Design modifications and evaluation of the silicone artificial finger joints

BACKGROUND

There are many reasons that could lead to finger joint arthroplasty, and the most familiar reason is osteoarthritis. Silicone finger joint are the most commonly used implants. However, these implants might fracture with time and cause wear which will lead to chronic inflammation and synovitis for the patient and then implant failure.

OBJECTIVE

The aim of this study is to improve the design of the silicone finger joint and simulate the different designs using finite element analysis (FEA) simulation.

METHOD

Three different designs were drawn and FEA has been used in this study using Solidworks software. The first design is the silicone finger joint design without any modification, the second one is modified design with added ribs to the junction of distal stem and hinge and the third design was added filler material inside the body of the artificial joint. An axial force with 625 N that was applied on the upper part of the distal stem which is nearly represents the maximum value of the grip strength for normal males.

RESULTS

The results showed improvement on the design in which the concentrated stress at the junction of the distal stem and hinge of the design was distributed. In addition, the Von Mises stress was stable for the modified design with added ribs and the added filler material designs after 15°.

CONCLUSION

The design modification could improve the stress distribution and stability of the artificial finger joint and increase the lifetime expectancy of these implants.

Range of motion of the metacarpophalangeal joint in rheumatoid patients, with and without a flexible joint replacement prosthesis, compared with normal subjects

BACKGROUND

The metacarpophalangeal is commonly affected by rheumatoid arthritis. This may lead to joint replacement with a flexible prosthesis. The aims of this study were to determine the effects of rheumatoid arthritis on joint motion and to determine whether joint replacement needs to restore the full range of motion.

METHODS

Three-dimensional motion analysis was used to measure the range of motion of the metacarpophalangeal joint in rheumatoid patients with and without a flexible silicone arthroplasty, when performing pinch and key grips, when making a fist and when spreading the fingers. The results were compared with those from younger and older normal subjects.

FINDINGS

There appeared to be a trend for a decrease in range of motion from younger normal to older normal to rheumatoid (no prosthesis) to rheumatoid (with prosthesis) subject groups. However, statistically different (p<0.05) results were only observed for some movements (mostly involved in making a fist), in some fingers and between some subject groups. The only exception to this apparent trend was in flexion/extension when spreading the fingers into abduction.

INTERPRETATION

Making a fist is the most sensitive simple measure of range of motion in the metacarpophalangeal joint. Successful replacement of the metacarpophalangeal joint in patients with rheumatoid arthritis need not restore the normal range of motion.

BIOMECHANICAL PROPERTIES OF EXTENSOR TENDON REPAIR USING THE SIX-STRAND SINGLE-LOOP SUTURE TECHNIQUE: A COMPARATIVE ANALYSIS WITH THREE OTHER TECHNIQUES IN CADAVERIC MODELS

A six-strand single-loop technique has been implemented for repairing extensor tendons. This paper describes an investigation to compare the biomechanical properties of extensor tendons repaired using this technique with three other commonly used techniques, namely the Kessler-Tajima (two-stand) technique, the Tsuge (two-strand) technique, and the modified (four-strand and double-loop) Tsuge technique. Epitendinous stitches were implemented on all techniques. From human cadaveric hands, extensor tendons were harvested, transected, and repaired using these techniques. Tensile test was performed on the repaired tendons to determine the force at the first gap opening, 1-mm and 2-mm gap distances and at the maximum load. We have observed that at the first gap opening, the forces generated in the tendons repaired using the six-strand, Kessler-Tajima, and modified Tsuge techniques are significantly larger than the Tsuge technique. Thereafter, the force generated at gap distances of 1 mm, 2 mm, and the maximum force depend on the number of strands and the epitendinous stitches. In this case, the maximum force (31.80 N ± 4.73 N) from the six-strand technique is significantly higher than that from the Kessler-Tajima technique. In particular, all samples from the six-strand technique failed by suture pull-out. In contrast, suture pull-out is less common for the other techniques; these samples also exhibited suture rupture. This study is important because it reveals that cadaveric tendons repaired using the Kessler-Tajima, modified Tsuge, and six-strand techniques can accommodate higher initial forces (compared to the Tsuge technique) and, thus, are more effective for resisting gap formation. Among these techniques, it is shown that the six-strand configuration is reliable because the strands, rather than breaking, results in pull-out at sufficiently high loads. Thus, the six-strand approach for anchoring the ruptured tissue results in the transfer of large forces to the suture. It is suggested that the six-strand technique may be a viable technique since it requires only a single-loop suture and this may simplify the repair procedure and tendon handling without increasing the bulk of the repaired tendon appreciably.

Frequency dependence of viscoelastic properties of medical grade silicones

Cylinders of medical grade silicone elastomers, (29 mm in diameter and 13 mm thick), immersed in physiological saline solution at 37 degrees C, were investigated by dynamic mechanical analysis (DMA). A sinusoidal cyclic compression of 40 +/- 5 N was applied over a frequency range, f, of 0.02-100 Hz. Values of the storage, E', and loss, E'', moduli for the cylinders were found to depend on f; the dependence of E' or E'' on the logarithm (base 10) of f was represented by a third-order polynomial. Above about 0.3 Hz, the cylindrical specimens appeared to be undergoing the onset of a transition from the rubbery to the glassy state. There was no significant difference between results obtained at 37 and 23 degrees C; pretreatment of specimens in physiological saline at 37 degrees C for 24 h and 29 days had no appreciable effect on the results.