A practice-based clinical evaluation of the survival and success of metal-ceramic and zirconia molar crowns: 5-year results

Influence of different cutting instruments and rotational speeds on heat generation and cutting efficiency when sectioning different types of zirconia

PURPOSE

The purpose of this study was to evaluate the temperature generated on the intaglio surface and efficiency when cutting different types of zirconia with different rotary instruments and rotational speeds.

METHODS

A conventional diamond rotary instrument (Brasseler, grit size 107 μm) and special diamond rotary instrument marketed to cut zirconia (4 ZR, Brasseler, grit size 126 μm) were tested on 3Y-TZP and 4Y-TZP zirconia with a rotation speed of 100,000 rpm and 200,000 rpm. Zirconia specimens were cut under water cooling (110 mL/min) in a custom-made holder attached to a universal testing machine. The temperature was recorded with infrared sensors pointing at the intaglio surface of the zirconia specimens.

RESULTS

A rotation speed of 200,000 rpm resulted in significantly shorter cutting times, but also in significantly higher temperatures at the intaglio surface of the zirconia specimens compared with a rotation speed of 100,000 rpm. Significantly shorter cutting times were observed for the conventional diamond rotary instrument than for the special rotary instrument marketed to cut zirconia. Using the special rotary instrument, significantly longer cutting times were recorded for 3Y-TZP than for 4Y-TZP.

CONCLUSIONS

A conventional diamond rotary instrument was more efficient than a special rotary instrument. However, to avoid high temperatures when cutting zirconia clinically, a rotation speed of 100,000 rpm is recommended.

Evaluation of Microleakage Using Different Luting Cements in Kedo Zirconia Crowns: An In Vitro Assessment

Introduction A space between the prepared tooth and the cemented crown can cause microleakage, allowing microorganisms to enter, which in turn leads to the breakdown of the luting cement. To achieve an optimum fit, several factors should be considered, including the type of crown used, the taper of tooth preparation, and the type of cementing agent. Aim The purpose of the current study is to evaluate the microleakage of zirconia crowns cemented with glass ionomer cement (GIC), resin-modified GIC (RMGIC), and self-adhesive resin cement. Materials Forty-five primary mandibular molars were divided into three groups: Group I receiving GIC, Group II receiving RMGIC, and Group III receiving self-adhesive resin cement. These cements were used to lute the teeth with Kedo zirconia crowns. The restored samples underwent thermal cycling and were assessed for microleakage under a stereomicroscope. For the statistical analysis, SPSS version 23.0 was used. Descriptive statistics were presented as frequencies and percentages. Analytical statistics, including the Mann Whitney U test, were used to assess the differences in the level of microleakage between the groups at p < 0.05. Results The Mann Whitney U test revealed no significant difference in the level of microleakage between GIC and RMGIC (p = 0.072). However, self-adhesive resin cement showed significantly less microleakage than GIC (p = 0.000). Similarly, when comparing RMGIC and self-adhesive resin cement, the latter showed significantly less microleakage than the former (p = 0.001). Conclusion Microleakage of Kedo zirconia crowns on mandibular first molars was highest when luted with GIC, followed by RMGIC, and was least when luted with self-adhesive resin cement.

Clinical evaluation of zirconia crowns cemented with two different resin cements: A retrospective study

BACKGROUND

Self-adhesive resin cement has been used extensively with zirconia crowns. Several in vitro studies showed that adhesive resin cementation may increase zirconia crowns' retention and their fatigue resistance.

OBJECTIVES

This retrospective study aimed to evaluate the clinical performance, survival and success rates and complications encountered with zirconia crowns cemented with two different self-adhesive resin cements.

METHODS

A total of 112 patients who received 176 monolithic zirconia crowns were evaluated. Crowns were cemented with RelyX Unicem 2 (n = 74) and Panavia SA (n = 102) self-adhesive resin cements. Clinical assessments of the crowns and supporting periodontal structures were performed following the modified California Dental Association (CDA) criteria. Intraoral photographs and periapical and bitewing radiographs were obtained for further assessment by two evaluators. Descriptive statistics, McNemar, t-test, log rank (Mantel-Cox) tests and Kaplan-Meier survival analyses were performed (a = .05).

RESULTS

The 5-year survival and success rates were 100% and 96.4%, respectively. The complications encountered were recurrent caries (2.2%) and the need for endodontic treatment (0.5%). No technical complications, such as fracture or loss of retention, were observed. The type of cement and patient-related factors did not influence the survival and success rates of the crowns.

CONCLUSIONS

Survival rate of zirconia crowns cemented with two different self-adhesive resin cements was 100% after 5 years.

Reliability and lifetime of lithium disilicate, 3Y-TZP, and 5Y-TZP zirconia crowns with different occlusal thicknesses

OBJECTIVES

To assess the probability of survival of crowns made with a 3Y-TZP, a 5Y-TZP, and a lithium disilicate.

MATERIALS AND METHODS

CAD-CAM premolar crowns with occlusal thicknesses of 1.0 mm or 1.5 mm and cemented on a metal dye. Step-stress accelerated life testing (SSALT) was performed to access the use level probability Weibull curves and reliability were calculated for the completion of a mission of 100,000 cycles at 300 to 1200 N.

RESULTS

All ceramics showed a high probability of survival (87-99%) at 300 N, irrespective of thickness. 3Y-TZP shows no significant decrease in the probability of survival up to 1200 N (83-96%). Lithium disilicate presented lower reliability than zirconia under the 600 N mission. 5Y-TZP showed lower reliability than 3Y-TZP at 1200 N. There was no significant difference in the Weibull modulus (3.23-7.12). 3Y-TZP had the highest characteristic strength (2483-2972 N), followed by 5Y-TZP (1512-1547 N) and lithium disilicate (971-1154 N).

CONCLUSION

Zirconia ceramics have a high probability of survival (up to 900 N-load), while lithium disilicate survives up to 300 N load only, irrespective of the thickness (1.0 mm or 1.5 mm).

CLINICAL RELEVANCE

The probability of survival of posterior crowns made with zirconia ceramics resists extreme loads while glass ceramics resist normal chewing loads. In addition, crowns with thinner occlusal face showed sufficient mechanical behavior.

Six-year clinical performance of lithium disilicate glass-ceramic CAD-CAM versus metal-ceramic crowns

PURPOSE

To assess the clinical performance of monolithic CAD-CAM lithium disilicate glass-ceramic (LDGC) crowns and metal-ceramic (MC) crowns provided by predoctoral students. This study also assessed the effects of patient and provider-related factors on their clinical performance as well as patient preference for these types of crowns.

MATERIALS AND METHODS

Twenty-five patients who received 50 crowns (25 LDGC CAD-CAM and 25 MC) provided by predoctoral students were retrospectively examined. LDGC CAD-CAM crowns were milled in-house using the CEREC Bluecam system and cemented with either RelyX Unicem or Calibra Esthetic resin cements. MC crowns were cemented with RelyX Unicem cement. Clinical assessment of the crowns and the supporting periodontal structures were performed following the modified California Dental Association (CDA) criteria. Patients' preference was recorded using a visual analog scale (VAS). The results were statistically analyzed using log-rank test, Pearson Chi-squared test and Kaplan-Meier survival analysis.

RESULTS

Twelve complications were observed in the MC crown group (9-esthetic, 2-technical and 1-biological). In comparison, 2 complications in the LDGC CAD-CAM crown group were observed (1-technical and 1-esthetic). The 6-year cumulative survival rates for MC crowns and LDGC CAD-CAM were 90.8% and 96%, respectively, whereas the success rates were 83.4% and 96%, respectively. Overall, patients preferred the esthetic outcomes of LDGC CAD-CAM crowns over MC crowns.

CONCLUSION

The high survival and success rates, low number of complications, and the high level of patients' acceptance of monolithic LDGC CAD-CAM crowns lend them well as predictable and viable alternatives to the "gold standard" MC crowns.

Potential complications of CAD/CAM-produced resin composite crowns on molars: A retrospective cohort study over four years

Purpose

Evaluation of the clinical performance of computer-aided design/computer-aided manufacturing-produced resin composite crowns (CAD/CAM composite crowns) on molars with a particular focus on placement location.

Methods

A retrospective cohort study was performed based on the clinical records of patients with CAD/CAM composite crowns on molars (June 2016 to March 2021). The hazard ratios (HRs) and 95% confidence intervals (95% CIs) were estimated based the Cox proportional hazard model to evaluate the effect of tooth location on complication type and occurrence. Covariates included crown location (maxilla/mandible, distalmost tooth/not distalmost tooth, and first molar/second or third molar) and endodontically treated (nonvital) or untreated (vital) tooth.

Results

Overall, 362 crowns were evaluated (mean follow-up: 378 days, median: 286 days), and 106 crowns (29.3%) showed complications, most frequently crown debonding. The cumulative success and survival rates were 70.9% and 93.7%, respectively, after 1 year and 49.5% and 86.5%, respectively, after 3 years. There was no significant difference in the HRs and log-rank tests in the Kaplan–Meier curves based on crown location parameters (P > 0.05). However, placement on vital teeth was associated with higher risks than on nonvital teeth (HR, 1.55; 95% CI, 1.03–2.23). In addition, the cement as a covariate yielded a high HR.

Conclusions

The location of CAD/CAM composite molar crowns is unlikely a risk factor for complications; therefore, these crowns can be clinically applied to all molars. However, the application of such molar crowns to vital teeth and the use of a cement other than adhesive resin cement present risks.

Metal-ceramic and porcelain-veneered lithium disilicate crowns: a stress profile comparison using a viscoelastic finite element model

Metal-ceramics (MC) are one of the oldest dental restorative systems, which are considered to be the gold standard for full crown restoration. Porcelain-veneered lithium disilicate (PVLD), on the other hand, are newer material systems that have shown high survival rate in clinical follow-ups but needs to be studied more. This study compares the stresses developed in the single crowns made from newer PVLD system against those with MC configuration. For this comparison, influence of the layer thickness and cooling rates is also taken into consideration. An experimentally validated viscoelastic finite element model (VFEM) has been developed to predict the stress profile in these systems. Three-dimensional rotationally symmetric crowns were analyzed using this validated model for both material systems, three veneer to core thickness ratios (2:1, 1:1, 1:2), and two cooling rates: slow cooling at 1.74E-5 W/mm2K (∼30 K/min) and fast cooling at 1.74E-4 W/mm2K (∼300 K/min). PVLD showed lower values of transient and residual stresses than MC. The maximum tensile residual stresses in MC systems were observed in the cusp area, whereas those in PVLD were located in the central fossa. With the reduction in veneer layer, there was reduction in residual stress in MC; however, the veneer thickness had little to no effect in PVLD. The effect of cooling rate was also evident as slow cooling resulted in lower residual and tensile stresses for both material systems.

Five-year clinical performance of monolithic and partially veneered zirconia single crowns-a prospective observational study

PURPOSE

The purpose of this study was to prospectively evaluate the medium-term clinical performance and esthetics of monolithic and partially (i.e., facially) veneered zirconia single crowns (MZ-SC and PZ-SC, respectively).

METHODS

Between September 2011 and June 2013, 68 participants received 90 MZ-SC and 72 PZ-SC. Clinical study documentation was performed at crown cementation (baseline), at 6-month follow-up, and then yearly thereafter using standardized report forms. Three participants with four MZ-SC dropped out during clinical follow-up. Thus, 65 participants (n = 31, 47.7% men) fitted with 158 restorations (86 MZ-SC, 72 PZ-SC) were evaluated. The mean observation period of the restorations was 5.8 ±2.5 years; 6.3 ±2.2 for MZ-SC and 5.2 ±2.6 for PZ-SC.

RESULTS

The 5-year rate of complication-free survival (success) was 87.0% for MZ-SC and 95.8% for PZ-SC (log-rank test, p = 0.026). The 5-year failure-free survival rate was 93.1% for MZ-SC and 96.2% for PZ-SC (log-rank test, p = 0.111), and the 5-year ceramic fracture-free survival rate was 100% for MZ-SC and 98.6% for PZ-SC (log-rank test, p = 0.274). Crowns of both designs were awarded excellent scores for esthetics by participants and dentists.

CONCLUSIONS

Monolithic and partially veneered zirconia crowns can be used clinically with high medium-term survival and success and uncompromised esthetic results.

Residual stresses explaining clinical fractures of bilayer zirconia and lithium disilicate crowns: A VFEM study

OBJECTIVE

To understand the stress development in porcelain-veneered zirconia (PVZ) and porcelain-veneered lithium disilicate (PVLD) crowns with different veneer/core thickness ratios and cooling rates. To provide design guidelines for better performing bilayer restorations with the aid of Viscoelastic Finite Element Method (VFEM).

METHODS

The VFEM was validated by comparing the predicted residual stresses with experimental measurements. Then, the model was used to predict transient and residual stresses in the two bilayer systems. Models with two different veneer/core thickness ratios were prepared (2:1 and 1:1) and two cooling protocols were simulated (Fast: ∼300 °C/min, Slow: ∼30 °C/min) using the heat transfer module, followed by stress analysis in ABAQUS. The physical properties of zirconia, lithium disilicate, and the porcelains used for the simulations were determined as a function of temperature.

RESULTS

PVLD showed lower residual stresses than PVZ. The maximum tensile stresses in PVZ were observed in the cusp area, whereas those in PVLD were located in the central fossa. The 1:1 thickness ratio decreased stresses in both layers of PVZ. Slow cooling slightly decreased residual stresses in both systems. However, the cooling rate effect was more evident in transient stresses.

SIGNIFICANCE

Slow cooling is preferable for both systems. A thinner porcelain layer over zirconia lowers stresses throughout the restoration. The different stress distributions between PVZ and PVLD may affect their failure modes. Smaller mismatches in modulus, CTE, and specific heat between the constituents, and the use of low T_g porcelains can effectively reduce the deleterious transient and residual tensile stresses in bilayer restorations.

Long-term clinical performance and complications of zirconia-based tooth- and implant-supported fixed prosthodontic restorations: A summary of systematic reviews

OBJECTIVES

To present an overview on systematic reviews on prosthodontic zirconia restorations and to discuss long-term complications as well as information on anatomical and functional changes to the masticatory system.

DATA/SOURCES

MEDLINE, EMBASE, Trip medical, and Cochrane Library databases were searched for systematic reviews up to February 2021. Bias was assessed and clinical survival and complications were analyzed.

STUDY SELECTION

38 eligible articles published between 2006 and 2021 were included. The reviews were based on 128 in vivo studies on approximately 10,000 zirconia restorations. 5-year cumulative survival rates varied between 91.2% and 95.9% for tooth-supported (TS) single crowns (SC), 89.4% and 100% for TS multi-unit fixed dental prostheses (FDP), 97.1% and 97.6% for implant-supported (IS) SCs and 93.0% and 100% for IS FDPs. Chipping was the most often technical complication, followed by framework fracture, loss of retention, marginal discrepancies/discoloration, occlusal roughness and abutment/screw loosening. Color mismatch was the only esthetic complication. Biological complications were caries, endodontic complications, tooth fracture, periodontal disease, abrasion/attrition, persisting pain, high sensitivity, peri‑implantitis and soft tissue issues. Patients with bruxism were only examined sporadically.

CONCLUSIONS

5-year results for zirconia restorations were satisfactory. The predominant technical problem of veneering fractures could be overcome with adapted design or fabrication and application of monolithic restorations, but reviews of clinical studies on this subject are rare. The impact of zirconia restorations on the masticatory system remains unclear.

CLINICAL SIGNIFICANCE

Zirconia restorations are experiencing a rapidly increasing use in dental practice. Being highly wear-resistant, hard and durable, it can be assumed that they do not follow natural abrasion and changes in the masticatory system. Possible long-term effects on the stomatognathic system as a whole should therefore be considered.

Extended glaze firings for porcelain-veneered zirconia: Effects on the mechanical and optical behavior

OBJECTIVE

This study evaluated the effect of dwell time (conventional or extended) and cooling protocol (fast or slow) of self-glaze firings on the mechanical (flexural strength and crack propagation) and optical (color and translucency) properties of a porcelain-veneered zirconia system.

METHODS

Bilayer disc-shaped samples were prepared (Vita VM9 + In-Ceram YZ) and divided according to the final thermal treatment: glaze firing followed by slow cooling (furnace opening at 200 °C) (G-S) or fast cooling (furnace opening at 600 °C) (G-F, manufacturer-recommended protocol), extended glaze firing (15 min of dwell time) followed by slow cooling (EG-S) or fast cooling (EG-F), or no thermal treatment (CTRL). Porcelain roughness (Ra and Rz) was measured before and after glaze firings. Color (ΔE₀₀) and translucency (TP₀₀) alteration were also evaluated. Flexural strength was measured with the piston-on-three-ball test and crack propagation analysis was performed after Vickers indentations. Complementary analyzes of crystalline phase and scanning electron microscopy were carried out.

RESULTS

Significant effect of dwell time was observed, with extended glaze leading to higher flexural strength and shorter crack lengths. Cracks of EG groups were observed to end in clusters of crystals. Color and translucency changed below perceptibility thresholds. All treatments led to a smoother surface and EG groups reached the lowest Rz values. An extra SiO₂ peak was revealed in control and EG groups. No effect of cooling protocol was found.

SIGNIFICANCE

Extended glaze firing was able to improve the resistance to crack initiation and propagation of porcelain-veneered zirconia without clinically perceptible changes in optical properties.

Treatment options for large posterior restorations: a systematic review and network meta-analysis

BACKGROUND

The best treatment option for large caries in permanent posterior teeth is still a matter of uncertainty in dental literature. The authors conducted a network meta-analysis to address the challenges related to rehabilitation of these teeth.

TYPES OF STUDIES REVIEWED

The authors selected prospective and retrospective studies that compared at least 2 different treatment alternatives for permanent teeth with a minimum of 5 years of follow-up. The authors searched databases from MEDLINE, Scopus, Cochrane Library, and Web of Science in October 2019 without language or year of publication restrictions.

RESULTS

From 11,263 studies identified, 43 studies fulfilled the eligibility criteria and were included in the final review. Only 13 studies were randomized controlled trials and were classified as low risk of bias. Gold (annual failure rate of 0.29%) and metal ceramic (annual failure rate of 0.52%) crowns performed better for indirect restorations and direct resin composite performed better for direct restorations (annual failure rate of 2.19%). The most substantial comparisons were between feldspathic and glass ceramics, followed by direct resin composite and amalgam; there were no statistically significant differences between these interventions. Results of the pairwise meta-analysis showed mainly glass ionomer as significantly more prone to failure than amalgam and direct composite resin.

CONCLUSIONS AND PRACTICAL IMPLICATIONS

Reference standard direct and indirect materials except for glass ionomer can be used for restorations of large posterior caries.

CAD/CAM or conventional ceramic materials restorations longevity: a systematic review and meta-analysis

PURPOSE

This systematic review and meta-analysis aimed to evaluate the difference in longevity of tooth-supported ceramic prostheses designed by conventional and computer-aided design/computer-aided manufacturing (CAD/CAM) techniques.

STUDY SELECTION

Two reviewers searched the Web of Science, PubMed, SCOPUS and LILACS databases between 1966 and October 2017. Clinical studies that compared the survival rate of CAD/CAM against conventional restorations were included.

RESULTS

Eleven randomized controlled trials and three prospective studies were included, n=14. Three types of tooth-supported restorations were searched in the included studies: single crown, multiple-unit and partial ceramic crown. The follow-up of patients in the studies ranged from 24 to 84 months. A total of 1209 restorations had been placed in 957 patients in the included trials, and failures were analyzed by type and material restoration. From a total of 72 restoration failures, the CAD/CAM system resulted in a 1.84 (IC95%: 1.28-2.63) higher risk than conventional manufacturing of ceramic restoration. Nevertheless, when drop-outs were included as a failure risk, the CAD/CAM system resulted in a risk of 1.32 (IC95%: 1.10-1.58). Multilevel analysis of tooth-supported ceramic restorations, considering drop-outs as successes, resulted in rates of 1.48 and 2.62 failures per 100 restoration-years for the controls and CAD/CAM groups, respectively. Considering drop-outs as failures, we found rates of 4.23 and 5.88 failures per 100 restoration-years for the controls and CAD/CAM groups, respectively.

CONCLUSIONS

The meta-analysis results suggest that the longevity of a tooth-supported ceramic prostheses made by CAD/CAM manufacturing is lower than that of crowns mad by the conventional technique.

A possible risk of CAD/CAM-produced composite resin premolar crowns on a removable partial denture abutment tooth: a 3-year retrospective cohort study

PURPOSE

To evaluate the early performance of computer-aided design/computer-aided manufacturing (CAD/CAM)-produced composite resin crown (CAD/CAM composite crown) treatment on premolars, specifically, placement on a removable partial denture (RPD) abutment tooth, and the distalmost tooth in the dental arch, as possible clinical risk factors.

METHODS

A retrospective cohort study (April 2014 to July 2017) was performed utilizing the clinical records of patients who received a premolar CAD/CAM composite crown treatment. The variables of time of treatment for (1) successful crowns (complication event-free) and (2) surviving crowns (clinically functional including re-luted) were estimated using Kaplan-Meier analysis. Survival distributions regarding "RPD abutment tooth" and "distalmost tooth" were analyzed with the log-rank test. Multilevel survival analyses were used to identify hazard ratios and associated risk factors.

RESULTS

Five hundred and forty-seven crowns were evaluated (mean follow-up time 1.3±0.9years) in 327 patients. A total of 87 crowns had at least one complication, with loss of crown retention being the most common (70 crowns). Estimated success and survival rates at 3 years were 71.7% and 96.4%, respectively. The risk of complications was significantly higher for an RPD abutment tooth than for a non-RPD abutment tooth. There was no significant difference between the distalmost tooth and non-distalmost tooth in the dental arch.

CONCLUSIONS

The demonstrated complication rate for CAD/CAM composite crowns placed on premolars was 15.9% over a period of up to 3 years. There was a substantial risk of complications with placement of such a crown on an RPD abutment tooth.

An Interdisciplinary Approach for Hypoplastic Amelogenesis Imperfecta: A Case Report

Introduction:

Generally, the appropriate rehabilitation concepts of patients with Amelogenesis Imperfecta (AI) should include a multidisciplinary treatment approach.

Case Report:

This case report describes full mouth rehabilitation of a patient with AI. A 20 years old woman was referred to our clinic with a chief complaint of tooth discoloration, diastema, unsatisfactory esthetics and slight tooth sensitivity. Clinical, histological and radiographic examination revealed hypoplastic AI. Short crowns, diastema, occlusal wear with exposed dentin in the posterior areas, the lack of contact points, dental caries and discoloration were the other clinical findings.

Results:

As a result of the periodontal and prosthetic evaluation, gingivectomy and ostectomy were planned, and they followed a full mouth fixed prosthetic restoration.

Conclusion:

There was no complication or complaint in a 3-year follow-up. At the end of this follow-up period, the patient was satisfied with esthetics, function and phonation properties of her prostheses.

CAD/CAM Ceramic Restorative Materials for Natural Teeth

Advances in computer-aided design (CAD) / computer-aided manufacturing (CAM) technologies and their ease of application enabled the development of novel treatment concepts for modern prosthodontics. This recent paradigm shift in fixed prosthodontics from traditional to minimally invasive treatment approaches is evidenced by the clinical long-term success of bonded CAD/CAM glass-ceramic restorations. Today, defect-oriented restorations, such as inlays, onlays, and posterior crowns, are predominately fabricated from glass-ceramics in monolithic application. The variety of CAD/CAM ceramic restorative systems is constantly evolving to meet the increased demands for highly aesthetic, biocompatible, and long-lasting restorations. Recently introduced polymer-infiltrated ceramic network CAD/CAM blocks add innovative treatment options in CAD/CAM chairside 1-visit restorations. The material-specific high-edge stability enables the CAD/CAM machinability of thin restoration margins. Full-contour zirconia restorations are constantly gaining market share at the expense of bilayered systems. Advancements in material science and bonding protocols foster the development of novel material combinations or fabrication techniques of proven high-strength zirconia ceramics. CAD/CAM applications offer a standardized manufacturing process resulting in a reliable, predictable, and economic workflow for individual and complex teeth-supported restorations. More evidence from long-term clinical studies is needed to verify the clinical performance of monolithic polymer-infiltrated ceramic network and zirconia teeth-supported minimally invasive and extensive restorations.

Survival rate of modern all-ceramic FPDs during an observation period from 2011 to 2016

PURPOSE

In literature, many studies compare survival rates of different types of FPDs. Most of them compared restorations, which originated from one university, but from different clinicians. Data about restoration survival rates by only one experienced dentist are very rare. The aim of this study was to evaluate the survival rate of allceramic FPDs without the blurring effects of different clinicians.

MATERIALS AND METHODS

153 veneeredzirconia FPDs were observed for follow-up. 22 patients received 131 single crowns and 22 bridges. Because of the different bridge lengths, one unit was defined as a restored or replaced tooth. In total, 201 units were included. Only the restorations performed by the same clinician and produced in the same dental laboratory from 2011 to 2016 were included. Considered factors were defined as “type of unit”, “type of abutment”, “intraoral region”, and “vitality”. Modified UHPHS criteria were used for evaluation. Statistical analysis was performed using cox-regression.

RESULTS

189 units (94.0%) showed no kind of failure. 5 chippings (2.4%) could be corrected by intraoral polishing. 4 units (1.9%) exhibited spontaneous decementation. These polishable and recementable restorations are still in clinical use. Chippings or decementations, which lead to total failure, did not occur. One unit was completely fractured (0.5 %). Biological failures (caries, periodontitis or periimplantitis) did not occur. The statistical analysis of the factors did not reveal any significant differences.

CONCLUSION

Modern all-ceramic FPDs seem to be an appropriate therapy not only for single restorations but for complex occlusal rehabilitations.

Longevity of metal-ceramic crowns cemented with self-adhesive resin cement: a prospective clinical study

Resin cements are often used for single crown cementation due to their physical properties. Self-adhesive resin cements gained widespread due to their simplified technique compared to regular resin cement. However, there is lacking clinical evidence about the long-term behavior of this material. The aim of this prospective clinical trial was to assess the survival rates of metal-ceramic crowns cemented with self-adhesive resin cement up to six years. One hundred and twenty-nine subjects received 152 metal-ceramic crowns. The cementation procedures were standardized and performed by previously trained operators. The crowns were assessed as to primary outcome (debonding) and FDI criteria. Statistical analysis was performed using Kaplan-Meier statistics and descriptive analysis. Three failures occurred (debonding), resulting in a 97.6% survival rate. FDI criteria assessment resulted in scores 1 and 2 (acceptable clinical evaluation) for all surviving crowns. The use of self-adhesive resin cement is a feasible alternative for metal-ceramic crowns cementation, achieving high and adequate survival rates.

Prognostic factors of single-visit endodontic and restorative treatment under general anaesthesia for special needs patients

The aim of this study was to evaluate the longevity of teeth with single-visit endodontic and restorative treatment under general anaesthesia (GA) for special needs patients and to investigate factors associated with survival and success. Data were collected from 381 teeth in 203 patients [mean (s.d.) age = 27·0 (14·1)]. All endodontic and restorative procedures were performed during a single GA session except for cementation of crowns in the cases requiring crown restoration (38%). A total of 267 teeth (70·6%) were followed-up for 6-81 months [mean (s.d.): 32·7 (20·0)]. Patients and teeth with and without follow-up were compared. Kaplan-Meier analysis with generalised Wilcoxon test was used to compare the mean survival and success period. Cox proportion hazard regression model was applied for multivariate analysis. At the end of the observation period, 10 teeth had a crown fracture (5-year survival rate = 89·8%), and an additional 10 teeth had primary or secondary caries (5-year success rate = 86·4%). Risk factors associated with survival were age (>40), non-parental caregiver, cooperation level and periodontal disease. A soft diet was an additional risk factor against the success of teeth. Single-visit endodontic and restorative treatment under GA showed favourable outcomes, suggesting a promising treatment option for special needs patients. Patient- and dental-specific circumstances need to be carefully considered to enhance the longevity of reconstructed teeth.

Zirconia in biomedical applications

INTRODUCTION

The use of zirconia in medicine and dentistry has rapidly expanded over the past decade, driven by its advantageous physical, biological, esthetic, and corrosion properties. Zirconia orthopedic hip replacements have shown superior wear-resistance over other systems; however, risk of catastrophic fracture remains a concern. In dentistry, zirconia has been widely adopted for endosseous implants, implant abutments, and all-ceramic crowns. Because of an increasing demand for esthetically pleasing dental restorations, zirconia-based ceramic restorations have become one of the dominant restorative choices. Areas covered: This review provides an updated overview of the applications of zirconia in medicine and dentistry with a focus on dental applications. The MEDLINE electronic database (via PubMed) was searched, and relevant original and review articles from 2010 to 2016 were included. Expert commentary: Recent data suggest that zirconia performs favorably in both orthopedic and dental applications, but quality long-term clinical data remain scarce. Concerns about the effects of wear, crystalline degradation, crack propagation, and catastrophic fracture are still debated. The future of zirconia in biomedical applications will depend on the generation of these data to resolve concerns.