Interpretation of Experimental Data is Substantial for Constitutive Characterization of Arterial Tissue

The paper aims at evaluation of mechanical tests of soft tissues and creation of their representative stress-strain responses and respective constitutive models. Interpretation of sets of experimental results depends highly on the approach to the data analysis. Their common representation through mean and standard deviation may be misleading and give nonrealistic results. In the paper, raw data of seven studies consisting of 11 experimental data sets (concerning carotid wall and atheroma tissues) are re-analyzed to show the importance of their rigorous analysis. The sets of individual uniaxial stress-stretch curves are evaluated using three different protocols: stress-based, stretch-based, and constant-based, and the population-representative response is created by their mean or median values. Except for nearly linear responses, there are substantial differences between the resulting curves, being mostly the highest for constant-based evaluation. But also the stretch-based evaluation may change the character of the response significantly. Finally, medians of the stress-based responses are recommended as the most rigorous approach for arterial and other soft tissues with significant strain stiffening.

Angioplasty Induced Changes in Dialysis Vascular Access Compliance

Dialysis vascular access remains vitally important to maintain life and functional capacity with end stage renal disease. Angioplasty is an integral part of maintaining dialysis access function and patency. To understand the effect of angioplasty balloon dilation on vascular wall mechanics, we conducted a clinical study to evaluate the elastic modulus of the anastomosis in five subjects with anastomosis stenoses, before and after six angioplasty procedures, using B-mode ultrasound DICOM data. A novel and open source vascular ultrasound high-resolution speckle tracking software tool was used. The median lumen diameter increased from 3.4 to 5.5 mm after angioplasty. Meanwhile, the median elastic modulus of the 18 measurements at the anastomosis increased by 52.2%, from 2.24 × 10³ to 3.41 × 10³ mmHg. The results support our hypothesis that the structural changes induced in the vessel wall by balloon dilation lead to reduced vascular compliance and a higher elastic modulus of the vessel wall.

Relating the mechanical properties of atherosclerotic calcification to radiographic density: A nanoindentation approach

Calcification morphology can determine atherosclerotic plaque stability and is associated with increased failures rates for endovascular interventions. Computational efforts have sought to elucidate the relationship between calcification and plaque rupture in addition to predicting tissue response during aggressive revascularisation techniques. However, calcified material properties are currently estimated and may not reflect real tissue conditions. The objective of this study is to correlate calcification mechanical properties with three radiographic density groups obtained from corresponding Computed Tomography (CT) images. Seventeen human plaques extracted from carotid (n = 10) and peripheral lower limb (n = 7) arteries were examined using micro-computed tomography (µCT), simultaneously locating the calcified deposits within their internal structure and quantifying their densities. Three radiographic density groups were defined based on the sample density distribution: (A) 130-299.99 Hounsfield Units (HU), (B) 300-449.99 HU and (C) >450 HU. Nanoindentation was employed to determine the Elastic Modulus (E) and Hardness (H) values within the three density groups. Results reveal a clear distinction between mechanical properties with respect to radiographic density groups (p < 0.0005). No significant differences exist in the density-specific behaviours observed between carotid and peripheral samples. Previously defined calcification classifications indicate an association with specific radiographic density patterns. Scanning Electron Microscopy (SEM) examination revealed that density group A regions consist of both calcified and non-calcified tissues. Further research is required to define the radiographic thresholds which identify varying degrees of tissue calcification. This study demonstrates that the mechanical properties of fully mineralised atherosclerotic calcification emulate that of bone tissues (17-25 GPa), affording computational models with accurate material parameters. STATEMENT OF SIGNIFICANCE: Global mechanical characterisation techniques disregard the heterogeneous nature of atherosclerotic lesions. Previous nanoindentation results for carotid calcifications have displayed a wide range. This study evaluates calcification properties with respect to radiographic density obtained from Micro-CT images. This is the first work to characterise calcifications from peripheral lower limb arteries using nanoindentation. Results demonstrate a strong positive correlation between radiographic density and calcification mechanical properties. Characterising calcifications using their density values provides clarity on the variation in published properties for calcified tissues. Furthermore, this study confirms the hypothesis that fully calcified plaque tissue behaviour similar to that of bone. Appropriate material parameters for calcified tissues can now be employed in computational simulations.