth model was prepared and artificial shallow depressions were cut in the buccal canal wall 2 and 4 mm from the WL. At the same level on the palatal wall holes were drilled to adapt two thermocouples. The canal was filled using GP in a vertical condensation technique by placing the System B plugger at 2 and 4 mm from the WL in groups A and B, respectively. Two control groups in which no GP was used were carried out placing the plugger 2 and 4 mm from the WL (groups A.c and B.c, respectively) and activating the heat source. Recording of temperature rise was carried out during the filling procedure for groups A and B and during activation for control groups A.c and B.c; the highest temperatures were recorded. After each filling was completed, 3 min were allowed for the GP to cool and the model divided to reveal the filling. Images of the GP were taken with a CCD camera to evaluate the presence of replication of artificial round depressions. In control groups, the temperature was recorded for 20 s after a 3 s activation of the heat source. The rise in temperature was compared between the groups individually at each level (2 or 4 mm) and statistically analysed using one-way anova and Fisher PLSD tests at 5% of significance level (P < 0.05).

RESULTS

Mean temperature rises of 14 +/- 3 and 12 +/- 2 degrees C at 2 and 4 mm from the WL, respectively, were observed in group A fillings, and 4 +/- 1 and 6 +/- 1 degrees C at 2 and 4 mm, respectively, in group B fillings. Recordings at 2 mm showed significantly (P < 0.05) higher temperature rises with group A.c when compared with groups B and B.c. Replication of intracanal anatomy with GP was always found in group A fillings at both levels but only 4 mm from the WL in group B fillings.

CONCLUSIONS

Positioning the plugger close to WL and a temperature rise of 6 degrees C were necessary to obtain replication of intracanal anatomy. A mean temperature rise of 4 degrees C at 2 mm from WL (group B) resulted in no replication of intracanal anatomy. Further studies simulating clinical conditions are necessary.

Analysis of the endogrammes developed during obturations on extracted teeth using system B

The ability of an obturation technique to fill the root canal system tridimensionally depends partially on the timing and intensity of force applications. The aim of this study was to use the Endographe to analyze the forces and wedging effects developed in the root canal using a new obturation technique: System B. This system uses a heat plugger that simultaneously heats and pushes gutta-percha. The plugger was used to soften and move the gutta-percha apically during the down-pack stage. Two different methods, however, were used to withdraw the plugger from the compacted gutta-percha. One used the burst heat method, and the other was cold withdrawal. Five endodontists performed 50 obturations of prepared extracted teeth and 50 obturations of the "wedging effect" holder of the Endographe. The practitioner-obturation assignment was randomized. For each obturation the biggest plugger possible in relationship to the shape of the canal was chosen. For the obturation of the special holder the same tip was chosen. Endogrammes showed the force application and wedging effect sequences. The mean values for the vertical and horizontal forces and the wedging effect were, respectively, 16 +/- 2 N, 5 +/- 1 N, and 9 +/- 1 N. These results suggest that System B is one of the best techniques in terms of the developed vertical forces (low values) and the resulting wedging effect (high values) in relationship to the plasticity of the gutta-percha. The Endogrammes provide a new approach to the analysis of obturation techniques and a means to demonstrate correct and optimal manipulation of the new System B plugger.

Additional studies on the distribution of stresses during vertical compaction of gutta-percha in the root canal

OBJECTIVE

This study was designed to investigate the effect of certain pathological alterations of the dental structures (diminishing bone support, internal resorption, root perforation, periapical lesion) on stress distribution during root canal filling procedures by the warm vertical compaction technique.

DESIGN

The computer stress analyses were done for a maxillary canine tooth model which was based on dimensions recovered from a human cadaveric maxilla scanned by CT.

METHODS

The finite element method was used to calculate the stresses generated during root canal filling procedures by warm vertical compaction technique. Patterns of stress distribution associated with various alterations in dental structures were investigated. For this purpose 60 cases were simulated. The hypothetical force of 10 N is taken as a unit representation. For other magnitudes of applied force, the corresponding stresses would be scaled directly because the calculations were made for linear materials.

RESULTS AND CONCLUSION

It is found that, when diminishing bone support and internal resorption are concurrently simulated, a marked increase in stress magnitudes occur (maximum von Mises stress 5.37 N/mm2). However, these values still remain much below the most frequently reported tensile strength of dentine (50-100 N/mm2). If dentist's handwork is transformed into equivalent edge tractions on gutta-percha, then stresses in dentine, even when they are corrected for 3-kg applied force, appear to remain below fracture strengths of this material. This result leads us to conclude that when warm vertical compaction technique is skillfully performed and inadvertent undue force is not applied, a premature root fracture in a large rooted maxillary anterior tooth with straight root canal anatomy is not likely to occur, even for the unfavourable conditions simulated in our model. This result, like all results derived from modelling applications, is of course contingent upon agreement between the way in which the clinical operations are performed and the way in which they are mirrored for computer representation. We believe that the approach described here avoids the spurious stresses that have been reported in similar investigations.

Analysis of forces developed during obturations. Wedging effect: Part II

The aim of this study was to use a force analyzer device, the modified Endographe with a new cupule, to compare the forces and wedging effects developed in the root canal using four obturation techniques: warm vertical compaction, lateral condensation, thermomechanical compaction, and Thermafil condensation. The different methods--that varied in instrumentation, duration, and compaction load--were studied from graphs representing the force application sequences. In addition, the graphs resulting from modifications in technique (such as using an undersized spreader and pluggers that were either too small or too big) and deliberately induced failures in technique (by use of a too small condenser or a too small master cone) were studied. The mean values for the wedging effect for warm vertical compaction, lateral condensation, thermomechanical compaction, and Thermafil condensation were, respectively, 0.65 +/- 0.07 kg, 0.8 +/- 0.1 kg, 0.6 +/- 0.08 kg, and 0.03 +/- 0.01 kg. The use of graphs provides a new approach to the analysis of obturation techniques.

Analysis of forces developed during obturations. Wedging effect: Part I

The aim of this study was to define the "wedging effect" created by the intracanal forces developed during obturations and to measure it using a force analyzer device. In endodontics, the wedging effect is the result of, for example, a plugger pushing gutta-percha into a canal: the plugger functions much as the rod of a hydraulic jack and the vertical force applied by this rod induces in the cylinder (i.e. the canal) a hydrostatic pressure that is relatively equal in all directions. It is these forces resulting from the hydrostatic pressure that have been labeled the wedging effect. The original device, the Endographe, had a monobloc cupule for measuring the external vertical and horizontal forces developed by a practitioner, but it was unable to measure the intracanal forces. With a new cupule composed of two independent parts joined under pressure, the wedging effect was recorded and analyzed. Two obturation methods, warm vertical compaction and lateral condensation, were performed by endodontists. The forces were depicted by Endogrammes as a function of time. For all of the forces developed during the two techniques, the mean values showed a nonsignificant difference between the different practitioners. The use of graphs provides a new approach to the analysis of intracanal forces as they develop our time and permits the comparison of different obturation techniques.

Dental materials: 1996 literature review

This critical review of the published literature on dental materials for the year 1996 has been compiled by the Dental Materials Panel of the UK. It continues the series of annual reviews started in 1973 and published in the Journal of Dentistry. Emphasis has been placed upon publications which report upon the materials science or clinical performance of the materials. The review has been divided by accepted materials classifications (fissure sealants, glass polyalkenoate cements, dentine bonding, dental amalgam, endodontic materials, casting alloys, resin-bonded bridges and ceramo-metallic restorations, ceramics, denture base resins and soft lining materials, impression materials, implants materials, orthodontic materials, biomechanics and image processing, resin composites and casting investment materials and waxes). Three hundred and thirteen articles have been reviewed.