Development and investigation of the applicability of computed tomography data-based modelling technique for polymeric high-density foams

As foams have become very important in several areas and since characterizing their properties is a crucial task, a finite element simulation model for high-density closed cell foams based on computed tomography (CT) measurements is developed. The model includes realistic microstructural features like cell size distribution due to the utilization of CT data. Moreover, a ‘skin-core-skin’ microstructure resulting from the manufacturing process (injection moulding) of the foams is also considered in the model. The mechanical behaviour of the foam’s core layer under tension and compression load is characterized based on the microstructural model to develop constitutive material models of the foam. These constitutive models enable further mechanical characterization of the foam with less computational effort. Compression and bending test simulations of injection moulded foams with three different densities are validated with corresponding experimental results. Thus, conclusions can be drawn regarding the reliability, applicability and possible further extensions of the high-density foam model.

Thermal and mechanical characterization of thermoplastic orthodontic aligners discs after molding process

Polymeric aesthetic aligners were introduced in orthodontics as an innovative alternative to fixed appliances, however, their compositions and the thermal molding process may influence the biomechanical characteristics of these aligners. In this study four different clear aligner brands were used, ACE 035 Essix, C + Essix, Crystal 0.75 and Crystal 1.0, whose aim was to identify the thermal-processing influence on the mechanical and physicochemical properties of these materials, and to suggest a orthodontic sequence of wear for these appliances to achieve more effective treatment results. For the tensile tests the sample size calculation was based on probability distributions from the F test. The effect size used was 0.3, type 1 error of 0.05. Statistical Yield strength and Young's Modulus results were evaluated using the Shapiro-Wilk test. The groups were compared using the parametric test of analysis of variance, with Tukey post-test. Differences were statistically considered at the p < 0.05. The Infrared spectroscopy analysis showed no changes in the samples' chemical structure after thermal-processing. However, in the polypropylene aligner, differences were verified in the region attributed to the crystalline phase. Differential Scanning Calorimetry analysis for the same sample showed a crystallinity fraction decrease due to relaxation between polymer chains after molding. In the tensile tests evaluated, the tensile strength and 'Young's modulus presented higher values for aligners containing 100% polyethylene terephthalate glycol. Performing an analogy exercise of the properties of orthodontic wires used in conventional fixed appliances and, relating them to orthodontic plastics, aligners composed of different materials and/or thicknesses could be used in increasing sequence in terms of the modulus of elasticity, starting with C+, which has a lower elastic modulus value, using the ACE 035 as an intermediate and finishing with the Crystal 0.75 and 1.0, providing the desired stiffness to the aligners for the final phase.

Effects of Injection Molding Process Parameters on the Chemical Foaming Behavior of Polypropylene and Polystyrene

In the present study, semi-crystalline polypropylene (PP) and amorphous polystyrene (PS) were adopted as matrix materials. After the exothermic foaming agent azodicarbonamide was added, injection molding was implemented to create samples. The mold flow analysis program Moldex3D was then applied to verify the short-shot results. Three process parameters were adopted, namely injection speed, melt temperature, and mold temperature; three levels were set for each factor in the one-factor-at-a-time experimental design. The macroscopic effects of the factors on the weight, specific weight, and expansion ratios of the samples were investigated to determine foaming efficiency, and their microscopic effects on cell density and diameter were examined using a scanning electron microscope. The process parameters for the exothermic foaming agent were optimized accordingly. Finally, the expansion ratios of the two matrix materials in the optimal process parameter settings were compared. After the experimental database was created, the foaming module of the chemical blowing agents was established by Moldex3D Company. The results indicated that semi-crystalline materials foamed less due to their crystallinity. PP exhibits the highest expansion ratio at low injection speed, a high melt temperature, and a low mold temperature, whereas PS exhibits the highest expansion ratio at high injection speed, a moderate melt temperature, and a low mold temperature.

Application of computed tomography data–based modelling technique for polymeric low density foams, Part A: Model development

In this research study, a methodology is introduced for generating finite element simulation models for low density closed cell foams based on computed tomography (CT) measurement results. Creating this kind of simulation models can be very expensive with regard to modelling and computational effort. Hence, a combined modelling technique based on CT data and Voronoi diagrams is developed that minimizes this effort, but nevertheless, generates simulation models with a realistic microstructure. In this article, the generation of simulation models using this modelling method and the necessary adaptation of the models concerning microstructural features to consider, for example, anisotropic properties of the foam, are described. Furthermore, simulations are performed to investigate the mechanical performance of the foam models and to compare the results with several analytical models and experimental data. Finally, conclusions regarding the applicability and possible further extensions of the model are provided.

Polyolefinic nanocomposite foams: Review of microstructure-property relationships, applications, and processing considerations

In this review, we survey the state of the art on polymeric foams incorporating nano-scale fillers. Particular focus of the review is on foams from polyolefinic nanocomposite formulations incorporating a wide variety of fillers. The nano-scale additives can influence the foam structure and properties in two ways: Firstly, they can act as composite reinforcement to enhance the mechanical properties and functionality of the matrix polymer; and secondly, they can act as foaming-processing aids through modification of the rheological, thermal and crystallization properties of the matrix as well as serving as heterogeneous nucleation sites. Through a combination of these influences, and using advanced processing techniques it is possible to achieve nanocomposite foams that have higher cell density, and more uniform cell size or controlled cell-size distribution. Such controlled foam morphologies, in turn, can yield better specific mechanical properties resulting in more effective light-weighting solutions. Further, the nano-scale additives can impart additional desired functionality resulting in multi-functional foams. In this article, we provide an overview of the mechanical, thermal and a few other relevant functional properties – such as piezoelectric sensitivity, acoustics, and filtration efficiency – of foams prepared using nanocomposite formulations, along with the processing considerations for achieving high quality foams using such materials.

Increasing cell density/decreasing cell size to produce microcellular and nanocellular thermoplastic foams: A review

Nowadays, polymeric foams have attracted particular attention in scientific and industrial societies due to their unique properties, such as high strength to weight ratio, excellent thermal and sound insulation, and low cost. Researchers have shown that the extraordinary properties of polymeric foams such as superior thermal insulation, can be achieved by increasing the cell density/decreasing the cell size. In this regard, firstly, the most important foaming processes, i.e. batch, extrusion, and injection molding are studied in the present research. Then, cell nucleation stage as the most crucial phenomenon for achieving high cell density/small cell size is investigated in detail. In the next step, the most important researches in the field of polymeric foams are introduced in which the largest cell densities/smallest cell sizes have been achieved. The investigations show that the most remarkable results (highest cell densities/smallest cell sizes) belong to the batch process. Also, the use of nucleating agents, increasing the solubility of blowing agent into the polymer, and the use of nanoparticles are the most efficient solutions to achieve microcellular and nanocellular structures.

Carbon particulate and controlled-hydrolysis assisted extrusion foaming of semi-crystalline polyethylene terephthalate for the enhanced thermal insulation property

This work presents a facile method to produce low-density PET foams using pristine semi-crystalline resin by moisture-induced controlled-hydrolysis in a tight processing window (moisture content ∼ 0.12 wt.%). We investigated the effect of moisture and moisture containing activated carbon (AC) on the foam expansion ratio, cell morphology, and PET resin degradation and crystallization properties. Controlled-hydrolysis increased the melt-flow rate of PET resin (intrinsic viscosity: 0.52 to 0.54 dL/g) without losing crystallinity, and thus the PET foams possess better tensile properties (∼2 MPa stress and ∼100% strain) and higher thermal stability (>200°C) than chemically modified PET foams. The foam density could be made as low as ∼ 0.15 g/cm3 using a lab scale twin-screw extruder. A strand array die was also designed to produce plate-shaped foam samples. AC allowed easier control of the moisture content and delayed resin degradation in extrusion. Both AC and micrographite (mGr) could stabilize the PET foam morphology in extrusion and serve as good infrared attenuation agents (IAAs) in a simulated housing thermal insulation experiment.

Structural Foams of Biobased Isosorbide-Containing Copolycarbonate

Isosorbide-containing copolycarbonate (Bio-PC) is a partly biobased alternative to conventional bisphenol A (BPA) based polycarbonate (PC). Conventional PC is widely used in polymer processing technologies including thermoplastic foaming such as foam injection molding. At present, no detailed data is available concerning the foam injection molding behavior and foam properties of Bio-PC. This contribution provides first results on injection-molded foams based on isosorbide-containing PC. The structural foams were produced by using an endothermic chemical blowing agent (CBA) masterbatch and the low pressure foam injection molding method. The influence of weight reduction and blowing agent concentration on general foam properties such as density, morphology, and mechanical properties was studied. The test specimens consist of a foam core in the center and compact symmetrical shell layers on the sides. The thickness of the foam core increases with increasing weight reduction irrespective of the CBA concentration. The specific (mechanical) bending properties are significantly improved and the specific tensile properties can almost be maintained while reducing the density of the injection-molded parts.

Study on reducing sink mark depth of a microcellular injection molded part with many reinforcing ribs

As a novel injection molding process, microcellular injection molding process has the characteristics of saving material, decreasing warpage and surface sink mark, improving dimensional accuracy, etc. But for the plastic part with thick reinforcing ribs, if selection of process parameters are not reasonable, foaming quality of melt will be affected and obvious sink mark defects will appear on the surface of plastic part. This paper selected a medical appliance shell with many reinforcing ribs as research object. Simulation experiments of microcellular injection molding process were performed by using orthogonal experiment method. The influence of different process parameters, such as mold cavity surface temperature, melt temperature, injection rate, cooling time, weight reduction ratio and supercritical fluid level, on the surface sink mark of microcellular injection molding part was studied by using signal-to-noise ratio analysis and analysis of variance . The results showed that mold cavity surface temperature was the most important influence factor on surface sink mark depth of microcellular injection molding part, followed by weight reduction ratio, cooling time, supercritical fluid level, injection rate and melt temperature. Meanwhile, the optimal combination of process parameters was obtained for minimizing sink mark depth of microcellular injection molding part. The average surface sink mark depth of microcellular injection molding part molded by using the optimized process parameters was only 2.62 µm, compared to 4.87 µm of average surface sink mark depth of microcellular injection molding part molded by using the process parameters before optimization, the average sink mark depth of microcellular injection molding part was reduced by 46.2%. Finally, the forming mechanism of sink mark of microcellular injection molding part at locations of reinforcing ribs was discussed, and the influence mechanism of different process parameters on surface sink mark defects of microcellular injection molding part was also analyzed.

Formation mechanism and structural characteristics of unfoamed skin layer in microcellular injection-molded parts

The microcellular injection-molded part usually consists of a foamed core region and two unfoamed skin layers on the cross section. This paper investigated the formation process, formation mechanism and structural characteristics of the unfoamed skin layers in microcellular injection-molded part. It is found that the unfoamed skin layers are formed in two processes namely “during filling” process and “after filling” process. The shear flow and the fountain flow behaviors of the melt in the filling stage are the main controlling factors on the formation of the unfoamed skin layer in “during filling” process, and the cooling solidification of the melt in cooling stage is the fundamental reason for the formation of the unfoamed skin layer in “after filling” process. Further studies found that the unfoamed skin layer in microcellular injection-molded part has two distinct regions, the outer region is a thin frozen layer which contains deformed and broken cells, and the inner region is a relatively thick solid-like layer which has no visible cells in. The unfoamed skin layer has a minimum thickness in the gate location. The whole thickness of the unfoamed skin layer is decreased with the increase of injection speed and mold temperature, but is slightly affected by melt temperature.

Injection molded components with functionally graded foam structures – Procedure and essential results

In the past few years, foam injection molding has increasingly gained significance in the field of technical plastic components. This is due to the development of new processes and processing combinations and efforts to produce lightweight products. In this article, a special tool technology will be introduced, which aids the process of expanding the existing areas of applications. The technology enables the production of foam injection molded components with different foaming ratios. This is made possible by core movements in the closed injection mold after the cavity has been filled volumetrically with plastic melt containing blowing agent. In doing so, functionally graded components with locally differing properties can be produced in one processing step. The method (pull and foam method) is based on the idea of equipping thin-walled components with locally foamed thick-volume elements – i.e. to increase the stiffness, create spacers, or joining surfaces. Simultaneously this method aims to exceed the limitations of conventional foam injection molding, especially with regard to scope for design. This article describes the procedure and characteristics of the process. Results with regard to the density in the differentially foamed areas, the morphology and the mechanical properties in correlation with the essential processing parameters are given.

Microcellular injection molding of polypropylene and glass fiber composites with supercritical nitrogen

Microcellular injection molding of polypropylene and glass fiber composites (PP-1684/GF-950) was performed using supercritical nitrogen as the physical blowing agent. Based on design of experiment matrices, the influences of glass fiber content and operating conditions on cell structure, glass fiber orientation and mechanical properties of molded samples were studied systematically. The results showed the cell morphology and glass fiber orientation of foaming parts were definitely influenced by the cooling and shear effects. The mechanical properties of foamed polypropylene–glass fiber composites could be effectively enhanced by improving the cell morphology, dispersion state and orientation of the glass fiber at optimal weight percentage [Formula: see text]. And the optimal conditions for injection molding were obtained by analyzing the signal-to-noise ratio analysis of the mechanical properties of the molded samples, which were a shot size of 36 mm, a supercritical N2 weight percentage of 0.4%, an injection speed of 60%, a melt temperature of 190℃ and a mold temperature of 70℃. The molded specimens of polypropylene–glass fiber composites, produced under those optimal conditions, exhibited very uniform fiber dispersion and microcellular structures with an average cell size less than 30 µm. And the mechanical properties normalized by weight ratio of the microcellular samples were increased significantly, especially the impact strength.