Dynamic pattern selection in polymorphic elastocapillarity

Drying of fine hair and fibers induces dramatic capillary-driven deformation, with important implications on natural phenomena and industrial processes. We recently observed peculiar self-assembly of hair bundles into various distinct patterns depending on the interplay between the bundle length and the liquid drain rate. Here, we propose a mechanism for this pattern selection, and derive and validate theoretical scaling laws for the polymorphic self-assembly of polygonal hair bundles. Experiments are performed by submerging the bundles into a liquid bath, then draining down the liquid. Depending on the interplay between the drain rates and the length of the fibers, we observe the bundles morphing into stars (having concave sides), polygons (having straight edges and rounded corners), or circles. The mechanism of self-assembly at the high drain regime is governed by two sequential stages. In the first stage of the high drain rate regime, the liquid covers the outside of the bundles, and drainage from inside the bundle does not play a role in the self-assembly due to the high viscous stress. The local pressure at the corners of the wet bundles compresses the fibers inward blunting the corners, and the internal lubrication facilitates fiber rearrangement. In the second stage, the liquid is slowly draining from within the fiber spacing, and the negative capillary pressure at the perimeter causes the fibers to tightly pack. In the slow drainage regime, the first stage is absent, and the fibers slowly aggregate without initial dynamic rearrangement. Understanding the mechanism of dynamic elastocapillarity offers insights for studying the complicated physics of wet granular drying.

Extrusion-based 3D printed magnesium scaffolds with multifunctional MgF2 and MgF2-CaP coatings

Additively manufactured (AM) biodegradable magnesium (Mg) scaffolds with precisely controlled and fully interconnected porous structures offer unprecedented potential as temporary bone substitutes and for bone regeneration in critical-sized bone defects. However, current attempts to apply AM techniques, mainly powder bed fusion AM, for the preparation of Mg scaffolds, have encountered some crucial difficulties related to safety in AM operations and severe oxidation during AM processes. To avoid these difficulties, extrusion-based 3D printing has been recently developed to prepare porous Mg scaffolds with highly interconnected structures. However, limited bioactivity and a too high rate of biodegradation remain the major challenges that need to be addressed. Here, we present a new generation of extrusion-based 3D printed porous Mg scaffolds that are coated with MgF₂ and MgF₂-CaP to improve their corrosion resistance and biocompatibility, thereby bringing the AM scaffolds closer to meeting the clinical requirements for bone substitutes. The mechanical properties, in vitro biodegradation behavior, electrochemical response, and biocompatibility of the 3D printed Mg scaffolds with a macroporosity of 55% and a strut density of 92% were evaluated. Furthermore, comparisons were made between the bare scaffolds and the scaffolds with coatings. The coating not only covered the struts but also infiltrated the struts through micropores, resulting in decreases in both macro- and micro-porosity. The bare Mg scaffolds exhibited poor corrosion resistance due to the highly interconnected porous structure, while the MgF₂-CaP coatings remarkably improved the corrosion resistance, lowering the biodegradation rate of the scaffolds down to 0.2 mm y^-1. The compressive mechanical properties of the bare and coated Mg scaffolds before and during in vitro immersion tests for up to 7 days were both in the range of the values reported for the trabecular bone. Moreover, direct culture of MC3T3-E1 preosteoblasts on the coated Mg scaffolds confirmed their good biocompatibility. Overall, this study clearly demonstrated the great potential of MgF₂-CaP coated porous Mg prepared by extrusion-based 3D printing for further development as a bone substitute.

The Role of Solvents in Lithography-Based Ceramic Manufacturing of Lithium Disilicate

Digital dentistry is increasingly replacing conventional methods of manually producing dental restorations. With regards to computer-aided manufacturing (CAM), milling is state of the art. Additive manufacturing (AM), as a complementary approach, has also found its way into dental practices and laboratories. Vat photo-polymerization is gaining increasing attention, because it enables the production of full ceramic restorations with high precision. One of the two predominantly used ceramic materials for these applications is lithium disilicate, Li₂Si₂O₅. This glass ceramic exhibits a substantial fracture toughness, although possesses much lower bending strength, than the other predominantly used ceramic material, zirconia. Additionally, it shows a much more natural optical appearance, due to its inherent translucency, and therefore is considered for anterior tooth restorations. In this work, an optimized formulation for photo-reactive lithium disilicate suspensions, to be processed by vat photo-polymerization, is presented. Following the fundamental theoretical considerations regarding this processing technique, a variety of solvents was used to adjust the main properties of the suspension. It is shown that this solvent approach is a useful tool to effectively optimize a suspension with regards to refractive index, rheology, and debinding behavior. Additionally, by examining the effect of the absorber, the exposure time could be reduced by a factor of ten.

Solvent-cast 3D printing of magnesium scaffolds

Biodegradable porous magnesium (Mg) scaffolds are promising for application in the regeneration of critical-sized bone defects. Although additive manufacturing (AM) carries the promise of offering unique opportunities to fabricate porous Mg scaffolds, current attempts to apply the AM approach to fabricating Mg scaffolds have encountered some crucial issues, such as those related to safety in operation and to the difficulties in composition control. In this paper, we present a room-temperature extrusion-based AM method for the fabrication of topologically ordered porous Mg scaffolds. It is composed of three steps, namely (i) preparing a Mg powder loaded ink with desired rheological properties, (ii) solvent-cast 3D printing (SC-3DP) of the ink to form scaffolds with 0 °/ 90 °/ 0 ° layers, and (iii) debinding and sintering to remove the binder in the ink and then get Mg powder particles bonded by applying a liquid-phase sintering strategy. A rheological analysis of the prepared inks with 54, 58 and 62  vol% Mg powder loading was performed to reveal their viscoelastic properties. Thermal-gravimetric analysis (TGA), Fourier transform infrared spectroscopy (FTIR), carbon/sulfur analysis and scanning electron microscopy (SEM) indicated the possibilities of debinding and sintering at one single step for fabricating pure Mg scaffolds with high fidelity and densification. The resulting scaffolds with high porosity contained hierarchical and interconnected pores. This study, for the first time, demonstrated that the SC-3DP technique presents unprecedented possibilities to fabricate Mg-based porous scaffolds that have the potential to be used as a bone-substituting material. STATEMENT OF SIGNIFICANCE: Biodegradable porous magnesium scaffolds are promising for application in the regeneration of critical-sized bone defects. Although additive manufacturing (AM) carries the promise of offering unique opportunities to fabricate porous magnesium scaffolds, current attempts to apply the AM approach to fabricating magnesium scaffolds still have some crucial limitations. This study demonstrated that the solvent-cast 3D printing technique presents unprecedented possibilities to fabricate Mg-based porous scaffolds. The judicious chosen of formulated binder system allowed for the negligible binder residue after debinding and the short-time liquid-phase sintering strategy led to a great success in sintering pure magnesium scaffolds. The resulting scaffolds with hierarchical and interconnected pores have great potential to be used as a bone-substituting material.

Effect of Polymer Binder on the Synthesis and Properties of 3D-Printable Particle-Based Liquid Materials and Resulting Structures

Recent advances have demonstrated the ability to 3D-print, via extrusion, solvent-based liquid materials (previously named 3D-Paints) which solidify nearly instantaneously upon deposition and contain a majority by volume of solid particulate material. In prior work, the dissolved polymer binder which enables this process is a high molecular weight biocompatible elastomer, poly(lactic-co-glycolic) acid (PLGA). We demonstrate in this study an expansion of this solvent-based 3D-Paint system to two additional, less-expensive, and less-specialized polymers, polystyrene (PS) and polyethylene oxide (PEO). The polymer binder used within the 3D-Paint was shown to significantly affect the as-printed and thermal postprocessing behavior of printed structures. This development enables users to select one of several polymers to impart the most desirable properties for a given application. Additionally, 3D-Paints based on these new binders are not adversely affected by classes of particles that can chemically degrade PLGA, notably particles containing large quantities of alkali ions. This study demonstrates the ability to successfully use PS and PEO as binders in the 3D-Paint system and compares the rheological, mechanical, microstructural, and thermal properties of the modified 3D-Paints and resulting as-printed and thermally post-processed objects. These objects include, for the first time, structures resulting from 3D-Painting which mostly contain soda-lime glass and 45S5 bioactive glass.

Fine structuration of low-temperature co-fired ceramic (LTCC) microreactors

The development of microreactors that operate under harsh conditions is always of great interest for many applications. Here we present a microfabrication process based on low-temperature co-fired ceramic (LTCC) technology for producing microreactors which are able to perform chemical processes at elevated temperature (>400 °C) and against concentrated harsh chemicals such as sodium hydroxide, sulfuric acid and hydrochloric acid. Various micro-scale cavities and/or fluidic channels were successfully fabricated in these microreactors using a set of combined and optimized LTCC manufacturing processes. Among them, it has been found that laser micromachining and multi-step low-pressure lamination are particularly critical to the fabrication and quality of these microreactors. Demonstration of LTCC microreactors with various embedded fluidic structures is illustrated with a number of examples, including micro-mixers for studies of exothermic reactions, multiple-injection microreactors for ionone production, and high-temperature microreactors for portable hydrogen generation.

Preparation of continuous gold nanowires by electrospinning of high-concentration aqueous dispersions of gold nanoparticles

Gold nanowires are prepared by the electrospinning of highly concentrated aqueous dispersions of gold nanoparticles (AuNPs) in the presence of poly(vinyl alcohol) and subsequent annealing at higher temperatures. Continuous wires of sintered AuNPs are obtained as a result of this process. The Au wires are characterized by transmission electron microscopy, helium ion microscopy, optical microscopy, and X-ray diffractometry.

Effect of material, process parameters, and simulated body fluids on mechanical properties of 13-93 bioactive glass porous constructs made by selective laser sintering

The effect of particle size distribution, binder content, processing parameters, and sintering schedule on the microstructure and mechanical properties of porous constructs was investigated. The porous constructs were produced by indirect selective laser sintering (SLS) of 13-93 bioactive glass using stearic acid as a polymeric binder. The binder content and d(50) particle size in the feedstock powders were simultaneously reduced from 22 to 12 wt% and from 20 to 11 μm, respectively, to identify the minimum binder content required for the SLS fabrication. An average particle size of ∼16 μm with a binder content of 15 wt% significantly reduced post-processing time and improved mechanical properties. Increasing the laser power and scan speed at the energy density of 1 cal/cm² maintained the feature sharpness of the parts during the fabrication of green parts and could almost double the mechanical properties of the sintered parts. Changes in the heating rates, ranging from 0.1 to 2 °C/min, during the post-processing of the fabricated "green" scaffolds showed that the heating rate significantly affects the densification and mechanical properties of the sintered scaffolds. The compressive strength of the scaffolds manufactured with the optimized parameters varied from 41 MPa, for a scaffold with a porosity of ∼50%, to 157 MPa, for a dense part. The bioactive scaffolds soaked in simulated body fluids for durations up to 6 weeks were used to evaluate the change in mechanical properties in vitro.

Electrospun core-shell fibers for robust silicon nanoparticle-based lithium ion battery anodes

Because of its unprecedented theoretical capacity near 4000 mAh/g, which is approximately 10-fold larger compared to those of the current commercial graphite anodes, silicon has been the most promising anode for lithium ion batteries, particularly targeting large-scale energy storage applications including electrical vehicles and utility grids. Nevertheless, Si suffers from its short cycle life as well as the limitation for scalable electrode fabrication. Herein, we develop an electrospinning process to produce core-shell fiber electrodes using a dual nozzle in a scalable manner. In the core-shell fibers, commercially available nanoparticles in the core are wrapped by the carbon shell. The unique core-shell structure resolves various issues of Si anode operations, such as pulverization, vulnerable contacts between Si and carbon conductors, and an unstable sold-electrolyte interphase, thereby exhibiting outstanding cell performance: a gravimetric capacity as high as 1384 mAh/g, a 5 min discharging rate capability while retaining 721 mAh/g, and cycle life of 300 cycles with almost no capacity loss. The electrospun core-shell one-dimensional fibers suggest a new design principle for robust and scalable lithium battery electrodes suffering from volume expansion.

Nuclear magnetic resonance-compatible furnace for high temperature MR imaging and spectroscopy in situ

A high temperature magnetic resonance compatible furnace for real time in situ monitoring of materials, processes, and chemical reactions with magnetic resonance imaging and spectroscopy is described. Design issues are analyzed. Example applications are demonstrated with a time sequence of proton images of the binder burnout in a porous green ceramic cylinder containing polyethylene glycol binder at 200 degrees C, and 7Li images of the molten salt LiCl at 700 degrees C.