A novel aptasensor platform for the detection of carcinoembryonic antigen using quartz crystal microbalance

In this study, a quartz crystal microbalance (QCM) aptasensor for carcinoembryonic antigen (CEA), a well-known biomarker for various cancer types, was reported, utilizing two different aptamers. To achieve this, a nanofilm of 4-mercaptophenyl was electrochemically attached to gold-coated QCM crystal surfaces via the reduction of 4-mercaptobenzenediazonium salt (4 MB-DAT) using cyclic voltammetry. Subsequently, gold nanoparticles (AuNP) were affixed to this structure, and then aptamers (antiCEA1 and antiCEA2) modified with SH-functional ends bound to AuNPs completed the modification. The analytical performance of the CEA sensor was evaluated through simultaneous QCM measurements employing CEA solutions ranging from 0.1 ng/mL to 25 ng/mL. The detection limit (LOD) for CEA was determined to be 102 pg/mL for antiCEA1 and 108 pg/mL for antiCEA2 aptamers. Interday and intraday precision and accuracy tests yielded maximum results of 4.3 and + 3.8, respectively, for both aptasensors, as measured by relative standard deviation (RSD%) and relative error (RE%). The kinetic data of the aptasensors resulted in affinity values (KD) of 0.43 ± 0.14 nM for antiCEA1 and 0.75 ± 0.42 nM for antiCEA2. These values were lower than the reported values of 3.9 nM and 37.8 nM for both aptamers, respectively. The selectivity of the aptasensor was evaluated by measuring the signal changes caused by alpha-fetoprotein (AFP), cancer antigen (CA-125), and vascular endothelial growth factor (VEGF-165) individually and together at a concentration of 500 ng/mL, resulting in a maximum 4.1 % change, which was comparable to precision and accuracy values reported in the literature. After confirming the selectivity of the aptamers, recovery experiments were conducted using spiked commercial serum samples to simulate real samples, and the lowest recovery value obtained was 95.4 %. It was determined that two different aptasensors could be successfully used for the QCM-based detection of CEA in this study.

Excellent fluorescence detection of Cu2+in water system using N-acetyl-L-cysteines modified CdS quantum dots as fluorescence probe

View of the negative influence of metal ions on natural environment and human health, fast and quantitative detection of metals ions in water systems is significant. Ultra-small grain size CdS quantum dots (QDs) modified with N-acetyl-L-cysteines (NALC) (NALC-CdS QDs) are successfully prepared via a facile hydrothermal route. Based on the changes of fluorescence intensity of NALC-CdS QDs solution after adding metal ions, the fluorescence probe made from the NALC-CdS QDs is developed to detect metal ions in water systems. Among various metal ions, the fluorescence of NALC-CdS QDs effectively quenched by the addition of Cu²⁺, the probe shows high sensitivity and selectivity for detecting Cu²⁺in other interferential metal ions coexisted system. Importantly, the fluorescence intensity of NALC-CdS QDs changes upon the concentration of Cu²⁺, the probe displays an excellent linear relationship between the fluorescence quenching rate and the concentration of Cu²⁺in ranging from 1 to 25μM. Besides, the detected limitation of the probe towards Cu²⁺as low as 0.48μM. The measurement of Cu²⁺in real water sample is also carried out using the probe. The results indicate that NALC-CdS QDs fluorescence probe may be a promising candidate for quantitative Cu²⁺detection in practical application.

Boron- and nitrogen-doped photoluminescent polymer carbon nanoparticles as nanosensors for imaging detection of Cu2+ and biothiols in living cells

Boron and nitrogen co-doped ellipsoidal polymer carbon nanoparticles-based nanoprobe for fluorescence detection and imaging of biothiols in biological samples.