Stress behavior of an anterior single implant restored with high-performance polymer abutments under immediate and delayed loading: A 3D FEA study

Three-dimensional finite element analysis of the biomechanical behaviour of different dental implants under immediate loading during three masticatory cycles

The study aimed to evaluate the impact of varying modulus of elasticity (MOE) values of dental implants on the deformation and von Mises stress distribution in implant systems and peri-implant bone tissues under dynamic cyclic loading. The implant-bone interface was characterised as frictional contact, and the initial stress was induced using the interference fit method to effectively develop a finite element model for an immediately loaded implant-supported denture. Using the Ansys Workbench 2021 R2 software, an analysis was conducted to examine the deformation and von Mises stress experienced by the implant-supported dentures, peri-implant bone tissue, and implants under dynamic loading across three simulated masticatory cycles. These findings were subsequently evaluated through a comparative analysis. The suprastructures showed varying degrees of maximum deformation across zirconia (Zr), titanium (Ti), low-MOE-Ti, and polyetheretherketone (PEEK) implant systems, registering values of 103.1 μm, 125.68 μm, 169.52 μm, and 844.06 μm, respectively. The Zr implant system demonstrated the lowest values for both maximum deformation and von Mises stress (14.96 μm, 86.71 MPa) in cortical bone. As the MOE increased, the maximum deformation in cancellous bone decreased. The PEEK implant system exhibited the highest maximum von Mises stress (59.12 MPa), whereas the Ti implant system exhibited the lowest stress (22.48 MPa). Elevating the MOE resulted in reductions in both maximum deformation and maximum von Mises stress experienced by the implant. Based on this research, adjusting the MOE of the implant emerged as a viable approach to effectively modify the biomechanical characteristics of the implant system. The Zr implant system demonstrated the least maximum von Mises stress and deformation, presenting a more favourable quality for preserving the stability of the implant-bone interface under immediate loading.

Identifying an optimal approach for the placement of pterygoid implants: A 3D finite element analysis

STATEMENT OF PROBLEM

A consensus on the optimal approach to the placement of pterygoid implants is lacking.

PURPOSE

The purpose of this finite element analysis study was to determine the optimal approach to the placement of pterygoid implants by comparing biomechanical behavior.

MATERIAL AND METHODS

An edentulous and moderately atrophic maxilla with the anatomic structure of the pterygomaxillary region was constructed. Complete arch restorations with 4 standard anterior implants and pterygoid implants in 3 approaches were simulated: L70, long pterygoid implants (4.1×18 mm) inclined at 70 degrees relative to the Frankfort horizontal plane with anchorage in the pterygoid process; L45, long pterygoid implants (4.1×20 mm) inclined at 45 degrees with anchorage in the pterygoid process; and S45, shorter pterygoid implants (4.1×13 mm) inclined 45 degrees without apical anchorage. The L70, L45, and S45 groups were classified as D or S depending on the bone quality: D3 (dense trabecular bone) or D4 (sparse trabecular bone). A total of 6 finite element models were built. The bone failure theory, based on the von Mises theory, was used to judge yielding of the trabecular bone. The von Mises stress (σVM) distribution was measured in the cortical bone, the trabecular bone, and on the implant surface. Deformation (DF) distribution was obtained for the entire bone (DFB) and bone surrounding the pterygoid implant (DFP).

RESULTS

L70 showed a lower maximum σVM value (maxσVM), more uniform σVM distribution in the cortical bone, trabecular bone, and on the implant surface and a lower maximum DFp value (maxDFp), especially in the D4 bone. The biomechanical behaviors were similar in L45 and S45 with no stress distribution in the pterygoid process. In the D4 bone, L70, L45, and S45 exceeded the limited stress of the bone failure theory by 50%, 130%, and 130%, while all values were under the limit in D3 bone.

CONCLUSIONS

The approach of pterygoid implants inclined at 70 degrees relative to the Frankfort plane with anchorage in the pterygoid process was optimal, providing improved biomechanical behavior. Clinically, in the case of D4 bone, the inclined angulation of pterygoid implants should be 70 degrees to minimize the risk of failure.

A Modified Ridge-Splitting Technique to Restore a Completely Edentulous Maxillary Arch With a Cement-Retained Implant Prosthesis

The present report describes a technique in which the maxillary bone was molded to the desired location using a series of instruments for ridge-splitting procedures. This technique aims to improve bone quality all around the implants at both the crest and apex locations. In some clinical scenarios, insufficient horizontal bone with less than 3 mm prevents implant placement. Thus, ridge splitting is a treatment of choice, and this technique creates bone expansion to form a better receptor site for endosteal implants. A case report is presented involving a completely edentulous 52-year-old male patient presented to the clinic with a horizontal bone defect. The patient complained of having difficulty eating and wants to improve his smile. In this clinical case, a modified ridge-splitting technique was employed, differing from the conventional procedure that uses mallets, chisels, or osteotomes. A lancet and spatula were used for precise ridge splitting, followed by the placement of four endosseous tapered implants-two on each side (Dentis USA, La Palma, USA). Each implant had a diameter of 3.7 mm and a length of 10 mm. These implants were clinically placed in a single visit, with a torque of 30 N/cm² applied to ensure secure fixation. To accommodate the patient's unique maxillary bone anatomy, 25-degree angulated abutments were chosen for the four implants, ensuring a common path of insertion, and optimal angulation for long-term stability and aesthetics. Subsequently, a cemented provisional dental prosthesis restoration was fitted, and the patient reported satisfaction with both function and aesthetics. After a period of five months of osseointegration, the stability of the implants was assessed using a resonance frequency analyzer, yielding positive results. The average resonance frequency values for the maxillary left (canine and premolar) were ISQ 68 and ISQ 71, respectively, while for the maxillary right (lateral incisor and premolar), the values were ISQ 69 and ISQ 73. These readings indicate satisfactory implant stability following the osseointegration process. The postoperative cone-beam computed tomography (CBCT) showed gain to the bone width besides better function and good results concerning the esthetics. This report describes a modified ridge-splitting technique with a predictable and satisfactory outcome that fulfilled the patient's demands. The presented approach overcomes the disadvantages of two-staged implant placement bone grafting procedures and is also a more affordable option for the patient. CBCT evaluation confirmed bone gain with minimal morbidity after the procedure.