Periodontal repair in dogs: space-provision supports alveolar bone and cementum formation

Critical features of periodontal flaps with regard to blood clot stability: A review

BACKGROUND

Wound healing is a multifactorial procedure involving different cell types and biological mediators. The principles of wound healing are also applicable to periodontal tissues. The formation and stability of blood clots play a vital role in successful healing of wounds in periodontal tissues. The aim of the present review was to highlight the vital factors of periodontal flaps associated with blood clot stability.

HIGHLIGHT

The data on periodontal regeneration and wound healing have evolved greatly in light of several factors, including space for blood clots and blood clot stabilization. In periodontal osseous defects, the stability of blood clots seems critical to wound healing. If mechanical forces can be managed by wound stabilization, the gingival flap-tooth root interface may show connective tissue repair. However, compromised adhesion is susceptible to mechanical forces and can cause wound breakage and epithelialization.

CONCLUSION

The presence of a thick blood clot may hinder the plasmatic circulation between the recipient bed and graft during the initial stage of healing, which is critical in cases of mucogingival surgery. Root conditioning can also determine the healing consequence by enhancing blood clot adhesion.

Digital three-dimensional visualization of intrabony periodontal defects for regenerative surgical treatment planning

Background

In the regenerative treatment of intrabony periodontal defects, surgical strategies are primarily determined by defect morphologies. In certain cases, however, direct clinical measurements and intraoral radiographs do not provide sufficient information on defect morphologies. Therefore, the application of cone-beam computed tomography (CBCT) has been proposed in specific cases. 3D virtual models reconstructed with automatic thresholding algorithms have already been used for diagnostic purposes. The aim of this study was to utilize 3D virtual models, generated with a semi-automatic segmentation method, for the treatment planning of minimally invasive periodontal surgeries and to evaluate the accuracy of the virtual models, by comparing digital measurements to direct intrasurgical measurements.

Methods

Four patients with a total of six intrabony periodontal defects were enrolled in the present study. Two months following initial periodontal treatment, a CBCT scan was taken. The novel semi-automatic segmentation method was performed in an open-source medical image processing software (3D Slicer) to acquire virtual 3D models of alveolar and dental structures. Intrasurgical and digital measurements were taken, and results were compared to validate the accuracy of the digital models. Defect characteristics were determined prior to surgery with conventional diagnostic methods and 3D virtual models. Diagnostic assessments were compared to the actual defect morphology during surgery.

Results

Differences between intrasurgical and digital measurements in depth and width of intrabony components of periodontal defects averaged 0.31 ± 0.21 mm and 0.41 ± 0.44 mm, respectively. In five out of six cases, defect characteristics could not be assessed precisely with direct clinical measurements and intraoral radiographs. 3D models generated with the presented semi-automatic segmentation method depicted the defect characteristics correctly in all six cases.

Conclusion

It can be concluded that 3D virtual models acquired with the described semi-automatic segmentation method provide accurate information on intrabony periodontal defect morphologies, thus influencing the treatment strategy. Within the limitations of this study, models were found to be accurate; however, further investigation with a standardized validation process on a large number of participants has to be conducted.

Calcium phosphate barrier for augmentation of bone in noncontained periodontal osseous defects: a novel approach

AIM

The aim of this technique is to augment bone in non-contained osseous deformities using a unique self-sustaining calcium phosphate barrier.

INTRODUCTION

Bone has the inherent ability to regenerate completely if it is provided with a fracture space or an undisturbed enclosed scaffold. A secluded environment is essential as it provides a secured, sterile and stable wound system that regenerates lost bone by a process of osteopromotion. Reconstructive techniques using bone grafts and barrier membranes utilize this principle for augmentation of deficient bony sites by providing a closed environment that promotes clot stability, graft retention, and facilitates correct cell repopulation. However, in noncontained bone defects like one walled infrabony periodontal defect or sites with horizontal bone loss, regeneration of bone still remains an unrealistic situation since osseous topography at such sites does not favor membrane stability or bone grafts retention. This case report presents a promising technique to augment bone in areas with horizontal loss.

TECHNIQUE

Augmentation of bone in the interdental area with horizontal bone loss was accomplished by building a contained defect using a unique self sustaining calcium phosphate cement formulation. The calcium phosphate barrier stimulates the lost cortical plates and promotes graft retention and clot stability. At 6 months, there was a significant bone fill and trabecular formation in the interdental area and reduction in tooth mobility.

CONCLUSION

This promising technique could prove to be a good alternative to the conventional approaches for treating osseous deformities.

CLINICAL SIGNIFICANCE

Calcium phosphate is a promising barrier graft for repair of noncontained periodontal osseous defect. This technique cues both the clinicians and manufacturers to develop moldable tissue engineered constructs for osseous repair.