CT Lesion Model-Based Structural Allografts: Custom Fabrication and Clinical Experience

Reconstruction for Massive Proximal Tibial Bone Defects Using Patient‐Customized Three‐Dimensional‐Printed Metaphyseal Cones in Revision Total Knee Arthroplasty

Objective

To review the clinical outcomes of revision total knee arthroplasty (RTKA) with massive proximal tibial bone defects using patient‐customized three‐dimensional (3D) printed highly porous metaphyseal cones.

Methods

A retrospective study of all patients at our institution who underwent RTKA with the Anderson Orthopaedic Research Institute type III tibial defects using patient‐customized 3D‐printed highly porous metaphyseal cones was performed from 2016 to 2018. Seven patients were enrolled in this study. General results (age, sex, and body mass index); intraoperative results (interface compatibility and stability, and operating time); and perioperative complications (total blood loss, blood transfusion rate, and deep venous thrombosis) were recorded and analyzed. Clinical improvement and functional evaluation (survivorship of implant, improvement of Hospital for Special Surgery Score and McMaster Universities Osteoarthritis Index, and improvement of range of motion [ROM]), and radiographic improvement and implant evaluation (progressive radiolucent lines or radiographic loosening, and mechanical alignment) were evaluated at 2 weeks, 6 weeks, 3 months, 6 months, 1 year, 2 years, and then annually, postoperatively.

Results

The mean age at diagnosis was 68 (61–77) years. The mean follow‐up was 25.3 (19–36) months. At the latest follow‐up, no aseptic loosening, prosthetic joint infection, or other complications were noted. The mean Hospital for Special Surgery Score increased from 49 (39–63) to 78 (70–83) (P < 0.01), whereas the mean Western Ontario and McMaster Universities Osteoarthritis Index increased from 59 (46–73) to 26 (12–38) (P < 0.01). All patients achieved improved postoperative ROM with the mean flexion angle increasing from 66° (30°–80°) to 93° (80°–100°), and improved mechanical alignment with all hip–knee–ankle (HKA) angles within ±3°.

Conclusions

The patient‐customized 3D‐printed metaphyseal cone is useful technique for reconstructing massive proximal tibial bone defects, with encouraging clinical and radiological outcomes in RTKA.

[Quadriceps tendon insufficiency and rupture : Treatment options in total knee arthroplasty]

Quadriceps tendon injuries and insufficiencies in total knee arthroplasty are rare, but are followed by a devastating complication that left untreated leads to a complete loss of function of the knee. This review article summarizes the functional anatomy, risk factors, and the prevalence and diagnosis of quadriceps tendon injuries, in addition to the possible management options for partial and complete ruptures. The treatment options are adapted according to the extent of the loss of function (partial, complete) and the duration of the injury (acute vs chronic). Furthermore, the choice of treatment should take into account the quality and availability of primary tissue, the patient's general health, along with their likely functional requirements. Conservative treatment is often justified in partial ruptures with good results. Complete ruptures require surgical intervention and multiple operative techniques are described. Treatment options for acute ruptures include direct primary repair with autogenous or synthetic tissue augmentation. In the case of chronic insufficiency and a lack of soft-tissue surroundings, reconstruction with the aid of a muscle flap or allograft tissue can be considered. All surgical intervention techniques used so far have been fraught with complications and rarely lead to satisfactory results. A new surgical approach to the reconstruction and augmentation of the extensor mechanism consists of the use of a synthetic mesh. The technique is described here in detail.

Bone Regeneration Based on Tissue Engineering Conceptions - A 21st Century Perspective

The role of Bone Tissue Engineering in the field of Regenerative Medicine has been the topic of substantial research over the past two decades. Technological advances have improved orthopaedic implants and surgical techniques for bone reconstruction. However, improvements in surgical techniques to reconstruct bone have been limited by the paucity of autologous materials available and donor site morbidity. Recent advances in the development of biomaterials have provided attractive alternatives to bone grafting expanding the surgical options for restoring the form and function of injured bone. Specifically, novel bioactive (second generation) biomaterials have been developed that are characterised by controlled action and reaction to the host tissue environment, whilst exhibiting controlled chemical breakdown and resorption with an ultimate replacement by regenerating tissue. Future generations of biomaterials (third generation) are designed to be not only osteoconductive but also osteoinductive, i.e. to stimulate regeneration of host tissues by combining tissue engineering and in situ tissue regeneration methods with a focus on novel applications. These techniques will lead to novel possibilities for tissue regeneration and repair. At present, tissue engineered constructs that may find future use as bone grafts for complex skeletal defects, whether from post-traumatic, degenerative, neoplastic or congenital/developmental "origin" require osseous reconstruction to ensure structural and functional integrity. Engineering functional bone using combinations of cells, scaffolds and bioactive factors is a promising strategy and a particular feature for future development in the area of hybrid materials which are able to exhibit suitable biomimetic and mechanical properties. This review will discuss the state of the art in this field and what we can expect from future generations of bone regeneration concepts.