Improvement in the healing of bone fractures using a cyclodextrin/Ni-MOF nanofibers network: the development of a novel substrate to increase the surface area with desirable functional properties

In this study, a β-cyclodextrins (β-CDs)/Ni-based MOF (β-CDs/Ni-based MOF) fibrous network with focus on biocompatible and biodegradable properties was used as a new material for orthopedic applications. The final products were synthesized by an efficient, rapid, and controllable electrospinning route under optimal conditions, including a flow rate of 0.3 mL g-1, applied voltage of 18 kV, and spinning distance of 20 cm. Efficient characterization by various analyzes showed that the β-CDs/Ni-based MOF fibrous nanostructures had a thermal stability at about 320 °C and homogeneous particles with a narrow size distribution. The BET analysis results showed a specific surface area of 2140 m2 g-1 for these compounds, which facilized potential conditions needed for the application of these compounds as a new substrate to improve the healing of bone fractures. The results showed the better porosity of the β-CDs/Ni-based MOF scaffolds as an essential property, leading to higher proliferation and nutrition and oxygen delivery, resulting in more tissue regeneration. This study proposes a novel strategy for a fibrous network substrate with distinct properties for orthopedic purposes.

Chitosan/Xanthan/Hydroxyapatite-graphene oxide porous scaffold associated with mesenchymal stem cells for dentin-pulp complex regeneration

The aim of this paper was to synthesize and characterize polymeric scaffolds of Chitosan/Xanthan/Hydroxyapatite-Graphene Oxide nanocomposite associated with mesenchymal stem cells for regenerative dentistry application. The chitosan-xanthan gum (CX) complex was associated with Hydroxyapatite-Graphene Oxide (HA-GO) nanocomposite with different Graphene Oxides (GO) concentration (0.5 wt%; 1.0 wt%; 1.5 wt%). The scaffolds characterizations were performed by X-ray diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR), Raman spectroscopy, thermogravimetric analysis (TGA), scanning electron microscopy (SEM) and contact angle. The mechanical properties were assessed by compressive strength. The in vitro bioactivity and the in vitro cytotoxicity test (MTT test) were analyzed as well. The data was submitted to the Normality and Homogeneity tests. In vitro Indirect Cytotoxicity assay data was statistically analyzed by ANOVA two-way, followed by Tukey's test (α = 0.05). Compressive strength and contact angle data were statistically analyzed by one-way ANOVA, followed by Tukey's test (α = 0.05). XRD showed the presence of Hydroxyapatite (HA) peaks in the structures CXHA, CXHAGO 0.5%,1.0% and 1.5%. FT-IR showed amino and carboxylic bands characteristic of CX. Raman spectroscopy analysis evidenced a high quality of the GO. In the TGA it was observed the mass loss associated with the CX degradation by depolymerization. SEM analysis showed pores in the scaffolds, in addition to HA incorporated and adhered to the polymer. Contact angle test showed that scaffolds have a hydrophilic characteristic, with the CX group the highest contact angle and CXHA the lowest (p < 0.05). 1.0 wt% GO significantly increased the compressive strength compared to other compositions. In the bioactivity test, the apatite crystals precipitation on the scaffold surface was observed. MTT test showed high cell viability in CXHAGO 1.0% and CXHAGO 1.5% scaffold. CXHAGO scaffolds are promising for regenerative dentistry application because they have morphological characteristics, mechanical and biological properties favorable for the regeneration process.

Design strategies for composite matrix and multifunctional polymeric scaffolds with enhanced bioactivity for bone tissue engineering

Over the past few decades, various bioactive material-based scaffolds were investigated and researchers across the globe are actively involved in establishing a potential state-of-the-art for bone tissue engineering applications, wherein several disciplines like clinical medicine, materials science, and biotechnology are involved. The present review article's main aim is to focus on repairing and restoring bone tissue defects by enhancing the bioactivity of fabricated bone tissue scaffolds and providing a suitable microenvironment for the bone cells to fasten the healing process. It deals with the various surface modification strategies and smart composite materials development that are involved in the treatment of bone tissue defects. Orthopaedic researchers and clinicians constantly focus on developing strategies that can naturally imitate not only the bone tissue architecture but also its functional properties to modulate cellular behaviour to facilitate bridging, callus formation and osteogenesis at critical bone defects. This review summarizes the currently available polymeric composite matrices and the methods to improve their bioactivity for bone tissue regeneration effectively.

Highly resilient porous polyurethane composite scaffolds filled with whitlockite for bone tissue engineering

The present work is intended to provide a base for further investigation of the composite scaffolds for bone tissue engineering, and whitlockite/polyurethane (WH/PU) scaffolds, in particular. WH Ca₁₈Mg₂(HPO₄)₂(PO₄)₁₂ was successfully prepared by means of a chemical reaction between Ca(OH)₂, Mg(OH)₂ and H₃PO₄. WH/PU scaffolds were synthesized via in situ polymerization. Synthesized WH particles and WH/PU composite scaffolds were characterized using FTIR, XRD, SEM and EDS. The porosity of scaffolds was calculated by the liquid displacement method. The water contact angle of scaffolds was tested. Mechanical characterization of WH/PU composite scaffolds was evaluated according to monotonic and cyclic compression examination. MC3T3-E1 cells were employed to evaluate the cytocompatibility of scaffolds. The results showed that WH and PU were completely integrated into composite biomaterials. The maximum compressive strength and elastic modulus of WH/PU composite scaffold reached up to 5.2 and 14.1 MPa, respectively. WH/PU composite scaffold had maximum 73% porosity. The minimum contact angle of WH/PU composite scaffold was 89.16°. WH/PU composite scaffolds have a good elasticity. Cyclic compression tests showed that scaffold could recover 90% of its original shape 1 h after removing the load. WH/PU composite scaffolds exhibited a high affinity to MC3T3-E1 cells. WH/PU composite scaffolds significantly promoted proliferation and alkaline phosphatase activity of MC3T3-E1 cells when compared to those grown on tissue culture well plates. It is suggested that the WH/PU scaffolds might be suitable for the application of bone tissue engineering.

Protective effects of resveratrol against genotoxicity induced by nano and bulk hydroxyapatite in Drosophila melanogaster

Hydroxyapatite (HAp) is a naturally occurring calcium phosphate mineral predominantly used for its biocompatibility in a number of areas such as bone grafting, prosthesis coating in dentistry, and targeted drug delivery. Since the nano form of HAp (nHAp) has gained popularity attributed to a re-mineralizing effect in dental repair procedures, concerns have been raised over safety and biocompatibility of these nanoparticles (NP). This study, therefore, aimed to (1) investigate mechanisms of potential genotoxicity and enhanced generation of reactive oxygen species (ROS) initiated by bulk and nano forms of HAp and (2) test in vivo whether resveratrol, a type of natural phenol, might mitigate the extent of potential DNA damage. The size of nHAp was determined to be 192.13 ± 9.91 nm after dispersion using transmission electron microscopy (TEM). Drosophila melanogaster was employed as a model organism to determine the genotoxic potential and adverse effects of HAp by use of (comet assay), mutagenic and recombinogenic activity (wing spot test), and ROS-mediated damage. Drosophila wing-spot tests demonstrated that exposure to nontoxic bulk and nHAp concentrations (1, 2.5, 5 or 10 mM) produced no significant recombination effects or mutagenicity. However, bulk and nHAp at certain doses (2.5, 5 or 10 mM) induced genotoxicity in hemocytes and enhanced ROS production. Resveratrol was found to ameliorate the genotoxic effects induced by bulk HAp and nHAp in comet assay. Data demonstrate that treatment with nano and bulk Hap-induced DNA damage and increased ROS generation D. melanogaster which was alleviated by treatment with resveratrol.

Exploring In Vitro Biological Cellular Responses of Pegylated β-Cyclodextrins

βCDPEG5 and βCDPEG2 are two derivatives comprising seven PEG linear chains of 5 and 2 kDa, respectively, conjugated to βCD. As βCDPEGs display different physicochemical properties than their precursors, they could also trigger distinct cellular responses. To investigate the biological behavior of βCDPEGs in comparison to their parent compounds, we performed broad toxicological assays on RAW 264.7 macrophages, MC3T3-E1 osteoblasts, and MDCK cells. By analyzing ROS and NO₂⁻ overproduction in macrophages, we found that βCDPEGs induced a moderate stress response without affecting cell viability. Although MC3T3-E1 osteoblasts were more sensitive than MDCK cells to βCDPEGs and the parent compounds, a similar pattern was observed: the effect of βCDPEG5 on cell viability and cell cycle progression was larger than that of βCDPEG2; PEG2 affected cell viability and cell cycle more than βCDPEG2; cell post-treatment recovery was favorable in all cases, and the compounds had similar behaviors regarding ROS generation. The effect on MDCK cell migration followed a similar pattern. In contrast, for osteoblasts, the interference of βCDPEG5 with cell migration was smaller than that of βCDPEG2; likewise, the effect of PEG2 was shorter than its conjugate. Overall, the covalent conjugation of βCD and PEGs, particularly to yield βCDPEG2, improved the biocompatibility profile, evidencing that a favorable biological response can be tuned through a thoughtful combination of materials. Moreover, this is the first time that an in vitro evaluation of βCD and PEG has been presented for MC3T3-E1 and MDCK cells, thus providing valuable knowledge for designing biocompatible nanomaterials constructed from βCD and PEGs.

Recent advances in tissue engineering scaffolds based on polyurethane and modified polyurethane

Organ repair, regeneration, and transplantation are constantly in demand due to various acute, chronic, congenital, and infectious diseases. Apart from traditional remedies, tissue engineering (TE) is among the most effective methods for the repair of damaged tissues via merging the cells, growth factors, and scaffolds. With regards to TE scaffold fabrication technology, polyurethane (PU), a high-performance medical grade synthetic polymer and bioactive material has gained significant attention. PU possesses exclusive biocompatibility, biodegradability, and modifiable chemical, mechanical and thermal properties, owing to its unique structure-properties relationship. During the past few decades, PU TE scaffold bioactive properties have been incorporated or enhanced with biodegradable, electroactive, surface-functionalised, ayurvedic products, ceramics, glass, growth factors, metals, and natural polymers, resulting in the formation of modified polyurethanes (MPUs). This review focuses on the recent advances of PU/MPU scaffolds, especially on the biomedical applications in soft and hard tissue engineering and regenerative medicine. The scientific issues with regards to the PU/MPU scaffolds, such as biodegradation, electroactivity, surface functionalisation, and incorporation of active moieties are also highlighted along with some suggestions for future work.

Preparation and Evaluation of Nanofibrous Hydroxypropyl Cellulose and β-Cyclodextrin Polyurethane Composite Mats

A series of nanofibrous composite mats based on polyurethane urea siloxane (PUUS), hydroxypropyl cellulose (HPC) and β-cyclodextrin (β-CD) was prepared using electrospinning technique. PUUS was synthesized by two steps solution polymerization procedure from polytetramethylene ether glycol (PTMEG), dimethylol propionic acid (DMPA), 4,4'-diphenylmethane diisocyanate (MDI) and 1,3-bis-(3-aminopropyl) tetramethyldisiloxane (BATD) as chain extender. Then, the composites were prepared by blending PUUS with HPC or βCD in a ratio of 9:1 (w/w), in 15% dimethylformamide (DMF). The PUUS and PUUS based composite solutions were used for preparation of nanofibrous mats. In order to identify the potential applications, different techniques were used to evaluate the chemical structure (Fourier transform infrared-attenuated total reflectance spectroscopy-FTIR-ATR), morphological structure (Scanning electron microscopy-SEM and Atomic force microscopy-AFM), surface properties (contact angle, dynamic vapors sorption-DVS), mechanical characteristics (tensile tests), thermal (differential scanning calorimetry-DSC) and some preliminary tests for biocompatibility and microbial adhesion.