Microbiological Sealing Analysis of a Tapered Connection and External Hexagon System

In vitro analysis of prosthetic abutment and angulable frictional implant interface adaptation: Mechanical and microbiological study

The aim of this study was to evaluate, in vitro, the microbiological sealing at the implant and different angles frictional prosthetic abutment interface, submitted or not to mechanical cycling, as well as the deactivation force and evaluation of the implant-abutment interface by scanning electron microscopy. For this study, the sealing capacity of eighty sets of abutments/implants of each angle, with and without mechanical cycling, with internal conical connection (locking tapper) (4.3 mm × 9.0 mm) constituted in Titanium alloy (Ti6Al4V), and stainless steel angled prosthetic abutment was evaluated (18Cr14Ni2.5Mo) according to ASTM F138-13a (Arcsys, FGM, Joinville, Brazil), 6 mm high and 4.2 mm in diameter at the coronary portion, and 3.5 mm high transmucosal, in 4 different angles (0, 5, 10 and 20°). After in vitro tests, 100% biological sealing was observed at the implant / prosthetic abutment interface within cycled and non-cycled conditions, for the straight, 5, 10 and 20° inclination groups. There was no statistically significant difference in the removal force of the prosthetic abutments at different angles, under non-cycled conditions; however, under mechanical loading, the deactivation force was significantly higher for straight prosthetic abutments than with 10 and 20° of angulation. Surface analysis revealed good adaptation between implants and abutments, and the presence of wear areas, independently of mechanical loading. It is concluded that the analysis of implant and prosthetic abutment interface revealed good adaptation between the parts, for all analyzed samples.

Performance of different abutment/implant joints as a result of a sealing agent

Purpose This in vitro study aimed to evaluate the effectiveness of a sealing agent in sealing the abutment/implant interface and the preload maintenance of retaining screws after mechanical cycling.Methods Six groups (n = 12) were evaluated according to the abutment/implant system (external-hexagon implant and UCLA abutments, EHU; Morse taper implant and UCLA abutments, MTU; and Morse taper implant and flexcone abutments, MTF) and the presence of an anaerobic gel sealing agent (control group, no sealing agent; experimental group, sealing agent). Toluidine blue (0.7 μL) was inserted into each implant and the abutments were attached to the implants using a digital torque wrench to evaluate the sealing of the abutment/implant interface. The specimens were tested through mechanical cycling (1 × 10⁶ cycles, 2 Hz, and 130 N). Dye release from the abutment/implant interface was analyzed using a spectrophotometer, and the reverse torque values were obtained using a digital wrench. Reverse torque and dye release data were measured after mechanical cycling and analyzed using ANOVA and Tukey's test (α =.05).Results All experimental groups showed higher reverse torque values than the control groups (P <.05). In general, the MTU and MTF experimental groups, as well as the MTF control group, showed no significant dye release at different periods (P >.05).Conclusions The use of a sealing agent improved the preload maintenance of screw-retained implant-supported prostheses. The sealing agent was effective in sealing the Morse taper connection.

Behavior of implant and abutment sets of three different connections during the non-axial load application: An in vitro experimental study using a radiographic method

BACKGROUND

During the masticatory cycle, loads of different intensities and directions are received by the dental structures and/or implants, which can cause micromovements at the junction between the abutment and implant.

OBJECTIVE

The objective of this in vitro study was to evaluate the behavior of three different implant connections subjected to different load values using a digital radiography system. Additionally, the torque values for removing the abutment screws were also measured and compared.

METHODS

Ninety sets of implant and abutment (IA) were used, divided into three groups according to the type of connection (n = 30 per group): EH group, external hexagon type connection; IH group, internal hexagon connection; and, MT group, Morse taper connection.

RESULTS

MT group showed the better vertical misfit behavior at the three intensity of load applied, in comparison with EH and IH groups. In the analysis of torque maintenance (detorque test), MT group showed higher values of detorque when compared with the measured values of EH and IH groups (p < 0.001).

CONCLUSIONS

The IA sets of EH and IH groups showed a microgap in all levels of applied loads, unlike the MT group this event was not observed. In the detorque test, MT group increase in the torque values when compared to the initial torque applied, unlike EH and IH groups showed a decrease in the initially torque applied in all conditions tested. A positive correlation was detected between the misfit and detorque values.

The Impact of Implant-Abutment Connection on Clinical Outcomes and Microbial Colonization: A Narrative Review

INTRODUCTION

Osseointegration are often suffering from oral conditions, especially, the micro gap at the implant-abutment connection represents a site for bacterial plaque aggregation, leading to increased inflammatory cells and causing peri-implantitis.

AIM

The aim of this narrative review was to describe the different kinds of implant-abutment connections and their ability to reduce bacterial leakage and thus prevent peri-implantitis.

MATERIALS AND METHODS

The following databases were consulted: Pubmed, Scopus, Cochrane Library, and Research gate and a total of 528 articles were found. After reading the abstract and titles, 473 items were excluded. The remaining articles (n = 55) were assessed for full-text eligibility. Thirty-three studies were included in the review.

RESULTS AND CONCLUSIONS

We selected 22 clinical trials and 11 reviews, examining a total sample of 2110 implants. From the review, it was clear that there exists a relationship between the implant-abutment interface and bacterial leakage. All the connections presented an amount of micro-gap and bacterial micro-leakage, though conical and mixed connection systems seemed to behave better. Moreover, both connections seemed to have a better load distribution and the mixed system also had anti-rotational properties which are very useful during the positioning of the prosthesis.