A New Convenient Method to Assess Antibiotic Resistance and Antimicrobial Efficacy against Pathogenic Clostridioides difficile Biofilms

Clostridioides difficile is a widely distributed anaerobic pathogen. C. difficile infection is a serious problem in healthcare. Its biofilms have been found to exhibit biocorrosivity, albeit very little, but sufficient for it to correlate with biofilm growth/health. This work demonstrated the use of a disposable electrochemical biofilm test kit using two solid-state electrodes (a 304 stainless steel working electrode, and a graphite counter electrode, which also served as the reference electrode) in a 10 mL serum vial. It was found that the C. difficile 630∆erm Adp-4 mutant had a minimum inhibitory concentration (MIC) for vancomycin twice that of the 630∆erm wild type strain in biofilm prevention (2 ppm vs. 1 ppm by mass) on 304 stainless steel. Glutaraldehyde, a commonly used hospital disinfectant, was found ineffective at 2% (w/w) for the prevention of C. difficile 630∆erm wild type biofilm formation, while tetrakis(hydroxymethyl)phosphonium sulfate (THPS) disinfectant was very effective at 100 ppm for both biofilm prevention and biofilm killing. These antimicrobial efficacy data were consistent with sessile cell count and biofilm imaging results. Furthermore, the test kit provided additional transient biocide treatment information. It showed that vancomycin killed C. difficile 630∆erm wild type biofilms in 2 d, while THPS only required minutes.

Increased secretion of bacterial pyomelanin caused by light accelerates corrosion of low alloy steel

Microorganisms in the waterline zone can secrete pigments to avoid damage caused by ultraviolet radiation, some of which have corrosive effects. In this work, we found that the secretion of pyomelanin by P3 strain of Pseudoalteromonas lipolytica significantly increases under strong lighting conditions, accelerating the corrosion of the material. Molecular mechanisms indicate that strong light, as a stressful environmental factor, enhances the expression of melanin secretion-related genes to prevent bacteria from being damaged by ultraviolet radiation. Therefore, this work proposes a new corrosion mechanism in the waterline zone, pigment-producing microorganisms are also involved in the waterline corrosion process.

Effect of alloying element content on anaerobic microbiologically influenced corrosion sensitivity of stainless steels in enriched artificial seawater

Stainless steels (SS) are not immune to microbiologically influenced corrosion (MIC) especially in the presence of sulfate reducing bacteria (SRB). It is necessary to study the influence of alloying elements on the MIC. SRB MIC behaviors of four stainless steels (2205 SS, 316L SS, 304 SS, and 410 SS), with different alloying element compositions were compared after 14 days of incubation at 37°C in enriched artificial seawater inoculated with Desulfovibrio sp. The sessile cell sequence was 410 SS > 316L SS > 304 SS > 2205 SS, inversely proportional to Cr content. The uniform corrosion rate (based on weight loss) sequence was 410 SS > 304 SS > 316L SS > 2205 SS, which matches the pitting resistance equivalent number (PREN) sequence inversely. 410 SS with the lowest Cr and Mo contents suffered the most severe pitting, with pit depth of 35 μm and weight loss of 0.75 mg/cm² (0.91 mm/a pitting rate and 25 μm/a uniform corrosion rate). The other three stainless steels with higher Cr and Mo contents suffered only metastable pits. The semiconductor characteristics and the re-passivation abilities of the passive films were found to be affected by Cr and Mo contents.

Aggressive corrosion of carbon steel by Desulfovibrio ferrophilus IS5 biofilm was further accelerated by riboflavin

EET (extracellular electron transfer) is behind MIC (microbiologically influenced corrosion) of carbon steel by SRB (sulfate reducing bacteria). This work evaluated 20 ppm (w/w) riboflavin (an electron mediator) acceleration of C1018 carbon steel MIC by Desulfovibrio ferrophilus IS5 in enriched artificial seawater (EASW) after 7-d incubation in anaerobic vials at 28 °C. Twenty ppm riboflavin did not significantly change cell growth or alter the corrosion product varieties, but it led to 52% increase in weight loss and 105% increase in pit depth, compared to the control without 20 ppm riboflavin. With 20 ppm riboflavin supplement in EASW, D. ferrophilus yielded weight loss-based corrosion rate of 1.57 mm/y (61.8 mpy), and pit depth growth rate of 2.88 mm/y (113 mpy), highest reported for short-term pure-strain SRB MIC of carbon steel. Electrochemical tests in 450 mL glass cells indicated that the biofilm responded rather quickly to the riboflavin injection (20 ppm in broth) to the culture medium. Polarization resistance (R_p) began to decrease within minutes after injection. Within 2 h, the riboflavin injection led to 31% decrease in R_p and 35% decrease in R_ct + R_f from electrochemical impedance spectroscopy (EIS). The Tafel corrosion current density increased 63% 2 h after the injection.