Effect of incisal preparation design on load-to-failure of ceramic veneers

Effect of a modified laminate veneer preparation design on absolute margin discrepancy and marginal overhang

STATEMENT OF PROBLEM

Veneer preparation designs impact veneer accuracy. However, whether a modified design could reduce absolute margin discrepancy and marginal overhangs is unclear.

PURPOSE

The purpose of this in vitro study was to investigate whether a modified veneer preparation design enhances the absolute margin discrepancy and marginal overhang.

MATERIAL AND METHODS

The absolute margin discrepancy and the marginal overhang of 3 different veneer preparation designs on a typodont tooth (n=20): feather edge, shoulder, and shoulder with wings were measured. The feather edge design was prepared first and subsequently modified to create the shoulder and shoulder with wings preparations. Ceramic veneers were fabricated using computer-aided design and computer-aided manufacture with each veneer assessed for fit before cementation. Ten specimens were cut vertically, and 10 were cut horizontally in each group. The absolute margin discrepancy and marginal overhangs were measured for each cross-section with scanning electron microscopy. Descriptive data analysis and hypothesis testing were conducted using the nonparametric Kruskal Wallis test (α=.05).

RESULTS

On the vertical sections, the shoulder with wings preparation had the best absolute margin discrepancy and overhang. The design was also best for mesial overhang and mesial absolute margin discrepancy when measuring horizontally.

CONCLUSIONS

The shoulder with wings preparation design produced the smallest cervical absolute margin discrepancy and overhang. This design also produced absolute margin discrepancy and overhangs comparable with those of the shoulder design in the proximal areas.

The ability of mouthguards to protect veneered teeth: A 3D finite element analysis

BACKGROUND/AIMS

Professional and amateur athletes might have veneer restorations. The aim of this study was to investigate the protective effect of mouthguards on veneered anterior restorations.

METHODS

A nonlinear dynamic analysis was performed to simulate conditions during an impact with or without a custom-made mouthguard. Using a computer-aided design (CAD) software, a slice of a human maxilla was designed containing an upper right central incisor. The model was composed of mucosa, cortical bone, trabecular bone, periodontal ligament, dentin, enamel, and pulp tissue. The enamel was prepared (feather design), restored with an indirect veneer (1.0 mm thickness), and duplicated to simulate both conditions with or without a mouthguard (4 mm thickness). Both models were subdivided into finite elements using the computer-aided engineering (CAE) software. Frictionless contacts were used, and an impact was simulated in which a rigid sphere hit the model at 1 m s^-1 . Fixation was defined at the base of the bone. The elastic modulus of the veneer was assessed by using five different restorative materials (resin composite, hybrid ceramic, zirconia-reinforced lithium silicate, lithium disilicate, and zirconia). Von Mises stress, minimal principal stress, and maximum principal stress (in MPa) were obtained and plotted for visual comparison.

RESULTS

Von-Mises results showed higher stress concentrations in the veneer's cervical labial region for models without a mouthguard. Observing the quantitative results for each model, the highest compressive (709 MPa) and tensile (58 MPa) stresses occurred in the situation without a mouthguard with a zirconia veneer, while the lowest occurred in resin composite veneer with a mouthguard (8 and 5 MPa). The mouthguard was able to reduce the stresses in the tooth structure and it also reduced the risk of fracture in all conditions.

CONCLUSIONS

Mouthguards were beneficial in reducing the effects of dental trauma regardless of the restorative material used to manufacture the indirect veneer, since they act by dampening the generated stresses during the trauma event. Equal impact stresses on a mouthguard will lead to higher stresses in veneered teeth with more rigid restorative materials leading to a less protective effect.

Thickness and yttria percentage influences the fracture resistance of laminate veneer zirconia restorations

OBJECTIVES

Mechanical properties are cardinal for the long-term clinical success of laminate veneer restorations but the selection of new restorative materials should ideally be based on clinical evidence, therefore, in vitro testing of dental materials is a good alternative to evaluate their properties and understand their behavior so this study aimed to compare and evaluate the effect of two different thicknesses and yttria percentage on the fracture resistance of laminate veneer zirconia restorations.

MATERIALS AND METHODS

Forty laminate veneer restoration prepared from partial sintering zirconia of 3Y (yttria), 5Y (yttria), combined 3Y&5Y (yttria), and lithium disilicate. Specimens were assigned into four main groups according to their percentage of yttria content (n = 10) and subgrouped into two thicknesses (0.5 mm thickness and 0.3 mm thickness) (n = 5) as follows: Group I, II, III, and IV (Group I for lithium disilicate (control), Group II for 3Y zirconia, Group III for 5Y zirconia, and Group IV for combined 3Y&5Y zirconia), each of them subdivided according to their thickness into two subgroups (n = 5 for each one) and resistance to fracture for each restoration was evaluated using a universal testing machine. Data were analyzed using a one-way analysis of variance and Duncan's tests at a 5% level of significance.

RESULTS

The thickness of laminate veneer restoration significantly affects the fracture resistance value of all type of laminate veneers restorations (fracture resistance mean value was highest for 0.5 mm thickness and lower for 0.3 mm thickness restorations) and yttria percentage significantly affect fracture resistance value of zirconia laminate veneer restorations (fracture resistance mean value was highest for 0.5 mm thickness of 3Y zirconia [865 N] and combined 3Y&5Y zirconia [846 N]).

CONCLUSIONS

Reducing the thickness of laminate zirconia veneer restorations to 0.3 mm reduces its fracture resistance and increasing yttria percentage had an adverse effect on fracture resistance of zirconia laminate veneer restorations.

Stress distribution within the ceramic veneer-tooth system with butt joint and feathered edge incisal preparation designs

OBJECTIVE

This in-vitro study aims to study the stress distribution within the ceramic veneer-tooth system with two incisal preparation designs-butt joint (BJ) and feathered edge (FE), and to correlate these findings to the results of our previous published load-to-failure study.

METHODS

Six photoelastic models were fabricated with an epoxy resin material (West System 105 Epoxy Resin/205 Fast Hardener, West System) to represent BJ and FE preparation configurations at 0° and 20° loading angulations. Lithium disilicate ceramic veneers (IPS e.max CAD, Ivoclar Vivadent) were bonded to the BJ and FE photoelastic models using resin cement (IPS Variolink Esthetic, Ivoclar Vivadent). Each model was loaded using an Instron Universal Testing Machine at the incisal edge at a cross-head speed of 0.25 mm/min till 100 N.

RESULTS

BJ photoelastic model had more uniform distribution compared with FE photoelastic models under 0° and 20° loading angulations.

CONCLUSION

Parallel to the results of our earlier load-to-failure published study, both incisal preparation designs affect stress distribution within the ceramic veneer-tooth system. BJ photoelastic model demonstrated a more uniform distribution compared with FE photoelastic model.

CLINICAL SIGNIFICANCE

BJ incisal preparation design has more uniform stress distribution than FE preparation design within the ceramic veneer-tooth system.