Evaluation of respiration-correlated digital tomosynthesis in lung

4D digital tomosynthesis image reconstruction using brute force-based adaptive total variation (BF-ATV) in a prototype LINAC system

Respiratory-correlated cone-beam CT (CBCT) not only inhibits rapid scanning due to the slow speed of the LINAC head gantry rotation, but its implementation for routine patient imaging is impractical because of the high radiation dose delivered during the process. Digital tomosynthesis (DTS) is a potentially faster technique that delivers a much lower radiation dose by reducing the number of projections in a limited angular range. Unfortunately, 4D-DTS introduces strong aliasing artifacts in the reconstructed images due to the sparsely sampled projections in each respiratory phase bin. The authors hereby suggest a novel low-dose 4D-DTS image reconstruction method that achieves a compromise between the occurrence of aliasing artifacts and image smoothing using a brute force-based adaptive weighting parameter searching technique. We used a prototype LINAC system mounted with a flat-panel detector to acquire tomosynthesis projections of respiratory motion in a phantom in the anterior-posterior (AP) and lateral views. Three different 4D-DTS image reconstruction schemes that included conventional filtered back-projection (FBP), adaptive steepest descent projection onto convex sets (ASD-POCS), and the proposed brute force-based adaptive total variation (BF-ATV) were implemented in four different respiratory phase bins for both AP and lateral views. All reconstructions were accelerated using a single GPU card to reduce the computation time. To study the performance of the algorithm under various sparse conditions, we operated the prototype system in three different gantry sweep modes. The results indicate that the proposed BF-ATV method yields the largest structural similarities in the differenced image between the ground-truth dataset acquired using the slow gantry sweep mode and the sparse dataset from both moderate and fast sweep modes. In addition, the proposed method maintained the object sharpness with less streaking lines and small loss of sharpness compared to the conventional FBP and ASD-POCS methods. In conclusion, the proposed low-dose 4D-DTS reconstruction scheme may provide better performance due in part to its rapid scanning. Therefore, it is potentially applicable to practical 4D imaging for radiotherapy.

Model evaluation of rapid 4-dimensional lung tomosynthesis

Purpose

This is an investigation of a lung motion digital tomosynthesis (DTS) model using combined stationary detector and stationary cold cathode x-ray sources at projection acquisition rates that exceed the present norms. The intent is to reduce anatomical uncertainties from artifacts inherent in thoracic 4-dimensional computed tomography (CT).

Methods and materials

Parameters necessary to perform rapid lung 4-dimensional DTS were studied using a conventional radiographic system with linear motion of the x-ray source and a simple hypothetical hardware performance model. Hypothetical rapid imaging parameters of sweep duration, projections per second, pulse duration, and tube current (mA) were derived on the basis of 0.5 mm and 1 mm motion captures per phase, 10 and 15 breaths per minute (bpm), 10 to 40 mm breathing amplitude, and 2 signal-to-noise ratio (SNR) levels. Anterior-posterior and lateral projection images of a normal size anthropomorphic thorax phantom with iodine contrast inserts were collected and reconstructed with an algebraic algorithm to study the effects of reduced x-ray output associated with field emission cold cathodes composed of carbon nanotubes or metal Spindt-type. Radiographic projections were collected at 3 SNR levels that were set at standard clinical DTS milliampere-seconds (mAs) and reduced corresponding to 50% and 25% standard DTS mAs to simulate a reduced x-ray output.

Results

The DTS SNR of the inserts was superior in all reconstructions at clinical mAs versus automatic exposure-control radiographs and superior in 3 of 4 at the 50% and 25% mAs levels. The most demanding performance parameters corresponding to 40 mm amplitude, 15 bpm, 0.5 mm motion capture limit, and 61 projections were sweep duration (10.4 msec), projection rate (5862 projections per second), pulse duration (0.161 msec), current 189 mA anterior-posterior, and 653 mA lateral.

Conclusions

Feasibility depends on the output performance of stationary cold cathode hardware being developed for DTS. Present image receptor technology can accommodate frame acquisition rates.

Clinical Study of Orthogonal-View Phase-Matched Digital Tomosynthesis for Lung Tumor Localization

Background and Purpose:

Compared to cone-beam computed tomography, digital tomosynthesis imaging has the benefits of shorter scanning time, less imaging dose, and better mechanical clearance for tumor localization in radiation therapy. However, for lung tumors, the localization accuracy of the conventional digital tomosynthesis technique is affected by the lack of depth information and the existence of lung tumor motion. This study investigates the clinical feasibility of using an orthogonal-view phase-matched digital tomosynthesis technique to improve the accuracy of lung tumor localization.

Materials and Methods:

The proposed orthogonal-view phase-matched digital tomosynthesis technique benefits from 2 major features: (1) it acquires orthogonal-view projections to improve the depth information in reconstructed digital tomosynthesis images and (2) it applies respiratory phase-matching to incorporate patient motion information into the synthesized reference digital tomosynthesis sets, which helps to improve the localization accuracy of moving lung tumors. A retrospective study enrolling 14 patients was performed to evaluate the accuracy of the orthogonal-view phase-matched digital tomosynthesis technique. Phantom studies were also performed using an anthropomorphic phantom to investigate the feasibility of using intratreatment aggregated kV and beams’ eye view cine MV projections for orthogonal-view phase-matched digital tomosynthesis imaging. The localization accuracy of the orthogonal-view phase-matched digital tomosynthesis technique was compared to that of the single-view digital tomosynthesis techniques and the digital tomosynthesis techniques without phase-matching.

Results:

The orthogonal-view phase-matched digital tomosynthesis technique outperforms the other digital tomosynthesis techniques in tumor localization accuracy for both the patient study and the phantom study. For the patient study, the orthogonal-view phase-matched digital tomosynthesis technique localizes the tumor to an average (± standard deviation) error of 1.8 (0.7) mm for a 30° total scan angle. For the phantom study using aggregated kV–MV projections, the orthogonal-view phase-matched digital tomosynthesis localizes the tumor to an average error within 1 mm for varying magnitudes of scan angles.

Conclusion:

The pilot clinical study shows that the orthogonal-view phase-matched digital tomosynthesis technique enables fast and accurate localization of moving lung tumors.

Estimating 4D-CBCT from prior information and extremely limited angle projections using structural PCA and weighted free-form deformation for lung radiotherapy

PURPOSE

To investigate the feasibility of using structural-based principal component analysis (PCA) motion-modeling and weighted free-form deformation to estimate on-board 4D-CBCT using prior information and extremely limited angle projections for potential 4D target verification of lung radiotherapy.

METHODS

A technique for lung 4D-CBCT reconstruction has been previously developed using a deformation field map (DFM)-based strategy. In the previous method, each phase of the 4D-CBCT was generated by deforming a prior CT volume. The DFM was solved by a motion model extracted by a global PCA and free-form deformation (GMM-FD) technique, using a data fidelity constraint and deformation energy minimization. In this study, a new structural PCA method was developed to build a structural motion model (SMM) by accounting for potential relative motion pattern changes between different anatomical structures from simulation to treatment. The motion model extracted from planning 4DCT was divided into two structures: tumor and body excluding tumor, and the parameters of both structures were optimized together. Weighted free-form deformation (WFD) was employed afterwards to introduce flexibility in adjusting the weightings of different structures in the data fidelity constraint based on clinical interests. XCAT (computerized patient model) simulation with a 30 mm diameter lesion was simulated with various anatomical and respiratory changes from planning 4D-CT to on-board volume to evaluate the method. The estimation accuracy was evaluated by the volume percent difference (VPD)/center-of-mass-shift (COMS) between lesions in the estimated and "ground-truth" on-board 4D-CBCT. Different on-board projection acquisition scenarios and projection noise levels were simulated to investigate their effects on the estimation accuracy. The method was also evaluated against three lung patients.

RESULTS

The SMM-WFD method achieved substantially better accuracy than the GMM-FD method for CBCT estimation using extremely small scan angles or projections. Using orthogonal 15° scanning angles, the VPD/COMS were 3.47 ± 2.94% and 0.23 ± 0.22 mm for SMM-WFD and 25.23 ± 19.01% and 2.58 ± 2.54 mm for GMM-FD among all eight XCAT scenarios. Compared to GMM-FD, SMM-WFD was more robust against reduction of the scanning angles down to orthogonal 10° with VPD/COMS of 6.21 ± 5.61% and 0.39 ± 0.49 mm, and more robust against reduction of projection numbers down to only 8 projections in total for both orthogonal-view 30° and orthogonal-view 15° scan angles. SMM-WFD method was also more robust than the GMM-FD method against increasing levels of noise in the projection images. Additionally, the SMM-WFD technique provided better tumor estimation for all three lung patients compared to the GMM-FD technique.

CONCLUSION

Compared to the GMM-FD technique, the SMM-WFD technique can substantially improve the 4D-CBCT estimation accuracy using extremely small scan angles and low number of projections to provide fast low dose 4D target verification.

A software tool of digital tomosynthesis application for patient positioning in radiotherapy

Digital Tomosynthesis (DTS) is an image modality in reconstructing tomographic images from two‐dimensional kV projections covering a narrow scan angles. Comparing with conventional cone‐beam CT (CBCT), it requires less time and radiation dose in data acquisition. It is feasible to apply this technique in patient positioning in radiotherapy. To facilitate its clinical application, a software tool was developed and the reconstruction processes were accelerated by graphic processing unit (GPU). Two reconstruction and two registration processes are required for DTS application which is different from conventional CBCT application which requires one image reconstruction process and one image registration process. The reconstruction stage consists of productions of two types of DTS. One type of DTS is reconstructed from cone‐beam (CB) projections covering a narrow scan angle and is named onboard DTS (ODTS), which represents the real patient position in treatment room. Another type of DTS is reconstructed from digitally reconstructed radiography (DRR) and is named reference DTS (RDTS), which represents the ideal patient position in treatment room. Prior to the reconstruction of RDTS, The DRRs are reconstructed from planning CT using the same acquisition setting of CB projections. The registration stage consists of two matching processes between ODTS and RDTS. The target shift in lateral and longitudinal axes are obtained from the matching between ODTS and RDTS in coronal view, while the target shift in longitudinal and vertical axes are obtained from the matching between ODTS and RDTS in sagittal view. In this software, both DRR and DTS reconstruction algorithms were implemented on GPU environments for acceleration purpose. The comprehensive evaluation of this software tool was performed including geometric accuracy, image quality, registration accuracy, and reconstruction efficiency. The average correlation coefficient between DRR/DTS generated by GPU‐based algorithm and CPU‐based algorithm is 0.99. Based on the measurements of cube phantom on DTS, the geometric errors are within 0.5 mm in three axes. For both cube phantom and pelvic phantom, the registration errors are within 0.5 mm in three axes. Compared with reconstruction performance of CPU‐based algorithms, the performances of DRR and DTS reconstructions are improved by a factor of 15 to 20. A GPU‐based software tool was developed for DTS application for patient positioning of radiotherapy. The geometric and registration accuracy met the clinical requirement in patient setup of radiotherapy. The high performance of DRR and DTS reconstruction algorithms was achieved by the GPU‐based computation environments. It is a useful software tool for researcher and clinician in evaluating DTS application in patient positioning of radiotherapy.

PACS number(s): 87.57.nf

Sub-millimeter spine position monitoring for stereotactic body radiotherapy using offline digital tomosynthesis

PURPOSE

Spine stereotactic radiotherapy (SBRT) requires intrafraction motion <1-2mm. We evaluated the accuracy and precision of digital tomosynthesis (DTS) in combination with triangulation for spine position tracking.

MATERIALS/METHODS

Single-slice DTS images were generated from kV cone beam CT (CBCT) projection images. They were registered to reference DTS images reconstructed from the planning CT-scan to determine 2D shifts between actual patient position and treatment plan position. 3D spine position was obtained by triangulation of each registration with a previous registration, for every 1° of data. For 7 patients who underwent spine SBRT, the standard deviation (SD) of DTS+triangulation over one entire dataset was evaluated for different DTS angles (2-16°) and triangulation angles (1-46°). For 32 CBCT datasets, acquired before or after treatment of the 7 patients, using 4° DTS and 18° triangulation angle, SDs were determined and average positions were compared to clinically performed CBCT registrations.

RESULTS

Mean SDs were 0.29±0.10mm for lateral (range 0.1-0.55mm), 0.14±0.08 for longitudinal (0.05-0.39) and 0.24±0.10 for the vertical direction (0.10-0.57). Lateral and vertical SDs for thoracic spine were higher than for lumbar spine. Differences between clinical CBCT registration and DTS+triangulation were 0.1±0.26, 0.02±0.33 and -0.07±0.21mm.

CONCLUSION

The combination of DTS and triangulation allows for monitoring spine position with sub-mm accuracy and precision.

Preliminary clinical evaluation of a 4D-CBCT estimation technique using prior information and limited-angle projections

BACKGROUND AND PURPOSE

A technique has been previously reported to estimate high-quality 4D-CBCT using prior information and limited-angle projections. This study is to investigate its clinical feasibility through both phantom and patient studies.

MATERIALS AND METHODS

The new technique used to estimate 4D-CBCT is called MMFD-NCC. It is based on the previously reported motion modeling and free-form deformation (MMFD) method, with the introduction of normalized-cross-correlation (NCC) as a new similarity metric. The clinical feasibility of this technique was evaluated by assessing the accuracy of estimated anatomical structures in comparison to those in the 'ground-truth' reference 4D-CBCTs, using data obtained from a physical phantom and three lung cancer patients. Both volume percentage error (VPE) and center-of-mass error (COME) of the estimated tumor volume were used as the evaluation metrics.

RESULTS

The average VPE/COME of the tumor in the prior image was 257.1%/10.1 mm for the phantom study and 55.6%/3.8 mm for the patient study. Using only orthogonal-view 30° projections, the MMFD-NCC has reduced the corresponding values to 7.7%/1.2 mm and 9.6%/1.1 mm, respectively.

CONCLUSION

The MMFD-NCC technique is able to estimate 4D-CBCT images with geometrical accuracy of the tumor within 10% VPE and 2 mm COME, which can be used to improve the localization accuracy of radiotherapy.

Digital tomosynthesis of the chest: current and emerging applications

Digital tomosynthesis (DTS) of the chest is a technique whose basic components are similar to those of digital radiography, but that also provides some of the benefits of computed tomography (CT). The major advantages of DTS over conventional chest radiography are improved visibility of the pulmonary parenchyma and depiction of abnormalities such as pulmonary nodules. Calcifications, vessels, airways, and chest wall abnormalities are also much more readily visualized at DTS than at chest radiography. DTS could potentially be combined with chest radiography to follow up known nodules, confirm or rule out suspected nodules seen at radiography, or evaluate individuals who are at high risk for lung cancer or pulmonary metastases. DTS generates coronal "slices" through the chest whose resolution is superior to that of coronal reconstructed CT images, but it is limited by its suboptimal depth resolution and susceptibility to motion; consequently, potential pitfalls in recognizing lesions adjacent to the pleura, diaphragm, central vessels, and mediastinum can occur. However, the radiation dose and projected cost of chest DTS are lower than those of standard chest CT. Besides pulmonary nodule detection, specific applications of DTS that are under investigation include evaluation of pulmonary tuberculous and nontuberculous mycobacterial disease, cystic fibrosis, interstitial lung disease, and asbestos-related thoracic diseases. A basic understanding of chest DTS and of the emerging applications of this technique can prove useful to the radiologist. Online supplemental material is available for this article.

Four dimensional digital tomosynthesis using on-board imager for the verification of respiratory motion

Purpose

To evaluate respiratory motion of a patient by generating four-dimensional digital tomosynthesis (4D DTS), extracting respiratory signal from patients' on-board projection data, and ensuring the feasibility of 4D DTS as a localization tool for the targets which have respiratory movement.

Methods and Materials

Four patients with lung and liver cancer were included to verify the feasibility of 4D-DTS with an on-board imager. CBCT acquisition (650–670 projections) was used to reconstruct 4D DTS images and the breath signal of the patients was generated by extracting the motion of diaphragm during data acquisition. Based on the extracted signal, the projection data was divided into four phases: peak-exhale phase, mid-inhale phase, peak-inhale phase, and mid-exhale phase. The binned projection data was then used to generate 4D DTS, where the total scan angle was assigned as ±22.5° from rotation center, centered on 0° and 180° for coronal “half-fan” 4D DTS, and 90° and 270° for sagittal “half-fan” 4D DTS. The result was then compared with 4D CBCT which we have also generated with the same phase distribution.

Results

The motion of the diaphragm was evident from the 4D DTS results for peak-exhale, mid-inhale, peak-inhale and mid-exhale phase assignment which was absent in 3D DTS. Compared to the result of 4D CBCT, the view aliasing effect due to arbitrary angle reconstruction was less severe. In addition, the severity of metal artifacts, the image distortion due to presence of metal, was less than that of the 4D CBCT results.

Conclusion

We have implemented on-board 4D DTS on patients data to visualize the movement of anatomy due to respiratory motion. The results indicate that 4D-DTS could be a promising alternative to 4D CBCT for acquiring the respiratory motion of internal organs just prior to radiotherapy treatment.

A technique for estimating 4D-CBCT using prior knowledge and limited-angle projections

PURPOSE

To develop a technique to estimate onboard 4D-CBCT using prior information and limited-angle projections for potential 4D target verification of lung radiotherapy.

METHODS

Each phase of onboard 4D-CBCT is considered as a deformation from one selected phase (prior volume) of the planning 4D-CT. The deformation field maps (DFMs) are solved using a motion modeling and free-form deformation (MM-FD) technique. In the MM-FD technique, the DFMs are estimated using a motion model which is extracted from planning 4D-CT based on principal component analysis (PCA). The motion model parameters are optimized by matching the digitally reconstructed radiographs of the deformed volumes to the limited-angle onboard projections (data fidelity constraint). Afterward, the estimated DFMs are fine-tuned using a FD model based on data fidelity constraint and deformation energy minimization. The 4D digital extended-cardiac-torso phantom was used to evaluate the MM-FD technique. A lung patient with a 30 mm diameter lesion was simulated with various anatomical and respirational changes from planning 4D-CT to onboard volume, including changes of respiration amplitude, lesion size and lesion average-position, and phase shift between lesion and body respiratory cycle. The lesions were contoured in both the estimated and "ground-truth" onboard 4D-CBCT for comparison. 3D volume percentage-difference (VPD) and center-of-mass shift (COMS) were calculated to evaluate the estimation accuracy of three techniques: MM-FD, MM-only, and FD-only. Different onboard projection acquisition scenarios and projection noise levels were simulated to investigate their effects on the estimation accuracy.

RESULTS

For all simulated patient and projection acquisition scenarios, the mean VPD (±S.D.)∕COMS (±S.D.) between lesions in prior images and "ground-truth" onboard images were 136.11% (±42.76%)∕15.5 mm (±3.9 mm). Using orthogonal-view 15°-each scan angle, the mean VPD∕COMS between the lesion in estimated and "ground-truth" onboard images for MM-only, FD-only, and MM-FD techniques were 60.10% (±27.17%)∕4.9 mm (±3.0 mm), 96.07% (±31.48%)∕12.1 mm (±3.9 mm) and 11.45% (±9.37%)∕1.3 mm (±1.3 mm), respectively. For orthogonal-view 30°-each scan angle, the corresponding results were 59.16% (±26.66%)∕4.9 mm (±3.0 mm), 75.98% (±27.21%)∕9.9 mm (±4.0 mm), and 5.22% (±2.12%)∕0.5 mm (±0.4 mm). For single-view scan angles of 3°, 30°, and 60°, the results for MM-FD technique were 32.77% (±17.87%)∕3.2 mm (±2.2 mm), 24.57% (±18.18%)∕2.9 mm (±2.0 mm), and 10.48% (±9.50%)∕1.1 mm (±1.3 mm), respectively. For projection angular-sampling-intervals of 0.6°, 1.2°, and 2.5° with the orthogonal-view 30°-each scan angle, the MM-FD technique generated similar VPD (maximum deviation 2.91%) and COMS (maximum deviation 0.6 mm), while sparser sampling yielded larger VPD∕COMS. With equal number of projections, the estimation results using scattered 360° scan angle were slightly better than those using orthogonal-view 30°-each scan angle. The estimation accuracy of MM-FD technique declined as noise level increased.

CONCLUSIONS

The MM-FD technique substantially improves the estimation accuracy for onboard 4D-CBCT using prior planning 4D-CT and limited-angle projections, compared to the MM-only and FD-only techniques. It can potentially be used for the inter/intrafractional 4D-localization verification.

Digital tomosynthesis (DTS) for verification of target position in early stage lung cancer patients

PURPOSE

The ability to verify intrafraction tumor position is clinically useful for hypofractionated treatments. Short arc kV digital tomosynthesis (DTS) could facilitate more frequent target verification. The authors used DTS combined with triangulation to determine the mean temporal position of small-volume lung tumor targets treated with stereotactic radiotherapy. DTS registration results were benchmarked against online clinical localization using registration between free-breathing cone-beam computed tomography (CBCT) and the average intensity projection (AvIP) of the planning 4DCT.

METHODS

In this retrospective study, 76 sets of kV-projection images from online CBCT scans of 13 patients were used to generate DTS image slices (CB-DTS) with nonclinical research software (DTS Toolkit, Varian Medical Systems). Three-dimensional tumor motion was 1.3-4 mm in six patients and 6.1-25.4 mm in seven patients on 4DCT (significant difference in the mean of the groups, P < 0.01). The 4DCT AvIP was used to digitally reconstruct the Reference-DTS. DTS registration and DTS registration combined with triangulation were investigated. Progressive shortening of total DTS arc lengths from 95° to 35° around 0° gantry position was evaluated for different scenarios: DTS registration using the entire arc; DTS registration plus triangulation using two nonoverlapping arcs; and for 55° and 45° total gantry rotation, DTS registration plus triangulation using two overlapping arcs. Finally, DTS registration plus triangulation performed at eight gantry angles, each separated by 45° was evaluated using full fan kV projection data for one patient with an immobile tumor and five patients with mobile tumors.

RESULTS

For DTS registration alone, shortening arc length did not influence accuracy in X- and Y-directions, but in Z-direction, mean deviations from online CBCT localization systematically increased for shorter arc length (P < 0.05). For example, using a 95° arc mean DTS-CBCT difference was 0.8 mm (1 SD = 0.6 mm) and for a 35° arc the mean was 2.4 mm (1 SD = 1.7 mm). DTS plus triangulation using nonoverlapping-arcs increased accuracy in Z-direction for tested arc lengths ≤55° (P < 0.01). Overlapping arcs increased accuracy in Y-direction for tumors with motion >4 mm (P < 0.02) but increased Z-direction accuracy was only observed with 55° total gantry rotation. The 95th percentile deviations with this overlapping technique in X-, Y-, and Z-directions were 1.3, 2.0, and 2.5 mm, respectively. For the five patients with mobile tumors where DTS + triangulation was performed with 45° intervals, the pooled deviation from online CBCT correction showed, for X-, Y-, and Z-directions, mean of 1.1 mm, standard deviations (SD) of 0.9, 1.0, and 0.9 mm, respectively. The mean + 2 SD was <3 mm for each direction.

CONCLUSIONS

Short-arc DTS verification of time averaged lung tumor position is feasible using free-breathing kV projection data and the AvIP of the 4DCT as a reference. Observed differences between DTS and online CBCT registration with AvIP were ≤3 mm (mean + 2 SD), however, the increased temporal resolution of DTS + triangulation also identified short period deviations from the average target position on the CBCT. Short-arc DTS appears promising for intrafraction tumor position monitoring during stereotactic lung radiotherapy delivered with a rotational technique.

Respiration-phase-matched digital tomosynthesis imaging for moving target verification: a feasibility study

PURPOSE

To develop a respiration-phase-matched digital tomosynthesis (DTS) technique to monitor moving targets, and to evaluate its accuracy for various imaging parameters and anatomical characteristics.

METHODS

Previously developed 3D-DTS techniques, registering onboard DTS (OB-DTS, reconstructed from onboard projections) to reference DTS (R-DTS, reconstructed from DRRs of 3D reference CT), are inadequate to monitor moving targets. The authors' proposed respiration-phase-matched DTS technique registers OB-DTS to R-DTS reconstructed from DRRs generated by the same phase images of 4D reference CT as the corresponding onboard projections. To evaluate the improved accuracy of the author's technique, the authors performed thoracic phantom studies using (1) simulation with the 4D digital extended-cardiac-torso (XCAT) phantom, and (2) experiments with an anthropomorphic motion phantom. The studies were performed for various: respiratory cycle (RC), scan angle, and fraction of RC contained therein. Also, the authors assessed the accuracy of their technique relative to target size/location, and respiration inconsistencies from the R-DTS to OB-DTS.

RESULTS

In both simulation and experimental studies, the respiration-phase-matched DTS technique is significantly more accurate in determining moving target positions. For 324 different scenarios simulated by XCAT, the respiration-phase-matched DTS technique localizes the 3D target position to errors of 1.07 ± 0.57 mm (mean ± S.D.), as compared to (a) 2.58 ± 1.37 and (b) 7.37 ± 4.18 mm, for 3D-DTS using 3D reference CT of (a) average intensity projection and (b) free-breathing CT. For 60 scenarios evaluated through experimental study, the uncertainties corresponding to those above are 1.24 ± 0.87, 2.42 ± 1.80, and 5.77 ± 6.45 mm, respectively. For a given scan angle, the accuracy of respiration-phase-matched DTS technique is less dependent on RC and the fraction of RC included in the scan. Increasing scan angle improves its accuracy. For different target locations, the targets near the chest wall or in the middle of lung provide higher registration accuracy compared to those near the mediastinum and diaphragm. Larger targets provide higher registration accuracy than small targets. Different respiratory cycle inconsistencies from R-DTS to OB-DTS minimally affect the registration accuracy. Increasing the respiratory amplitude inconsistencies will decrease the accuracy.

CONCLUSIONS

The respiration-phase-matched DTS is more accurate and robust in determining moving target positions than 3D-DTS. It has potential application in pretreatment setup, post-treatment analysis, and intrafractional target verification.

Comparison of chest digital tomosynthesis and chest radiography for detection of asbestos-related pleuropulmonary disease

AIM

To compare chest digital tomosynthesis (DTS) with digital radiography for the detection of asbestos-related pleuropulmonary disease.

MATERIALS AND METHODS

The institutional review board approved this study and all participants gave informed consent. Forty-five participants with a history of asbestos exposure were examined with DTS and radiography. Low-dose multidetector computed tomography (CT) in the prone position served as the reference. Two observers evaluated all images for the presence of pleural abnormalities and asbestosis. Interobserver agreement was analysed by using the k statistic. Diagnostic performance of the two imaging methods was compared using McNemar's test.

RESULTS

Interobserver agreement regarding DTS findings was moderate to very good (k = 0.544-0.846) and superior to the radiographic findings (k = 0.236-1.000). Overall, the diagnostic accuracy of DTS for the lesion detection was significantly better than with radiography (all p < 0.05, except that for the comparison of diagnostic accuracy of DTS versus radiographic detection of left diaphragmatic plaques and asbestosis). DTS was more sensitive than radiography for the detection of asbestosis (82% versus 27%, p = 0.031).

CONCLUSION

DTS is more accurate than radiography in the detection of pleural plaques and more sensitive than radiography in the detection of asbestosis. Interobserver agreements with respect to the DTS findings were superior to the radiographic findings.

Four-dimensional cone-beam computed tomography and digital tomosynthesis reconstructions using respiratory signals extracted from transcutaneously inserted metal markers for liver SBRT

PURPOSE

Respiration-induced intrafraction target motion is a concern in liver cancer radiotherapy, especially in stereotactic body radiotherapy (SBRT), and therefore, verification of its motion is necessary. An effective means to localize the liver cancer is to insert metal fiducial markers to or near the tumor with simultaneous imaging using cone-beam computed tomography (CBCT). Utilizing the fiducial markers, the authors have demonstrated a method to generate breath-induced motion signal of liver for reconstructing 4D digital tomosynthesis (4DDTS) and 4DCBCT images based on phasewise and/or amplitudewise sorting of projection data.

METHODS

The marker extraction algorithm is based on template matching of a prior known marker image and has been coded to optimally extract marker positions in CBCT projections from the On-Board Imager (Varian Medical Systems, Palo Alto, CA). To validate the algorithm, multiple projection images of moving thorax phantom and five patient cases were examined. Upon extraction of the motion signals from the markers, 4D image sorting and image reconstructions were subsequently performed. In the case of incomplete signals due to projections with missing markers, the authors have implemented signal profiling to replace the missing portion.

RESULTS

The proposed marker extraction algorithm was shown to be very robust and accurate in the phantom and patient cases examined. The maximum discrepancy of the algorithm predicted marker location versus operator selected location was < 1.2 mm, with the overall average of 0.51 +/- 0.15 mm, for 500 projections. The resulting 4DDTS and 4DCBCT images showed clear reduction in motion-induced blur of the markers and the anatomy for an effective image guidance. The signal profiling method was useful in replacing missing signals.

CONCLUSIONS

The authors have successfully demonstrated that motion tracking of fiducial markers and the subsequent 4D reconstruction of CBCT and DTS are possible. Due to the significant reduction in motion-induced image blur, it is anticipated that such technology will be useful in image-guided liver SBRT treatments.