Effect of configuration factor on gap formation in hybrid composite resin, low-shrinkage composite resin and resin-modified glass ionomer

Application and limitations of configuration factor (C-factor) in stress analysis of dental restorations

OBJECTIVE

The configuration factor (C-factor) is an index used to evaluate the relationship between cavity configuration and the development of polymerization shrinkage stress in dental restorations. Although C-factor has been widely researched, its correlation with stress analysis in dental restorations remains controversial. This review aims to discuss the application and limitations of C-factor and define the restricted conditions under which the C-factor "rule of thumb" is applicable.

METHODS

A thorough literature review was conducted on the application and limitations of C-factor in stress analysis of dental restorations. This was principally based on MEDLINE/PubMed and Web of Science databases and a review of the relevant studies and publications in scientific papers in international peer-reviewed journals for the specific topic of C-factor and polymerization shrinkage.

RESULTS

The C-factor alone cannot provide an accurate prediction of the shrinkage stress of restorations and the mechanical behavior of material-tooth interfaces. C-factor is only applicable under one condition not typically seen in clinical practice: low, near-rigid compliance.

SIGNIFICANCE

Conditions for the application of C-factor have been explicitly defined. A more accurate and precise understanding and utilization of the C-factor is of benefit as it contributes to better understanding of polymerization shrinkage behavior of restorations.

Shrinkage Stress and Temperature Variation in Resin Composites Cured via Different Photoactivation Methods: Insights for Standardisation of the Photopolymerisation

The literature has shown that there is no consensus regarding the best resin composite photoactivation protocol. This study evaluated the efficiency of the conventional, soft-start, pulse-delay and exponential protocols for photoactivation of resin composites in reducing the shrinkage stress and temperature variation during the photopolymerisation. The photoactivation processes were performed using a photocuring unit and a smartphone app developed to control the irradiance according each photoactivation protocol. These photoactivation methods were evaluated applying photoactivation energies recommended by the resins manufactures. Three brands of resin composites were analysed: Z-250, Charisma and Ultrafill. The cure effectiveness was evaluated through depth of cure experiments. All results were statistically evaluated using one-way and multi-factor analysis of variance (ANOVA). The use of exponential and pulse-delay methods resulted in a significant reduction of the shrinkage stress for all evaluated resins; however, the pulse-delay method required too long a photoactivation time. The increases on the temperature were lower when the exponential photoactivation was applied; however, the temperature variation for all photoactivation protocols was not enough to cause damage in the restoration area. The evaluation of the depth of cure showed that all photoactivation protocols resulted in cured resins with equivalent hardness, indicating that the choice of an alternative photoactivation protocol did not harm the polymerisation. In this way, the results showed the exponential protocol as the best photoactivation technique for practical applications.

The Silorane-based Resin Composites: A Review

This article aims to review the research done on the silorane-based resin composites (SBRC) regarding polymerization shrinkage and contraction stresses and their ability to improve the shortcomings of the methacrylate-based resin composites (MRBC). Special attention is given to their physical and mechanical properties, bond strength, marginal adaptation, and cusp deflection. The clinical significance of this material is critically appraised with a focus on the ability of SBRC to strengthen the tooth structure as a direct restorative material. A search of English peer-reviewed dental literature (2003-2015) from PubMed and MEDLINE databases was conducted with the terms "low shrinkage" and "silorane composites." The list was screened, and 70 articles that were relevant to the objectives of this work were included.

Five second photoactivation? A microhardness and marginal adaptation in vitro study in composite resin restorations

INTRODUCTION

Studies defining the characteristics of light curing units and photoactivation methods are necessary to allow the correct choices to be made in daily practice. This study aimed to determine whether different photoactivation protocols for composite resins [periodic level shifting (PLS) - 5 second and soft-start] are able to maintain or enhance the mechanical properties and marginal adaptation of restorations.

METHODS

Restorations were placed in bovine teeth using the following photoactivation methods: continuous light for 20 seconds (control group); PLS technology (PLS - 5 second group); and continuous light and a light guide tip distance of 6 mm after which the tip was placed at the surface of the restoration (soft-start group). The teeth were transversely sectioned in the incisal-cervical direction. Thirty halves were randomly selected for Knoop microhardness testing (n = 10). The other 30 halves were subjected to scanning electron microscopy analysis. The images obtained were measured to identify the highest marginal gap, and statistical tests for variance analysis were conducted.

RESULTS

Microhardness tests showed no statistically significant difference between the photoactivation methods analysed (P ≥ 0.01). The tests showed a difference among depths (P < 0.01), with the deeper layers being the hardest. In analysing marginal adaptation, no significant difference was identified between the higher marginal gap values in the continuous (mean = 10.36) and PLS - 5 second (mean = 10.62) groups, and the soft-start group (mean = 5.83) presented the lowest values (P < 0.01).

CONCLUSIONS

The PLS - 5 second and soft-start protocols did not alter the hardness of the restorations. Moreover, the PLS - 5 second protocol did not alter the marginal adaptation, whereas the soft-start protocol improved marginal adaptation.

Refractive indices of unfilled resin mixtures and cured composites related to color and translucency of conventional and low-shrinkage composites

This study correlated the refractive indices (RIs) of unfilled resin mixtures and resin-based composites (RBCs) with color and translucency of conventional and low-shrinkage RBCs. Unfilled resin mixtures based on different ratios of conventional monomers Bisphenol A-glycidyl-methacrylate (BisGMA)/triethyleneglycol-dimethacrylate (TEGDMA) and urethane-dimethacrylate (UDMA)/TEGDMA and a low-shrinkage monomer FIT-852 (FIT, Esstech Inc.)/TEGDMA were used to prepare model RBCs, containing 30 wt % of the organic matrix and 70 wt % of silanated barium-glass fillers (n = 1.553, Esstech Inc.). The RIs of resins were measured on an ABBE refractometer, those of cured RBCs using the Becke-line method in immersion oils. Color and translucency were determined using an AvaSpec-2048 (Avantes BV) spectrometer. The RIs of unfilled resin mixtures decreased with increasing amounts of TEGDMA. Cured RBCs had higher RIs than their respective resin mixtures. BisGMA-based composites were more translucent with significantly lower L* values than FIT- and UDMA-based RBCs. The RIs of unfilled resins positively correlated with cured RBCs (p = 0.001), as did the RIs with translucency (p = 0.001) and color (p = 0.008). Resin mixtures and corresponding RBCs based on UDMA and its modified low-shrinkage version, FIT, showed similar optical properties. The RIs of unfilled resins appeared to be good predictors of the RIs of cured RBCs. © 2015 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 105B: 7-13, 2017.