Diagnostic accuracy of dual-source and 320-row computed tomography angiography in detecting coronary in-stent restenosis: a systematic review and meta-analysis

In-Stent Restenosis

In-stent restenosis (ISR) remains a potential complication after percutaneous coronary intervention, even in the era of drug-eluting stents, and its treatment remains suboptimal. Neoatherosclerosis is an important component of the pathology of ISR and is accelerated in drug-eluting stents compared with bare-metal stents. Coronary angiography is the gold standard for evaluating the morphology of ISR, although computed tomography angiography is emerging as an alternative noninvasive modality to evaluate the presence of ISR. Drug-coated balloons and stent reimplantation are the current mainstays of treatment for ISR, and the choice of treatment should be based on clinical background and lesion morphology.

Use of Three-dimensional Printing in the Development of Optimal Cardiac CT Scanning Protocols

Three-dimensional (3D) printing is increasingly used in medical applications with most of the studies focusing on its applications in medical education and training, pre-surgical planning and simulation, and doctor-patient communication. An emerging area of utilising 3D printed models lies in the development of cardiac computed tomography (CT) protocols for visualisation and detection of cardiovascular disease. Specifically, 3D printed heart and cardiovascular models have shown potential value in the evaluation of coronary plaques and coronary stents, aortic diseases and detection of pulmonary embolism. This review article provides an overview of the clinical value of 3D printed models in these areas with regard to the development of optimal CT scanning protocols for both diagnostic evaluation of cardiovascular disease and reduction of radiation dose. The expected outcomes are to encourage further research towards this direction.

Personalized 3D printed coronary models in coronary stenting

Background

3D printing has shown great promise in cardiovascular disease, with reports mainly focusing on pre-surgical planning and medical education. Research on utilization of 3D printed models in simulating coronary stenting has not been reported. In this study, we presented our experience of placing coronary stents into personalized 3D printed coronary models with the aim of determining stent lumen visibility with images reconstructed with different postprocessing views and algorithms.

Methods

A total of six coronary stents with diameter ranging from 2.5 to 4.0 mm were placed into 3 patient-specific 3D printed coronary models for simulation of coronary stenting. The 3D printed models were placed in a plastic container and scanned on a 192-slice third generation dual-source CT scanner with images reconstructed with soft (Bv36) and sharp (Bv59) kernel algorithms. Thick and thin slab maximum-intensity projection (MIP) images were also generated from the original CT data for comparison of stent lumen visibility. Stent lumen diameter was measured on 2D axial and MIP images, while stent diameter was measured on 3D volume rendering images. 3D virtual intravascular endoscopy (VIE) images were generated to provide intraluminal views of the coronary wall and stent appearances.

Results

All of these stents were successfully placed into the right and left coronary arteries but 2 of them did not obtain wall apposition along the complete length. The stent lumen visibility ranged from 54 to 97%, depending on the stent location in the coronary arteries. The mean stent lumen diameters measured on 2D axial, thin and thick slab MIP images were found to be significantly smaller than the actual size (P<0.01). Thick slab MIP images resulted in measured stent lumen diameters smaller than those from thin slab MIP images, with significant differences noticed in most of the measurements (4 out of 6 stents) (P<0.05), and no significant differences in the remaining 2 stents (P=0.19-0.38). In contrast, 3D volume rendering images allowed for more accurate measurements with measured stent diameters close to the actual dimensions in most of these coronary stents, except for the stent placed at the right coronary artery in one of the models due to insufficient expansion of the stent. Images reconstructed with sharp kernel Bv59 significantly improved stent lumen visibility when compared to the smooth Bv36 kernel (P=0.01). 3D VIE was successfully generated in all of the datasets with clear visualization of intraluminal views of the stents in relation to the coronary wall.

Conclusions

This preliminary report shows the feasibility of using 3D printed coronary artery models in coronary stenting for investigation of optimal coronary CT angiography protocols. Future studies should focus on placement of more stents with a range of stent diameters in the quest to reduce the need for invasive angiography for surveillance.