Role of cone beam computed tomography in rehabilitation of a traumatised deficient maxillary alveolar ridge using symphyseal block graft placement

Pattern of buccal and palatal bone density in the maxillary premolar region: an anatomical basis of anterior-middle superior alveolar (AMSA) anesthetic technique

Background

The anterior-middle superior alveolar (AMSA) anesthetic technique has been reported to be a less traumatic alternative to several conventional nerve blocks and local infiltration for anesthesia of the maxillary teeth, their periodontium, and the palate. However, its anatomic basis remains controversial. The present study aimed to determine if the pattern of cortical and cancellous bone density in the maxillary premolar region can provide a rationale for the success of the AMSA anesthetic technique.

Methods

Cone-beam computed tomography scans of 66 maxillary quadrants from 34 patients (16 men and 18 women) were evaluated using a volumetric imaging software for cortical and cancellous bone densities in three interdental regions between the canine and first molar. Bone density was measured in Hounsfield units (HU) separately for the buccal cortical, palatal cortical, buccal cancellous, and palatal cancellous bones. Mean HU values were compared using the Mann-Whitney U test and one-way ANOVA with post-hoc analysis.

Results

Cancellous bone density was significantly lower (P ≤ 0.001) in the palatal half than in the buccal half across all three interdental regions. However, there was no significant difference (P = 0.106) between the buccal and palatal cortical bone densities at the site of AMSA injection. No significant difference was observed between the two genders for any of the evaluated parameters.

Conclusions

The palatal half of the cancellous bone had a significantly lower density than the buccal half, which could be a reason for the effective diffusion of the anesthetic solution following a palatal injection during the AMSA anesthetic technique.

Rehabilitation of Edentulous Jaws with Full-Arch Fixed Implant-Supported Prostheses: An Approach with Short and Ultrashort Implants and Metal-Free Materials

Introduction. Short implants represent a valid alternative to bone regeneration techniques. In addition, metal-free prosthetic materials have several advantages for predictable rehabilitation. This case report is aimed at illustrating the advantages of fixed implant-prosthetic rehabilitation on short and ultrashort implants and metal-free prosthetic materials. Case report. A 66-year-old male patient with bone atrophy was treated with temporary denture placement performed based on a rapid protocol. Once the tissues after extractions matured and aesthetic/function was studied, short implants were prosthetically placed, and a fiber-reinforced composite (FRC) bar was digitally designed for a double full-arch fixed rehabilitation. The 2-year follow-up showed the absence of peri-implantitis signs and a stable occlusal relationship of prostheses. Discussion and conclusions. The FRC material has excellent aesthetic properties and is low cost with a simplified and fast workflow owing to digital dentistry methods. Further studies are still needed to confirm the effectiveness of long-term therapy; however, the combination of new minimally invasive surgery and prosthetic advances seems to be very promising.

Hard- and soft-tissue augmentation around dental implant using ridge split and connective tissue graft for esthetic rehabilitation of atrophic anterior maxilla

Esthetic rehabilitation of edentulous site with horizontal ridge deficiency presents as one of the most challenging situations in implant practice. With the increase in popularity of dental implants, augmentation of the alveolar ridge and soft tissue has also become a routine procedure in most of the cases. Although hard-tissue augmentation is performed by other specialists also, a periodontist needs to master the skills of soft-tissue management to deliver esthetic and functional results in implant-supported prostheses. This case report presents a single-staged ridge split approach using piezoelectric surgery with simultaneous implant placement followed by connective tissue grafting at second-stage surgery. Single-staged segmental ridge split technique not only reduces the total treatment duration but also the surgical morbidity for the patient. A subepithelial connective tissue graft is strongly advocated around implants as it is highly predictable while ensuring better esthetic results in terms of tissue color, texture, and long-term stability of the surrounding mucosa.

Custom-Made Computer-Aided-Design/Computer-Aided-Manufacturing Biphasic Calcium-Phosphate Scaffold for Augmentation of an Atrophic Mandibular Anterior Ridge

This report documents the clinical, radiographic, and histologic outcome of a custom-made computer-aided-design/computer-aided-manufactured (CAD/CAM) scaffold used for the alveolar ridge augmentation of a severely atrophic anterior mandible. Computed tomographic (CT) images of an atrophic anterior mandible were acquired and modified into a 3-dimensional (3D) reconstruction model; this was transferred to a CAD program, where a custom-made scaffold was designed. CAM software generated a set of tool-paths for the manufacture of the scaffold on a computer-numerical-control milling machine into the exact shape of the 3D design. A custom-made scaffold was milled from a synthetic micromacroporous biphasic calcium phosphate (BCP) block. The scaffold closely matched the shape of the defect: this helped to reduce the time for the surgery and contributed to good healing. One year later, newly formed and well-integrated bone was clinically available, and two implants (AnyRidge, MegaGen, Gyeongbuk, South Korea) were placed. The histologic samples retrieved from the implant sites revealed compact mature bone undergoing remodelling, marrow spaces, and newly formed trabecular bone surrounded by residual BCP particles. This study demonstrates that custom-made scaffolds can be fabricated by combining CT scans and CAD/CAM techniques. Further studies on a larger sample of patients are needed to confirm these results.