Titanium Alloy Gamma Nail versus Biodegradable Magnesium Alloy Bionic Gamma Nail for Treating Intertrochanteric Fractures: A Finite Element Analysis

SrHPO4-coated Mg alloy implant attenuates postoperative pain by suppressing osteoclast-induced sensory innervation in osteoporotic fractures

Osteoporotic fractures have become a common public health problem and are usually accompanied by chronic pain. Mg and Mg-based alloys are considered the next-generation orthopedic implants for their excellent osteogenic inductivity, biocompatibility, and biodegradability. However, Mg-based alloy can initiate aberrant activation of osteoclasts and modulate sensory innervation into bone callus resulting in postoperative pain at the sequential stage of osteoporotic fracture healing. Its mechanism is going to be investigated. Strontium hydrogen phosphate (SrHPO4) coating to delay the Mg-based alloy degradation, can reduce the osteoclast formation and inhibit the growth of sensory nerves into bone callus, dorsal root ganglion hyperexcitability, and pain hypersensitivity at the early stage. Liquid chromatography-mass spectrometry (LC-MS) metabolomics analysis of bone marrow-derived macrophages (BMMs) treated with SrHPO4-coated Mg alloy extracts shows the potential effect of increased metabolite levels of AICAR (an activator of the AMPK pathway). We demonstrate a possible modulated secretion of AICAR and osteoclast differentiation from BMMs, which inhibits sensory innervation and postoperative pain through the AMPK/mTORc1/S6K pathway. Importantly, supplementing with AICAR in Mg-activated osteoclasts attenuates postoperative pain. These results suggest that Mg-induced postoperative pain is related to the osteoclastogenesis and sensory innervation at the early stage in the osteoporotic fractures and the SrHPO4 coating on Mg-based alloys can reduce the pain by upregulating AICAR secretion from BMMs or preosteoclasts.

Biomechanical optimization of the magnesium alloy bionic cannulated screw for stabilizing femoral neck fractures: a finite element analysis

Purposes

The magnesium alloy bionic cannulated screw (MABCS) was designed in a previous study promoting cortical-cancellous biphasic healing of femoral neck fractures. The main purpose was to analyze the bore diameters that satisfy the torsion standards and further analyze the optimal pore and implantation direction for stabilizing femoral neck fractures.

Methods

The MABCS design with bionic holes with a screw diameter of less than 20% met the torsion standard for metal screws. The MABCS was utilized to repair the femoral neck fracture via Abaqus 6.14 software, which simulated the various stages of fracture healing to identify the optimal biomechanical environment for bionic hole size (5%, 10%, 15%, and 20%) and implantation direction (0°, 45°, 90°, and 135°).

Results

The stress distribution of the MABCS fracture fixation model is significantly improved with an implantation orientation of 90°. The MABCS with a bionic hole and a screw diameter of 10% provides optimal stress distribution compared with the bionic cannulated screw with diameters of 5%, 15%, and 20%. In addition, the cannulated screw fixation model with a 10% bionic hole size has optimal bone stress distribution and better internal fixation than the MABCS fixation models with 5%, 15%, and 20% screw diameters.

Conclusion

In summary, the MABCS with 10% screw diameter bionic holes has favorable biomechanical characteristics for stabilizing femoral neck fractures. This study provides a biomechanical foundation for further optimization of the bionic cannulated screw.

Biomechanical evaluation of ortho-bridge system and proximal femoral nail antirotation in intertrochanteric fractures with lateral wall fracture based on finite element analysis

Background

The integrity of the lateral wall in femoral intertrochanteric fractures significantly impacts fracture stability and internal fixation. In this study, we compared the outcomes of treating intertrochanteric fractures with lateral wall involvement using the ortho-bridge system (OBS) combined with proximal femoral nail antirotation (PFNA) versus simple PFNA from a biomechanical perspective.

Methods

Finite-element models of femoral intertrochanteric fractures with lateral wall involvement were subjected to fixation with OBS combined with PFNA and simple PFNA. Von Mises stress measurements and corresponding displacement assessments for each component of the model, including the proximal femur and lateral wall, were used to evaluate the biomechanical effects of OBS fixation on bone and intramedullary nail stability.

Results

Using PFNA alone to fix intertrochanteric fractures with lateral wall involvement resulted in von Mises stress levels on the lateral wall exceeding safe stress tolerances for bone growth. OBS fixation significantly reduced stress on the lateral wall of the femur and minimized the stress on each part of the intramedullary nail, reducing the overall displacement.

Conclusion

In cases of intertrochanteric fractures with lateral wall involvement, PFNA fixation alone may compromise the biomechanical integrity of the lateral femoral wall, increasing the risk of postoperative complications. The addition of OBS to PFNA significantly reduces stress on the lateral femoral wall. Consequently, OBS should be considered for lateral wall fixation when managing intertrochanteric fractures combined with lateral wall fractures.

A Controlled Variable Study of the Biomechanical Properties of the Proximal Femur before and after Cancellous Bone Removal

OBJECTIVE

The biomechanical characteristics of proximal femoral trabeculae are closely related to the occurrence and treatment of proximal femoral fractures. Therefore, it is of great significance to study its biomechanical effects of cancellous bone in the proximal femur. This study examines the biomechanical effects of the cancellous bone in the proximal femur using a controlled variable method, which provide a foundation for further research into the mechanical properties of the proximal femur.

METHODS

Seventeen proximal femoral specimens were selected to scan by quantitative computed tomography (QCT), and the gray values of nine regions were measure to evaluated bone mineral density (BMD) using Mimics software. Then, an intact femur was fixed simulating unilateral standing position. Vertical compression experiments were then performed again after removing cancellous bone in the femoral head, femoral neck, and intertrochanteric region, and data were recorded. According to the controlled variable method, the femoral head, femoral neck, and intertrochanteric trabeculae were sequentially removed based on the axial loading of the intact femur, and the displacement and strain changes of the femur samples under axial loading were recorded. Gom software was used to measure and record displacement and strain maps of the femoral surface.

RESULTS

There was a statistically significant difference in anteroposterior displacement of cancellous bone destruction in the proximal femur (p < 0.001). Proximal femoral bone mass explained 77.5% of the strength variation, in addition proximal femoral strength was mainly affected by bone mass at the level of the upper outer, lower inner, lower greater trochanter, and lesser trochanter of the femoral head. The normal stress conduction of the proximal femur was destroyed after removing cancellous bone, the stress was concentrated in the femoral head and lateral femoral neck, and the femoral head showed a tendency to subside after destroying cancellous bone.

CONCLUSION

The trabecular removal significantly altered the strain distribution and biomechanical strength of the proximal femur, demonstrating an important role in supporting and transforming bending moment under the vertical load. In addition, the strength of the proximal femur mainly depends on the bone density of the femoral head and intertrochanteric region.

Proximal femoral bionic nail-a novel internal fixation system for the treatment of femoral neck fractures: a finite element analysis

Introduction: Currently, cannulated screws (CSs) and dynamic hip screws (DHSs) are widely used for the treatment of femoral neck fractures, but the postoperative complications associated with these internal fixations remain high. In response to this challenge, our team proposes a new approach involving triangular-supported fixation and the development of the proximal femoral bionic nail (PFBN). The primary objective of this study is to investigate the biomechanical differences among CSs, DHSs, and the PFBN in their capacity to stabilize femoral neck fractures. Methods: A normal proximal femur model was constructed according to the CT data of a normal healthy adult. A femoral neck fracture model was constructed and fixed with CSs, DHSs, and the PFBN to simulate the fracture fixation model. Abaqus 6.14 software was used to compare the biomechanical characters of the three fracture fixation models. Results: The maximum stresses and displacements of the normal proximal femur were 45.35 MPa and 2.83 mm, respectively. Under axial loading, the PFBN was more effective than DHSs and CSs in improving the stress concentration of the internal fixation and reducing the peak values of von Mises stress, maximum principal stress, and minimum principal stress. The PFBN fixation model exhibits superior overall and fracture section stability in comparison to both the DHS fixation model and the CS fixation model under axial loading. Notably, the maximum stress and peak displacement of the PFBN and bone were lower than those of the DHS and CS fixation models under bending and torsional loading. Conclusion: The PFBN shows considerable improvement in reducing stress concentration, propagating stress, and enhancing the overall stability in the femoral neck fracture fixation model compared to DHSs and CSs. These enhancements more closely correspond to the tissue structure and biomechanical characteristics of the proximal femur, demonstrating that the PFBN has great potential for therapeutic purposes in treating femoral neck fractures.

Mechanical Gains Associated With Virtual Prophylactic Intramedullary Nail Fixation in Femurs With Metastatic Disease

Background

Many patients with metastatic bone disease (MBD) of the femur undergo prophylactic surgical fixation for impending pathologic fractures; intramedullary nailing (IMN) being the most common fixation type. However, surgeons often question if IMN fixation provides sufficient improvements in mechanical strength for particular metastatic lesions. Our goal was to use patient-specific finite element (FE) modeling to computationally evaluate the effects of simulated IMN fixation on the mechanics of femurs affected with MBD.

Methods

Computed tomography (CT) scans were available retrospectively from 48 patients (54 femurs) with proximal femoral metastases. The CT scans were used to create patient-specific, non-linear, voxel-based FE models of the femur, simulating the instant of peak hip joint contact force during normal walking. FE analyses were repeated after incorporating virtual IMN fixation (Smith and Nephew, TRIGEN INTERTAN) into the same femurs. Femur strength and load-to-strength ratio (LSR; lower LSR indicates lower fracture risk) were compared between untreated and IMN conditions using statistical analyses.

Results

IMN fixation resulted in a very modest average 10% increase in mechanical strength (p<0.001), which was associated with a slight 7% reduction in fracture risk (p<0.001). However, there was considerable variation in fracture risk reduction between individual femurs (0.13-50%). In femurs with the largest reduction in fracture risk (>10%), IMN hardware directly passed through a considerable section of that femur's metastatic lesion. Femurs with lytic (10%) and diffuse (9%) metastases tended to have greater reductions in fracture risk compared to femurs with blastic (5%) and mixed (4%) metastases (p=0.073).

Conclusion

Given the mechanically strong baseline condition of most femurs in this cohort, evident by the low fracture risk at the time of CT scanning, the relative increase in stiffness with the addition of the IMN hardware may not make a substantial contribution to overall mechanical strength. The mechanical gains of IMN fixation in femurs with MBD appear most beneficial when the hardware traverses an adequate section of the lesion. Level of Evidence: III.

Biomechanical properties and clinical significance of cancellous bone in proximal femur: A review

Trabecular bone plays an important role in the load-bearing capacity of the femur. Understanding the structural characteristics, biomechanics, and mechanical conduction of the trabecular bone is of great value in studying the mechanism of fractures and formulating surgical plans. The past decade has witnessed unprecedented progress in imaging, biomechanics and finite element analysis techniques, translating into a better understanding of trabecular bone. This article reviews the research progress achieved over the years regarding femoral trabecular bone, especially on factors influencing the strength of the proximal femoral cancellous bone and cancellous bone microfractures and provides a comprehensive overview of the latest findings on proximal femoral trabecular bone and their clinical significance.

Triangular support intramedullary nail: A new internal fixation innovation for treating intertrochanteric fracture and its finite element analysis

BACKGROUND

Proximal femoral nail anti-rotation (PFNA) and Gamma nail were recommended for intertrochanteric fracture, however, with high rate of post-operation complications. The triangular support intramedullary nail (TSIN) was designed to reduce the risk of postoperative complications related to Gamma nail and PFNA, and the aim is to compare the biomechanical characters of Gamma nail, PFNA and TSIN for fixation of intertrochanteric fracture and prove the rationality of the concept of triangle fixation in the treatment of intertrochanteric fractures.

METHODS

The finite element model of proximal femur was constructed according to the CT data of femur. Intertrochanteric fracture models with Evans type Ⅰ and Ⅳ were established and fixed with Gamma nail, PFNA and TSIN by UG-NX 12.0. The finite element analysis software was used to compare the stress distribution and displacement of three implants fixation models.

RESULTS

Under axial loading of 600 N, the peak stress and maximum displacement of intact proximal femur was 13.78 MPa and 1.33 mm, respectively. The maximum stress of TSIN for fixation of Evans type Ⅰ and Ⅳ intertrochanteric fractures was 86.23 MPa and 160.63 MPa which was significantly lower than that of Gamma nail and PFNA. The maximum relative displacement of fracture section in Gamma nail and PFNA fixation models was 0.18 mm and 0.19 mm which has 135% and 148% higher than in TSIN fixation models for fixing Evans type Ⅰ intertrochanteric fracture, and 0.47 mm and 0.59 mm which has 91% and 140% higher than in TSIN fixation models for stabilization of Evans type Ⅳ intertrochanteric fracture.

CONCLUSION

Compared with Gamma nail and PFNA fixation, TSIN has superior advantages in stress distribution and construct stability. We believe that triangle fixation concept help to reduce the risk of post-operative complications associated with PFNA and Gamma nail and improve the clinical effect of intertrochanteric fracture.

A comparative Study of Novel Extramedullary Fixation and Dynamic Hip Screw in the Fixation of Intertrochanteric Fracture: A Finite-Element Analysis

Background

Dynamic hip screw (DHS) is one of the most widely internal fixations for stabilizing intertrochanteric fracture, however, with a high risk of postoperative complications. The triangle support fixation plate (TSFP) is developed to reduce the postoperative complications. The purpose of study is to evaluate the biomechanical performance of the DHS and TSFP and demonstrate the rationality of triangular internal fixation for stabilizing intertrochanteric fractures.

Methods

The CT data of the proximal femur were used to establish finite-element models. Evans type I and IV intertrochanteric fracture were constructed and stabilized with the DHS and TSFP. The Von-Mises stress, maximum principal stress, minimum principal stress, and displacement were used to evaluate the biomechanical effect of two implants on intertrochanteric fracture.

Results

Under a 600N axial load, the maximum stress and displacement of an intact proximal femur were 13.78 MPa and 1.33 mm, respectively. The peak stresses of the bone in the TSFP were 35.41 MPa and 68.97 MPa for treating Evans type I and IV intertrochanteric fractures, respectively, which were lower than those in the DHS. The maximum overall displacement and relative distance of the fracture surface in the DHS fixation model were 1.66 mm and 0.10 mm for treating Evans type I intertrochanteric fracture, which was 29.59% and 150% higher than that in the TSFP, and were 2.24 mm and 0.75 mm for treating Evans type IV intertrochanteric fracture, which was 42.58% and 650% higher than that in the TSFP.

Conclusions

In conclusion, the TSFP has obvious advantages in stress distribution and stability than the DHS, providing a promising option for the treatment of intertrochanteric fractures.

Feasibility analysis of an ultrasound on line diagnostic approach for oral and bone surgery

During implant surgery procedures, surgical precision is an essential prerequisite for the functional and aesthetic success of the prosthetic crown to be placed on the dental implant. A modern implant surgical approach should be standardized as much as possible to guarantee extreme precision in the insertion of the implant into the upper and lower bone jaws. Among the most common surgical errors during implant surgery there is the over-preparation of the surgical alveolus with possible damage to the contiguous anatomical structures. To avoid this problem, in the recent years, there has been an increasing attention to the development of new control techniques. In this paper, we describe an innovative ultrasound approach, which exploits the integration of an electro-acoustic transducer with the surgical drill used for realizing the alveolus in the bone that will host the implant. Specifically, he proposed approach is based on the "time-of-flight" detection technique for measuring the thickness of the residual bone subjected to the drilling. In order to demonstrate the feasibility of the proposed approach, here we report on a detailed numerical analysis aimed at studying the propagation of ultrasonic waves through the drill-bit and through the involved tissues. The obtained results confirm the validity of our approach, and enable for a future first prototype implementation of a hi-tech surgical drill-bit, which in general is suitable not only for dental implant surgery but also for other uses in oral surgery, maxillofacial surgery and for bone surgery.

Biomechanical study on the stability and strain conduction of intertrochanteric fracture fixed with proximal femoral nail antirotation versus triangular supporting intramedullary nail

OBJECTIVES

Based on the features of the three-dimensional spatial structure of the proximal femoral trabeculae, we developed a bionic triangular supporting intramedullary nail (TSIN) for the treatment of the femoral intertrochanteric fracture. The current study aimed to compare the mechanical stability and restoration of mechanical conduction between proximal femoral nail antirotation (PFNA) and TSIN to fix the intertrochanteric fractures.

METHODS

Firstly, five sets of PFNA and TSIN with the same size were selected and fixed on a biomechanical testing machine, and strain gauges were pasted on the main nail, lag screw, and supporting screw to load to the vertical load to 600 N, and the displacement and strain values were recorded. Secondly, formalin-preserved femurs were selected, and the left and right femurs of the same cadaver were randomly divided into two groups to prepare intertrochanteric femur fractures (AO classification 31-A1), which were fixed with PFNA (n = 15) and TSIN (n = 15), respectively. Sixteen sites around the fracture line were chosen to paste strain gauges and loaded vertically to 600 N, and then, the fracture fragment displacement and strain values were recorded. Finally, a 10,000-cycle test ranging from 10 to 600 N was conducted, and the cycle number and displacement value were recorded.

RESULTS

The overall displacement of PFNA was 2.17 ± 0.18 mm, which was significantly greater than the displacement of the TSIN group (1.66 ± 0.05 mm, P < 0.05) under a vertical load of 600 N. The strain below the PFNA lag screw was 868.29 ± 147.85, which was significantly greater than that of the TSIN (456.02 ± 35.06, P < 0.05); the strain value at the medial side of the PFNA nail was 444.00 ± 34.23, which was significantly less than that of the TSIN (613.57 ± 108.00, P < 0.05). Under the vertical load of 600 N, the displacement of the fracture fragments of the PFNA group was 0.95 ± 0.25 mm, which was significantly greater than that of the TSIN group (0.41 ± 0.09 mm, P < 0.05). The femoral specimens in the PFNA group showed significantly greater strains at the anterior (1, 2, and 4), lateral (7, 9, and 10), posterior (11), and medial (15 and 16) sites than those in the TSIN group (all P < 0.05). In the cyclic compression experiment, the displacements of the PFNA group at 2000, 4000, 6000, 8000, and 10,000 cycles were 1.38 mm, 1.81 mm, 2.07 mm, 2.64 mm, and 3.58 mm, respectively, which were greater than the corresponding displacements of the TSIN group: 1.01 mm, 1.48 mm, 1.82 mm, 2.05 mm, and 2.66 mm (P₈₀₀₀ = 0.012, P₁₀₀₀₀ = 0.006).

CONCLUSIONS

The current study showed that TSIN had apparent advantages in stability and stress conduction. TSIN enhanced the stability of intertrochanteric fractures, particularly in superior fracture fragments, improved stress conduction, reduced the stress in the anterior and medial femur, and restored the biomechanical properties of the femur.