Bioflocculation of pollutants in wastewater using flocculant derived from Providencia huaxiensis OR794369.1

BACKGROUND

Water pollution has become a major environmental and health concern due to increasing population and industrialisation. Microbial flocculants are promising agents for treatment of contaminated water owing to their effectiveness, eco-friendliness, and high biosafety levels. In this study, culture conditions of Providencia huaxiensis OR794369.1 were optimised and its bioflocculant was extracted, characterised and used to treat wastewater.

RESULTS

The maximum flocculating activity of 92% and yield of 3.5 g/L were obtained when cultivation conditions were: 3% inoculum size, starch, casein, initial pH of 6, cultivation temperature of 30 oC and 72 h of fermentation. The bioflocculant is an amorphous glycoprotein biomolecule with 37.5% carbohydrates, 27.9% protein, and 34.6% uronic acids. It is composed of hydroxyl, amino, alkanes, carboxylic acid and amines groups as its main functional structures. It was found to be safe to use as it demonstrated non-cytotoxic effects on bovine dermis and African green monkey kidney cells, illustrating median inhibitory concentration (IC50) values of 180 and > 500 µg/mL on both cell lines, respectively. It demonstrated the removal efficiencies of 90% on chemical oxygen demand (COD), 97% on biological oxygen demand (BOD) and 72% on Sulphur on coal mine wastewater. It also revealed the reduction efficacies of 98% (COD) and 92% (BOD) and 70% on Sulphur on domestic wastewater.

CONCLUSION

The bioflocculant was effective in reducing pollutants and thus, illustrated potential to be used in wastewater treatment process as an alternative.

A Quarter Century of Marine Biodiscovery in Algoa Bay, South Africa

Algoa Bay, the largest crenulate bay on the southeastern coast of South Africa, is currently one of the most well-studied marine ecosystems in southern Africa. A plethora of endemic marine invertebrates inhabits the benthic reefs on the western edge of the Bay in close proximity to South Africa's sixth largest city. Over the past 25 years, South African marine natural products chemists, together with international collaborators from the US National Cancer Institute and other US institutions, have focused their attention on Algoa Bay's benthic marine invertebrates as a potential source of new anticancer compounds. This review commemorates a quarter of a century of marine biodiscovery in Algoa Bay and presents the structures and bioactivities of 49 new and 36 known specialized metabolites isolated from two molluscs, eight ascidians, and six sponges. Thirty-nine of these compounds were cytotoxic to cancer cells in vitro with 20 exhibiting moderate to potent cytotoxicity. Six other compounds exhibited antimicrobial activity. Foremost among the potential anticancer compounds is mandelalide A (38) from the Algoa Bay ascidian Lissoclinum species.

Isolation of a Marine Bacterium and Application of Its Bioflocculant in Wastewater Treatment

Bioflocculation has become the method of choice in wastewater treatment because of its effectiveness, environmental friendliness and innocuousness to humans. In this study, the bioflocculant-producing bacterium was isolated and its bioflocculant was used in wastewater treatment. The isolate was identified by 16S rRNA gene sequencing analysis. Its culture conditions (inoculum size, carbon and nitrogen sources, pH, temperature and time) were optimised using the one-factor-at-a-time assay. The cytotoxicity of the bioflocculant was assessed on human colorectal adenocarcinoma cells (Caco2) by tetrazolium-based colorimetric method. The ability of the bioflocculant to reduce biochemical oxygen demand (BOD) and chemical oxygen demand (COD) in wastewater was evaluated using Jar test. The bacterium was identified as Bacillus subtilis CSM5 and the maximum flocculating activity of 92% was observed when fructose and urea were used as nutrients and the culture conditions were adjusted to 30 °C, pH 9, 160 rpm and 72 h of incubation. Caco2 exhibited 90% viability when the highest bioflocculant concentration of 200 µg/µL was used. The reduction of BOD and COD was achieved at 59 ± 3.1 and 75 ± 0.4%, respectively. In conclusion, B. subtilis CSM5 is a good candidate for bioflocculant production and its bioflocculant has good potential for use in wastewater treatment.

Isolation and Optimisation of Culture Conditions for a Marine Bioflocculant-Producing Bacterium and Application of Its Bioflocculant in Wastewater Treatment

The application of bioflocculants has become an alternative to that of chemical flocculants in wastewater treatment due to their environmental friendliness and non-toxic effects. This study aimed at isolating a bioflocculant-producing bacterium from marine water, optimisation of its culture conditions, and investigation of the removal efficiency of its bioflocculant on pollutants in wastewater. The bacterium was identified by 16S rRNA gene analysis. Optimal carbon and nitrogen sources, inoculum size, temperature, pH, and time were determined by the one-factor-at-a-time assay. The cytotoxicity of the bioflocculant was assessed on African green monkey kidney and bovine dermis cells using a tetrazolium-based columetric (MTT) method. Its removal efficiencies on chemical oxygen demand (COD), biological oxygen demand (BOD) and sulphur were determined using the Jar test method. The bacterial isolate was identified as Ochrobactrum oryzae AB84113. A maximum flocculating activity of 92% and a yield of 3.768 g/L were obtained when a 1% (v/v) inoculum size was used in the presence of starch and yeast extract at pH 7, 30 °C, and after 72 h of cultivation. The bioflocculant demonstrated non-cytotoxic effects on bovine dermis and African green monkey kidney cells. The bioflocculant removed 98% COD, 91% BOD and 86% of Sulphur. The bioflocculant has potential for pollutant removal from industrial wastewater.

Optimal production of bioflocculant from Pseudomonas sp. GO2 and its removal characteristics of heavy metals

Bioflocculant may be a promising bioactivator for heavy metal removal duo to its eco-friendly properties and remarkable ability to adsorb heavy metals. In this study, bioflocculant production from a bacterium, Pseudomonas sp. GO2, was optimized and its removal efficiency for two heavy metal ions was evaluated. Results demonstrated that the maximal flocculation efficiency was achieved with concentration levels of 5 g/L glucose, 3 g/L casein, and 5 g/L NaCl, with an initial pH of 9.0, and a fermentation time of 48 h. Bioflocculant produced by GO2 had a stronger removal efficiency for Cd²⁺ than that of Pb²⁺, with highest removal efficiencies of 85.38% and 80.87%, respectively. The adsorption process was mainly dependent on the monolayer and chemisorption based on the adsorption isotherm and kinetic models. This study demonstrated that bioflocculant produced by the GO2 strain has the potential to be used in heavy metal treatment from industrial wastewater.

Isolation and Optimization of Culture Conditions of a Bioflocculant-Producing Fungi from Kombucha Tea SCOBY

Biolocculants are gaining attention in research due to their environmental friendliness and innocuousness to human in comparison to the conventional flocculants. The present study aimed to investigate the ability of fungi from Kombucha tea SCOBY to produce effective bioflocculant in bulk. A 16S rRNA gene sequence analysis was utilized to identify the isolate. The medium composition (carbon and nitrogen sources) and culture conditions (inoculum size, temperature, shaking speed, pH, and time) were optimized using one-factor-at-a-time method. The functional groups, morphology, and crystallinity of the bioflocculant were evaluated using Fourier transform infrared (FT-IR), scan electron microscope (SEM) and X-ray diffractometry (XRD). The fungus was found to be Pichia kudriavzevii MH545928.1. It produced a bioflocculant with flocculating activity of 99.1% under optimum conditions; 1% (v/v) inoculum size, glucose and peptone as nutrient sources, 35 °C, pH 7 and the shaking speed of 140 rpm for 60 h. A cumulus-like structure was revealed by SEM; FT-IR displayed the presence of hydroxyl, carboxyl, amine, and thiocynates. The XRD analysis demonstrated the bioflocculant to have big particles with diffraction peaks at 10° and 40° indicating its crystallinity. Based on the obtained results, P. kudriavzevii MH545928.1 has potential industrial applicability as a bioflocculant producer.

Removal of Pollutants in Mine Wastewater by a Non-Cytotoxic Polymeric Bioflocculant from Alcaligenes faecalis HCB2

Bioflocculation is a physicochemical technique often employed to efficiently remove colloidal water pollutants. Consequently, in this study, a bioflocculant was produced, characterised and applied to remove pollutants in mine wastewater. The maximum flocculation activity of 92% was recorded at 30 °C, pH 9.0 when maltose and urea were used as energy sources and 72 h of fermentation at the inoculum size of 1% (v/v). K⁺ proved to be a favourable cation. The bioflocculant yield of 4 g/L was obtained. Scanning electron microscopy illustrated a hexagonal-like structure of the bioflocculant. It is composed of carbohydrates and proteins in mass proportion of 88.6 and 9.5%, respectively. The Fourier transform infrared spectrum revealed the presence of hydroxyl, amide and amino functional groups. More than 73% of the bioflocculant was obtained after exposure to 600 °C using the thermogravimetric analyser. Human embryonic kidney 293 (HEK 293) cells exhibited 95% viability after being treated with 200 µg/µL of the bioflocculant. The flocculation mechanisms were proposed to be as a result of a double layer compression by K⁺, chemical reactions and bridging mechanism. The removal efficiencies of 59, 72, and 75% on biological oxygen demand, chemical oxygen demand and sulphur, were obtained respectively. Thus, the bioflocculant have potential use in wastewater treatment.

Flocculation behaviour of bioflocculant produced from chicken viscera

The flocculation performance of bioflocculant produced by Aspergillus flavus S44-1 grown on chicken viscera hydrolysate was investigated. The investigations were carried out using jar testing and kaolin clay suspension as model wastewater. The bioflocculant yielded a minimum of 83.1% efficiency in flocculating 2-12 g L-1 kaolin clay suspension over a wide temperature range (4-80 °C) and functioned maximally at neutral pH. The bioflocculant significantly flocculated different suspended particles such as activated carbon (92%), soil solid (94.8%), and algae (69.4%) at varying concentrations. Bridging mediated by cation is suggested as the main mechanism of flocculation by the present bioflocculant.

Production and Characterization of a Bioflocculant Produced by Bacillus salmalaya 139SI-7 and Its Applications in Wastewater Treatment

The production, optimization, and characterization of the bioflocculant QZ-7 synthesized by a novel Bacillus salmalaya strain 139SI isolated from a private farm soil in Selangor, Malaysia, are reported. The flocculating activity of bioflocculant QZ-7 present in the selected strain was found to be 83.3%. The optimal culture for flocculant production was achieved after cultivation at 35.5 °C for 72 h at pH 7 ± 0.2, with an inoculum size of 5% (v/v) and sucrose and yeast extract as carbon and nitrogen sources. The maximum flocculating activity was found to be 92.6%. Chemical analysis revealed that the pure bioflocculant consisted of 79.08% carbohydrates and 15.4% proteins. The average molecular weight of the bioflocculant was calculated to be 5.13 × 10⁵ Da. Infrared spectrometric analysis showed the presence of carboxyl (COO-), hydroxyl (-OH), and amino (-NH₂) groups, polysaccharides and proteins. The bioflocculant QZ-7 exhibited a wide pH stability range from 4 to 7, with a flocculation activity of 85% at pH 7 ± 0.2. In addition, QZ-7 was thermally stable and retained more than 80% of its flocculating activity after being heated at 80 °C for 30 min. SEM analysis revealed that QZ-7 exhibited a clear crystalline brick-shaped structure. After treating wastewater, the bioflocculant QZ-7 showed significant flocculation performance with a COD removal efficiency of 93%, whereas a BOD removal efficiency of 92.4% was observed in the B. salmalaya strain 139SI. These values indicate the promising applications of the bioflocculant QZ-7 in wastewater treatment.

A novel thermally stable heteropolysaccharide-based bioflocculant from hydrocarbonoclastic strain Kocuria rosea BU22S and its application in dye removal

A new bioflocculant named pKr produced by hydrocarbonoclastic strain Kocuria rosea BU22S (KC152976) was investigated. Gas chromatography-flame ionization detector (GC-FID) analysis confirmed the high potential of the strain BU22S in the degradation of n-alkanes. Plackett-Burman experimental design and response surface methodology were carried out to optimize pKr production. Glucose, peptone and incubation time were found to be the most significant factors affecting bioflocculant production. Maximum pKr production was about 4.72 ± 0.02 g/L achieved with 15.61 g/L glucose, 6.45 g/L peptone and 3 days incubation time. Chemical analysis of pKr indicated that it contained 71.62% polysaccharides, 16.36% uronic acid and 2.83% proteins. Thin layer chromatography analysis showed that polysaccharides fraction consisted of galactose and xylose. Fourier transform infrared analysis revealed the presence of many functional groups, hydroxyl, carboxyl, methoxyl, acetyl and amide that likely contribute to flocculation. K. rosea pKr showed high flocculant potential using kaolin clay at different pH (2-11), temperature (0-100°C) and cation concentrations. The bioflocculant was particularly effective in flocculating soluble anionic dyes, Reactive Blue 4 and Acid Yellow, with a decolorization efficiency of 76.4% and 72.6%, respectively. The outstanding flocculating performances suggest that pKr could be useful for bioremediation applications.

Production and flocculating properties of a compound biopolymer flocculant from corn ethanol wastewater

A compound biopolymer flocculant (CBF) produced using corn ethanol wastewater as substrate was investigated. After optimization of culture conditions, 3.08 g/L of purified CBF was extracted from the culture broth following 48 h of cultivation. The CBF macromolecule is mainly composed of protein (15.9%) and polysaccharide (81.8%). The polysaccharide component includes neutral sugars (28.92%), amino sugars (4.04%) and uronic acid (11.69%), with the neutral sugars being glucose, mannose, and lactose at a molar ratio of 4.1:1.5:1.9. CBF is pH tolerant from 3.0 to 12.0 and thermal tolerant from 20 to 100 °C, allowing for its application over a wide range of conditions. Furthermore, the Langmuir model better describes CBF adsorption on kaolin clay, as compared to the Freundlich model. Charge neutralization and bridging mechanisms are the primary flocculation mechanisms. In addition, CBF shows a high methylene blue removal efficiency. These results indicate that this compound biopolymer flocculant has great potential in dye wastewater treatment.

Implications for public health demands alternatives to inorganic and synthetic flocculants: bioflocculants as important candidates

Chemical flocculants are generally used in drinking water and wastewater treatment due to their efficacy and cost effectiveness. However, the question of their toxicity to human health and environmental pollution has been a major concern. In this article, we review the application of some chemical flocculants utilized in water treatment, and bioflocculants as a potential alternative to these chemical flocculants. To the best of our knowledge, there is no report in the literature that provides an up‐to‐date review of the relevant literature on both chemical flocculants and bioflocculants in one paper. As a result, this review paper comprehensively discussed the various chemical flocculants used in water treatment, including their advantages and disadvantages. It also gave insights into bioflocculants production, challenges, various factors influencing their flocculating efficiency and their industrial applications, as well as future research directions including improvement of bioflocculants yields and flocculating activity, and production of cation‐independent bioflocculants. The molecular biology and synthesis of bioflocculants are also discussed.

Evaluation of flocculating performance of a thermostable bioflocculant produced by marine Bacillus sp

This study assessed the bioflocculant (named MBF-W7) production potential of a bacterial isolate obtained from Algoa Bay, Eastern Cape Province of South Africa. The 16S ribosomal deoxyribonucleic acids gene sequence analysis showed 98% sequence similarity to Bacillus licheniformis strain W7. Optimum culture conditions for MBF-W7 production include 5% (v/v) inoculum size, maltose and NH4NO3 as carbon and nitrogen sources of choice, medium pH of 6 as the initial pH of the growth medium. Under these optimal conditions, maximum flocculating activity of 94.9% was attained after 72 h of cultivation. Chemical composition analyses showed that the purified MBF-W7 was a glycoprotein which was predominantly composed of polysaccharides 73.7% (w/w) and protein 6.2% (w/w). Fourier transform infrared spectroscopy revealed the presence of hydroxyl, carboxyl and amino groups as the main functional groups identified in the bioflocculant molecules. Thermogravimetric analyses showed the thermal decomposition profile of MBF-W7. Scanning electron microscopy imaging revealed that bridging played an important role in flocculation. MBF-W7 exhibited excellent flocculating activity for kaolin clay suspension at 0.2 mg/ml over a wide pH range of 3-11; with the maximal flocculation rate of 85.8% observed at pH 3 in the presence of Mn(2+). It maintained and retained high flocculating activity of over 70% after heating at 100°C for 60 min. MBF-W7 showed good turbidity removal potential (86.9%) and chemical oxygen demand reduction efficiency (75.3%) in Tyume River. The high flocculating rate of MBF-W7 makes it an attractive candidate to replace chemical flocculants utilized in water treatment.

Revealing the characteristics of a novel bioflocculant and its flocculation performance in Microcystis aeruginosa removal

In the present work, a novel bioflocculant, EPS-1, was prepared and used to flocculate the kaolin suspension and Microcystis aeruginosa. We focused on the characteristics and flocculation performance of EPS-1, especially with regard to its protein components. An important attribute of EPS-1 was its protein content, with 18 protein types identified that occupied a total content of 31.70% in the EPS-1. Moreover, the flocculating activity of these protein components was estimated to be no less than 33.93%. Additionally, polysaccharides that occupied 57.12% of the total EPS-1 content consisted of four monosaccharides: maltose, D-xylose, mannose, and D-fructose. In addition, carbonyl, amino, and hydroxyl groups were identified as the main functional groups. Three main elements, namely C1s, N1s, and O1s, were present in EPS-1 with relative atomic percentages of 62.63%, 24.91%, and 10.5%, respectively. Zeta potential analysis indicated that charge neutralization contributed to kaolin flocculation, but was not involved in M. aeruginosa flocculation. The flocculation conditions of EPS-1 were optimized, and the maximum flocculating efficiencies were 93.34% within 2 min for kaolin suspension and 87.98% within 10 min for M. aeruginosa. These results suggest that EPS-1 could be an alternative to chemical flocculants for treating wastewaters and cyanobacterium-polluted freshwater.

Characterization of a Bioflocculant (MBF-UFH) Produced by Bacillus sp. AEMREG7

A bioflocculant named MBF-UFH produced by a Bacillus species isolated from sediment samples of Algoa Bay of the Eastern Cape Province of South Africa was characterized. The bacterial identification was through 16S rDNA sequencing; nucleotide sequences were deposited in GenBank as Bacillus sp. AEMREG7 with Accession Number KP659187. The production of the bioflocculant was observed to be closely associated with cell growth. The bioflocculant had the highest flocculating activity of 83.2% after 72 h of cultivation, and approximately 1.6 g of purified MBF-UFH was recovered from 1 L of fermentation broth. Its chemical analyses indicated that it is a glycoprotein composed of polysaccharide (76%) and protein (14%). Fourier transform infrared spectroscopy (FTIR) revealed that it consisted of hydroxyl, amide, carboxyl and methoxyl as the functional moieties. Scanning electron microscopy (SEM) revealed the amorphous structure of MBF-UFH and flocculated kaolin clay particles. The maximum flocculating activity of 92.6% against kaolin clay suspension was achieved at 0.3 mg/mL over pH ranges of 3-11 with the peak flocculating rate at pH 8 in the presence of MgCl2. The bioflocculant retained high flocculating activity of 90% after heating at 100 °C for 1 h. MBF-UFH appears to have immense potential as an alternative to conventional chemical flocculants.

Bacillus toyonensis strain AEMREG6, a bacterium isolated from South African marine environment sediment samples produces a glycoprotein bioflocculant

A bioflocculant-producing bacteria, isolated from sediment samples of a marine environment in the Eastern Cape Province of South Africa demonstrated a flocculating activity above 60% for kaolin clay suspension. Analysis of the 16S ribosomal deoxyribonucleic acid (rDNA) nucleotide sequence of the isolate in the GenBank database showed 99% similarity to Bacillus toyonensis strain BCT-7112 and it was deposited in the GenBank as Bacillus toyonensis strain AEMREG6 with accession number KP406731. The bacteria produced a bioflocculant (REG-6) optimally in the presence of glucose and NH4NO3 as the sole carbon and nitrogen source, respectively, initial medium pH of 5 and Ca2+ as the cation of choice. Chemical analysis showed that purified REG-6 was a glycoprotein mainly composed of polysaccharide (77.8%) and protein (11.5%). It was thermally stable and had strong flocculating activity against kaolin suspension over a wide range of pH values (3-11) with a relatively low dosage requirement of 0.1 mg/mL in the presence of Mn2+. Fourier transform infrared spectroscopy (FTIR) revealed the presence of hydroxyl, carboxyl and amide groups preferred for flocculation. Scanning electron microscopy (SEM) revealed that bridging was the main flocculation mechanism of REG-6. The outstanding flocculating performance of REG-6 holds great potential to replace the hazardous chemical flocculants currently used in water treatment.