Tooth wear: diet analysis and advice

Thickness and Substrate Effect on the Mechanical Behaviour of Direct Occlusal Veneers

PURPOSE

This study aimed to evaluate the fracture resistance and stress magnitude of occlusal veneers made of conventional or flowable resin composites at different minimal thicknesses bonded on enamel or dentin.

MATERIAL AND METHODS

A total of 120 sound bovine incisors were flattened and used as substrates (enamel or dentin) for the restorations. The teeth were embedded into polymethyl methacrylate and allocated into 4 groups according to the resin composite (Clearfil AP-X PLT and Clearfil Majesty Flow, Kuraray Dental) and substrate. Further, the substrates were randomly subdivided in 12 groups (N = 120, n = 10) according to the occlusal veneer minimal thickness: 0.5, 1.0, or 2.0 mm. The teeth were directly restored with a standardised procedure. Then, the specimens were loaded until fracture in a universal testing machine (Instron 6022, Instron Corp.). A 3-way and a 1-way analysis of variance were used to determine significant differences for each factor. Three-dimensional finite element analysis was carried out following the in vitro boundary conditions to assess the stress magnitude in the restoration during compressive loading.

RESULTS

The fracture loads were recorded into initial load to failure (ILF) and fatal load to failure (FLF). Differences were found in material for ILF and FLF, leading to an overall equal good performance in fracture load and stress distribution for both materials, regardless of the substrate. Differences in thickness were apparent in both ILF and FLF.

CONCLUSIONS

Direct conventional and flow resin composite occlusal veneers present a promising mechanical behaviour when bonded on enamel or dentin. However, caution is advised when preparing 0.5-mm minimal thickness restorations.

Effect of beverages on bovine dental enamel subjected to erosive challenge with hydrochloric acid

This study evaluated by an in vitro model the effect of beverages on dental enamel previously subjected to erosive challenge with hydrochloric acid. The factor under study was the type of beverage, in five levels: Sprite® Zero Low-calorie Soda Lime (positive control), Parmalat® ultra high temperature (UHT) milk, Ades® Original soymilk, Leão® Ice Tea Zero ready-to-drink low-calorie peach-flavored black teaand Prata® natural mineral water (negative control). Seventy-five bovine enamel specimens were distributed among the five types of beverages (n=15), according to a randomized complete block design. For the formation of erosive wear lesions, the specimens were immersed in 10 mL aqueous solution of hydrochloric acid 0.01 M for 2 min. Subsequently, the specimens were immersed in 20 mL of the beverages for 1 min, twice daily for 2 days at room temperature. In between, the specimens were kept in 20 mL of artificial saliva at 37ºC. The response variable was the quantitative enamel microhardness. ANOVA and Tukey's test showed highly significant differences (p<0.00001) in the enamel exposed to hydrochloric acid and beverages. The soft drink caused a significantly higher decrease in microhardness compared with the other beverages. The black tea caused a significantly higher reduction in microhardness than the mineral water, UHT milk and soymilk, but lower than the soft drink. Among the analyzed beverages, the soft drink and the black tea caused the most deleterious effects on dental enamel microhardness.

A literature review of dental erosion in children

Dental erosion is increasingly recognized as a common condition in paediatric dentistry with complications of tooth sensitivity, altered aesthetics and loss of occlusal vertical dimension. The prevalence of erosion in children has been reported to range from 10% to over 80%. The primary dentition is thought to be more susceptible to erosion compared to the permanent dentition due to the thinner and less mineralized enamel. The aim of this paper was to critically review dental erosion in children with regards to its prevalence, aetiology, diagnosis and prevention. The associations between erosion and other common conditions in children such as caries and enamel hypoplasia are also discussed.

Rehabilitation of the worn dentition

The purpose of this review was to evaluate the literature on the rehabilitation of tooth wear, with some pertinent historical, epidemiological and aetiological aspects of tooth wear provided as background information. In historical skull material, extensive tooth wear, assumed to be the result of coarser diets, was found even in relatively young individuals. Such wear is seldom seen in current populations. Although many of the factors associated with extensive tooth wear in historical material are no longer present or prevalent, new risk factors have emerged. In the young individual, the literature points to a global rise in soft drink consumption as the most significant factor in the development of tooth wear through dental erosion. Among older individuals, lifestyle changes and chronic diseases that are controlled with medications that may, in turn, result in regurgitation and/or dry mouth, are possible reasons amongst others for the widespread clinical impression of an increasing prevalence of tooth wear. The aetiology of tooth wear is multifactorial and the role of bruxism is not known. Clinical controlled trials of restorative and prosthodontic approaches for the range of clinical conditions that wear can give rise to, are limited in number and quality. Equally, the striking lack of evidence regarding the long-term outcomes of treatment methods and materials calls for caution in clinical decision-making. Notwithstanding these observations, clinicians have provided and continue to provide rehabilitative strategies for managing their patients' worn dentitions that range traditionally from extensive prosthodontics to an increasing reliance on adhesive techniques.

[Not Available]

Severe tooth wear is discussed from the perspective of appreciating the aetiologic background of the problem. A multifactorial basis is acknowledged for the extensively worn dentition and efforts to eliminate or minimize these underlying factors are important. The management of a case of severe incisal and occlusal wear can adopt different approaches. The author proposes the rationale and advantages for involving orthodontic preparation as part of the occlusal rehabilitation.