Evaluation of the thermoplasticity of different gutta-percha cones and Resilon�

Filling ability of ready-to-use or powder-liquid calcium silicate-based sealers after ultrasonic agitation

This study evaluated the effect of ultrasonic agitation on the filling capacity of ready-to-use calcium silicate-based sealer Bio-C Sealer (BCS, Angelus, Paraná, Brazil) or powder-liquid BioRoot RCS (BR, Septodont, Saint-Maur-des-Fossés, France) using curved artificial canals by micro-computed tomography (micro-CT). Additionally, flow (mm) and flow area (mm2) were evaluated for both materials. Acrylic resin main canal (60° curvature and 5 mm radius, with 3 lateral canals in the cervical, middle, and apical thirds) were prepared up to size 40/.05 (Prodesign Logic, Brazil). The agitation method was used with ultrasonic tip (US, Irrisonic, Helse, Brazil): BCS, BCS/US, BR, and BR/US. All specimens were filled using the single-cone technique. The samples were scanned by micro-CT (8,74 µm) after obturation. The percentage of filling material and voids were calculated. Flow was evaluated based on ISO 6876/2012 standards (mm) and area (mm2). The data were statistically analyzed using ANOVA and Tukey tests (α = 0.05). BR/US showed lower percentage of filling material in the lateral canals than and, BCS/US (p<0.05). BR/US resulted in a higher percentage of voids than BR in the lateral apical third (p<0.05). BCS showed higher flow than BR (p<0.05). BCS and BR presented proper filling capacity in the simulated curved canals regardless of the use of ultrasonic agitation. However, BR/US showed more voids in the apical third. BCS demonstrates higher filling ability.

Physicochemical Properties and Bioactive Potential of a New Epoxy Resin-based Root Canal Sealer

The aim of this study was to evaluate physicochemical properties and bioactive potential of Sealer Plus, in comparison with MTA Fillapex, Sealapex and AH Plus. Setting time, flow, and radiopacity were evaluated based on ISO 6876 Standard. Flow was also assessed in area (mm²). The solubility and volumetric change of the sealers were evaluated after 7 and 30 days of immersion in distilled water. Solubility was evaluated by the difference in mass of materials before and after immersion. Volumetric change was evaluated by using microcomputed tomography (micro-CT). The bioactive potential was observed by Scanning Electron Microscopy (SEM) after immersion in PBS. Data were compared using ANOVA and Tukey tests (α=0.05). Sealer Plus presented the shortest setting time (196 min.) and Sealapex the longest (912 min.) (p<0.05). AH Plus showed the highest radiopacity (9.5 mm Al) and MTA Fillapex the lowest (2.7 mm Al) (p<0.05). All the sealers presented flow in accordance with ISO 6876/2012 (>17 mm). Sealer Plus showed low solubility and volumetric change (<1%), and MTA Fillapex showed the highest solubility (>25%), and volumetric change (>4%) after all time intervals (p<0.05). MTA Fillapex was the only sealer that showed bioactive potential. In conclusion, Sealer Plus presented proper physicochemical properties. However, this sealer did not present a bioactive potential.

Evaluation of flow and filling of root canal sealers using different methodologies

Abstract Introduction Flow and filling ability of root canal sealers are indispensable for hermetic sealing of the root canal. Micro-computed tomography (micro-CT) can be used as a complementary methodology to evaluate such properties. Objective To evaluate the flow and filling ability of AH Plus, Endofill and Sealapex by conventional methodology and micro-CT. Material and method The flow of the sealers was analyzed according to ISO 6876/2012 and complemented by the area evaluation. Glass plates were manufactured with diameters of 1×1×2 mm and 1×1×1 mm (length, width and height), with a central cavity and four grooves in the horizontal and vertical directions. Each material was placed in the central cavity. Another glass plate and a metal weight were placed on the cement and kept for 10 minutes. The glass plate/sealer set was scanned using micro-CT. The flow was calculated by linear measurement of the material in the grooves. The central filling (mm3) was calculated in the central cavity and the lateral filling was measured up to 2 mm from the central cavity. Data were submitted to ANOVA/Tukey tests (α=0.05). Result All evaluated sealers presented flow according to ISO 6876 standards. The materials showed central cavity filling capacity higher than 80% and lateral filling greater than 75%. There was no difference in flow (mm and mm2) and in the filling ability (mm3) provided by the materials (p>0.05). Conclusion All evaluated root canal sealers showed adequate flow and filling capacity, suggesting their clinical application.

Physicochemical Properties and Volumetric Change of Silicone/Bioactive Glass and Calcium Silicate-based Endodontic Sealers

INTRODUCTION

This study evaluated setting time (ST), radiopacity, pH, flow, solubility, and volumetric change (VC) of a silicone, gutta-percha, and bioactive glass-based sealer, GuttaFlow Bioseal (GFB), and a calcium silicate-based sealer, TotalFill BC Sealer (TFBC), in comparison with AH Plus.

METHODS

ST and flow were evaluated in accordance with the ISO 6876 Standard. pH was evaluated after different time intervals (1, 3, 7, 14, 21, and 28 days). Radiopacity was evaluated by radiographic analysis in millimeters of aluminum. Solubility was evaluated by means of mass loss (%) after 7 and 30 days of immersion in distilled water. VC was evaluated by micro-computed tomography, by using cavities 3 mm deep and 1 mm in diameter in acrylic resin, filled with the materials. The materials were evaluated after setting and after 7 and 30 days of immersion in distilled water. The data were submitted to analysis of variance and Tukey statistical tests (P < .05).

RESULTS

TFBC demonstrated the highest pH and solubility. GFB had the shortest ST, and lowest radiopacity and flow values. VC was similar for the sealers in both time intervals.

CONCLUSIONS

TFBC presented the highest pH and solubility, but showed similar VC to GFB and AH Plus. GFB showed proper physicochemical properties. Micro-computed tomography complements the physicochemical analysis of endodontic sealers.

Filling of simulated lateral canals with gutta-percha or thermoplastic polymer by warm vertical compaction

The aim of this study was to evaluate the ability of gutta-percha and a thermoplastic synthetic polymer (Resilon) to fill simulated lateral canals, using warm vertical compaction. Forty-five single-rooted human teeth were prepared using the rotary crown-down technique. Artificial lateral canals were made at 2, 5, and 8 mm from the working length (WL) in each root. The specimens were divided into three groups (n = 15), according to the filling material: Dentsply gutta-percha (GD), Odous gutta-percha (GO), and Resilon cones (RE). The root canals were obturated using warm vertical compaction, without endodontic sealer. The specimens were subjected to a tooth decalcification and clearing procedure. Filling of the lateral canals was analyzed by digital radiography and digital photographs, using the Image Tool software. The data were subjected to the Kruskal-Wallis and Dunn tests at 5% significance. RE had the best filling ability in all root thirds (p < 0.05), with similar results for GO in the coronal third. In the middle and apical thirds, GD and GO had similar results (p > 0.05). Resilon may be used as an alternative to gutta-percha as a solid core filling material for use with the warm vertical compaction technique. The study findings point to the potential benefit of the warm vertical compaction technique for filling lateral canals, and the study provides further information about using Resilon and gutta-percha as materials for the warm vertical compaction technique.

Influence of addition of calcium oxide on physicochemical properties of Portland cement with zirconium or niobium oxide

Context:

Calcium oxide (CaO) may be added to mineral trioxide aggregate (MTA) or Portland cement (PC) to improve physicochemical and biological properties.

Aims:

To evaluate the physicochemical properties of PC associated with radiopacifiers and CaO.

Materials and Methods:

MTA Angelus, PC + 30% zirconium oxide (Zr), or 30% niobium oxide (Nb) associated with 10 or 20% of CaO were evaluated. Gilmore needles were used to evaluate initial and final setting time. Compressive strength was evaluated after the periods of 24 hours and 21 days. pH was analyzed after 3, 12, 24 hours, 7, 14, 21 days. Solubility and flow tests were performed based on the ISO 6876. The data obtained were submitted to analysis of variance and Tukey tests (P ≤ 0.05).

Results:

The associations with 10% CaO showed greater strength that the associations with 20% CaO. The shortest initial setting time was observed for the association PC + Zr + 20% CaO and MTA. All the cements presented alkaline pH. The flow of all cements was similar. The highest solubility was found in the associations with 20% CaO.

Conclusion:

The addition of CaO to PC favored the alkaline property and the PC + Zr + 20% CaO presented setting time similar to MTA.

Penetration of a resin-based filling material into lateral root canals and quality of obturation by different techniques

The aim of this study was to evaluate the penetration of a resin/polyester polymer-based material (Resilon Real Seal; SybronEndo Corp., Orange, USA) into simulated lateral canals, and the quality of obturations by different techniques. A total of 30 standardized simulated canals were divided into three groups according to the technique of obturation used: MS (McSpadden), SB (SystemB/Obtura II), and LC (Lateral Condensation). To analyze the penetration of the filling material, the simulated canals were digitalized and the images were analyzed using the Leica QWIN Pro v2.3 software. The data of the middle and apical thirds were separately submitted to analysis of variance (ANOVA), followed by the Tukey's test for the comparison of the techniques. Results showed a significant difference (p < 0.05) between groups (LC < SB) in the middle third, and a significant difference (p < 0.05) between groups (LC < SB and MS < SB) in the apical third. To analyze the quality of the obturations, the canals were radiographed and evaluated by three examiners. The Kappa test on interexaminer agreement and the nonparametric Kruskal-Wallis test indicated no significant difference between filling techniques. It was concluded that Resilon achieves greater levels of penetration when associated with thermoplastic obturation techniques.

Comparative evaluation of a novel smart-seal obturating system and its homogeneity of using cone beam computed tomography: In vitro simulated lateral canal study

Aim:

The aim was to evaluate and compare a novel polyamide polymer based obturating system and Gutta-percha and sealer in filling simulated lateral canals and their homogeneity when used for obturating the root canals.

Materials and Methods:

A total of 60 freshly extracted human single rooted teeth with fully formed apices were selected for this study. Teeth were de-coronated, and roots were standardized to a working length of 15 mm. Root canal preparation was carried out with rotary Protaper file system in all groups. The specimens were then randomly divided into three groups A, B, and C (n = 20). Ten samples from each group were decalcified and simulated lateral canals were made at 2, 4, and 6 mm from the root apex. Remaining ten samples from each group were maintained calcified. Group A was obturated with SmartSeal system (Prosmart-DRFP Ltd., Stamford, UK). Group B was obturated with sectional backfill method. Group C was obutrated with cold lateral compaction method (control). Decalcified samples from the respective groups were analyzed with digital radiography and photography and the measurement of the linear extension and area of lateral canal filling was done using UTHSCSA (UTHSCSA Image Tool for Windows version 3.0, San Antonio, TX, USA) software. Calcified samples were subjected to cone beam computed tomography image analysis sectioned axially.

Results:

Group A 92.46 ± 19.45 showed greatest extent of filling in lateral canals and denser homogeneity of oburation, followed by Group B 78.43 ± 26.45 and Group C 52.12 ± 36.67.

Conclusions:

Polyamide polymer obturation proved to have greater efficiency when compared with Gutta-percha system, when used for obturation with regards to adaptation of the sealer and penetration into the simulated lateral canals.

Resilon: a comprehensive literature review

Background and aims. An ideal root canal filling material should completely seal the entire root canal space and block communication between the root canal system and its surrounding tissues; it should also be nontoxic, noncarcinogenic, non-genotoxic, biocompatible, insoluble in tissue fluids and dimensionally stable. Bonding to dentin is a promising property, which can prevent leakage and improve the sealing ability of root canal filling materials. Resilon was developed and rec-ommended initially because the existing rootcanal filling materials did not bond to root canal dentin. Since its introduction in 2004, numerous reports have been published regarding various aspects of this material. The aim of this literature review is to present investigations regarding Resilon's physical and chemical properties and leakage studies. Materials and methods. A review of the literature was performed by using electronic and hand searching methods for Resilon from May 2004 to April 2012. Results. There are many published reports regarding Resilon. The searchshowed that Resilon is composed of a parent polymer, polycaprolactone or Tone, which is a biodegradable aliphatic polyester, with filler particles consisting of bioactive glass, bismuth oxychloride and barium sulfate. It possesses some antibacterial and antifungal properties. It is a promising material for root canal filling. Despite the presence of numerous case reports and case series regarding these applications, there are few designed research studies on clinical applications of this material. Resilon has some drawbacks such as high cost. Conclusion. Resilon seals well and is a biocompatible material. However, more clinical studies are needed to confirm its efficacy compared with other materials.

Effectiveness of gutta-percha and Resilon in filling lateral root canals using thermomechanical technique

OBJECTIVE: The aim of this study was to evaluate the effectiveness of gutta-percha and Resilon in filling lateral root canals in cervical, middle, and apical third using a thermomechanical technique. MATERIAL AND METHOD: Root canals of artificial teeth were prepared using a standard preparation. The lateral canals were fabricated using a 0.3-mm-diameter bur at 3 parts of each root. By using Tagger's hybrid technique with a McSpadden thermomechanical compactor, the root canal was filled using the following filling materials: Dentsply gutta-percha, Endopoint gutta-percha, and Resilon cones. The root canal fillings were evaluated using digitized radiographs and the Image Tool software. The percentage of filled area of each lateral canal was determined. The data were subjected to analysis of variance (ANOVA) and Tukey tests at a 5% significance level. RESULT: Resilon showed better effectiveness as a filling material. When the three thirds were compared, Resilon was more effective in the apical third than in the cervical third (p < 0.05). CONCLUSION: Resilon is an effective filling material for lateral root canals using a thermomechanical technique.

Ability of gutta-percha and Resilon to fill simulated lateral canals by using the Obtura II system

INTRODUCTION

The aim of this study was to evaluate the ability of Resilon (Resilon Research, LLC, North Branford, CT) and 2 types of gutta-percha to fill simulated lateral canals when using the Obtura II system (Model 823-700; Obtura Spartan, Fenton, MO).

METHODS

Forty-five human single-rooted teeth were selected and subjected to root canal preparation. After that, simulated lateral canals were made at 2, 5, and 8 mm from the working length (WL). The specimens were divided into 3 groups (n = 15) according to the filling material used: Obtura Flow 150 gutta-percha (Obtura flow), Odous Endo Flow gutta-percha (Odous; Odous De Deus Ind e Com. Ltda Belo Horizonte, MG, Brazil), and Resilon pellets (Resilon). Root canals were filled using the Obtura II system with the tip inserted to 3 mm from the WL. No sealer was used for root canal obturation. Specimens were subjected to a tooth decalcification and clearing method, and filling of the lateral canals was analyzed by digital radiography and photographs. The measurement of lateral canal filling was done using Image Tool software (UTHSCSA Image Tool for Windows version 3.0, San Antonio, TX). Data were statistically analyzed with the Kruskal-Wallis test at 5% significance.

RESULTS

All materials showed an ability to penetrate into the simulated lateral canals, with a minimum percentage of 73% in all thirds of the root canal.

CONCLUSIONS

It was concluded that gutta-percha and Resilon are solid core materials with a lateral canal filling ability when used with the Obtura II system.

Evaluation of the thermoplasticity of gutta-percha and Resilon® using the Obtura II System at different temperature settings

AIM

To analyse the thermoplasticity of several endodontic filling materials using the Obtura II System at different temperature settings.

METHODOLOGY

The following materials based on gutta-percha: Regular Obtura (OBT), Obtura Flow 150 (OBT F), Endo Flow (EDF), Odous (ODO) and the synthetic thermoplastic polymer material Resilon (RE) were heated using the Obtura II System at three temperature settings (140, 170 and 200 °C). Samples of the heated materials were placed on the sensor of a digital thermometer (THR-140; Instrutherm, São Paulo, Brazil) to determine their real temperature (RT) when the system was set at 140 °C (from 64.5 to 69 °C), 170 °C (from 73.8 to 77.5 °C) and 200 °C (from 83.6 °C for EDF and 100 °C for RE). Specimens (n = 30) were made by placing samples of each material in metallic ring moulds and compressing them between two glass slabs. After 24 h, specimens (n = 10) were heated at the different settings (RT) and submitted to compression under a 5-kg load. Plasticization was assessed by calculating the differences between the post-compression and initial diameters of each specimen. Data were submitted to anova and Tukey's test at 5% significance.

RESULTS

At 140 °C, Obtura Flow presented the highest thermoplasticity values and Regular Obtura, the lowest. At 170 °C, Obtura Flow and Resilon demonstrated greater plasticization. Resilon had the highest mean thermoplasticity values at 200 °C.

CONCLUSIONS

Thermoplasticity values were influenced both by the temperature settings on the Obtura II System and by the type of material analysed. Obtura Flow and Resilon had the highest mean thermoplasticity values.