Increased beam attenuation and surface dose by different couch inserts of treatment tables used in megavoltage radiotherapy

Dosimetric characterization of foam padding with posterior fields in palliative radiation therapy

Patients undergoing external beam radiation therapy for the palliative treatment of painful bony metastases may have difficulty maintaining a still position on a rigid uncovered couch top, both during CT simulation as well as during patient setup, image guidance, and treatment on the linear accelerator. For these patients, a thin foam pad or mattress is sometimes used to mitigate patient discomfort. It was desired to quantify the effect of the padding in cases in which the patient is to be treated supine with posterior beams when the majority of the beam weighting traverses both the couch and the pad. Ion chamber measurements in-phantom were acquired with 6 MV, 10 MV, and 15 MV photon beams. At depths of maximum dose, the pad resulted in a difference of signal collected ≤1%. At the phantom surface, the pad resulted in an increase in signal ranging from 1% to 6.5% for the measured beams. CT data of the pad, both with and without applied pressure, indicated that the pad had average HU values close to air.

Radiation dosimetry effect evaluation of a carbon fiber couch on novel uRT-linac 506c accelerator

Recently, a diagnostic helical CT is integrated into a linear accelerator, called uRT-linac 506c, whose CT scanning dataset can be directly used to do simulation. This novel structure provides a possibility for online adaptive radiotherapy. For adaptive radiotherapy, the carbon fiber couch is an essential external device for supporting and positioning patients. And the effect on dose attenuation and distribution caused by a couch is inevitable and vital for precise treatment. In this research, the couch equipped with uRT-linac 506c was evaluated on the radiation dosimetry effect. The treatment couch equipped on the uRT-linac 506c accelerator was evaluated, and its effect on the attenuation, surface dose and dose buildup were measured for different phantom positions (offset = 0 cm, offset =  + 10 cm and offset =  − 10 cm, respectively) and different gantry angles. Since uRT-linac 506c is exclusively capable to provide diagnostic CT scanning data with real relative electron density (RED), this CT scanning data of the couch can be used directly in uRT-TPS to design plans. This scanned couch dataset was designated as the model A. The model B was a dummy structure of a treatment couch inserted with artificially preset RED. The dose calculation accuracy of these two models was compared using PB, CC, and MC on uRT-TPS. With the effect of carbon fiber couch, the surface dose was increased at least 97.94% for 25 × 25 cm² field and 188.83% for 10 × 10 cm² field, compared with those without. At different phantom positions (offset = 0, + 10, − 10 cm), the attenuation for 6 MV photon beam at gantry angle 180° were 4.4%, 4.4%, and 4.3%, respectively, and varied with changes of gantry angle. There do exists dose deviation between measurement and TPS calculation with the involvement of treatment couch, among the three algorithms, MC presented the least deviation, and the model A made less and steadier deviation than the model B, showing promising superiority. The attenuation, surface dose, and buildup effects of the carbon fiber couch in this study were measured similarly to most counterparts. The dose deviation calculated based on the couch dataset scanned by the diagnostic helical CT was smaller than those based on a dummy couch. This result suggests that an accelerator equipped with a diagnostic CT, which can help reduce the dose deviation of the carbon fiber couch, is a promising platform for online adaptive radiotherapy.

The effect of carbon fibre treatment couch with and without immobilisation devices on radiotherapy dose calculation using three different planning algorithms and photon beam energies

Introduction:

The objective of radiotherapy immobilisation devices is to improve the reproducibility of patient positioning during treatment sessions. The inclusion of these devices in the treatment protocol may increase the skin dose. In practice, these devices are not systematically taken into account in the dose calculation.

Material and methods:

In this study, the dosimetric effects of the carbon fibre couch iBEAM Evo Extension 415, with and without three different immobilisation devices (a Klarity Breastboard R610-2ECF, a Bionix Butterfly Board and CIVCO Vac-Lok vacuum bag), were calculated and evaluated on the dose calculation for conformal three-dimensional radiation therapy. The measurements were carried out by comparing the measured dose with the one calculated for three different algorithms, FFT convolution, fast superposition and superposition algorithms, which are implemented in Xio treatment planning system (TPS).

Results:

Dosimetric tolerance levels have been respected for specific dose calculations, which do not include the fibre couch with or without immobilisation devices. Errors of up to 8% in the dose calculation were obtained for the beams passing through the fibre couch and the breast board base support region.

Conclusion:

According to the significant attenuation differences of the beam by the fibre couch and immobilisation devices, it was concluded that ignoring the device in the dose calculation can change patient’s skin and target doses. The fibre couch and immobilisation device should be included within external body contour to account for the TPS calculation algorithms dose attenuation.

Dosimetric Evaluation of the QFix kVueTM Calypso Couch Top

PURPOSE

To evaluate the dosimetric accuracy of the default couch model of the QFix kVueTM Calypso couch top in the treatment planning system.

METHODS

With the gantry 180°, field size 20 × 20 cm, 6 MV, we measured the depth dose, off-axis dose, and dose plane of different depths in the phantom with the couch rails in and out, respectively. Isocenter doses at different angles were also obtained. The results were compared to the doses calculated using the default couch top model and the real scanned couch top model. Then we revised the default model according to the measured results.

RESULTS

With "Rails In," the depth dose, off-axis dose, and dose plane of the default couch top model had a big difference with the dose of the real scanned couch top model and the measured result. The dose of the real scanned couch top model was much closer to the measured result, but in the region of the rail edge, the difference was still significant. With "Rails Out," there was a minor difference between the measured result, the dose of the default couch top model and the real scanned couch top model. The difference between the measurement and the default couch top model became very small after being revised.

CONCLUSIONS

It is better to avoid the beam angle passing through the couch rails in treatment plans, or you should revise the parameter of the QFix kVueTM Calypso couch top model based on the measured results, and verify the treatment plan before clinical practice.

Estimation of effective imaging dose and excess absolute risk of secondary cancer incidence for four-dimensional cone-beam computed tomography acquisition

This study was conducted to estimate the organ equivalent dose and effective imaging dose for four-dimensional cone-beam computed tomography (4D-CBCT) using a Monte Carlo simulation, and to evaluate the excess absolute risk (EAR) of secondary cancer incidence. The EGSnrc/BEAMnrc were used to simulate the on-board imager (OBI) from the TrueBeam linear accelerator. Specifically, the OBI was modeled based on the percent depth dose and the off-center ratio was measured using a three-dimensional (3D) water phantom. For clinical cases, 15 lung and liver cancer patients were simulated using the EGSnrc/DOSXYZnrc. The mean absorbed doses to the lung, stomach, bone marrow, esophagus, liver, thyroid, bone surface, skin, adrenal glands, gallbladder, heart, intestine, kidney, pancreas and spleen, were quantified using a treatment planning system, and the equivalent doses to each organ were calculated. Subsequently, the effective dose was calculated as the weighted sum of the equivalent dose, and the EAR of the secondary cancer incidence was determined for each organ with the use of the biologic effects of ionizing radiation (BEIR) VII model. The effective doses were 3.9 ± 0.5, 15.7 ± 2.0, and 7.3 ± 0.9 mSv, for the lung, and 4.2 ± 0.6, 16.7 ± 2.4, and 7.8 ± 1.1 mSv, for the liver in the respective cases of the 3D-CBCT (thorax, pelvis) and 4D-CBCT modes. The lung EARs for males and females were 7.3 and 10.7 cases per million person-years, whereas the liver EARs were 9.9 and 4.5 cases per million person-years. The EAR increased with increasing time since radiation exposure. In clinical studies, we should use 4D-CBCT based on consideration of the effective dose and EAR of secondary cancer incidence.

[Development of an In-house Couch Model to Improve Dose Attenuation Correction Accuracy for a Couch with Different Thickness in the Superior-inferior Direction]

As the couch used in external radiation therapy attenuate radiation by interaction, it is necessary to correct attenuation of radiation by inserting a couch model in the treatment planning systems. For a couch whose thickness is different in the superior-inferior direction, it is possible to perform dose calculations with an error within ±1% by using separate different couch models provided by vendors. However, it is difficult to correct attenuation correction accurately with a single couch model. In this study, we created an in-house couch model which can set couch shape and physical density in detail by acquiring CT images of actual couch. When we performed dose calculation by optimizing the physical densities of in-house and vendor couch, it was found that the difference between the measured and the calculated values can be significantly reduced by using in-house couch model. Additionally, by using in-house couch model, it is found that the dose attenuation can be corrected within ±1% for a couch whose thickness is different in the superior-inferior direction.

Couch modeling optimization for tomotherapy planning and delivery

We sought to validate new couch modeling optimization for tomotherapy planning and delivery. We constructed simplified virtual structures just above a default setting couch through a planning support system (MIM Maestro, version 8.2, MIM Software Inc, Cleveland, OH, USA). Based on ionization chamber measurements, we performed interactive optimization and determined the most appropriate physical density of these virtual structures in a treatment planning system (TPS). To validate this couch optimization, Gamma analysis and these statistical analyses between a three‐dimensional diode array QA system (ArcCHECK, Sun Nuclear, Melbourne, FL, USA) results and calculations from ionization chamber measurements were performed at 3%/2 mm criteria with a threshold of 10% in clinical QA plans. Using a virtual model consisting of a center slab density of 4.2 g/cm³ and both side slabs density of 1.9 g/cm³, we demonstrated close agreement between measured dose and the TPS calculated dose. Agreement was within 1% for all gantry angles at the isocenter and within 2% in off‐axis plans. In validation of the couch modeling in a clinical QA plan, the average gamma passing rate improved approximately 0.6%–5.1%. It was statistically significant (P < 0.05) for all treatment sites. We successfully generated an accurate couch model for a TomoTherapy TPS by interactively optimizing the physical density of the couch using a planning support system. This modeling proved to be an efficient way of correcting the dosimetric effects of the treatment couch in tomotherapy planning and delivery.

Photon beam attenuation characteristics of three commercial radiation therapy treatment couch-tops

Aim

The purpose of the study was to investigate the detailed angularly dependent attenuation characteristics of three different commercial couch-tops: Varian IGRT, Qfix kVue Standard and Qfix kVue Dose Max couch-tops used in radiation therapy.

Materials and methods

The attenuation of photon beams by the treatment couch-tops was measured using a farmer chamber inserted at the centre of a 16 cm diameter cylindrical acrylic phantom for five different photon energies: 6 MV, 6FFF MV, 10 MV, 10FFF MV and 15 MV photon beams. The Varian IGRT couch-top has three different thicknesses thus attenuation measurements were done at the three different longitudinal locations. Measurements were made with the sliding support rails of the Qfix kVue Standard and Qfix kVue Dose Max couch-tops at both ‘rails-in’ and ‘rails-out’ positions. All measurements were taken for several projections through 360° movement of the gantry and for two different field sizes; 5×5 cm2 and 10×10 cm2.

Results and findings

The results indicate that the maximum attenuation of the Varian IGRT couch-top at the thin, medium and thick portions are 5·1, 5·7 and 8·9%, respectively, the Qfix kVue Standard couch with the rails-in and rails-out are 11·2 and 13·7%, respectively, and Qfix kVue Dose Max couch-top with rails-in and rails-out are 9·7 and 13·8%, respectively. The results from this study can be used to account for the couch-top attenuation during radiation treatment planning of patients treated with these couch-tops.

Dosimetric effects of a repositioning head frame system and treatment planning system dose calculation accuracy

This work aims to study the effect on surface dose and dose distribution caused by the Elekta Fraxion cranial immobilization system. The effect of Fraxion inclusion in Elekta Monaco treatment planning system and its calculation accuracy is also checked. To study the dose attenuation, a cylindrical phantom was located over the Elekta Fraxion with an IBA CC13 ionization chamber placed in the central insert at the linac isocenter. Dose measurements at multiple gantry angles were performed for three open fields, 10 × 10 cm, 5 × 5 cm and other smaller 2 × 2 cm. Measured doses were compared with the ones calculated by Monaco. Surface dose and dose distribution in the buildup region were measured placing several Gafchromic Films EBT3 at linac CAX between the slabs of a RW3 phantom located over Fraxion and read using FilmQA Pro software. Measures were performed for two open field sizes and results were compared with Monaco calculations. Measurements show a 1% attenuation for 180° gantry angle but it can be as high as 3.4% (5 × 5 open field) for 150°/210° gantry angle, as with these angles the beam goes through the Fraxion's headrest twice. If Fraxion is not included in the calculation Monaco calculation can result in a 3% difference between measured and calculated doses, while with Fraxion in the calculation, the maximum difference is 0.9%. Fraxion increases 3.7 times the surface dose, which can be calculated by Monaco with a difference lower than 2%. Monaco also calculated correctly the PDD for both open fields (2%) when Fraxion is included in the calculation. This work shows that the attenuation varies with gantry angle. The inclusion of Fraxion in Monaco improves the calculation from 3% difference to 1% in the worst case. Furthermore, the surface dose increment and the dose in the buildup region are correctly calculated.

Absorption ratio of treatment couch and effect on surface and build-up region doses

Aim

In this study, at different fields, energies and gantry angles, treatment couch and rails dose absorption ratio and treatment couch effect on surface and build-up region doses were examined.

Background

It is assumed that radiation attenuation is minimal because the carbon fiber couches have low density and it is not generally accounted for during treatment planning. Consequently, it leads to a major dosimetric mistake.

Materials and methods

Solid water phantom was used for relative dose measurement. The measurements were done using a Farmer ion chamber with 0.6 cc volume and a parallel plane ion chamber starting from surface with 1 mm depth intervals at 10 × 10 cm² field, SSD 100 cm. Measurements were taken for situations where the beams intersect the couch and couch rails.

Results

Dose absorption ratio of carbon fiber couch obtained at gantry angle of 180° was 1.52%, 0.69%, 0.33% and 0.25% at different field sizes for 6 MV. For 15 MV, this ratio was 0.95%, 0.27%, 0.20% and 0.05%. The absorption ratio is between 3.4% and 1.22% when the beams intersect with couch rails. The couch effect increased surface dose from 14% to 70% for 6 MV and from 11.34% to 53.03% for 15 MV.

Conclusions

The results showed that the carbon fiber couch increased surface dose during posterior irradiation. Therefore, the skin-sparing effect of the high energy beams was decreased. If the effect of couch is not considered, it may cause significant differences at dose which reaches the patient and may cause tissue problems such as erythema.

An Update of Couch Effect on the Attenuation of Megavoltage Radiotherapy Beam and the Variation of Absorbed Dose in the Build-up Region

PURPOSE

Fiber carbon is the most common material used in treating couch as it causes less beam attenuation than other materials. Beam attenuation replaces build-up region, reduces skin-sparing effect and causes target volume under dosage. In this study, we aimed to evaluate beam attenuation and variation of build-up region in 550 TxT radiotherapy couch.

MATERIALS AND METHODS

In this study, we utilized cylindrical PMMA Farmer chamber, DOSE-1 electrometer and set PMMA phantom in isocenter of gantry and the Farmer chamber on the phantom. Afterwards, the gantry rotated 10°, and attenuation was assessed. To measure build-up region, we used Markus chamber, Solid water phantom and DOSE-1 electrometer. Doing so, we set Solid water phantom on isocenter of gantry and placed Markus chamber in it, then we quantified the build-up region at 0° and 180° gantry angels and compared the obtained values.

RESULTS

Notable attenuation and build-up region variation were observed in 550 TxT treatment table. The maximum rate of attenuation was 5.95% for 6 MV photon beam, at 5×5 cm² field size and 130° gantry angle, while the maximum variation was 7 mm for 6 MV photon beam at 10×10 cm² field size.

CONCLUSION

Fiber carbon caused beam attenuation and variation in the build-up region. Therefore, the application of fiber carbon is recommended for planning radiotherapy to prevent skin side effects and to decrease the risk of cancer recurrence.

A patient immobilization device for prone breast radiotherapy: Dosimetric effects and inclusion in the treatment planning system

PURPOSE

To assess the dosimetric impact of a patient positioning device for prone breast radiotherapy and assess the accuracy of a treatment planning system (TPS) in predicting this impact.

METHODS

Beam attenuation and build-up dose perturbations, quantified by ionization chamber and radiochromic film dosimetry, were evaluated for 3 components of the patient positioning device: the carbon fiber baseplate, the support cushions and the support wedge for the contralateral breast. Dose calculations were performed using the XVMC dose engine implemented in the Monaco TPS. All components were included during planning CT acquisition.

RESULTS

Beam attenuation amounted to 7.57% (6MV) and 5.33% (15MV) for beams obliquely intersecting the couchtop-baseplate combination. Beams traversing large sections of the support wedge were attenuated by 12.28% (6MV) and 9.37% (15MV). For the support cushion foam, beam attenuation remained limited to 0.11% (6MV) and 0.08% (15MV) per centimeter thickness. A substantial loss of dose build-up was detected when irradiating through any of the investigated components. TPS dose calculations accurately predicted beam attenuation by the baseplate and support wedge. A manual density overwrite was needed to model attenuation by the support cushion foam. TPS dose calculations in build-up regions differed considerably from measurements for both open beams and beams traversing the device components.

CONCLUSIONS

Irradiating through the components of the positioning device resulted in a considerable degradation of skin sparing. Inclusion of the device components in the treatment planning CT allowed to accurately model the most important attenuation effect, but failed to accurately predict build-up doses.

[Optimization of Couch Modeling in the Change of Dose Calculation Methods and Their Versions]

In external radiotherapy, the X-ray beam passes through the treatment couch, leading to the dose reduction by the attenuation of the couch. As a method to compensate for the reduction, radiation treatment planning systems (RTPS) support virtual couch function, namely "couch modeling method". In the couch modeling method, the computed tomography (CT) numbers assigned to each structure should be optimized by comparing calculations to measurements for accurate dose calculation. Thus, re-optimization of CT numbers will be required when the dose calculation algorithm or their version changes. The purpose of this study is to evaluate the calculation accuracy of the couch modeling method in different calculation algorithms and their versions. The optimal CT numbers were determined by minimizing the difference between measured transmission factors and calculated ones. When CT numbers optimized by Anisotropic Analytical Algorithm (AAA) Ver. 8.6 were used, the maximum and the mean difference of transmission factor were 5.8% and 1.5%, respectively, for Acuros XB (AXB) Ver. 11.0. However, when CT numbers optimized by AXB Ver. 11.0 were used, they were 2.6% and 0.6%, respectively. The CT numbers for couch structures should be optimized when changing dose calculation algorithms and their versions. From the comparison of the measured transmission to calculation, it was found that the CT numbers had high accuracy.

Effects of Siemens TT-D carbon fiber table top on beam attenuation, and build up region of 6 MV photon beam

AIM

This study deals with Monte Carlo simulations of the effects which the 550 TXT carbon fiber couch can have on the relevant parameters of a 6 MV clinical photon beam in three field sizes.

BACKGROUND

According to the reports issued by the International Commission on Radiation Units and Measurements (ICRU), the calculated dose across a high gradient distribution should be within 2% of the relative dose, or within 0.2 cm of the isodose curve position in the target volume. Nowadays, the use of posterior oblique beam has become a common practice. It is clear that, in radiotherapy, the presence of the couch affects the beam intensity and, as a result, the skin dose.

MATERIALS AND METHODS

Firstly, Siemens linear accelerator validation for 6 MV photon beam was performed, and satisfactory agreement between Monte Carlo and experimental data for various field sizes was observed. Secondly, the couch transmission factor for the reference field size and depth was computed, and the skin dose enhancement by the couch was assessed.

RESULTS

The largest impact of the carbon fiber couch effect was observed for the 5 × 5 cm2 field size. Such evaluation has not been reported for this couch before.

CONCLUSION

Despite providing minimal attenuation for the primary radiation, the assumption that carbon fiber couches are radiotranslucent is not valid, and the effects of couches of this type on the transmission factor, and on the skin dose should be carefully investigated for each field size and depth.

Radiotherapy couches: is kevlar an obstacle? Attenuation study of three different tabletops

Introduction

Treatment tabletops are usually made of carbon fibre due to its high mechanical strength and rigidity, low specific density, extremely light and regularly considered radiotranslucent. Our clinic acquired a Calypso 4D Localization System where electromagnetic (EM) frequencies to detect implanted transponders in the patient are used. Carbon fibre is an electrical conductive material which interferes with EM frequencies. Therefore, in order to be able to use the Calypso System the carbon fibre tabletop in the treatment room must be replaced. It is our goal to determine the attenuation of the new, non-carbon fibre, tabletop in treatment delivery.

Materials and Methods

Measurements were performed using an ionisation chamber inserted in a slab phantom positioned at the isocenter for 6, 10 MV, 6 and 10 flattening filter free (FFF) MV photon beams. These measurements were performed with and without tabletop for 0°, 30° and 60° beam angle for a True Beam STx linac, for 5×5 cm2 and 10×10 cm2 field size beams. The attenuation was calculated for each measurement for each tabletop.

Results

At 0° incidence on the Exact IGRT Couch, the measured attenuation for 10×10 cm2 was 2·8 and 2·1% for 6 and 10 MV beams, respectively. For the same field size was measured 3·3 and 2·6% attenuation for 6 and 10 FFF MV beams, respectively. At the same incidence and regarding the other tabletops, the calculated attenuation is lower. For 10×10 cm2 field, there is 2·0, 1·4, 2·1 and 2·6% attenuation for 6, 10 MV, 6 and 10 FFF MV energy beams on the kVueTM Universal Couch. For the KvueTM Calypso® Couch 10×10 cm2 irradiation field, the measurements were 1·6, 1·3, 1·9 and 1·5%, respectively. This tendency is observed for all gantry angles.

Discussion

The attenuation outputs were definitely higher for the Varian Exact IGRT Couch when compared with the kVue tabletops. The attenuation measurements for the kVue tabletops were closer to each other. Nevertheless kVueTM Calypso® Varian tabletop showed smaller mean attenuation of the beams than kVueTM Universal Tip Insert for all measurements.

Conclusions

There was no loss in treatment quality administration due to beam attenuation in the tabletop when tabletops were exchanged because of Calypso system integration. There is no need to change between kVue tabletops whenever there is a regular treatment or a Calypso System guided treatment.

Modeling of couch transmission in the RayStation treatment planning system

PURPOSE

To present our methods and results regarding the modeling of a carbon fiber couch (Varian Exact IGRT) in the RayStation treatment planning system (TPS).

METHODS

Three geometrical-models (GMs) were implemented in the TPS to represent the three different regions of the couch (thick, medium and thin). The materials and densities of each GM component were tuned to maximize the agreement between measured and calculated attenuations. Moreover, a couch computed-tomography (CT) scan was acquired and dosimetrically compared with the GMs. For validation, plan-specific quality assurance (QA) of VMAT plans (TG-119 cases, 5 prostate and 5 H&N clinical cases) was performed by comparing measured dose distributions with doses computed with and without including the GMs in the TPS.

RESULTS

Couch attenuations up to 4.3% were measured (energy: 6MV). Compared to couch CT, GMs could be modified to optimize the agreement with measurements and reduce dependence on the dose grid resolution. For both couch CT and GM, absolute deviations between measured and calculated attenuations were within 1.0%. When including the GMs in plan-specific QA, global 2%/2mm γ-pass rates showed an average improvement of 4.8% (p-value<0.001, max +18.6%). The couch reduced the mean dose to targets by up to 2.4% of the prescribed dose for prostate cases and up to 1.4% for H&N cases.

CONCLUSIONS

RayStation accurately considers the implemented couch GMs replicating measured attenuations within an uncertainty of 1.0%. Materials and densities are proposed for the Varian Exact IGRT couch. The results obtained justify introducing couch GMs in clinical routine.

Generation and verification of QFix kVue Calypso-compatible couch top model for a dedicated stereotactic linear accelerator with FFF beams

This study details the generation, verification, and implementation of a treatment planning system (TPS) couch top model for patient support system used in conjunction with a dedicated stereotactic linear accelerator. Couch top model was created within the TPS using CT simulation images of the kVue Calpyso-compatible couchtop (with rails). Verification measurements were compared to TPS dose prediction for different energies (6 MV FFF and 10 MV FFF) and rail configurations (rails in and rails out) using: 1) central axis point-dose measurements with pinpoint chamber in water-equivalent phantom at 42 gantry angles for various field sizes (2 × 2 cm², 4 × 4 cm², 10 × 10 cm²); and 2) Gafchromic EBT3 film parallel to beam in acrylic slab to assess changes in surface and percent depth doses in PA geometry. To assess sensitivity of delivered dose to variations in patient lateral position, measurements at central axis using the pinpoint chamber geometry were taken at lateral couch displacements of 2, 5, and 10 mm for 6 MV FFF. The maximum percent difference for point-dose measurements was 3.24% (6 MV FFF) and 2.30% (10 MV FFF). The average percent difference for point-dose measurements was less than 1.10% for all beam energies and rail geometries. The maximum percent difference between calculated and measured dose can be as large as 13.0% if no couch model is used for dose calculation. The presence of the couch structures also impacts surface dose and PDD, which was evaluated with Gafchromic film measurements. The upstream shift in the depth of dose maximum (dmax) was found to be 10.5 mm for 6 MV FFF and 5.5 mm for 10 MV FFF for 'Rails In' configuration. Transmission of the treatment beam through the couch results in an increase in surface dose (absolute percentage) of approximately 50% for both photon energies (6 MV FFF and 10MV FFF). The largest sensitivity to lateral shifts occurred at the lateral boundary of the rail structures. The mean magnitude (standard deviation) of the deviation between shifted and centered measurements over all field sizes tested was 0.61% (0.61%) for 2 mm shifts, 0.46% (0.67%) for 5 mm shifts, and 0.86% (1.46%) for 10 mm shifts.

Calypso’s array attenuation

Introduction

The Calypso 4D Localization System gives the possibility to track the tumour during treatment, with no additional ionising radiation delivered. To monitor the patient continuously an array is positioned above the patient during the treatment. We intend to study, for various gantry angles, the attenuation effect of the array for 6- and 10 MV and flattening filter free (FFF) 6- and FFF 10 MV photon beams.

Materials and methods

Measurements were performed using an ion chamber placed in a slab phantom positioned at the linac isocenter for 6 MV, 10 MV, FFF 6 MV and FFF 10 MV photon beams. Measurements were performed with and without array above the phantom for 0°, 10°, 20°, 40° and 50° beam angle for a True Beam STx linac, for 5×5 and 10×10 and 15×15 cm2 field size beams to evaluate the attenuation of the array. A VMAT treatment plan was measured using an ArcCheck with and without the array in the beam path.

Results and discussion

Attenuation measured values were up to 3%. Attenuation values were between 1 and 2% with the exception of the 30°–50° gantry angles which were up to 3.3%. The ratio values calculated in the ArcCheck for relative dose and absolute dose 10 were both 1·00.

Conclusion

Attenuation of the treatment beam by the Calypso array is within acceptable limits.

Depth dose comparison of measured and calculated dose for the Eclipse virtual carbon couch top models with air gap variation

This study assessed the accuracy of Eclipse™ (Varian Medical Systems, Palo Alto, CA, USA) treatment planning system (TPS) dose calculations when using virtual couch top models to account for couch presence in patient treatments. The Flat panel and Unipanel couch tops for the Varian Exact Couch were used in this study. Assigned Hounsfield unit (HU) for the virtual couch tops were varied and TPS calculated dose was compared to measured data to determine an optimal assigned HU. Air gaps of up to 10 cm were introduced between couch and phantom to assess the ability of the models to replicate dose in this situation, commonly seen clinically. Dose was measured at a range of depths, for each air gap thickness, in order to assess the model both near surface and at various depths beyond the dose maximum. Optimal HU was taken to be that which had the best agreement between measured and calculated dose over the range of gaps and depths tested. For the Flat panel couch top this was found to be -500 HU and for the Unipanel couch top, -200 HU. Default HU parameters originally set in the models was found to be not optimal for the whole range of depths studied. With optimal HU parameters set, there was good agreement between calculated and measured dose for depths greater than 0.5 cm, but discrepancies were still observed near surface. When implementing virtual couch top models, users could improve dose calculation accuracy by determining the optimal HU from comparisons over several clinical depths rather than a single depth.

[Dose impact of a carbon fiber couch for stereotactic body radiation therapy of lung tumors]

The aim of this study was to measure the dose attenuation caused by a carbon fiber radiation therapy table (Imaging Couch Top; ICT, BrainLab) and to evaluate the dosimetric impact of ICT during stereotactic body radiation therapy (SBRT) in lung tumors. The dose attenuation of ICT was measured using an ionization chamber and modeled by means of a treatment planning system (TPS). SBRT was planned with and without ICT in a lung tumor phantom and ten cases of clinical lung tumors. The results were analyzed from isocenter doses and a dose-volume histogram (DVH): D95, Dmean, V20, V5, homogeneity index (HI), and conformity index (CI). The dose attenuation of the ICT modeled with TPS agreed to within ±1% of the actually measured values. The isocenter doses, D95 and Dmean with and without ICT showed differences of 4.1-5% for posterior single field and three fields in the phantom study, and differences of 0.6-2.4% for five fields and rotation in the phantom study and six fields in ten clinical cases. The dose impact of ICT was not significant for five or more fields in SBRT. It is thus possible to reduce the dose effect of ICT by modifying the beam angle and beam weight in the treatment plan.

Inverse planned constant dose rate volumetric modulated arc therapy (VMAT) as an efficient alternative to five-field intensity modulated radiation therapy (IMRT) for prostate

Purpose

The aim of this work was to determine if volumetric modulated arc therapy (VMAT) plans, created for constant dose-rate (cdrVMAT) delivery are a viable alternative to step and shoot five-field intensity modulated radiation therapy (IMRT).

Materials and methods

The cdrVMAT plans, inverse planned on a treatment planning system with no solution to account for couch top or rails, were created for delivery on a linear accelerator with no variable dose rate control system. A series of five-field IMRT and cdrVMAT plans were created using dual partial arcs (gantry rotating between 260° and 100°) with 4° control points for ten prostate patients with the average rectal constraint incrementally increased. Pareto fronts were compared for the planning target volume homogeneity and average rectal dose between the two techniques for each patient. Also investigated were tumour control probability and normal tissue complication probability values for each technique. The delivery parameters [monitor units (MU) and time] and delivery accuracy of the IMRT and VMAT plans were also compared.

Results

Pareto fronts showed that the dual partial arc plans were superior to the five-field IMRT plans, particularly for the clinically acceptable plans where average rectal doses were less for rotational plans (p = 0·009) with no statistical difference in target homogeneity. The cdrVMAT plans had significantly more MU (p = 0·005) but the average delivery time was significantly less than the IMRT plans by 42%. All clinically acceptable cdrVMAT plans were accurate in their delivery (gamma 99·2 ± 1·1%, 3%3 mm criteria).

Conclusions

Accurate delivery of dual partial arc cdrVMAT avoiding the couch top and rails has been demonstrated.

A validation of carbon fiber imaging couch top modeling in two radiation therapy treatment planning systems: Philips Pinnacle3 and BrainLAB iPlan RT Dose

BACKGROUND

Carbon fiber (CF) is now the material of choice for radiation therapy couch tops. Initial designs included side metal bars for rigidity; however, with the advent of IGRT, involving on board imaging, new thicker CF couch tops without metal bars have been developed. The new design allows for excellent imaging at the expense of potentially unacceptable dose attenuation and perturbation.

OBJECTIVES

We set out to model the BrainLAB imaging couch top (ICT) in Philips Pinnacle(3) treatment planning system (TPS), to validate the already modeled ICT in BrainLAB iPlan RT Dose treatment planning system and to compute the magnitude of the loss in skin sparing.

RESULTS

Using CF density of 0.55 g/cm(3) and foam density of 0.03 g/cm(3), we demonstrated an excellent agreement between measured dose and Pinnacle(3) TPS computed dose using 6 MV beam. The agreement was within 1% for all gantry angle measured except for 120°, which was 1.8%. The measured and iPlan RT Dose TPS computed dose agreed to within 1% for all gantry angles and field sizes measured except for 100° where the agreement was 1.4% for 10 cm × 10 cm field size. Predicted attenuation through the couch by iPlan RT Dose TPS (3.4% - 9.5%) and Pinnacle(3) TPS (2% - 6.6%) were within the same magnitude and similar to previously reported in the literature. Pinnacle(3) TPS estimated an 8% to 20% increase in skin dose with increase in field size. With the introduction of the CF couch top, it estimated an increase in skin dose by approximately 46 - 90%. The clinical impact of omitting the couch in treatment planning will be dependent on the beam arrangement, the percentage of the beams intersecting the couch and their angles of incidence.

CONCLUSION

We have successfully modeled the ICT in Pinnacle(3) TPS and validated the modeled ICT in iPlan RT Dose. It is recommended that the ICT be included in treatment planning for all treatments that involve posteriors beams. There is a significant increase in skin dose that is dependent on the percentage of the beam passing through the couch and the angle of incidence.