Adsorption of methyl orange on low-cost adsorbent natural materials and modified natural materials: a review

Recently a large number of extensive studies have amassed that describe the removal of dyes from water and wastewater using natural adsorbents and modified materials. Methyl orange dye is found in wastewater streams from various industries that include textiles, plastics, printing and paper among other sources. This article reviews methyl orange adsorption onto natural and modified materials. Despite many techniques available, adsorption stands out for efficient water and wastewater treatment for its ease of operation, flexibility and large-scale removal of colorants. It also has a significant potential for regeneration recovery and recycling of adsorbents in comparison to other water treatment methods. The adsorbents described herein were classified into five categories based on their chemical composition: bio-sorbents, activated carbon, biochar, clays and minerals, and composites. In this review article, we want to demonstrate the capacity of natural and modified materials for dye adsorption which can yield significant improvements to the adsorption capacity of dyes such as methyl orange. In addition, the effect of critical variables including contact time, initial methyl orange concentration, dosage of adsorbent, pH, temperature and mechanism on the adsorption efficiency will be covered as part of this literature review.

Investigation of the removal kinetics, thermodynamics and adsorption mechanism of anionic textile dye, Remazol Red RB, with powder pumice, a sustainable adsorbent from waste water

Excessive growth and abnormal use of dyes and water in the textile industry cause serious environmental problems, especially with excessive pollution of water bodies. Adsorption is an attractive, feasible, low-cost, highly efficient and sustainable technique in terms of green chemistry for the removal of pollutants from water. This study aims to investigate the removal kinetics, thermodynamics and adsorption mechanism of Remazol Red RB, which was chosen as a representative anionic reactive dye, from synthetic wastewater using powdered pumice, taking into account various experimental parameters such as initial dye concentration, adsorption time, temperature and pH. Moreover, to support the proposed adsorption mechanism, before and after adsorption of the samples, the Fourier transform infrared spectrophotometer (FTIR) spectra, X-ray powder diffraction (XRD) diffractograms and High resolution transmission electron microscopy (HRTEM) images were also taken and used. The results show that powder pumice can be an efficient adsorbent for anionic dye removal with a relatively high adsorption capacity of 38.90 mg/g, and it is very effective in 30-60 min in mild conditions. The experimental data showed a high agreement with the pseudo-second-order kinetic model and the Freundlich adsorption isotherm equation. In addition, thermodynamically, the process exhibited exothermic nature and standard isosteric enthalpy and entropy changes of -4.93 kJ/mol and 16.11 J/mol. K were calculated. It was determined that the adsorption mechanism was predominantly based on T-shaped pi-pi interactions and had physical characteristics.

Chitin-Based Magnesium Oxide Biocomposite for the Removal of Methyl Orange from Water

In this work, a cost-effective chitin-based magnesium oxide (CHt@MgO) biocomposite with excellent anionic methyl orange (MO) dye removal efficiency from water was developed. The CHt@MgO biocomposite was characterized by FT-IR, XRD, SEM-EDX, and TGA/DTG. Results proved the successful synthesis of CHt@MgO biocomposite. Adsorption of MO on the CHt@MgO biocomposite was optimized by varying experimental conditions such as pH, amount of adsorbent (m), contact time (t), temperature (T), and initial MO concentration (C_o). The optimized parameters for MO removal by CHt@MgO biocomposite were as follows: pH, 6; m, 2 g/L; t, 120 min. Two common isotherm models (Langmuir and Freundlich) and three kinetic models (pseudo-first-order (PFO), pseudo-second-order (PSO), and intraparticle diffusion (IPD)) were tested for experimental data fitting. Results showed that Langmuir and PFO were the most suitable to respectively describe equilibrium and kinetic results on the adsorption of MO adsorption on CHt@MgO biocomposite. The maximum Langmuir monolayer adsorption capacity (q_m) on CHt@MgO biocomposite toward MO dye was 252 mg/g at 60 °C. The reusability tests revealed that CHt@MgO biocomposite possessed high (90.7%) removal efficiency after the fifth regeneration cycle.

Nano-Silica Modified with Diamine for Capturing Azo Dye from Aqueous Solutions

Nano-silica particles decorated with amine groups (S-DA) were prepared via a simple, one-pot method, and under very mild conditions in an attempt to improve the affinity of the silica nanoparticles toward capturing anionic organic dye, namely, methyl orange (MO). The prepared sample was characterized by different techniques such as XRD for crystallinity, SEM for morphological structure, TGA for thermal stability, BET surface area, and FTIR for surface functional groups. The prepared sample was tested for the removal of MO under different conditions including the mass of adsorbent, pH, initial concentration, and time. Results showed that the adsorption of MO was very fast with equilibrium achieved in less than 30 min and a maximum removal efficiency of 100% for a mass to volume ratio of 10 g/3 L, a pH of 2.5, initial concentration of 10 mgL⁻¹, and under stagnant conditions. These results were compared with a bare nano-silica, which was not able to adsorb more than 3% after 24 h, indicating the important effect of amine groups. Furthermore, recycling the adsorbent was achieved by rinsing the MO-loaded adsorbent with a dilute solution of KOH. The adsorbent maintained 50% of its initial removal efficiency after four adsorption–desorption cycles.

Production and Optimization of Bio-Based Silica Nanoparticle from Teff Straw (Eragrostis tef) Using RSM-Based Modeling, Characterization Aspects, and Adsorption Efficacy of Methyl Orange Dye

The brown teff straw was utilized in this study to produce silica using the sol-gel technique. After pretreatment, the raw material of brown teff straw was characterized. The data were analyzed using the central composite design and response surface technique, and four independent parameters, namely, temperature, NaOH concentration, rotational speed, and extraction time, were evaluated for process optimization. Before extracting silica with an alkaline solution, the silica content in the ash was determined using an AAS spectrometer. The silica content of teff straw ash is around 92.89%. The ash was treated with NaOH solution in the concentrations range of 1 M to 3 M (0.5 M interval). The extraction time varied at intervals of 55, 70, 85, 100, and 115 minutes. Temperatures were changed using magnetic stirrer equipment in the range of 80°C to 100°C (5°C interval). At 350 rpm, 400 rpm, 450 rpm, 500 rpm, and 550 rpm, the rotating speed was adjusted. The best extraction conditions for amorphous silica were 1.50 M NaOH, 109.99 min, 94.98°C, and a rotating speed of 499.57 rpm, with a maximum yield of 85.85%. XRD and FTIR analyses were used to assess the physicochemical characteristics of the extracted silica. The aqueous solutions of methyl orange were used to test the adsorption efficiency of silica. The percent of removal efficiency for methyl orange was 90.48%.

Anionic Dye Removal by Polypyrrole-Modified Red Mud and Its Application to a Lab-Scale Column: Adsorption Performance and Phytotoxicity Assessment

In this study, polypyrrole-modified red mud (PRM) was prepared for the efficient removal of anionic dyes (methyl orange and Congo red) from aqueous solutions. The phytotoxicity (bean sprouts) of the dye solution before and after dye removal was investigated. Adsorption kinetics confirmed that the adsorption of methyl orange (MO) and Congo red (CR) on PRM was controlled by chemical reactions between the functional groups of polypyrrole and dyes. From Langmuir isotherm fitting, we found the theoretical adsorption capacities of MO and CR on PRM were 194.1 and 314.9 mg/g, respectively. The adsorption progress of MO and CR on PRM was found to be spontaneous and endothermic. The column studies demonstrated that, under dynamic flow, the PRM can efficiently remove MO and CR from aqueous solution, with adsorption capacities of 31.08 and 55.04 mg/g, respectively. In the toxicity test, the phytotoxicity of the column effluents (after dye removal) was significantly lowered compared to the initial dye influents. After the removal of MO and CR, the average root length of bean sprouts was increased from 3.30 cm to 5.18 cm and from 3.01 cm to 7.00 cm, respectively. These findings highlighted the efficient removal of dyes by PRM from aqueous solution, demonstrating the possible application of PRM for the removal of dye from dye-contaminated wastewaters.

Aloe vera as Promising Material for Water Treatment: A Review

Aloe vera plant offers a sustainable solution for the removal of various pollutants from water. Due to its chemical composition, Aloe vera has been explored as coagulant/flocculant and biosorbent for water treatment. Most of the used materials displayed significant pollutants removals depending on the used preparation methods. AV-based materials have been investigated and successfully used as coagulant/flocculant for water treatment at laboratory scale. Selected AV-based materials could reduce the solids (total suspended solids (TSS), suspended solids (SS), total dissolved solids (TDS), and dissolved solids (DS)), turbidity, chemical oxygen demand (COD), biochemical oxygen demand (BOD), heavy metals, and color, with removal percentages varied depending on the coagulant/flocculant materials and on the wastewater characteristics. In the same context, AV materials can be used as biological flocculant for wastewater sludge treatment, allowing good solid–liquid separation and promoting sludge settling. Moreover, using different methods, AV material-based biosorbents were prepared and successfully used for pollutants (heavy metal dyes and phenol) elimination from water. Related results showed significant pollutant removal efficiency associated with an interesting adsorption capacity comparable to other biosorbents derived from natural products. Interestingly, the enzymatic system of Aloe vera (carboxypeptidase, glutathione peroxidase, and superoxide dismutase) has been exploited to degrade textile dyes. The obtained results showed high promise for removal efficiencies of various kinds of pollutants. However, results varied depending on the methodology used to prepare the Aloe vera based materials. Because of its valuable properties (composition, abundance, ecofriendly and biodegradable), Aloe vera may be useful for water treatment.

Activated Carbon for Dyes Removal: Modeling and Understanding the Adsorption Process

Batch adsorption experiments have been conducted to investigate the removal of methyl orange from aqueous solution by an activated carbon prepared from prickly pear seed cake by phosphoric acid activation. The adsorption process has been described by using kinetic and isotherm models. The kinetic of adsorption was examined by pseudo-first-order, pseudo-second-order, and intraparticle diffusion models. Adsorption isotherm was modeled using Langmuir, Freundlich, Temkin and Dubinin–Radushkevich isotherms. The adsorption process of methyl orange was well explained by the pseudo-second-order model and Freundlich isotherm. Also, pseudo-n-order model has been applied to estimate the order of adsorption kinetic and it was found equal to 2 which confirm the good accuracy of the pseudo-second order. Moreover, Dubinin–Radushkevich isotherm reveals that the adsorption of methyl orange onto activated carbon was a physisorption process in nature. The adsorption capacity of activated carbon was found to be 336.12 mg/g at temperature 20°C andpH∼7. These results demonstrated that the prickly pear seed cake is a suitable precursor for the preparation of appropriate activated carbon for dyes removal from aqueous solution.