Measuring the global mechanical properties of the human thorax: Costo-vertebral articulation

Biomechanical simulation of the human thorax, e.g. for 3D-printed rib implant optimisation, requires an accurate knowledge of the associated articulation and tissue stiffness. The present study is focusing on determining the stiffness of the costo-vertebral articulations. Specimens of rib segments including the adjacent thoracic vertebrae and ligaments were obtained from two human post-mortem bodies at four different rib levels. The rib samples were loaded with a tensile force in the local longitudinal, sagittal and transverse direction and the resulting displacement was continuously measured. The moment-angle response of the rib articulations was also determined by applying a load at the rib end in the cranial - caudal direction and measuring the resulting displacement. The torsional load response of the costo-vertebral articulations at an applied moment between -0.1 Nm and 0.1 Nm corresponded to a median range of motion of 13.2° (6.4° to 20.9°). An almost uniform stiffness was measured in all tensile loading directions. The median displacement at the defined force of 28 N was 1.41 mm in the longitudinal, 1.55 mm in the sagittal, and 1.08 mm in the transverse direction. The measured moment-angle response of the costo-vertebral articulation is in line with the data from literature. On the contrary, larger displacements in longitudinal, sagittal and transverse directions were measured compared to the values found in literature.

The heterogeneous mechanical properties of adolescent growth plate cartilage: A study in rabbit

The growth plate is a cartilaginous tissue that functions to lengthen bones in children. When fractured, however, the growth plate can lose this critical function. Our understanding of growth plate fracture and mechanobiology is currently hindered by sparse information on the growth plate's microscale spatial gradients in mechanical properties. In this study, we performed microindentation across the proximal tibia growth plate of 9-week-old New Zealand White rabbits (n = 15) to characterize spatial variations in mechanical properties using linear elastic and nonlinear poroelastic material models. Mean indentation results for Hertz reduced modulus ranged from 380 to 690 kPa, with a peak in the upper hypertrophic zone and significant differences (p < 0.05) between neighboring zones. Using a subset of these animals (n = 7), we characterized zonal structure and extracellular matrix content of the growth plate through confocal fluorescent microscopy and Raman spectroscopy mapping. Comparison between mechanical properties and matrix content across the growth plate showed that proteoglycan content correlated with compressive modulus. This study is the first to measure poroelastic mechanical properties from microindentation across growth plate cartilage and to discern differing mechanical properties between the upper and lower hypertrophic zones. This latter finding may explain the location of typical growth plate fractures. The spatial variation in our reported mechanical properties emphasize the heterogeneous structure of the growth plate which is important to inform future regenerative implant design and mechanobiological models.

In vitro biomechanical properties of sole tissues: Comparison between healthy and ulcerated bovine claws

Sole ulcers are reportedly one of the most prevalent diseases associated with lameness in dairy cattle, significantly affecting animal welfare and farm profitability. The degree to which sole soft tissues, healthy or ulcerated, are able to maintain their structure and function when subjected to compressive forces remains unknown. Therefore, the aims of the present study were to assess sole tissue biomechanics in healthy and ulcerated claws and to describe correlated histology. Cylindrical samples were harvested from zones 4 and 6, as described by the international foot map, from hind lateral healthy (n = 12) and ulcerated bovine claws (n = 8; animals n = 12). Tissue biomechanics and morphology were evaluated via compressive tests and hematoxylin-eosin-phloxine-saffron staining, respectively. A 2-sample t-test was used to compare zones' mechanical properties between healthy and ulcerated tissues, and the Cochran-Mantel-Haenszel test was used to measure the effect of claw zone on histology. The fibril modulus (E_f) and permeability (k) respectively increased and decreased in ulcerated claws (E_f = 0.201 ± 0.104 MPa; k = 0.128 ± 0.069 mm²/MPa·s) compared with healthy claws (E_f = 0.105 ± 0.050 MPa; k = 0.452 ± 0.365 mm²/MPa·s) only for zone 6. Histology scores equal to or greater than 3 were associated with macroscopic presence of ulceration. A higher proportion of adipose tissue (30% or more) was associated with zone 6 compared with zone 4, but no difference was seen between healthy and ulcerated claws. Ulcerated claws had a higher prevalence of exostoses compared with healthy ones (33% vs. 8%). Sole soft tissues showed, as hypothesized, a viscoelastic behavior using unconfined compression testing, which, however, may not reflect in vivo loading conditions. Clinical and histological signs of sole ulceration were not associated with decreased strength of the supportive apparatus of the distal phalanx in zone 4 in this study.

Biomechanical and morphological stability of acellular scaffolds for tissue-engineered heart valves depends on different storage conditions

Currently available bioprosthetic heart valves have been successfully used clinically; however, they have several limitations. Alternatively, tissue-engineering techniques can be used. However, there are limited data concerning the impact of storage conditions of scaffolds on their biomechanics and morphology. The aim of this study was to determine the effect of different storage conditions on the biomechanics and morphology of pulmonary valve dedicated for the acellular scaffold preparation to achieve optimal conditions to obtain stable heart valve prostheses. Scaffold can then be used for the construction of tissue-engineered heart valve, for this reason evaluation of these parameters can determine the success of the clinical application this type of bioprosthesis. Pulmonary heart valves were collected from adult porcines. Materials were divided into five groups depending on the storage conditions. Biomechanical tests were performed, both the static tensile test, and examination of viscoelastic properties. Extracellular matrix morphology was evaluated using transmission electron microscopy and immunohistochemistry. Tissue stored at 4 °C exhibited a higher modulus of elasticity than the control (native) and fresh acellular, which indicated the stiffening of the tissue and changes of the viscoelastic properties. Such changes were not observed in the radial direction. Percent strain was not significantly different in the study groups. The storage conditions affected the acellularization efficiency and tissue morphology. To the best of our knowledge, this study is the first that attributes the mechanical properties of pulmonary valve tissue to the biomechanical changes in the collagen network due to different storage conditions. Storage conditions of scaffolds for tissue-engineered heart valves may have a significant impact on the haemodynamic and clinical effects of the used bioprostheses.