1
|
Kamonkhantikul K, Arksornnukit M, Homsiang W. Effect of thermocycling on the retentive force of the retentive inserts in three denture attachments and their water absorption ability. Dent Mater J 2024; 43:90-96. [PMID: 38148022 DOI: 10.4012/dmj.2023-175] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 12/28/2023]
Abstract
This study aimed to evaluate the thermocycling effect on the retentive force of 3 different retentive inserts in 3 denture attachments (Blue, Pink, Clear retentive inserts in LOCATOR; Blue, Pink, Clear retentive inserts in LOCATOR R-Tx; and White, Yellow, Green retentive inserts in Novaloc) (n=10). Maximum retentive force of each retentive insert was evaluated at baseline, 7-day water storage, and after 5,000-, and 10,000- cycle thermocycling. The water absorption percentage of the retentive inserts was also determined. Comparing between baseline and 7-day water storage, the retentive forces of the LOCATOR and LOCATOR R-Tx groups were significantly reduced (p<0.05), while the retentive force of the Novaloc group was significantly increased (p<0.05). Comparing between 7-day water storage and 10,000-cycle thermocycling, the retentive force of most retentive inserts remained unchanged (p>0.05). The water absorption percentage of the LOCATOR and LOCATOR R-Tx groups was significantly greater than that of the Novaloc group (p<0.05).
Collapse
Affiliation(s)
- Krid Kamonkhantikul
- Department of Prosthodontics, Faculty of Dentistry, Chulalongkorn University
| | | | - Woraporn Homsiang
- Department of Family and Community Dentistry, Faculty of Dentistry, Chiang Mai University
| |
Collapse
|
2
|
Ren J, Li C, Zhang S, Luo B, Tian M, Liu S, Wang L. Mass-producible in-situ amorphous solid/electrolyte interface with high ionic conductivity for long-cycling aqueous Zn-ion batteries. J Colloid Interface Sci 2023; 641:229-238. [PMID: 36933469 DOI: 10.1016/j.jcis.2023.03.080] [Citation(s) in RCA: 1] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 12/08/2022] [Revised: 02/22/2023] [Accepted: 03/11/2023] [Indexed: 03/14/2023]
Abstract
Although aqueous Zn-ion batteries (aZIBs) have garnered significant attention, they are yet to be commercialized due to severe corrosion and dendrite growth on Zn anodes. In this work, an artificial solid-electrolyte interface (SEI) with amorphous structure was created in-situ on the anode by immersing Zn foil in ethylene diamine tetra(methylene phosphonic acid) sodium (EDTMPNA5) liquid. This facile and effective method provides the possibility for Zn anode protection in large-scale applications. Experimental results, combined with theoretical calculations, indicate that the artificial SEI remains intact and adheres tightly to the Zn substrate. The negatively-charged phosphonic acid groups and disordered inner structure offer adequate sites for rapid Zn2+ transference and facilitate [Zn(H2O)6]2+ desolvation during charging/discharging. Due to the synergistic effect of the aforementioned advantages, the artificial SEI endows high Coulombic efficiency (CE, 99.75%) and smooth Zn deposition/stripping under the SEI. The symmetric cell exhibits a long cycling life of over 2400 h with low-voltage hysteresis. Additionally, full cells with MVO cathodes demonstrate the superiority of the modified anodes. This work provides insight into the design of in-situ artificial SEI on the Zn anode and self-discharge suppression to expedite the practical application of aZIBs.
Collapse
Affiliation(s)
- Junfeng Ren
- State Key Laboratory Base of Eco-Chemical Engineering, International Science and Technology Cooperation Base of Eco-chemical Engineering and Green Manufacturing, Qingdao University of Science and Technology, Qingdao 266042, China; College of Chemical Engineering, Qingdao University of Science and Technology, Qingdao 266042, China
| | - Caixia Li
- State Key Laboratory Base of Eco-Chemical Engineering, International Science and Technology Cooperation Base of Eco-chemical Engineering and Green Manufacturing, Qingdao University of Science and Technology, Qingdao 266042, China; Shandong Engineering Research Center for Marine Environment Corrosion and Safety Protection, College of Environment and Safety Engineering, Qingdao University of Science and Technology, Qingdao 266042, China.
| | - Shenghao Zhang
- State Key Laboratory Base of Eco-Chemical Engineering, International Science and Technology Cooperation Base of Eco-chemical Engineering and Green Manufacturing, Qingdao University of Science and Technology, Qingdao 266042, China; Shandong Engineering Research Center for Marine Environment Corrosion and Safety Protection, College of Environment and Safety Engineering, Qingdao University of Science and Technology, Qingdao 266042, China
| | - Bin Luo
- Nanomaterials Centre, School of Chemical Engineering and Australian Institute for Bioengineering and Nanotechnology, The University of Queensland, St Lucia, QLD 4072, Australia
| | - Minge Tian
- Scientific Green(shandong) Environmental Technology Co.Ltd, Jining Economic Development Zone, Shandong Province 272499, China
| | - Shiwei Liu
- College of Chemical Engineering, Qingdao University of Science and Technology, Qingdao 266042, China.
| | - Lei Wang
- State Key Laboratory Base of Eco-Chemical Engineering, International Science and Technology Cooperation Base of Eco-chemical Engineering and Green Manufacturing, Qingdao University of Science and Technology, Qingdao 266042, China; Shandong Engineering Research Center for Marine Environment Corrosion and Safety Protection, College of Environment and Safety Engineering, Qingdao University of Science and Technology, Qingdao 266042, China; College of Chemistry and Molecular Engineering, Qingdao University of Science and Technology, Qingdao 266042, China.
| |
Collapse
|