Influence of Deformation and Stress between Bone and Implant from Various Bite Forces by Numerical Simulation Analysis

Prospective evaluation of implants-supported, tooth-implant supported, and teeth-supported 3-unit posterior monolithic zirconia fixed restorations: Bite force and patient satisfaction

OBJECTIVES

This study aimed to evaluate the maximum bite force (MBF) and satisfaction of patients restored with implants, combined tooth-implants, and teeth-supported monolithic zirconia fixed dental prostheses (FDPs).

MATERIALS AND METHODS

Thirty partially edentulous patients in need of three units of FDPs in their mandibular posterior region were divided into three equal groups (n = 10) as follows: Group-1 patients received two implants for each at the second premolar and second molar regions, Group-2 patients received one implant for each at the second molar region, and Group-3 patients with missing lower first molar. All the restorations were constructed from monolithic zirconia. Patients were evaluated 1 week after placement of restorations (baseline) and then after 6, 12, and 24-month intervals for MBF using force transducer occlusal force meter and satisfaction (function, esthetic, and overall satisfaction) using a visual analog scale.

RESULTS

The mean MBF for Group 1 was higher than Group 2 (p = .044) but not that of Group 3 (p = .923). Additionally, Group 3 displayed a higher MBF than Group 2, although this difference was not statistically significant (p = .096). Concerning patient satisfaction, all study groups reported high levels of satisfaction across all satisfaction elements, and no significant differences were observed between the groups.

CONCLUSION

Within the limitations of this study, it can be concluded that Group 1 gives comparable anticipated treatment outcomes as Group 3 concerning biting force and patient satisfaction. However, Group 2 gives comparable satisfaction results with biting force value within the normal range; thus, it might be used as a treatment option in a specific situation.

Stability Analysis of Plate-Screw Fixation for Femoral Midshaft Fractures

An understanding of the biomechanical characteristics and configuration of flexible and locked plating in order to provide balance stability and flexibility of implant fixation will help to construct and promote fast bone healing. The relationship between applied loading and implantation configuration for best bone healing is still under debate. This study aims to investigate the relationship between implant strength, working length, and interfragmentary strain (εIFM) on implant stability for femoral midshaft transverse fractures. The transverse fracture was fixed with a fragment locking compression plate (LCP) system. Finite element analysis was performed and subsequently characterised based on compression loading (600 N up to 900 N) and screw designs (conventional and locking) with different penetration depths (unicortical and bicortical). Strain theory was used to evaluate the stability of the model. The correlation of screw configuration with screw type shows a unicortical depth for both types (p < 0.01) for 700 N and 800 N loads and (p < 0.05) for configurations 134 and 124. Interfragmentary strain affected only the 600 N load (p < 0.01) for the bicortical conventional type (group BC), and the screw configurations that were influenced were 1234 and 123 (p < 0.05). The low steepness of the slope indicates the least εIFM for the corresponding biomechanical characteristic in good-quality stability. A strain value of ≤2% promotes callus formation and is classified as absolute stability, which is the minimum required value for the induction of callus and the maximum value that allows bony bridging. The outcomes have provided the correlation of screw configuration in femoral midshaft transverse fracture implantation which is important to promote essential primary stability.

Self-Searching Writing of Human-Organ-Scale Three-Dimensional Topographic Scaffolds with Shape Memory by Silkworm-like Electrospun Autopilot Jet

Bioengineered scaffolds satisfying both the physiological and anatomical considerations could potentially repair partially damaged tissues to whole organs. Although three-dimensional (3D) printing has become a popular approach in making 3D topographic scaffolds, electrospinning stands out from all other techniques for fabricating extracellular matrix mimicking fibrous scaffolds. However, its complex charge-influenced jet-field interactions and the associated random motion were hardly overcome for almost a century, thus preventing it from being a viable technique for 3D topographic scaffold construction. Herein, we constructed, for the first time, geometrically challenging 3D fibrous scaffolds using biodegradable poly(ε-caprolactone), mimicking human-organ-scale face, female breast, nipple, and vascular graft, with exceptional shape memory and free-standing features by a novel field self-searching process of autopilot polymer jet, essentially resembling the silkworm-like cocoon spinning. With a simple electrospinning setup and innovative writing strategies supported by simulation, we successfully overcame the intricate jet-field interactions while preserving high-fidelity template topographies, via excellent target recognition, with pattern features ranging from 100's μm to 10's cm. A 3D cell culture study ensured the anatomical compatibility of the so-made 3D scaffolds. Our approach brings the century-old electrospinning to the new list of viable 3D scaffold constructing techniques, which goes beyond applications in tissue engineering.

Relationships of Stresses on Alveolar Bone and Abutment of Dental Implant from Various Bite Forces by Three-Dimensional Finite Element Analysis

Occlusal trauma caused by improper bite forces owing to the lack of periodontal membrane may lead to bone resorption, which is still a problem for the success of dental implant. In our study, to avoid occlusal trauma, we put forward a hypothesis that a microelectromechanical system (MEMS) pressure sensor is settled on an implant abutment to track stress on the abutment and predict the stress on alveolar bone for controlling bite forces in real time. Loading forces of different magnitudes (0 N–100 N) and angles (0–90°) were applied to the crown of the dental implant of the left central incisor in a maxillary model. The stress distribution on the abutment and alveolar bone were analyzed using a three-dimensional finite element analysis (3D FEA). Then, the quantitative relation between them was derived using Origin 2017 software. The results show that the relation between the loading forces and the stresses on the alveolar bone and abutment could be described as 3D surface equations associated with the sine function. The appropriate range of stress on the implant abutment is 1.5 MPa–8.66 MPa, and the acceptable loading force range on the dental implant of the left maxillary central incisor is approximately 6 N–86 N. These results could be used as a reference for the layout of MEMS pressure sensors to maintain alveolar bone dynamic remodeling balance.

Load response of the natural tooth and dental implant: A comparative biomechanics study

PURPOSE

While dental implants have displayed high success rates, poor mechanical fixation is a common complication, and their biomechanical response to occlusal loading remains poorly understood. This study aimed to develop and validate a computational model of a natural first premolar and a dental implant with matching crown morphology, and quantify their mechanical response to loading at the occlusal surface.

MATERIALS AND METHODS

A finite-element model of the stomatognathic system comprising the mandible, first premolar and periodontal ligament (PDL) was developed based on a natural human tooth, and a model of a dental implant of identical occlusal geometry was also created. Occlusal loading was simulated using point forces applied at seven landmarks on each crown. Model predictions were validated using strain gauge measurements acquired during loading of matched physical models of the tooth and implant assemblies.

RESULTS

For the natural tooth, the maximum vonMises stress (6.4 MPa) and maximal principal strains at the mandible (1.8 mε, −1.7 mε) were lower than those observed at the prosthetic tooth (12.5 MPa, 3.2 mε, and −4.4 mε, respectively). As occlusal load was applied more bucally relative to the tooth central axis, stress and strain magnitudes increased.

CONCLUSION

Occlusal loading of the natural tooth results in lower stress-strain magnitudes in the underlying alveolar bone than those associated with a dental implant of matched occlusal anatomy. The PDL may function to mitigate axial and bending stress intensities resulting from off-centered occlusal loads. The findings may be useful in dental implant design, restoration material selection, and surgical planning.

Effect of thread depth and implant shape on stress distribution in anterior and posterior regions of mandible bone: A finite element analysis

BACKGROUND

The ability of modern implant dentistry to achieve goals such as normal contour, function, comfort, esthetics, and health to totally or partially edentulous patients guaranteed it to be more effective and reliable method for the rehabilitation process of many challenging clinical situations. In regard to this, the current study evaluates the effect of changing implant shape design parameters on interface stress distribution within the mandible bone.

MATERIALS AND METHODS

A numerical procedure based on finite element (FE) method was adopted to investigate the influence of using different body design and thread depth of the inserted implant on the final stress situation. For the purpose of evaluation, a three-dimensional realistic FE models of mandible bone and inserted implant were constructed and analyzed using a pack of engineering software (Solidworks, and ANSYS). Six different commercial implant models (cylindrical and tapered) with three different V-shaped thread depths (0.25 mm, 0.35 mm, and 0.45 mm) were designed to be used in this study. The suggested implants used in this study were threaded in two different locations of mandible bone; the anterior region (Type I model) and posterior region (Type II model). A vertical static load of 250 N was directly applied to the center of the suprastructure of the implant for each model.

RESULTS

For both models, evaluations were achieved to figure out the stress distribution patterns and maximum equivalent von Mises. The results obtained after implementation of FE dental-implant models show that the highest stresses were located at the crestal cortical bone around the implant neck. In addition, the simulation study revealed that taper body implant had a higher peak value of von Mises stress than that of cylinder body implants in all types of bones. Moreover, a thread depth of 0.25 mm showed highest peak of maximum von Mises stresses for Type I and Type II models.

CONCLUSION

The simulation results indicate that all models have the same von Mises stress distribution pattern and higher peak von Mises stresses of the cortical bone were seen in tapered implant body in contrast to the cylindrical body.

Shape Optimization of Bone-Bonding Subperiosteal Devices with Finite Element Analysis

Subperiosteal bone-bonding devices have been proposed for less invasive treatments in orthodontics. The device is osseointegrated onto a bone surface without fixation screws and is expected to rapidly attain a bone-bonding strength that successfully meets clinical performance. Hence, the device's optimum shape for rapid and strong bone bonding was examined in this study by finite element analyses. First, a stress analysis was performed for a circular rod device with an orthodontic force parallel to the bone surface, and the estimate of the bone-bonding strength based on the bone fracture criterion was verified with the results of an animal experiment. In total, four cross-sectional rod geometries were investigated: circular (Cr), elliptical (El), semicircular (Sc), and rectangular (Rc). By changing the height of the newly formed bone to mimic the progression of new bone formation, the estimation of the bone-bonding strength was repeated for each geometry. The rod with the Rc cross section exhibited the best performance, followed by those with the Sc, El, and Cr cross sections, from the aspects of the rapid acquisition of strength and the strength itself. Thus, the rectangular cross section is the best for rod-like subperiosteal devices for rapid bone bonding.