Tailoring the porosity of chemically activated carbons derived from the HTC treatment of sewage sludge for the removal of pollutants from gaseous and aqueous phases

The management of sewage sludge is currently an open issue due to the large volume of waste to be treated and the necessity to avoid incineration or landfill disposal. Hydrothermal carbonization (HTC) has been recognized as a promising thermochemical technique to convert sewage sludge into value-added products. The hydrochar (HC) obtained can be suitable for environmental application as fuel, fertilizer, and sorbent. In this study, activated hydrochars (AHs) were prepared from sewage sludge through HTC followed by chemical activation with potassium hydroxide (KOH) and tested for the removal of pollutants in gaseous and aqueous environments, investigating carbon dioxide (CO2) and ciprofloxacin (CIP) adsorption capacity. The effects of activation temperature (550-750 °C) and KOH/HC impregnation ratio (1-3) on the produced AHs morphology and adsorption capacity were studied by Response Surface Methodology (RSM). The results of RSM analysis evidenced a maximum CO2 uptake of 71.47 mg/g for mild activation conditions (600-650 °C and KOH/HC = 1 ÷ 2), whereas the best CIP uptake of 628.61 mg/g was reached for the most severe conditions (750 °C, KOH/HC = 3). The prepared AHs were also applied for the removal of methylene blue (MB) from aqueous solutions, and the MB uptake results were used for estimating the specific surface area of AHs. High surface areas up to 1902.49 m2/g were obtained for the highest activation temperature and impregnation ratio investigated. Predictive models of CO2 and CIP uptake were developed by RSM analysis, and the optimum activation conditions for maximizing the adsorption performance together with high AH yield were identified: 586 °C and KOH/HC ratio = 1.34 for maximum yield (26.33 %) and CO2 uptake (67.31 mg/g); 715 °C and KOH/HC ratio = 1.78 for maximum yield (18.75 %) and CIP uptake (370.77 mg/g). The obtained results evidenced that chemical activation of previously HTC-treated sewage sludge is a promising way to convert waste into valuable low-cost adsorbents.

Enhanced Assembling of N-and-K-Riched Macroalgae as Carbon Adsorbent for CO2 Capture with Ni(NO3)2/KOH as Co-Catalysts

Porous-activated carbons have drawn great attention due to their important role in CO2 capture. Ni(NO3)2/KOH, as co-catalysts under different temperatures, were studied to obtain porous graphitized carbon from Sargassum horneri feedstock. The results indicated that the properties of the porous graphitized carbon generated at 850 °C were greatly enhanced, showing a large specific surface area of 1486.38 cm3·g-1 with narrowly distributed micropores (~0.67 nm) and abundant functional groups, which endowed high CO2 uptake; moreover, the high CO2 uptake was mainly attributed to the synergistic effect of Ni(NO3)2 and KOH, both in chemical modification and pore formation. The fitted values of the four kinetic models showed that the double exponential model provided the best description of carbon adsorption, indicating both physical and chemical adsorption. It is worth noting that carbon could be reused four times in the adsorption/desorption procedure in this research with good stability. This work focuses on the high-value-added comprehensive utilization of macroalgae, which not only is important for high-performance adsorbent preparation but also has positive benefits for the development and utilization of macroalgae resources.

Comparative Study of CO2 Capture by Adsorption in Sustainable Date Pits-Derived Porous Activated Carbon and Molecular Sieve

The rising CO₂ concentration has prompted the quest of innovative tools to reduce its effect on the environment. A comparative adsorption study using sustainable low-cost date pits-derived activated carbon and molecular sieve has been carried out for CO₂ separation. The adsorb ents were characterized for surface area and morphological properties. The outcomes of flow rate, temperature and initial adsorbate concentration on adsorption performance were examined. The process effectiveness was investigated by breakthrough time, adsorbate loading, efficiency, utilized bed height, mass transfer zone and utilization factor. The immensely steep adsorption response curves demonstrate acceptable utilization of adsorbent capability under breakthrough condition. The adsorbate loading 73.08 mg/g is achieved with an 0.938 column efficiency for developed porous activated carbon at 298 K. The reduced 1.20 cm length of mass transfer zone with enhanced capacity utilization factor equal 0.97 at 298 K with C_in = 5% signifies better adsorption performance for date pits-derived adsorbent. The findings recommend that produced activated carbon is greatly promising to adsorb CO₂ in fixed bed column under continuous mode.

CO2 Capture by Low-Cost Date Pits-Based Activated Carbon and Silica Gel

The rising levels of CO2 in the atmosphere are causing escalating average global temperatures. The capture of CO2 by adsorption has been carried out using silica gel type III and prepared activated carbon. The date pits-based activated carbon was synthesized using a tubular furnace by physical activation. The temperature of the sample was increased at 10 °C/min and the biomass was carbonized under N2 flow maintained continuously for 2 h at 600 °C. The activation was performed with the CO2 flow maintained constantly for 2 h at 600 °C. The temperature, feed flow and adsorbate volume were the parameters considered for CO2 adsorption. The success of CO2 capture was analyzed by CO2 uptake, efficiency based on column capacity, utilization factors and the mass transfer zone. The massively steep profiles of the breakthrough response of the AC demonstrate the satisfactory exploitation of CO2 uptake under the conditions of the breakthrough. The SG contributed to a maximal CO2 uptake of 8.61 mg/g at 298 K and Co = 5% with F = 5 lpm. The enhanced CO2 uptake of 73.1 mg/g was achieved with a column efficiency of 0.94 for the activated carbon produced from date pits at 298 K. The AC demonstrated an improved performance with a decreased mass transfer zone of 1.20 cm with an enhanced utilization factor f = 0.97 at 298 K. This finding suggests that a date pits-based activated carbon is suitable for CO2 separation by adsorption from the feed mixture.

Acetic acid-mediated cellulose-based carbons: Influence of activation conditions on textural features and carbon dioxide uptakes

In this work, we developed a simple methodology for producing highly porous carbons. Herein, we combined the hydrothermal method with chemical activation to fabricate cellulose-based, melamine modified porous carbons, using acetic acid as an additive. The preparation conditions including activation temperature, activation time, and melamine ratio were varied to obtain an optimized adsorbent exhibiting efficient textural features and maximized carbon dioxide (CO₂) adsorption uptake. By varying the preparation conditions, high specific surface area (SSA) (1260-3019 m² g^-1), microporosity in the range of 0.21-1.13 cm³ g^-1, and a well-developed porous structure was obtained. The optimized adsorbent exhibits an excellent CO₂ adsorption uptake of 297.05 mg g^-1 (6.75 mmol g^-1) and 174.4 mg g^-1 (3.96 mmol g^-1) at 273 K and 298 K at 1 bar, respectively, due to the existence of ultra-micropores (<0.68 nm, < 0.81 nm), high SSA (3019 m² g^-1), and high nitrogen content (8%). Furthermore, the role of micropores in the CO₂ adsorption process suggests that micropores between 0.68 nm and 1 nm exhibit high CO₂ adsorption potential. Additionally, all synthesized carbons exhibited a high isosteric heat of adsorption (45 kJ mol^-1) and a greater affinity for adsorbed CO₂ species than nitrogen (N₂) molecules. Thus, as-fabricated porous carbon adsorbents are an effective competitor for CO₂ uptake applications to mitigate global warming.

Synthesis and characterization of high-performance activated carbon from walnut shell biomass for CO2 capture

An increasing level of carbon dioxide (CO₂) in the atmosphere has ultimately resulted in global warming and climate change. The high-performance activated carbon (AC-WL) was synthesized from walnut shell, a low-cost biomass by-product, by physical activation using a tube furnace. The adsorption behavior of CO₂ from the CO₂/N₂ mixture was investigated using a fixed bed. The surface and morphological characterizations of the produced activated carbons were measured using a BET analyzer and a scanning electron microscope (SEM). The effect of temperature, flow rate, CO₂ level, and partial pressure on breakthrough behavior was analyzed, and the adsorption response presented in terms of breakthrough point and adsorption capacity. The breakthrough and saturation periods vary significantly with change in temperature. The steepness of the breakthrough curves signifies good utilization of adsorbent capacity at breakthrough point. The increase in temperatures and flow rates lead to an increase in the length of mass transfer zone. The adsorption capacity of 1.58 mmol/g was obtained at 1.30 bars and 293 K with higher capacity utilization factor of 0.8492.These results suggest that the walnut-based activated carbon is favorable for capturing CO₂.