Foodborne disease outbreaks in flour and flour-based food products from microbial pathogens in the United States, and their health economic burden

Factors Affecting the Adhesion of Flour Particles to Stainless-steel Surfaces and Vacuum Dry-cleaning

Recent outbreaks and recalls linked to flour-based products have highlighted the need for improved cleaning methods in low-moisture environments. The factors affecting adhesion forces of flour particles, and the vacuum cleaning methodologies to overcome these forces, need to be better understood. The objectives of this study were to: (1) Measure electrostatic charge build-up in flour under different environmental conditions (20, 40, 60% relative humidity at room temperature), (2) quantify how powder size (US standard No. 60-80 or 80-100 mesh), electrostatic charge (charged and uncharged), and relative humidity impact the force required to remove the powder from an electropolished 304 stainless steel coupon (8 × 8 × 0.2 cm), and (3) determine the most effective vacuum nozzle angle (0, 45, 90° relative to the surface) for cleaning. Chargeability (nC) of flour samples was assessed using Faraday cup electrometry, while the surface adhesion force of the flour particles was measured using a custom-built impact tester. The surface cleanliness after vacuum treatments was assessed using ATP (adenosine triphosphate) swabs and a luminometer. Charged flour samples at 20% relative humidity (RH) exhibited a significantly higher charge compared to those at 40 and 60% RH. Within the 60-80 mesh range, charged flour showed higher adhesion rates than uncharged samples at both 20 and 40% RH. However, in the 80-100 mesh range, charged flour did not show a significant difference in adhesion when compared to uncharged samples at any RH level. Additionally, at 60% RH, surface residues measured by ATP were significantly lower for a vacuum angle of 90° than for 0° across both 60-80 mesh and 80-100 mesh size ranges of wheat flour. The vacuum cleaning treatment proved capable of overcoming the increase in adhesion from triboelectric forces; however, trace flour residues were still detected on stainless steel surfaces postvacuuming, indicating that vacuuming alone may be insufficient.

Outbreak of Listeriosis Likely Associated with Baker's Yeast Products, Switzerland, 2022-2024

We traced back a nationwide outbreak of human listeriosis in Switzerland to a persisting production line contamination of a factory producing baker's yeast with Listeria monocytogenes serotype 1/2a sequence type 3141. We used whole-genome sequencing to match clinical isolates to isolates from product samples.

Food Safety Research and Extension Needs for the U.S. Low-Moisture Food Industry

Historically, low-moisture foods were considered to have minimal microbial risks. However, they have been linked to many high-profile multistate outbreaks and recalls in recent years, drawing research and extension attention to low-moisture food safety. Limited studies have assessed the food safety research and extension needs for the low-moisture food industry. The objectives of this needs assessment were to explore the food safety culture and education needs, identify the food safety challenges and data gaps, and understand the barriers to adopting food-safety-enhancing technologies in the U.S. low-moisture food industry. This needs assessment was composed of two studies. In Study 1, food safety experts from the low-moisture food industry upper management participated in online interviews and a debriefing discussion session. In Study 2, an online anonymous survey was disseminated to a different group of experts with experience in the low-moisture food industry. The qualitative data were analyzed using deductive and inductive coding approaches, while the quantitative data were analyzed via descriptive analysis. Twenty-five experts participated in the studies (Study 1: n = 12; Study 2: n = 13). Common commodities that participants had worked with included nuts and seeds, spices, flour, and dried fruits and vegetables. A food safety culture conceptual framework was adapted, which included three main components: infrastructure conditions (foundation), individual's food safety knowledge, attitudes, and risk perceptions; and organizational conditions (supporting pillars). Major barriers to establishing a positive food safety culture were identified to be limited resources, difficulties in risk communication, and difficulties in behavioral change. For continual improvement in food safety performance, two major themes of food safety challenges and data gaps were identified: cleaning, sanitation, and hygienic design; and pathogen reduction. Participants perceived the main barriers discouraging the low-moisture food industry from adopting food-safety-enhancing technologies were: (1) budgetary priorities, (2) operation constraints, (3) technology validation, (4) consumer acceptance, and (5) maintaining desired product characteristics such as quality and sensory functionality. The findings of this needs assessment provide guidance for the food industry, academia, and government agencies about the direction of future research and the development of targeted extension programs that might help improve food safety in the low-moisture food industry.

High-throughput fabrication of antimicrobial phage microgels and example applications in food decontamination

Engineered by nature, biological entities are exceptional building blocks for biomaterials. These entities can impart enhanced functionalities on the final material that are otherwise unattainable. However, preserving the bioactive functionalities of these building blocks during the material fabrication process remains a challenge. We describe a high-throughput protocol for the bottom-up self-assembly of highly concentrated phages into microgels while preserving and amplifying their inherent antimicrobial activity and biofunctionality. Each microgel is comprised of half a million cross-linked phages as the sole structural component, self-organized in aligned bundles. We discuss common pitfalls in the preparation procedure and describe optimization processes to ensure the preservation of the biofunctionality of the phage building blocks. This protocol enables the production of an antimicrobial spray containing the manufactured phage microgels, loaded with potent virulent phages that effectively reduced high loads of multidrug-resistant Escherichia coli O157:H7 on red meat and fresh produce. Compared with other microgel preparation methods, our protocol is particularly well suited to biological materials because it is free of organic solvents and heat. Bench-scale preparation of base materials, namely microporous films (the template for casting microgels) and pure concentrated phage suspension, requires 3.5 h and 5 d, respectively. A single production run, that yields over 1,750,000 microgels, ranges from 2 h to 2 d depending on the rate of cross-linking chemistry. We expect that this platform will address bottlenecks associated with shelf-stability, preservation and delivery of phage for antimicrobial applications, expanding the use of phage for prevention and control of bacterial infections and contaminants.